Currently the DPLL .get_freq() uses pll->state.hw_state which
is not the thing we actually read out (except during driver
load/resume). Outside of that pll->state.hw_state is just the
thing we committed last time around. During state check we
just read the thing into crtc_state->dpll_hw_state, so that
is what we should use for calculating the DPLL output frequency.
I think we used to do this so that the results of the readout
were actually used, but somehow it got changed when the
.get_freq() refactoring happened.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109231239.17002-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Store the relative data rate for planes in the crtc state
so that we don't have to use
intel_atomic_crtc_state_for_each_plane_state() to compute
it even for the planes that are no part of the current state.
Should probably just nuke this stuff entirely an use the normal
plane data rate instead. The two are slightly different since this
relative data rate doesn't factor in the actual pixel clock, so
it's a bit odd thing to even call a "data rate". And since the
watermarks are computed based on the actual data rate anyway
I don't really see what the point of this relative data rate
is. But that's for the future...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106173042.7534-6-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
In order to remove intel_atomic_crtc_state_for_each_plane_state()
from skl_crtc_can_enable_sagv() we can simply precompute whether
each wm level can tolerate the SAGV block time latency or not.
This has the nice side benefit that we remove the duplicated
wm level latency calculation. In fact the copy of that code
we had in skl_crtc_can_enable_sagv() didn't even handle
WaIncreaseLatencyIPCEnabled/Display WA #1141 whereas the copy
in skl_compute_plane_wm() did. So now we just have the one
copy which handles all the w/as.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106173042.7534-5-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
[Why]
After removing added latency for HostVM by default, DDR4 sr exit
latencies were no longer large enough for some panels and caused
underflow.
[How]
Add 1us to sr enter/exit watermark.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should use int for counting variable
[How]
Change type from bool to uint32_t
Signed-off-by: Raymond Yang <rayyang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Instead of calculating CRC on whole frame, add flexibility to calculate
CRC on specific frame region.
[How]
Add few crc window coordinate properties. By default, CRC is calculated
on whole frame unless user space specifies the CRC calculation window.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add a dual edp power optimization flag, so driver will
notify this flag to dmub FW to determine if apply the
power optimization.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Blue screen when PNP with multiple monitor or hotplug external monitor when playing video
due to dpp dto isn't programmed properly.
If lower dpp clock, dpp dto need to be programmed first, and actual dpp clk not avalable yet.
[How]
set dpp dto as per request clk for lower case before dpp clk update, and after dpp clk updated
set dpp dto again with actual dpp clk.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The I2C memory blocks should be powered down when they are not in use.
This will reduce power consumption.
[How]
1. Write to I2C_LIGHT_SLEEP_FORCE to put memory in light sleep when
released
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Check if the eDP sink supports the dynamic backlight control
[How]
Query the dynamic backlight capability in DPCD (eDP case only)
Signed-off-by: Roy Chan <roy.chan@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor is missing on displays 2 and up when doing rotated
display groups in 1xnY setup. Calculation puts cursor
out of bounds so it is not enabled.
[How]
In dcn10_set_cursor_position(), add in viewport.y into cursor
calculations for 1xnY rotated display groups.
For pipe split, check viewport.y for both pipes and use lower one
to normalize cursor position before calculations.
Add odm 2:1 support ( using same calculations as pipe split ).
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Currently if VBIOSSMC_Result_UnknownCmd is returned as result of smu msg
there is no way to know. Put 1 in param so if 1 is returned, this unknown case is handled.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the system does not have hostvm enabled, disabling it for
DML validation will allow more modes to pass at lower voltage
levels.
[How]
When initializing HostVM save state to hubbub and read back
when populating DML pipes from context.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Use GPINT command to get PSR residency from FW.
[How]
Hook up PSR residency command to DSAT.
Since PSR Count Request is deprecated, we will use this.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dpp dto phase and modulo are programmed with actual dpp global clk
and pipe clk. Need to use actual dpp clk to prgoram dpp dto modulo
to get more accuracy ratio.
[How]
assign actual dpp clk to dccg for dpp modulo programming.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to add the fine grain tuning function for vangogh.
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should be
limited in the safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value
instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the setting target values by "s" command
will take effect.
Example:
1)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
2)use "s" -- set command to configure the min or max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "r" -- reset command to restore the min and max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_do_test_moves() is failing because of wrong
usable gart size calculation and throwing:
[drm:amdgpu_do_test_moves [amdgpu]] *ERROR* 0000000020bdc9f3 bind failed
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We've fixed many races in panfrost_job_timedout() but some remain.
Instead of trying to fix it again, let's simplify the logic and move
the reset bits to a separate work scheduled when one of the queue
reports a timeout.
v5:
- Simplify panfrost_scheduler_stop() (Steven Price)
- Always restart the queue in panfrost_scheduler_start() even if
the status is corrupted (Steven Price)
v4:
- Rework the logic to prevent a race between drm_sched_start()
(reset work) and drm_sched_job_timedout() (timeout work)
- Drop Steven's R-b
- Add dma_fence annotation to the panfrost_reset() function (Daniel Vetter)
v3:
- Replace the atomic_cmpxchg() by an atomic_xchg() (Robin Murphy)
- Add Steven's R-b
v2:
- Use atomic_cmpxchg() to conditionally schedule the reset work
(Steven Price)
Fixes: 1a11a88cfd ("drm/panfrost: Fix job timeout handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105151704.2010667-1-boris.brezillon@collabora.com
intel_atomic_crtc_state_for_each_plane_state() peeks at the
plane's current state without holding the plane's mutex, trusting
that the crtc's mutex will protect it. In practice that does work
since our planes can't move between pipes, but it sets a bad
example. intel_atomic_crtc_state_for_each_plane_state() also
relies on crtc_state.uapi.plane_mask which may be full of lies
when it comes to the bigjoiner stuff, so soon we can't use it as
is anyway. So best to just get rid of it entirely. Which we can
easily do by switching to the g4x/vlv "raw" watermark approach.
Later on we should even be able to move the "raw" watermark
computation into the normal .plane_check() code, leaving only
the merging/clamping of the final watermarks to the later
stages. But that will require adjusting the ilk+ wm code
similarly as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106173042.7534-3-ville.syrjala@linux.intel.com
Copy over the width/height in millimeters to the
(somewhat redundant) display info, and set up the
bus format and bus flags for the display.
When used as DPI this display requires DE to be
active low and pixel data to be output on the
negative edge. It might be that it was previously
used with a display controller that either does
not support these settings or was hardcoded to use
these as default. This information comes from the
source code of the Samsung GT-I9070 mobile phone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110234653.2248594-6-linus.walleij@linaro.org
