The DP PHY vswing/pre-emphasis level programming the driver does is
related to the DPTX -> first LTTPR link segment only. Accordingly it
should be only programmed when link training the first LTTPR and kept
as-is when training subsequent LTTPRs and the DPRX. For these latter
PHYs the vs/pe levels will be set in response to writing the
DP_TRAINING_LANEx_SET_PHY_REPEATERy DPCD registers (by an upstream LTTPR
TX PHY snooping this write access of its downstream LTTPR/DPRX RX PHY).
The above is also described in DP Standard v2.0 under 3.6.6.1.
While at it simplify and add the LTTPR that is link trained to the debug
message in intel_dp_set_signal_levels().
Fixes: b30edfd8d0 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201229172201.4155327-2-imre.deak@intel.com
We need a power_domain wakeref in pps_{lock,unlock} to prevent
a race while resetting pps state in intel_power_sequencer_reset().
intel_power_sequencer_reset() need a pps_mutex to access pps_pipe
but it can't grab pps_mutex due to deadlock with power_well
functions are called while holding pps_mutex.
intel_power_sequencer_reset() is called by power_well function
associated with legacy platforms like vlv and chv therefore re-use
the POWER_DOMAIN_DISPLAY_CORE power domain, which only used
by vlv and chv display power domain.
This will avoids the unnecessary noise of unrelated power wells
in pps_{lock,unlock}.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107112500.16216-1-anshuman.gupta@intel.com
Add support for DP-HDMI2.1 PCON
From the series cover letter:
This patch series attempts to add support for a DP-HDMI2.1 Protocol
Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
E5 to DisplayPort_v2.0:
https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
The details are mentioned in:
VESA DP-to-HDMI PCON Specification Standalone Document
https://groups.vesa.org/wg/DP/document/15651
This series starts with adding support for FRL (Fixed Rate Link)
Training between the PCON and HDMI2.1 sink.
As per HDMI2.1 specification, a new data-channel or lane is added in
FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
lanes).
With these patches, the HDMI2.1 PCON can be configured to achieve FRL
training based on the maximum FRL rate supported by the panel, source
and the PCON.
The approach is to add the support for FRL training between PCON and
HDMI2.1 sink and gradually add other blocks for supporting higher
resolutions and other HDMI2.1 features, that can be supported by pcon
for the sources that do not natively support HDMI2.1.
This is done before the DP Link training between the source and PCON
is started. In case of FRL training is not achieved, the PCON will
work in the regular TMDS mode, without HDMI2.1 feature support.
Any interruption in FRL training between the PCON and HDMI2.1 sink is
notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
registers are read and FRL training is re-attempted.
Currently, we have tested the FRL training and are able to enable 4K
display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
panel.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lfdpndkt.fsf@intel.com
Since we're about to start adding support for Intel's magic HDR
backlight interface over DPCD, we need to ensure we're properly
programming this field so that Intel specific sink services are exposed.
Otherwise, 0x300-0x3ff will just read zeroes.
We also take care not to reprogram the source OUI if it already matches
what we expect. This is just to be careful so that we don't accidentally
take the panel out of any backlight control modes we found it in.
v2:
* Add careful parameter to intel_edp_init_source_oui() to avoid
re-writing the source OUI if it's already been set during driver
initialization
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-2-lyude@redhat.com
If PCON has capability to convert RGB->YCbCr colorspace and also
to 444->420 downsampling then for any YUV420 only mode, we can
let the PCON do all the conversion. If the PCON supports
RGB->YCbCr conversion for all BT2020, BT709, BT601, choose
the one that is selected by userspace via connector colorspace
property, otherwise default to BT601.
v2: As suggested by Uma Shankar, considered case for colorspace
BT709 and BT2020, and default to BT601. Also appended dir
'display' in commit message.
v3: Fixed typo in condition for printing one of the error msg.
v4: As suggested by Uma Shankar:
-Fixed bug in determining the colorspace for RGB->YCbCr conversion.
-Fixed minor formatting issues
Also updated the commit message as per latest changes.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-16-ankit.k.nautiyal@intel.com
When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink
via DP HDMI2.1 PCON, the PCON can be configured to decode the
DSC1.1 compressed stream and encode to DSC1.2. It then sends the
DSC1.2 compressed stream to the HDMI2.1 sink.
