Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.
Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by suspending all data tx queues by given percentage of time. The
thermal device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently rx tid setup is happening for TID 0 and TID 16
during peer setup. And if other TID packets received for
the peer it will be redirected to rx error ring and not through
reo ring. And this rx tid configuration cannot be done
in the rx error ring path since it is a atomic context.
So moving the rx tid setup for all tids during the peer setup.
This is required to enable PN offload functionality to route
all packets through reo ring.
Co-developed-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When there is WMI command failure, 'peer->sta' was not getting
cleaned up, and mac80211 frees the 'sta' memory, which is causing
the below page fault.
Cleaning up the sta pointer in ath11k whenever peer delete command
is sent.
Unable to handle kernel paging request at virtual address 200080000006a
pgd = ffffffc02a774000
[200080000006a] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
.
.
.
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.4.60 #1
Hardware name: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C1 (DT)
task: ffffffc00083c6d0 ti: ffffffc00083c6d0 task.ti: ffffffc00083c6d0
PC is at ath11k_dp_rx_process_mon_status+0x114/0x4e0 [ath11k]
LR is at ath11k_dp_rx_process_mon_status+0xe8/0x4e0 [ath11k]
pc : [<ffffffbffcf8e544>] lr : [<ffffffbffcf8e518>] pstate: 60000145
sp : ffffffc000833a30
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PPDU_CTRL type is missing in current pktlog dumps.
PPDU_CTRL is sent on CE5 with len 2560 bytes, current
driver ignores the payload len greter than 2048.
PPDU_CTRL of 2560 bytes is sent in two fragments of len 2028
and 532 bytes, but firmware reports pkt header has length as 2560
for both of the fragments.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In multi AP VAP scenario, when user bring down the interfaces. mac80211 mark
the interface down for the duplicated VAP and removed from the
local->interfaces list. ath11k_mac_get_arvif() is dependent on
ieee80211_iterate_active_interfaces_atomic() API to find the vdev id
in a given radio. In disassociation path, ath11k_mac_get_arvif() not
able to find the given vdev id since that VAP is removed from the
local->interfaces list. since sta_state callback throws error, mac80211 log
the below WARN_ON_ONCE message.
Fixed it by storing the allocated_vdev_map in each radio structure to maintain
the created vdev id bits. so that we can directly mask this against the given
vdev_id to find out the ar from the vdev_id.
WARN LOG:
WARNING: at net/mac80211/sta_info.c:1008
CPU: 2 PID: 2135 Comm: hostapd Not tainted #1
Hardware name: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C1 (DT)
task: ffffffc03a43d800 ti: ffffffc03a43d800 task.ti: ffffffc03a43d800
PC is at sta_set_sinfo+0x9dc/0xad4 [mac80211]
LR is at sta_set_sinfo+0x9cc/0xad4 [mac80211]
pc : [<ffffffbffce2a008>] lr : [<ffffffbffce29ff8>] pstate: 20000145
sp : ffffffc02cedb5f0
x29: ffffffc02cedb5f0 x28: ffffffc03a43d800
x27: 0000000000000014 x26: 0000000000000001
