On non-DT platforms IRQ controllers associated with the GPIOs have a
fixed IRQ base value known at compile time. The sh-pfc driver translates
GPIO number to IRQ numbers using a hardcoded table. This mechanism
breaks on DT platforms, as the IRQ base values are dynamic in that case.
Fix this by specifying IRQs associated with GPIOs in IRQ resources,
populated automatically from the device tree. When IRQ resources are
specified the driver requires one IRQ resource per GPIO able to generate
an interrupt, and uses the translation table to compute the IRQ resource
offset instead of the IRQ number.
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove the manually specified ranges from PFC SoC data and compute the
ranges automatically. This prevents ranges from being out-of-sync with
pins definitions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The field contains the number of pins with an associated GPIO port. This
is currently equal to the total number of pins but will be modified when
adding support for pins without a GPIO port. Rename the field
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Add initial PFC support for the r8a7790 SoC.
At this point only GPIO interface is supported, move to
newer interfaces planned as incremental changes.
Original authors is Koji Matsuoka-san, thanks for him
and his team for the heavy lifting. Adjusted by Magnus
to work together with updated code in drivers/pinctrl.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@rms.renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial PFC support for the r8a73a4 SoC.
At this point only GPIO interface is supported, move to newer interfaces
planned as incremental changes.
Original authors are Morimoto-san with help from Yoshii-san, thanks to
them for the heavy lifting. Adjusted by Magnus to work together with
updated code in drivers/pinctrl.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The purpose of the dry-run is to ensure that a pin about to be
configured isn't in use. However, the current implementation is a no-op.
This proves that the dry-run isn't essential. Remove it.
Freeing configuration then becomes a no-op as well. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The sh_pfc_pin structure supplied in SoC data contains information about
pin configuration and name. It's abused to store GPIO data registers
information and pin config type. Move those fields out of the
pinmux_data_reg structure into the new sh_pfc_gpio_pin and
sh_pfc_pin_config structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All data registers are located in the same memory resource. Locate the
mapped resource at initializat time and use it directly instead of
computing a mapped address for each register. This gets rid of the
mapped_reg field of the pinmux_data_reg structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Move the sh_pfc_setup_data_regs(), sh_pfc_setup_data_reg(),
sh_pfc_get_data_reg(), sh_pfc_read_bit() and sh_pfc_write_bit()
function to gpio.c as they belong to the GPIO implementation. Inline
sh_pfc_read_bit() and sh_pfc_write_bit() in their only call location.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The PFC driver assumes that the value of the GPIO_PORTxxx enumeration
names are equal to the port number. This isn't true when the port number
space is sparse, as with the SH73A0.
Fix the issue by adding support for pin numbers ranges specified through
SoC data. When no range is specified the driver considers that the PFC
implements a single contiguous range for all pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The function is guaranteed to be called with a gpio number smaller than
nr_pins. The condition can the be simplified, and the function inlined.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The PFC core exposes a sh_pfc_config_gpio() function that configures
pinmuxing for a given GPIO (either a real GPIO or a function GPIO).
Handling of real and function GPIOs belong to the GPIO layer, move the
GPIO number to mark translation to the caller and rename the function to
sh_pfc_config_mux().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Instead of converting the GPIO number to an enum_id and looking up IRQ
table entries by enum_id, replace the pinmux_irq enum_ids field with a
gpios field and lookup entries using the GPIO number.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
As a step towards GPIO function removal, shorten the GPIO range
registered with the pinctrl core. Function GPIOs are now handled in the
GPIO handlers directly instead of going through the pinctrl API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Pinmux information should be provided by the pinmux driver, not arch
code. Make it possible to do so by supporting pinmux information passed
through the driver_data field in the platform ID table. Platform data
will remain supported until all arch code has been converted.
Rename the sh_pfc_platform_data structure to sh_pfc_soc_info to reflect
this.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