This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based
on the PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder
capabilities.
v2: Addressed review comments from Uma Shankar:
-fixed the error in packing pps parameter values
-added check for pcon in the pcon related function
-appended display in commit message
v3: Only consider non-zero DSC FRL b/w for determining max FRL b/w
supported by sink.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch BRACES, LINE_SPACING, PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-15-ankit.k.nautiyal@intel.com
This patch adds support to read and store the DSC capabilities of the
HDMI2.1 PCon encoder. It also adds a new field to store these caps,
The caps are read during dfp update and can later be used to get the
PPS parameters for PCON-HDMI2.1 sink pair. Which inturn will be used
to take a call to override the existing PPS-metadata, by either
writing the entire new PPS metadata, or by writing only the
PPS override parameters.
v2: Restructured the code to read all capability DPCDs at once and store
in an array in intel_dp structure.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-13-ankit.k.nautiyal@intel.com
In this patch enables support for detecting link failures between
PCON and HDMI sink in i915 driver. HDMI link loss indication to
upstream DP source is indicated via IRQ_HPD. This is followed by
reading of HDMI link configuration status (HDMI_TX_LINK_ACTIVE_STATUS).
If the PCON → HDMI 2.1 link status is off; reinitiate frl link
training to recover. Also, report HDMI FRL link error count range for
each individual FRL active lane is indicated by
DOWNSTREAM_HDMI_ERROR_STATUS_LN registers.
v2: Checked for dpcd read and write failures and added debug message.
(Uma Shankar)
v3: Rearranged code to re-start FRL link training or fall back to
TMDS mode.
v4: Resused function to check frl which inturn restarts FRL and
fallback to TMDS mode.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-12-ankit.k.nautiyal@intel.com
This patch adds functions to start FRL training for an HDMI2.1 sink,
connected via a PCON as a DP branch device.
This patch also adds a new structure for storing frl training related
data, when FRL training is completed.
v2: As suggested by Uma Shankar:
-renamed couple of variables for better clarity
-tweaked the macros used for correct semantics for true/false
-fixed other styling issues.
v3: Completed the TODO for condition for going to FRL mode.
Modified the condition to determine the required FRL b/w
based only on the Pcon and Sink's max FRL values.
Moved the frl structure initialization to intel_dp_init_connector().
v4: Fixed typo in initialization of frl structure.
v5: Always use FRL if its possible, instead of enabling only for
higher modes as done in v3.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
[Jani: Fixed checkpatch BRACES, CONSTANT_COMPARISON.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-10-ankit.k.nautiyal@intel.com
HDMI2.1 PCON advertises Max FRL bandwidth supported by the PCON.
This patch captures this in dfp cap structure in intel_dp and uses
this to prune connector modes that cannot be supported by the PCON
and FRL bandwidth.
v2: Addressed review comments from Uma Shankar:
-tweaked the comparison of target bw and pcon frl bw to avoid roundup errors.
-minor modification of field names and comments.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-9-ankit.k.nautiyal@intel.com
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
This patch fixes the slice count computation algorithm
for calculating the slice count based on Peak pixel rate
and the max slice width allowed on the DSC engines.
We need to ensure slice count > min slice count req
as per DP spec based on peak pixel rate and that it is
greater than min slice count based on the max slice width
advertised by DPCD. So use max of these two.
In the prev patch we were using min of these 2 causing it
to violate the max slice width limitation causing a blank
screen on 8K@60.
Fixes: d9218c8f6c ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204205804.25225-1-manasi.d.navare@intel.com
(cherry picked from commit d371d6ea92)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch fixes the slice count computation algorithm
for calculating the slice count based on Peak pixel rate
and the max slice width allowed on the DSC engines.
We need to ensure slice count > min slice count req
as per DP spec based on peak pixel rate and that it is
greater than min slice count based on the max slice width
advertised by DPCD. So use max of these two.
In the prev patch we were using min of these 2 causing it
to violate the max slice width limitation causing a blank
screen on 8K@60.
