The previous patch fixes a TEF vs. TX race condition, by first updating the TEF
tail pointer in hardware, and then updating the driver internal pointer.
The same pattern exists in the RX-path, too. This should be no problem, as the
driver accesses the RX-FIFO from the interrupt handler only, thus the access is
properly serialized. Fix the order here, too, so that the TEF- and RX-path look
similar.
Fixes: 1f652bb6ba ("can: mcp25xxfd: rx-path: reduce number of SPI core requests to set UINC bit")
Link: https://lore.kernel.org/r/20210105214138.3150886-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd driver uses a TX FIFO for sending CAN frames and a TX Event FIFO
(TEF) for completed TX-requests.
The TEF event handling in the mcp251xfd_handle_tefif() function has a race
condition. It first increments the tx-ring's tail counter to signal that
there's room in the TX and TEF FIFO, then it increments the TEF FIFO in
hardware.
A running mcp251xfd_start_xmit() on a different CPU might not stop the txqueue
(as the tx-ring still shows free space). The next mcp251xfd_start_xmit() will
push a message into the chip and the TX complete event might overflow the TEF
FIFO.
This patch changes the order to fix the problem.
Fixes: 68c0c1c7f9 ("can: mcp251xfd: tef-path: reduce number of SPI core requests to set UINC bit")
Link: https://lore.kernel.org/r/20210105214138.3150886-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.
Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de
Reported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The helper functions can_len2dlc and can_dlc2len are only relevant for
CAN FD data length code (DLC) conversion.
To fit the introduced can_cc_dlc2len for Classical CAN we rename:
can_dlc2len -> can_fd_dlc2len to get the payload length from the DLC
can_len2dlc -> can_fd_len2dlc to get the DLC from the payload length
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-6-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The naming of can_dlc as element of struct can_frame and also as variable
name is misleading as it claims to be a 'data length CODE' but in reality
it always was a plain data length.
With the indroduction of a new 'len' element in struct can_frame we can now
remove can_dlc as name and make clear which of the former uses was a plain
length (-> 'len') or a data length code (-> 'dlc') value.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201120100444.3199-1-socketcan@hartkopp.net
[mkl: gs_usb: keep struct gs_host_frame::can_dlc as is]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a reference to the recent released MCP2517FD and MCP2518FD
errata sheets and paste the explanation.
The single error correction does not always work, so always indicate that a
single error occurred. If the location of the ECC error is outside of the
TX-RAM always use netdev_notice() to log the problem. For ECC errors in the
TX-RAM, there is a recovery procedure.
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
Link: https://lore.kernel.org/r/20200925065606.358-1-thomas.kopp@microchip.com
[mkl: split into two patches, adjust subject and commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commits
653ee35ce6 ("can: hi311x: remove custom DMA mapped buffer")
Fixes: df58525df3 ("can: mcp251x: remove custom DMA mapped buffer")
both the hi3111x and the mcp251x driver don't make use of the DMA API
any more. So we can safely remove the HAS_DMA dependency.
While we're here, remove the unneeded CAN_DEV and SPI dependencies from
the CAN_HI311X symbol, as the parent menus already have these
dependencies.
Link: https://lore.kernel.org/r/20200915223527.1417033-24-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This prevents unwanted glitches on the outputs when changing the link
state of the can interface or when resuming from suspend. Only if the
device is powered off during suspend it needs to be resetted as required
by the specs.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch introduces the function mcp251x_write_2regs() to write two
registers with one SPI transfer and converts the disabling of pending
interrupts in mcp251x_stop() to it.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In mcp251x_restart_work_handler() the variable to stop the interrupt
handler (priv->force_quit) is reset after the chip is restarted and thus
a interrupt might occur.
This patch fixes the potential race condition by resetting force_quit
before enabling interrupts.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no need to check for regulator presence in the ->suspend()
since a wrapper does it for us. Due to this we may unconditionally set
AFTER_SUSPEND_POWER flag.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make use of device property API in this driver so that both OF based
system and ACPI based system can use this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). This comes with a small functional change: previously
all errors were ignored when platform data is present. Now all errors are
treated as errors. If no input clock is present devm_clk_get_optional() will
return NULL instead of an error which matches the behavior of the old code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the pre device-tree ARM aera there were board files that configured
the system (instead of a device tree). A "struct spi_board_info" was
used to describe the SPI bus.
As new systems should be described via device trees, this patch removes
the board setup example from the driver. The "struct
mcp251x_platform_data" cannot be removed completely, as there are still
some in-tree users of this file.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to duplicate what SPI core already does, i.e. mapping buffers
for DMA capable transfers. This patch removes all related pices of code.
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The MCP2515 datasheet clearly describes a level-triggered interrupt pin.
Therefore the receiving interrupt controller must also be configured for
level-triggered operation otherwise there is a danger of a missed
interrupt condition blocking all subsequent interrupts. The ONESHOT
flag ensures that the interrupt is masked until the threaded interrupt
handler exits.
Rather than change the flags globally (they must have worked for at
least one user), keep the old behavior for for non DT devices. DT based
devices specify the flags in their corresonding DT node.
See: https://github.com/raspberrypi/linux/issues/2175https://github.com/raspberrypi/linux/issues/2263
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Passing driver name as name during request_threaded_irq() results in all
CAN IRQs have same name. This does not help much to easily identify which
IRQ belongs to which CAN instance. Therefore pass dev_name() during
request_threaded_irq() so that better identifiable name is listed for
CAN devices in cat /proc/interrupts output.
Output of cat /proc/interrupts
Before this patch:
253: 2 gpio-mxc 13 Edge mcp251x
259: 2 gpio-mxc 19 Edge mcp251x
After this patch:
253: 2 gpio-mxc 13 Edge spi1.1
259: 2 gpio-mxc 19 Edge spi1.2
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some boards take longer than 5ms to power up after a reset, so allow
some retries attempts before giving up.
Fixes: ff06d611a3 ("can: mcp251x: Improve mcp251x_hw_reset()")
Cc: linux-stable <stable@vger.kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