x25: ffffffc02cfc4000 x24: ffffffc036905508
x23: 0000000000000012 x22: ffffffc02cedb670
x21: ffffffc03bc64880 x20: ffffffc036904f80
x19: ffffffc02ae31000 x18: 00000000b019f3a1
x17: 0000000057f30331 x16: 00000000d8d1998e
x15: 0000000000000066 x14: 393a35383a36343a
x13: 6337203a6e6f6974 x12: 6174732065746169
x11: 636f737361736964 x10: 206f742064656c69
x9 : 6146203a31696669 x8 : 6337203a6e6f6974
x7 : 6174732065746169 x6 : ffffffc0008c33f6
x5 : 0000000000000000 x4 : 0000000000000000
x3 : 0000000000000000 x2 : 00000000ffffff92
x1 : 0000000000000000 x0 : ffffffbffcea1091
---[ end trace 63c4b1c527345d5a ]---
Call trace:
[<ffffffbffce2a008>] sta_set_sinfo+0x9dc/0xad4 [mac80211]
[<ffffffbffce2a2c4>] __sta_info_flush+0xec/0x130 [mac80211]
[<ffffffbffce3dc48>] ieee80211_nan_func_match+0x1a34/0x23e4 [mac80211]
[<ffffffbffcde03e0>] __cfg80211_stop_ap+0x60/0xf0 [cfg80211]
[<ffffffbffcdb6d08>] __cfg80211_leave+0x110/0x150 [cfg80211]
[<ffffffbffcdb6d78>] cfg80211_leave+0x30/0x48 [cfg80211]
[<ffffffbffcdb6fbc>] cfg80211_init_wdev+0x22c/0x808 [cfg80211]
[<ffffffc0000afe28>] notifier_call_chain+0x50/0x84
[<ffffffc0000afefc>] raw_notifier_call_chain+0x14/0x1c
[<ffffffc0004ae94c>] call_netdevice_notifiers_info+0x5c/0x6c
[<ffffffc0004ae96c>] call_netdevice_notifiers+0x10/0x18
[<ffffffc0004aea80>] __dev_close_many+0x54/0xc0
[<ffffffc0004aeb50>] dev_close_many+0x64/0xdc
[<ffffffc0004b0b70>] rollback_registered_many+0x138/0x2f4
[<ffffffc0004b0d4c>] rollback_registered+0x20/0x34
[<ffffffc0004b34b4>] unregister_netdevice_queue+0x68/0xa8
[<ffffffbffce3870c>] ieee80211_if_remove+0x84/0xc0 [mac80211]
[<ffffffbffce3e588>] ieee80211_nan_func_match+0x2374/0x23e4 [mac80211]
[<ffffffbffcdc29e8>] cfg80211_wext_giwscan+0x1000/0x1140 [cfg80211]
[<ffffffbffcb2a87c>] backport_genlmsg_multicast_allns+0x158/0x1b4 [compat]
[<ffffffc0004e0944>] genl_family_rcv_msg+0x258/0x2c0
[<ffffffc0004e09f4>] genl_rcv_msg+0x48/0x6c
[<ffffffc0004dfb50>] netlink_rcv_skb+0x5c/0xc4
[<ffffffc0004e06d8>] genl_rcv+0x34/0x48
[<ffffffc0004df570>] netlink_unicast+0x12c/0x1e0
[<ffffffc0004df9a4>] netlink_sendmsg+0x2bc/0x2dc
[<ffffffc00049a540>] sock_sendmsg+0x18/0x2c
[<ffffffc00049ab94>] ___sys_sendmsg+0x1bc/0x248
[<ffffffc00049ba24>] __sys_sendmsg+0x40/0x68
[<ffffffc00049ba5c>] SyS_sendmsg+0x10/0x20
[<ffffffc000085db0>] el0_svc_naked+0x24/0x28
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath11k_mac_get_ar_by_vdev_id() get protected under rcu lock
and unlock. peer association confirmation event get used this API
without rcu protection, so corrected it.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Parse and store the out-of-band rates reported by the FW.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will start using ieee80211_tx_status_ext() so we do not need to track
tx rates inside a struct ieee80211_tx_info. It is currently not possible
to populate that struct with HE rate info anyhow.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns a few times (trimmed for brevity):
../drivers/net/wireless/ath/ath11k/debugfs_sta.c:185:7: warning:
variable 'rate_idx' is used uninitialized whenever 'if' condition is
false [-Wsometimes-uninitialized]
It is not wrong, rate_idx is only initialized in the first if block.