Fixes: d9218c8f6c ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204205804.25225-1-manasi.d.navare@intel.com
Enable HDMI Colorspace for LSPCON based devices. Sending Colorimetry
data for HDR using AVI infoframe. LSPCON firmware expects this and though
SOC drives DP, for HDMI panel AVI infoframe is sent to the LSPCON device
which transfers the same to HDMI sink.
v2: Dropped state managed in drm core as per Jani Nikula's suggestion.
v3: Aligned colorimetry handling for lspcon as per compute_avi_infoframes,
as suggested by Ville.
v4: Finally fixed this with Ville's help, re-phrased the commit header
and description.
v5: Register HDMI colorspace for lspcon and move this to
intel_dp_add_properties as we can't create property at late_register.
Credits-to: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-9-uma.shankar@intel.com
Attach HDR property for Gen9 devices with MCA LSPCON
chips.
v2: Cleaned HDR property attachment logic based on capability
as per Jani Nikula's suggestion.
v3: Fixed the HDR property attachment logic as per the new changes
by Kai-Feng to align with lspcon detection failure on some devices.
v4: Add HDR proprty in late_register to handle lspcon detection,
as suggested by Ville.
v5: Init Lspcon only if advertized from BIOS.
v6: Added a Todo to plan a cleanup later, added Ville's RB.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-4-uma.shankar@intel.com
When the clock is higher than the dotclock, try with 2 pipes enabled.
If we can enable 2, then we will go into big joiner mode, and steal
the adjacent crtc.
This only links the crtc's in software, no hardware or plane
programming is done yet. Blobs are also copied from the master's
crtc_state, so it doesn't depend at commit time on the other
crtc_state.
v6:
* Enable dSC for any mode->hdisplay > 5120
v5:
* Remove intel_dp_max_dotclock (Manasi)
v4:
* Fixes in intel_crtc_compute_config (Ville)
v3:
* Manual Rebase (Manasi)
Changes since v1:
- Rename pipe timings to transcoder timings, as they are now different.
Changes since v2:
- Rework bigjoiner checks; always disable slave when recalculating
master. No need to have a separate bigjoiner pass any more.
- Use pipe_mode instead of transcoder_mode, to clean up the code.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala:
* hskew isn't a thing
* Do the dsc compute if bigjoiner is enabled, not the other way around]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-4-manasi.d.navare@intel.com
Small changes to intel_dp_mode_valid(), allow listing modes that
can only be supported in the bigjoiner configuration, which is
not supported yet.
v13:
* Allow bigjoiner if hdisplay >5120
v12:
* slice_count logic simplify (Ville)
* Fix unnecessary changes in downstream_mode_valid (Ville)
v11:
* Make intel_dp_can_bigjoiner non static
so it can be used in intel_display (Manasi)
v10:
* Simplify logic (Ville)
* Allow bigjoiner on edp (Ville)
v9:
* Restric Bigjoiner on PORT A (Ville)
v8:
* use source dotclock for max dotclock (Manasi)
v7:
* Add can_bigjoiner() helper (Ville)
* Pass bigjoiner to plane_size validation (Ville)
v6:
* Rebase after dp_downstream mode valid changes (Manasi)
v5:
* Increase max plane width to support 8K with bigjoiner (Maarten)
v4:
* Rebase (Manasi)
Changes since v1:
- Disallow bigjoiner on eDP.
Changes since v2:
- Rename intel_dp_downstream_max_dotclock to intel_dp_max_dotclock,
and split off the downstream and source checking to its own function.
(Ville)
v3:
* Rebase (Manasi)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[vsyrjala:
* Keep bigjoiner disabled until everything is ready
* Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-3-manasi.d.navare@intel.com
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
intel_dp_ycbcr420_config() is rather pointless. Just inline it
directly into intel_dp_compute_config(). This gets rid of the
ugly double assignment of output_format.
Not really sure what the best policy would be when the user
supplies a mode classified by the display as "YCbCr 4:2:0
only", but we know that we can't do YCbCr 4:2:0 output. For
now keep the current behaviour of just silently upgrade
it to RGB 4:4:4.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-3-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Remove the lspcon special case from intel_dp_compute_config() and
just treat it like any other DFP than can do 4:4:4->4:2:0 conversion.
