Now that we've finally gotten rid of the non-atomic MST users leftover in
the kernel, we can finally get rid of all of the legacy payload code we
have and move as much as possible into the MST atomic state structs. The
main purpose of this is to make the MST code a lot less confusing to work
on, as there's a lot of duplicated logic that doesn't really need to be
here. As well, this should make introducing features like fallback link
retraining and DSC support far easier.
Since the old payload code was pretty gnarly and there's a Lot of changes
here, I expect this might be a bit difficult to review. So to make things
as easy as possible for reviewers, I'll sum up how both the old and new
code worked here (it took me a while to figure this out too!).
The old MST code basically worked by maintaining two different payload
tables - proposed_vcpis, and payloads. proposed_vcpis would hold the
modified payload we wanted to push to the topology, while payloads held the
payload table that was currently programmed in hardware. Modifications to
proposed_vcpis would be handled through drm_dp_allocate_vcpi(),
drm_dp_mst_deallocate_vcpi(), and drm_dp_mst_reset_vcpi_slots(). Then, they
would be pushed via drm_dp_mst_update_payload_step1() and
drm_dp_mst_update_payload_step2().
Furthermore, it's important to note how adding and removing VC payloads
actually worked with drm_dp_mst_update_payload_step1(). When a VC payload
is removed from the VC table, all VC payloads which come after the removed
VC payload's slots must have their time slots shifted towards the start of
the table. The old code handles this by looping through the entire payload
table and recomputing the start slot for every payload in the topology from
scratch. While very much overkill, this ends up doing the right thing
because we always order the VCPIs for payloads from first to last starting
timeslot.
It's important to also note that drm_dp_mst_update_payload_step2() isn't
actually limited to updating a single payload - the driver can use it to
queue up multiple payload changes so that as many of them can be sent as
possible before waiting for the ACT. This is -technically- not against
spec, but as Wayne Lin has pointed out it's not consistently implemented
correctly in hubs - so it might as well be.
drm_dp_mst_update_payload_step2() is pretty self explanatory and basically
the same between the old and new code, save for the fact we don't have a
second step for deleting payloads anymore -and thus rename it to
drm_dp_mst_add_payload_step2().
The new payload code stores all of the current payload info within the MST
atomic state and computes as much of the state as possible ahead of time.
This has the one exception of the starting timeslots for payloads, which
can't be determined at atomic check time since the starting time slots will
vary depending on what order CRTCs are enabled in the atomic state - which
varies from driver to driver. These are still stored in the atomic MST
state, but are only copied from the old MST state during atomic commit
time. Likewise, this is when new start slots are determined.
Adding/removing payloads now works much more closely to how things are
described in the spec. When we delete a payload, we loop through the
current list of payloads and update the start slots for any payloads whose
time slots came after the payload we just deleted. Determining the starting
time slots for new payloads being added is done by simply keeping track of
where the end of the VC table is in
drm_dp_mst_topology_mgr->next_start_slot. Additionally, it's worth noting
that we no longer have a single update_payload() function. Instead, we now
have drm_dp_mst_add_payload_step1|2() and drm_dp_mst_remove_payload(). As
such, it's now left it up to the driver to figure out when to add or remove
payloads. The driver already knows when it's disabling/enabling CRTCs, so
it also already knows when payloads should be added or removed.
Changes since v1:
* Refactor around all of the completely dead code changes that are
happening in amdgpu for some reason when they really shouldn't even be
there in the first place… :\
* Remove mention of sending one ACT per series of payload updates. As Wayne
Lin pointed out, there are apparently hubs on the market that don't work
correctly with this scheme and require a separate ACT per payload update.
* Fix accidental drop of mst_mgr.lock - Wayne Lin
* Remove mentions of allowing multiple ACT updates per payload change,
mention that this is a result of vendors not consistently supporting this
part of the spec and requiring a unique ACT for each payload change.
* Get rid of reference to drm_dp_mst_port in DC - turns out I just got
myself confused by DC and we don't actually need this.
Changes since v2:
* Get rid of fix for not sending payload deallocations if ddps=0 and just
go back to wayne's fix
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-18-lyude@redhat.com
VCPI is only sort of the correct term here, originally the majority of this
code simply referred to timeslots vaguely as "slots" - and since I started
working on it and adding atomic functionality, the name "VCPI slots" has
been used to represent time slots.
