Add an hook to initialize the vector routing table with the default
values before MSIx is enabled.
The new function set_msix_rttable() is called only if present in the
struct adf_hw_device_data of the device. This is to allow for QAT
devices that do not support that functionality.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Introduce support for devices that require multiple firmware images.
If a device requires more than a firmware image to operate, load the
image to the appropriate Acceleration Engine (AE).
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The arbiter configuration, the offset to the arbiter config CSR and the
offset to the worker thread to service arbiter CSR are going to be
different in QAT GEN4 devices although the logic that uses them is the
same across all QAT generations.
This patch reworks the gen-specific parts of the arbiter access code by
introducing the arb_info structure, that contains the values that are
generation specific, and a function in the structure adf_hw_device_data,
get_arb_info(), that allows to get them.
Since the arbiter values for QAT GEN2 devices (c62x, c3xxx and
dh895xcc) are the same, a single function, adf_gen2_get_arb_info() is
provided in adf_gen2_hw_data.c and referenced by each QAT GEN2 driver.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Introduce admin AE mask. If this mask set, the fw constant message is
sent only to engines that belong to that set, otherwise it is sent to
all engines.
This is in preparation for the qat_4xxx driver where the constant message
should be sent only to admin engines.
In GEN2 devices (c62x, c3xxx and dh895xcc), the admin AE mask is 0 and
the fw constants message is sent to all AEs.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The number of AE2FUNC_MAP registers is different in every QAT device
(c62x, c3xxx and dh895xcc) although the logic and the register offsets
are the same across devices.
This patch separates the logic that configures the iov threads in a
common function that takes as input the number of AE2FUNC_MAP registers
supported by a device. The function is then added to the
adf_hw_device_data structure of each device, and called with the
appropriate parameters.
The configure iov thread logic is added to a new file,
adf_gen2_hw_data.c, that is going to contain code that is shared across
QAT GEN2 devices.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This change is to allow support for QAT devices that may not have 16
rings per bank.
The rings structure in bank is allocated dynamically based on the number
of banks supported by a device.
Note that in the error path in adf_init_bank(), ring->inflights is set
to NULL after the free to silence a false positive double free reported
by clang scan-build.
Signed-off-by: Ahsan Atta <ahsan.atta@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kernel source code should not include stdint.h types.
This patch replaces uintXX_t types with respective ones defined in kernel
headers.
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move qat_isr.c and qat_isrvf.c files to qat_common dir
so that they can be reused by all devices.
Remove adf_drv.h files because thay are not longer needed.
Move adf_dev_configure() function to qat_common so it can be reused.
Also some minor updates to common code for multidevice.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adf admin and HW arbiter function can be used by dh895xcc specific code
well as the new dh895xccvf and future devices so moving them to
qat_common so that they can be shared.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The element pci_dev_id in the struct adf_hw_device_data is redundant since
the PCI device id can be retrieved from the struct pci_dev.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the device needs a reset, e.g. when an uncorrectable PCIe AER event
occurs, various services/data structures need to be cleaned up, the
hardware reset and the services/data structures initialized and started.
The code to perform the cleanup and initialization was not performed when
a device reset was done.
This patch moves some of the initialization code out of the .probe entry-
point into a separate function that is now called during probe as well as
after the hardware has been reset. Similarly, a new function is added for
first cleaning up these services/data structures prior to resetting. The
new functions are adf_dev_init() and adf_dev_shutdown(), respectively, for
which there are already prototypes but no actual functions just yet and are
now called when the device is reset and during probe/cleanup of the driver.
The down and up flows via ioctl calls has similarly been updated.
In addition, there are two other bugs in the reset flow - one in the logic
for determining whether to schedule a device reset upon receiving an
uncorrectable AER event which prevents the reset flow from being initiated,
and another with clearing the status bit indicating a device is configured
(when resetting the device the configuration remains across the reset so
the bit should not be cleared, otherwise, the necessary services will not
be re-started in adf_dev_start() after the reset - clear the bit only when
actually deleting the configuration).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto update from Herbert Xu:
- The crypto API is now documented :)
- Disallow arbitrary module loading through crypto API.
- Allow get request with empty driver name through crypto_user.
- Allow speed testing of arbitrary hash functions.
- Add caam support for ctr(aes), gcm(aes) and their derivatives.
- nx now supports concurrent hashing properly.
- Add sahara support for SHA1/256.
- Add ARM64 version of CRC32.
- Misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (77 commits)
crypto: tcrypt - Allow speed testing of arbitrary hash functions
crypto: af_alg - add user space interface for AEAD
crypto: qat - fix problem with coalescing enable logic
crypto: sahara - add support for SHA1/256
crypto: sahara - replace tasklets with kthread
crypto: sahara - add support for i.MX53
crypto: sahara - fix spinlock initialization
crypto: arm - replace memset by memzero_explicit
crypto: powerpc - replace memset by memzero_explicit
crypto: sha - replace memset by memzero_explicit
crypto: sparc - replace memset by memzero_explicit
crypto: algif_skcipher - initialize upon init request
crypto: algif_skcipher - removed unneeded code
crypto: algif_skcipher - Fixed blocking recvmsg
crypto: drbg - use memzero_explicit() for clearing sensitive data
crypto: drbg - use MODULE_ALIAS_CRYPTO
crypto: include crypto- module prefix in template
crypto: user - add MODULE_ALIAS
crypto: sha-mb - remove a bogus NULL check
crytpo: qat - Fix 64 bytes requests
...
In a system with NUMA configuration we want to enforce that the accelerator is
connected to a node with memory to avoid cross QPI memory transaction.
Otherwise there is no point in using the accelerator as the encryption in
software will be faster.
Cc: stable@vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Tested-by: Nikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix random config build warnings:
Implicit-function-declaration ‘__raw_writel’
Cast to pointer from integer of different size [-Wint-to-pointer-cast]
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a common infractructure that will be used by all Intel(R)
QuickAssist Technology (QAT) devices.
v2 - added ./drivers/crypto/qat/Kconfig and ./drivers/crypto/qat/Makefile
v4 - splits common part into more, smaller patches
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
