The ISI is only present on the at91sam9g25, move the definition to the
at91sam9g25ek board dts to avoid warnings.
Solves the following warning for other 9x5ek boards:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
On at91sam9x5ek/at91sam9m10g45ek/sama5d3xek boards, we use the parallel
connection for ov2640. So we must set the hsync/vsync property (1 means
active high).
Otherwise, the connection would be seen as BT.656 or BT.1120.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the camera sensor ov2640 dt support. And connect sensor to isi node
as well.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
There is an external resistor divider on PB16, acting like a pull-down,
the pull-up increase power consumption and prevent the vbus detect pin
to reach Vss voltage, ~1.5V mesured on my board, it might not even work
if the pull-up is stronger than usual.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on various
platforms as support gets added. Some of the bigger changes are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for 4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1GuI
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
The sam9x5ek board has 2 jacks:
headphone wired on RHPOUT/LHPOUT of the wm8731
line in wired on LLINEIN/RLINEIN of the wm8731
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable the SSC needed for the WM8731 codec
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The WM8731 codec on sam9x5ek board is on i2c, address 1A
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Device Tree "num-ports" property of USB host node has to be
set to maximum number of ports available.
The possibility to activate a particular port is done by specifying the proper
gpio configuration for its vbus.
This patch fixes the USB host node by configuring the 3 ports available on the
product and letting "port A" available for USB gadget usage.
Reported-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Bo Shen <voice.shen@atmel.com>
to prepare the switch to the macro.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Device-tree updates for 3.10. The bulk of the churn in this branch is due
to i.MX moving from C-defined pin control over to device tree, which is
a one-time conversion that will allow greater flexibility down the road.
Besides that, there's PCI-e bindings for Marvell mvebu platforms and a
handful of cleanups to tegra due to the new include file functionality
of the device tree compiler.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8X1b
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree updates from Olof Johansson:
"Part 1 of device-tree updates for 3.10. The bulk of the churn in this
branch is due to i.MX moving from C-defined pin control over to device
tree, which is a one-time conversion that will allow greater
flexibility down the road.
Besides that, there's PCI-e bindings for Marvell mvebu platforms and a
handful of cleanups to tegra due to the new include file functionality
of the device tree compiler"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (113 commits)
arm: mvebu: PCIe Device Tree informations for Armada XP GP
arm: mvebu: PCIe Device Tree informations for Armada 370 DB
arm: mvebu: PCIe Device Tree informations for Armada 370 Mirabox
arm: mvebu: PCIe Device Tree informations for Armada XP DB
arm: mvebu: PCIe Device Tree informations for OpenBlocks AX3-4
arm: mvebu: add PCIe Device Tree informations for Armada XP
arm: mvebu: add PCIe Device Tree informations for Armada 370
ARM: sunxi: unify osc24M_fixed and osc24M
arm: vt8500: Add SDHC support to WM8505 DT
ARM: dts: Add a 64 bits version of the skeleton device tree
ARM: mvebu: Add Device Bus and CFI flash memory support to defconfig
ARM: mvebu: Add support for NOR flash device on Openblocks AX3 board
ARM: mvebu: Add support for NOR flash device on Armada XP-GP board
ARM: mvebu: Add Device Bus support for Armada 370/XP SoC
ARM: dts: imx6dl-wandboard: Add USB Host support
ARM: dts: imx51 cpu node
ARM: dts: Add missing imx27-phytec-phycore dtb target
ARM: dts: Add NFC support for i.MX27 Phytec PCM038 module
ARM: i.MX51: Add PATA support
ARM: dts: Add initial support for Wandboard Dual-Lite
...
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
[wenyou.yang@atmel.com: added spi nodes for the sam9263ek, sam9g20ek, sam9m10g45ek and sam9n12ek boards]
[wenyou.yang@atmel.com: submit the patch]
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Macb0 node cannot be activated in generic sam9x5ek.dtsi file
as the sam9g15 does not have one.
Move the macb0 & macb1 activation in board .dts file that
support them.
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
On at91sam9x5ek, macb0 is enabled, so it conflicts with i2c2 (PB4)
same for i2c1, (conflicts with LCD).
Moreover, only i2c0 is used on this board.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Set the dbgu pinctrl config by default as we have only one possible config
For other uart set the rxd/txd by default.
For at91sam9x5ek create soc based dts as we need to include specific soc dtsi.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