Now that we actually have consistent access to the DisplayPort spec thanks
to VESA, I now know this isn't actually the proper term - as the
specification refers to these as time slots.
Since we're trying to make this code as easy to figure out as possible,
let's take this opportunity to correct this nomenclature and call them by
their proper name - timeslots. Likewise, we rename various functions
appropriately, along with replacing references in the kernel documentation
and various debugging messages.
It's important to note that this patch series leaves the legacy MST code
untouched for the most part, which is fine since we'll be removing it soon
anyhow. There should be no functional changes in this series.
v2:
* Add note that Wayne Lin from AMD suggested regarding slots being between
the source DP Tx and the immediate downstream DP Rx
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-5-lyude@redhat.com
128b/132b supports using 64 slots starting from 0, while 8b/10b reserves
slot 0 for metadata.
Commit d6c6a76f80 ("drm: Update MST First Link Slot Information Based
on Encoding Format") added support for updating the topology state
accordingly, and commit 41724ea273 ("drm/amd/display: Add DP 2.0 MST
DM Support") started using it in the amd driver.
This feels more than a little cumbersome, especially updating the
information in atomic check. For i915, add the update to MST connector
.compute_config hook rather than iterating over all MST managers and
connectors in global mode config .atomic_check. Fingers crossed.
v3:
- Propagate errors from intel_dp_mst_update_slots() (Ville)
v2:
- Update in .compute_config() not .atomic_check (Ville)
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220208152317.3019070-1-jani.nikula@intel.com
Make things a bit more explicit by splitting
intel_cpu_transcoder_set_m_n() into separate variants for M1/N1 vs.
M2/N2. Makes the DRRS M/N programming at least more obvious.
Note that for the MST and DRRS cases we don't need to call the
M2/N2 variant at all since the transcoders that support those
do not have the M2/N2 registers.
Same could be said for i9xx_crtc_enable() but I want to do a
higher level code sharing between that valleyview_crtc_enable()
later in which case we do need the M2/N2 variant. This is also
why I keep the transcoder_has_m2_n2() in intel_cpu_transcoder_set_m2_n2()
so the caller doesn't have necessarily care what the chosen
transcoder supports.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Disabling planes in the middle of the modeset seuqnece does not make
sense since userspace can anyway disable planes before the modeset
even starts. So when the modeset seuqence starts the set of enabled
planes is entirely arbitrary. Trying to sprinkle the plane disabling
into the modeset sequence just means more randomness and potential
for hard to reproduce bugs.
So it makes most sense to just disable all planes first so that the
rest of the modeset sequence remains identical regardless of which
planes happen to be enabled by userspace at the time.
This reverts commit 84030adb9e.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
8b/10b encoding format requires to reserve the first slot for
recording metadata. Real data transmission starts from the second slot,
with a total of available 63 slots available.
In 128b/132b encoding format, metadata is transmitted separately
in LLCP packet before MTP. Real data transmission starts from
the first slot, with a total of 64 slots available.
v2:
* Move total/start slots to mst_state, and copy it to mst_mgr in
atomic_check
v3:
* Only keep the slot info on the mst_state
* add a start_slot parameter to the payload function, to facilitate non
atomic drivers (this is a temporary workaround and should be removed when
we are moving out the non atomic driver helpers)
v4:
*fixed typo and formatting
v5: (no functional changes)
* Fixed formatting in drm_dp_mst_update_slots()
* Reference mst_state instead of mst_state->mgr for debugging info
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
[v5 nitpicks]
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025223825.301703-3-lyude@redhat.com
If we want to return from for_each_intel_connector_iter(), one
way is calling drm_connector_list_iter_end() before returning
to avoid memleak. The other way is just breaking from the bracket
and then returning after the outside drm_connector_list_iter_end().
Obviously, the second way makes code smaller and more clear.
Apply it to the function intel_dp_mst_atomic_master_trans_check().
Signed-off-by: He Ying <heying24@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022022243.138860-1-heying24@huawei.com
PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder.
Bigjoiner is making life even more confusing by introducing
a N:1 relationship between pipes and transcoders. In that case
we only enable/configure the transcoder corresponding to the
master pipe. Let's do some renames to make it clear we're dealing
with the transcoder rather than pipe when it comes to
PIPECONF/TRANSCONF.
I decided to leave the _cpu_ part out from the function/macro
names since the PCH transcoder related stuff already has a
_pch_ in their name. So shouldn't be possible to confuse them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
HDMI and DisplayPort sequences states that audio and PSR should be
disabled before planes are disabled.