However, this is not necessarily an issue in practice because rate_idx
will only be used when initialized because
ath11k_accumulate_per_peer_tx_stats only uses rate_idx when flags is not
set to RATE_INFO_FLAGS_HE_MCS, RATE_INFO_FLAGS_VHT_MCS, or
RATE_INFO_FLAGS_MCS. Still, it is not good to stick uninitialized values
into another function so initialize it to zero to prevent any issues
down the line.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Link: https://github.com/ClangBuiltLinux/linux/issues/832
Reported-by: ci_notify@linaro.org
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two error paths where "ret" wasn't set. Also one error path
we set the error code to -EINVAL but we should just preserve the error
code from ath11k_hal_srng_get_entrysize(). That function only returns
-EINVAL so this doesn't change anything.
I removed the "ret = 0;" initializers so that hopefully GCC will be able
to detect these sorts of bugs in the future.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add IEEE80211_RADIOTAP_HE_DATA1_BW_RU_ALLOC_KNOWN to the list of known
fields. Not doing so will result in wireshark not calculating the
bitrate correctly.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the unlikely event that cap->supported_bands has neither
WMI_HOST_WLAN_2G_CAP set or WMI_HOST_WLAN_5G_CAP set then pointer
band is null and a null dereference occurs when assigning
band->n_iftype_data. Move the assignment to the if blocks to
avoid this. Cleans up static analysis warnings.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 9f056ed8ee ("ath11k: add HE support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds missing rx rate info stats like pilot evm,
per chain rssi, per user ul ppdu and mpdu counts and
ul ofdma rate info etc.
And add null checks for memory alloc failures.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the structure ts is not inititalized and ts.flags contains
garbage values from the stack. This is being passed into function
ath11k_dp_tx_status_parse that bit-wise or'ing in settings into the
ts.flags field. To avoid flags (and other fields) from containing
garbage, initialize the structure to zero before use.
Addresses-Coverity: ("Uninitialized scalar variable)"
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The channel info parameters are required by the firmware to process TxBf
parameters. Currently TxBf is passed prior to the channel info. This patch
moves TxBf setup after the channel setup.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_ATH11K_DEBUGFS is disabled, but CONFIG_MAC80211_DEBUGFS
is turned on, the driver fails to build:
drivers/net/wireless/ath/ath11k/debugfs_sta.c: In function 'ath11k_dbg_sta_open_htt_peer_stats':
drivers/net/wireless/ath/ath11k/debugfs_sta.c:416:4: error: 'struct ath11k' has no member named 'debug'
ar->debug.htt_stats.stats_req = stats_req;
^~
It appears that just using the former symbol is sufficient here,
adding a Kconfig dependency takes care of the corner cases.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FIELD_SIZEOF() macro was redundant, and is being removed from the
kernel. Since commit c593642c8b ("treewide: Use sizeof_field() macro")
this is one of the last users of the old macro, so replace it.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Three of the WMI command handlers were not casting to the right data type.
Lets make the code consistent with the other handlers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The list iterator is always non-NULL so it doesn't need to be checked.
I also removed the unnecessary initializer because the list iterator is
always initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath11k_ce_alloc_ring() function returns error pointers on error, not
NULL. The rest of the driver assumes that "pipe->src_ring" is either
valid or NULL so this patch introduces a temporary varaible to avoid
leaving it as an error pointer.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The callers unlock this lock so this error path has a double unlock.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The error handling when the call to ath11k_hal_srng_get_entrysize fails
leaks skb, fix this by returning via the err_free return path that will
ensure the skb is free'd.
Addresses-Coverity: ("Resource leak")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable radioup is not uninitalized so it may contain a garbage
value and hence the detection of a radio that is not up is buggy.
Fix this by initializing it to zero.
Addresses-Coverity: ("Uninitalized scalar variable")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently a return path is leaking the previously allocate reg_info. Fix
this by exiting via the return path mem_free. Since the return value ret
is defaulted to 0, there is no need to re-assign ret to the 0 before
the goto.
