Current code initializes HDMI PHY clock driver before reset line is
deasserted and clocks enabled. Because of that, initial readout of
clock divider is incorrect (0 instead of 2). This causes any clock
rate with divider 1 (register value 0) to be set incorrectly.
Fix this by moving initialization of HDMI PHY clock driver after reset
line is deasserted and clocks enabled.
Cc: stable@vger.kernel.org # 4.17+
Fixes: 4f86e81748 ("drm/sun4i: Add support for H3 HDMI PHY variant")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190514204337.11068-2-jernej.skrabec@siol.net
H6 has Synopsys DWC HDMI 2.0 TX PHY.
There is no freely available documentation for it, only code found in
BSP kernel. However, judging by the code, PHY is very similar to older
Synopsys HDMI PHY described in i.MX6 documentation. Most registers seem
to be the same.
According to i.MX6 documentation, mpll settings are based on pixel clock
and are not specific to each SoC. Because of that, mpll table in this
commit is based on that documentation and not on BSP code. Other PHY
settings were derived from BSP PHY driver code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-23-jernej.skrabec@siol.net
Currently sun8i-hdmi-phy driver supports only custom PHYs connected to
DW HDMI controller. Since newest Allwinner SoCs have unmodified Synopsys
PHY, driver has to be reorganized to support them.
Variant structure is expanded to allow differentiation between custom
and Sysnopsys PHYs and to hold Synopsys PHY settings.
Since DW HDMI bridge platform data has different fields for custom and
Sysnopsys PHY, function sun8i_hdmi_phy_get_ops() is replaced with
sun8i_hdmi_phy_set_ops().
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-22-jernej.skrabec@siol.net
While A83T HDMI PHY seems to be just customized Synopsys HDMI PHY, H3
HDMI PHY is completely custom PHY.
However, they still have many things in common like clock and reset
setup, setting sync polarity and more.
Add support for H3 HDMI PHY variant.
While documentation exists for this PHY variant, it doesn't go in great
details. Because of that, almost all settings are copied from BSP linux
4.4. Interestingly, those settings are slightly different to those found
in a older BSP with Linux 3.4. For now, no user visible difference was
found between them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180301213442.16677-13-jernej.skrabec@siol.net
Current polarity configuration code is cleary wrong since it compares
same flag two times. However, even if flag name is fixed, it won't work
well for resolutions which have one polarity positive and another
negative.
Fix that by properly set each bit according to each polarity. Since
those two bits are not described in any documentation, relationships
were obtained by experimentation.
Fixes: b7c7436a5f ("drm/sun4i: Implement A83T HDMI driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180301213442.16677-10-jernej.skrabec@siol.net