Not following it did not caused any problems up to Alderlake-P but
for this platform it causes underruns during the PSR2 disable
sequence.
Specification don't mention that DRRS should be disabled before planes
but it looks safer to switch back to the default refresh rate before
following with the rest of the pipe disable sequence.
BSpec: 49191
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210726181559.80855-1-jose.souza@intel.com
A new step has been added to the DP modeset sequences for all platforms
with display version 12 and beyond: if enabling DP MST with FEC, we
need to set a chicken bit before enabling the transcoder. The chicken
bit should be disabled again before disabling the transcoder (which we
can do unconditionally since it shouldn't be set anyway in non-MST
cases).
Bspec: 49190, 54128, 55424
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723170618.1477415-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Bring drm-intel-next closer to drm-next and drm-intel-gt-next for a more
feasible baseline for topic branches.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[why]
Link rate in kHz is what is eventually required to calculate the link
bandwidth, which makes kHz a more generic unit. This should also make
forward-compatibility with new DP standards easier.
[how]
- Replace 'link rate DPCD code' with 'link rate in kHz' when used with
drm_dp_mst_topology_mgr_init()
- Add/remove related DPCD code conversion from/to kHz where applicable
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512210011.8425-2-nikola.cornij@amd.com
Core Changes:
- drm: Rename DP_PSR_SELECTIVE_UPDATE to better mach eDP spec (Jose).
Driver Changes:
- Display plane clock rates fixes and improvements (Ville).
- Uninint DMC FW loader state during shutdown (Imre).
- Convert snprintf to sysfs_emit (Xuezhi).
- Fix invalid access to ACPI _DSM objects (Takashi).
- A big refactor around how i915 addresses the graphics
and display IP versions. (Matt, Lucas).
- Backlight fix (Lyude).
- Display watermark and DBUF fixes (Ville).
- HDCP fix (Anshuman).
- Improve cases where display is not available (Jose).
- Defeature PSR2 for RKL and ALD-S (Jose).
- VLV DSI panel power fixes and improvements (Hans).
- display-12 workaround (Jose).
- Fix modesetting (Imre).
- Drop redundant address-of op before lttpr_common_caps array (Imre).
- Fix compiler checks (Jose, Jason).
- GLK display fixes (Ville).
- Fix error code returns (Dan).
- eDP novel: back again to slow and wide link training everywhere (Kai-Heng).
- Abstract DMC FW path (Rodrigo).
- Preparation and changes for upcoming
XeLPD display IP (Jose, Matt, Ville, Juha-Pekka, Animesh).
- Fix comment typo in DSI code (zuoqilin).
- Simplify CCS and UV plane alignment handling (Imre).
- PSR Fixes on TGL (Gwan-gyeong, Jose).
- Add intel_dp_hdcp.h and rename init (Jani).
- Move crtc and dpll declarations around (Jani).
- Fix pre-skl DP AUX precharge length (Ville).
- Remove stray newlines from random files (Ville).
- crtc->index and intel_crtc+drm_crtc pointer clean-up (Ville).
- Add frontbuffer tracking tracepoints (Ville).
- ADL-S PCI ID updates (Anand).
- Use unique backlight device names (Jani).
- A few clean-ups on i915/audio (Jani).
- Use intel_framebuffer instead of drm one on intel_fb functions (Imre).
- Add the missing MC CCS/XYUV8888 format support on display >= 12 (Imre).
- Nuke display error state (Ville).
- ADL-P initial enablement patches
starting to land (Clint, Imre, Jose, Umesh, Vandita, Mika).
- Display clean-up around VBT and the strap bits (Lucas).
- Try YCbCr420 color when RGB fails (Werner).
- More PSR fixes and improvements (Jose).
- Other generic display code clean-up (Jose, Ville).
- Use correct downstream caps for check Src-Ctl mode for PCON (Ankit).
- Disable HiZ Raw Stall Optimization on broken gen7 (Simon).
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YKVioeu0JkUAlR7y@intel.com
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
[why]
DP 1.4a spec mandates that if DP_EXTENDED_RECEIVER_CAP_FIELD_PRESENT is
set, Extended Base Receiver Capability DPCD space must be used. Without
doing that, the three DPCD values that differ will be wrong, leading to
incorrect or limited functionality. MST link rate, for example, could
have a lower value. Also, Synaptics quirk wouldn't work out well when
Extended DPCD was not read, resulting in no DSC for such hubs.