Addresses-Coverity: ("Resource leak")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns:
drivers/net/wireless/ath/ath11k/wmi.c:1827:23: warning: implicit
conversion from enumeration type 'enum wmi_scan_priority' to different
enumeration type 'enum scan_priority' [-Wenum-conversion]
arg->scan_priority = WMI_SCAN_PRIORITY_LOW;
~ ^~~~~~~~~~~~~~~~~~~~~
1 warning generated.
wmi_scan_priority and scan_priority have the same values but the wmi one
has WMI prefixed to the names. Since that enum is already being used,
get rid of scan_priority and switch its one use to wmi_scan_priority to
fix this warning.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Link: https://github.com/ClangBuiltLinux/linux/issues/808
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are several spelling mistakes in warning and debug messages,
fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch sets the correct BA buffer size when we are in HE mode.
Without this change we are not able to receive 256 bitmapped BA frames.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The code currently uses the wrong pdev id when enabling TWT. Fix this by
using the correct ones.
Fixes: e65a616f4e74 ("ath11k: add TWT support")
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Moving the function into dp_tx.c allows gcc to optimize the code better
and also avoid chace invalidates and context switches.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the current code does 4 memcpys for each completion frame.
1) duplicate the desc
2 + 3) inside kfifo insertion
4) kfifo remove
The code simply drops the kfifo and uses a trivial ring buffer. This
requires a single memcpy for insertion. There is no removal needed as
we can simply use the inserted data for processing. As the code runs
inside the NAPI context it is atomic and there is no need for most of
the locking.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the fields are only used by debugfs. Move the parsing of these
from the data hot path to the debugfs code.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes the code consistent with the recent sc to ab rename.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no point in zero'ing out the structure if we set all values in the
following line.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After applying this setting the TX performance issue of STA interfaces is
gone and we can see TX performance go up to ~900mbit on HE80.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a WMI call helper to set the powersave mode of a STA interface.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The capabilities for the HE mesh are generated from the capabilities
reported by the fw. But the firmware only reports the overall capabilities
and not the one which are specific for mesh. Some of them (TWT, MU UL/DL,
TB PPDU, ...) require an infrastructure setup with a main STA (AP)
controlling the operations. This is not the case for mesh and thus these
capabilities are removed from the list of capabilities.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware expects all the required REO destination rings setup
while processing wmi_init command. Not doing this causes connected
stations getting disconnected and not able to connect back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is to prepare REO ring setup before sending wmi_init command.
Firmware expects all the required REO rings to be setup while processing
wmi_init command. But as per the current initialization sequence, REO ring
configurations are done only after wmi_init command is sent.
Also refactoring ath11k_mac_create() into ath11k_mac_alloc() and
ath11k_mac_register() to it mac80211 hw structure available before sending
wmi_init command.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently HTT_PPDU_STATS_TAG_USR_COMPLTN_ACK_BA_STATUS tag of PPDU stats
doesn't have valid success bytes info of management frames.
So skip update peer stats for management packets.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update tx duration in station info form PPDU stats
so that users can dump tx duration of the station.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Guard interval value which comes from VHT_SIG_A TLV has a mapping
where value 0 corresponds to LGI, 1 and 3 corresponds to SGI.
Value 3 which is SGI(0.4us) in VHT was incorrectly mapped to a GI
of 3.2us(only applicable in HE) resulting in incorrect rx GI stats.
Fixing the mapping.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
remove tail check to avoid last amsdu leak.
recycle skb in ppdu id wrap around case
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adverise MPDU start spacing as no restriction in ht capabilities,
Since IPQ8074 hw support all sorts of mpdu start spcing. With this
observed minor uplink performance improvement in lower data frame
size case with Veriwave clients.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the number of tx and rx chains properly on drv_set_antenna().
This will ensure the related ht/vht/he caps are properly recalculated
based on the tx/rx chains set.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
