We no longer need code that was introduced to differentiate
between two early versions of 8260.
We can remove this convoluted way to get the hardware version
that was needed because of a bug in the register's
configuration.
Moreover, since we no longer need to access the PRPH
registers, we no longer need to wake up the device,
request ownership, etc...
Remove all that.
This allows us to get the rid of the obsolete comment
about the AUX bus MISC address space which should have
been moved when this code was moved away from here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.4a5665ccd8a6.Iff3879405c15758ba661c430e77dc2160ddada1c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
Second set of patches for v5.8. Lots of new features and new supported
hardware for mt76. Also rtw88 got new hardware support.
Major changes:
rtw88
* add support for Realtek 8723DE PCI adapter
* rename rtw88.ko/rtwpci.ko to rtw88_core.ko/rtw88_pci.ko
iwlwifi
* stop supporting swcrypto and bt_coex_active module parameters on
mvm devices
* enable A-AMSDU in low latency
mt76
* new devices for mt76x0/mt76x2
* support for non-offload firmware on mt7663
* hw/sched scan support for mt7663
* mt7615/mt7663 MSI support
* TDLS support
* mt7603/mt7615 rate control fixes
* new driver for mt7915
* wowlan support for mt7663
* suspend/resume support for mt7663
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't support the FPGA versions of this card combination anymore.
Remove the cfg mangling that tries to load it and all the relevant
structures.
Change-Id: I190652101afcab682cfba873d062992f11efca32
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A couple of SoCs, which can be recognized by PCI device IDs 0xA0F0 and
0x43F0, need a longer wait for the xtal to stabilize. To handle this,
add a new trans_cfg structure for Qu devices with a larger
xtal_latency value and apply them to the devices recognized by these
IDs. Also add a flag that allows us to inform the FW that the low
latency xtal should be used.
Change-Id: I8a14c6af45ea14d8e7f1ef38a589158f38d0c0ea
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we identify the correct cfgs with the new tables for Qu step
C and QuZ with Jf, we can remove the mangling we do later on.
Change-Id: Ic01ce67db147e897ad2424f0e05a70a00d2c620e
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All the QnJ devices have a similar matching to the other Qu devices,
but needs a different configuration. Convert the QnJ devices to the
new table accordingly.
Change-Id: If236ef3d0da3e605a3379922818f5897e0affd7e
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new generic iwl_trans structures for these devices and apply the
correct cfg depending on the device characteristics.
Since we have to match Qu with IWL_CONFIG_ANY, we also need to move
the Hr devices to the new table, but for now we keep matching on PCI
device and subsystem device IDs.
Change-Id: I14e9146a99621ff11ce50bc746a4b88af508fee0
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to use different firmware versions for different HW steps with
certain devices. Prepare for this differentiation by adding HW step
to the new device table.
Change-Id: Ib1afb7b0c89e9dc2d26e6d32ea19e978c17ba1dd
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These values are selected based on the PCI device ID, so the decision
to use them can be made early. By moving them to the trans_cfg, we
avoid duplicating the large cfg structs for small pieces of
data (sometimes a single boolean). This will also allow us to make
more decisions based on, for instance, the SoC type in used.
The trans_cfg concept changes a bit, because previously it was used
only to boot the device before reading further characteristics and now
it also contains more data that is associated with the device ID.
Change-Id: Ib71b07ea9e322eb74571dc5e8aa58f17eece5c9c
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl9560_2ac_cfg struct is used for PNJ devices and the
configuration is the same as iwl9260_2ac_cfg, so we can remove the
former to avoid redundancy.
Change-Id: I17ac1802f00bd80006930b922a9fc21df60e3c16
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
First set of patches intended for v5.6
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
We have a lot of mostly duplicated data structures that are repeated
only because the device name string is different. To avoid this, move
the string from the cfg to the trans structure and add it
independently from the rest of the configuration to the PCI mapping
tables.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new device table that contains information that can be checked
at runtime in order to decide which configuration to use. This allows
us to map the full cfg independently from the tran-specific
configuration.
This is the first step in creating the new table. Subsequent patches
will add the possibility of checking different values at runtime in
order to make the decision.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With the new concept of separating the trans-specific (trans_cfg) data
from the rest of the cfg, we will start mapping only the trans_cfg
part to the PCI device ID/subsystem device ID. So we can assume that
the data passed to the probe function contains the trans_cfg, but
since the full cfg still contains the trans_cfg at the beginning, we
can allow a full cfg to be passed as well. This makes it easier to
convert the existing tables one by one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We needed this abstraction for some CSR registers for
IWL_DEVICE_22560, but that has been removed, so we don't need the
abstraction anymore. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