The only difference between the two codepaths was that the lspcon
code tried to already halve port_clock. That was just total nonsense
as we hadn't even computed the base port_clock at that time.
All that stuff happens intel_dp_compute_link_config*() and it
already takes care of the 4:2:0 clock reduction.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-2-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
The DP Standard's recommendation is to use the LTTPR non-transparent
mode link training if LTTPRs are detected, so let's do this.
Besides power-saving, the advantages of this are that the maximum number
of LTTPRs can only be used in non-transparent mode (the limit is 5-8 in
transparent mode), and it provides a way to narrow down the reason for a
link training failure to a given link segment. Non-transparent mode is
probably also the mode that was tested the most by the industry.
The changes in this patchset:
- Pass the DP PHY that is currently link trained to all LT helpers, so
that these can access the correct LTTPR/DPRX DPCD registers.
- During LT take into account the LTTPR common lane rate/count and the
per LTTPR-PHY vswing/pre-emph limits.
- Switch to LTTPR non-transparent LT mode and train each link segment
according to the sequence in DP Standard v2.0 (complete CR/EQ for
each segment before continuing with the next segment).
v2:
- Switch to non-transparent mode during connector detection, which is
required before reading the per-PHY LTTPR capabilities.
- Move the DP_PHY_LTTPR() macro to drm_dp_helper.h (Ville)
- Use the new drm_dp_dpcd_read_phy_link_status() instead of adding the
same logic to intel_dp_get_link_status(). (Ville)
- Make intel_dp_lttpr_phy_caps() return a pointer to the whole array
instead of a pointer to its first element. (Ville)
- Add the intel_dp_phy_is_downstream_of_source() helper. (Ville)
- Add a code comment about the disable->enable quirk of
non-transparent mode.
- Add the intel_dp_training_pattern_set_reg() helper.
- Fix checkpatch/sparse warns.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-7-imre.deak@intel.com
By default LTTPRs should be in transparent link training mode,
nevertheless in this patch we switch to this default mode explicitly.
The DP Standard recommends this, supposedly because an LTTPR may be left
in the non-transparent mode (by BIOS, previous kernel, or after reset
due to a firmware bug). I haven't seen this happening, but let's follow
the DP Standard.
v2:
- Add a code comment about the explicit disabling of non-transparent
mode.
v3:
- Move check to prevent initing LTTPRs on eDP to init_dp_lttpr_init().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-6-imre.deak@intel.com
Split the prepare, link training, fallback-handling steps into their own
functions for clarity and as a preparation for the upcoming LTTPR
changes.
While at it also:
- Unexport and inline intel_dp_set_idle_link_train(), which is used at a
single place.
- Add some documentation to functions that are exported or that can use
a better description about which part of the LT sequence they
implement.
v2: (Ville)
- Unexport/inline intel_dp_set_idle_link_train()
- Make the documentation of
intel_dp_prepare_link_train()/intel_dp_stop_link_train() more accurate
wrt. HW specific details.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-3-imre.deak@intel.com
An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.
Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.
v2:
- Use a helper instead of open-coding the masking. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-2-imre.deak@intel.com
Atm, if a full modeset is performed during the initial modeset the link
training will happen with uninitialized max DP rate and lane count. Make
sure the corresponding encoder state is initialized by adding an encoder
hook called during driver init and system resume.
A better alternative would be to store all states in the CRTC state and
make this state available for the link re-training code. Also instead of
the DPCD read in the hook there should be really a proper sink HW
readout in place. Both of these require a bigger rework, so for now opting
for this minimal fix to make at least full initial modesets work.
The patch is based on
https://patchwork.freedesktop.org/patch/101473/?series=10354&rev=3
v2: (Ville)
- s/sanitize_state/sync_state/
- No point in calling the hook when CRTC is disabled, remove the call.
- No point in calling the hook for MST, remove it.
v3: Check only DPCD_REV to avoid clobbering intel_dp->dpcd. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005230154.1477653-1-imre.deak@intel.com