[how]
Modify MST topology manager to use the values from Extended DPCD where
applicable.
To prevent regression on the sources that have a lower maximum link rate
capability than MAX_LINK_RATE from Extended DPCD, have the drivers
supply maximum lane count and rate at initialization time.
This also reverts commit 2dcab875e7 ("Revert drm/dp_mst: Retrieve
extended DPCD caps for topology manager"), brining the change back to the
original commit ad44c03208 ("drm/dp_mst: Retrieve extended DPCD caps for
topology manager").
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210429221151.22020-2-nikola.cornij@amd.com
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
Atm the driver will calculate a wrong MST timeslots/MTP (aka time unit)
value for MST streams if the link parameters (link rate or lane count)
are limited in a way independent of the sink capabilities (reported by
DPCD).
One example of such a limitation is when a MUX between the sink and
source connects only a limited number of lanes to the display and
connects the rest of the lanes to other peripherals (USB).
Another issue is that atm MST core calculates the divider based on the
backwards compatible DPCD (at address 0x0000) vs. the extended
capability info (at address 0x2200). This can result in leaving some
part of the MST BW unused (For instance in case of the WD19TB dock).
Fix the above two issues by calculating the PBN divider value based on
the rate and lane count link parameters that the driver uses for all
other computation.
Bugzilla: https://gitlab.freedesktop.org/drm/intel/-/issues/2977
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125173636.1733812-2-imre.deak@intel.com
This reverts commit 0883ce8146. Originally
these quirks were added because of the issues with using the eDP
backlight interfaces on certain laptop panels, which made it impossible
to properly probe for DPCD backlight support without having a whitelist
for panels that we know have working VESA backlight control interfaces
over DPCD. As well, it should be noted it was impossible to use the
normal sink OUI for recognizing these panels as none of them actually
filled out their OUIs, hence needing to resort to checking EDIDs.
At the time we weren't really sure why certain panels had issues with
DPCD backlight controls, but we eventually figured out that there was a
second interface that these problematic laptop panels actually did work
with and advertise properly: Intel's proprietary backlight interface for
HDR panels. So far the testing we've done hasn't brought any panels to
light that advertise this interface and don't support it properly, which
means we finally have a real solution to this problem.
As a result, we now have no need for the force DPCD backlight quirk, and
furthermore this also removes the need for any kind of EDID quirk
checking in DRM. So, let's just revert it for now since we were the only
driver using this.
v3:
* Rebase
v2:
* Fix indenting error picked up by checkpatch in
intel_edp_init_connector()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114221709.2261452-6-lyude@redhat.com
Small changes to intel_dp_mode_valid(), allow listing modes that
can only be supported in the bigjoiner configuration, which is
not supported yet.
v13:
* Allow bigjoiner if hdisplay >5120
v12:
* slice_count logic simplify (Ville)
* Fix unnecessary changes in downstream_mode_valid (Ville)
v11:
* Make intel_dp_can_bigjoiner non static
so it can be used in intel_display (Manasi)
v10:
* Simplify logic (Ville)
* Allow bigjoiner on edp (Ville)
v9:
* Restric Bigjoiner on PORT A (Ville)
v8:
* use source dotclock for max dotclock (Manasi)
v7:
* Add can_bigjoiner() helper (Ville)
* Pass bigjoiner to plane_size validation (Ville)
v6:
* Rebase after dp_downstream mode valid changes (Manasi)
v5:
* Increase max plane width to support 8K with bigjoiner (Maarten)
v4:
* Rebase (Manasi)
Changes since v1:
- Disallow bigjoiner on eDP.
Changes since v2:
- Rename intel_dp_downstream_max_dotclock to intel_dp_max_dotclock,
and split off the downstream and source checking to its own function.
(Ville)
v3:
* Rebase (Manasi)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[vsyrjala:
* Keep bigjoiner disabled until everything is ready
* Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-3-manasi.d.navare@intel.com
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Since the display hardware is all there even when INTEL_DISPLAY_ENABLED
return false we have to be capable of shutting it down cleanly so
as to not anger the hw. To that end let's reduce the effect of
!INTEL_DISPLAY_ENABLE to just treating all outputs as disconnected.
Should prevent anyone from automagically enabling any of them, while
still allowing us to cleanly shut them down.
v2: Put the check into the right place for CRT
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910164256.25983-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
