[WHY]
Logging for SMU response value after the wait allows us to know
immediately what the response value was. Makes it easier to debug should
the value be anything other than OK.
[HOW]
Using the the already available DC SMU logging functions.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
For VG, we want to turn off power/backlight of the intenral panel when
plugging in external monitor and going to "external monitor only" mode.
[how]
For turning off power of the internal panel, ignore the config flag whic
bypasses power sequencing for eDP panels.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Only on VG, if external display is disconnected during S3 suspend, the
internal panel doesn't light up on resume because we set the power state
using an unsupported DPCD register SET_POWER. To check the register is
supported, we need to check SET_POWER_CAPABLE first which is
eDP-specific DPCD register field.
[how]
Check the SET_POWER_CAPABLE register field and decide the control of the
eDP power state based on the read register value.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Agustin Gutierrez <Agustin.Gutierrez@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when connect one 4k@144hz dp to dsc mst hub, 4k@144hz mode is in valid
mode list. but some mst hub port output bandwidth does not support
4k@144hz.
[How]
add mst port output bandwidth checks, include full_pbn, branch max
throughput mps.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While updating the config of hdcp, we use the sink_singal type of the
dc_sink to decide the HDCP operation mode. However, it doesn't consider
the case when the sink is a emulated one.
[How]
Take dc_em_sink into account while updating HDCP config.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Observe that we have several problems while releasing remote dc_sink
under mst cases.
- When unplug mst branch device from the source, we now try to free all
remote dc_sinks in dm_helpers_dp_mst_stop_top_mgr(). However, there are
bugs while we're releasing dc_sinks here. First of all,
link->remote_sinks[] array get shuffled within
dc_link_remove_remote_sink(). As the result, increasing the array index
within the releasing loop is wrong. Secondly, it tries to call
dc_sink_release() to release the dc_sink of the same aconnector every
time in the loop. Which can't release dc_sink of all aconnector in the
mst topology.
- There is no code path for us to release remote dc_sink for disconnected
sst monitor which unplug event is notified by CSN sideband message. Which
means we'll use stale dc_sink data to represent later on connected
monitor. Also, has chance to break the maximum remote dc_sink number
constraint.
[How]
Distinguish unplug event of mst scenario into 2 cases.
* Unplug sst/legacy stream sink off the mst topology
- Release related remote dc_sink in detec_ctx().
* Unplug mst branch device off the mst topology
- Release related remote dc_sink in early_unregister()
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 3c4d55c9b9.
Revert the commit because:
- It's incomplete of the function dm_set_dpms_off() for mst case. For
stream sinks whithin the same mst topology, they share the same dc_link.
dm_set_dpms_off() tries to update one mst stream only which is
incomplete.
- Setting dpms off should be triggered by usermode. Besdies, it seems
usermode does release relevant resource for mst & non-mst case when
unplug connecotr now.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 035f54969b.
The reverted commit was trying to fix side effect brought by
commit 3c4d55c9b9 ("drm/amd/display: turn DPMS off on connector unplug")
However,
* This reverted commit will have mst case never call dm_set_dpms_off()
which conflicts the idea of original commit 3c4d55c9b9 ("drm/amd/display: turn DPMS off on connector unplug")
That's due to dm_crtc_state is always null since the input parameter
aconnector is the root device (source) of mst topology. It's not an
end stream sink within the mst topology.
* Setting dpms off should be triggered by usermode. Besdies, it seems
usermode does release relevant resource for mst & non-mst case when
unplug connecotr now. Which means we no longer need both commits now:
commit 3c4d55c9b9 ("drm/amd/display: turn DPMS off on connector unplug")
commit 035f54969b ("drm/amd/display: Add flag to detect dpms force off during HPD")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A variety of Lenovo machines with Rembrandt APUs and OLED panels have
stopped showing the display at login. This behavior clears up after
leaving it idle and moving the mouse or touching keyboard.
It was bisected to be caused by commit 559e265522 ("drm/amd/display:
keep eDP Vdd on when eDP stream is already enabled"). Revert this commit
to fix the issue.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2047
Reported-by: Aaron Ma <aaron.ma@canonical.com>
Fixes: 559e265522 ("drm/amd/display: keep eDP Vdd on when eDP stream is already enabled")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some APUs with SMU13 are showing the following message:
`amdgpu 0000:63:00.0: amdgpu: Unexpected and unhandled version: 3.1`
This warning isn't relevant for smu info 3.1, as no bootup information
is present in the table.
Fixes: 593a54f180 ("drm/amd/pm: correct the way for retrieving bootup clocks")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
set mp1 unload state will cause the SMC FW can't accept any SMU message,
skip to set mp1 unload state to avoid following case fail:
- runtime pm case.
- gpu reset case.
Fixes: 72aeb6ee0c ("drm/amd/pm: fix driver reload SMC firmware fail issue for smu13")
Signed-off-by: Yang Wang <KevinYang.Wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The EccInfo_t struct in driver_if.h is as below in official release
verion 68.55.0
typedef struct {
uint64_t mca_umc_status;
uint64_t mca_umc_addr;
uint16_t ce_count_lo_chip;
uint16_t ce_count_hi_chip;
uint32_t eccPadding;
uint64_t mca_ceumc_addr;
} EccInfo_t;
It's different from the debug version druing develop print correctable
error address, so adjust EccInfo_t struct.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Certain GL unit tests for large textures can cause problems
with the OOM killer since there is no way to link this memory
to a process. This was originally mitigated (but not necessarily
eliminated) by limiting the GTT size. The problem is this limit
is often too low for many modern games so just make the limit 1/2
of system memory. The OOM accounting needs to be addressed, but
we shouldn't prevent common 3D applications from being usable
just to potentially mitigate that corner case.
Set default GTT size to max(3G, 1/2 of system ram) by default.
v2: drop previous logic and default to 3/4 of ram
v3: default to half of ram to align with ttm
v4: fix spelling in comment (Kent)
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1942
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Loop through all VMIDs for gmc_v10_0_flush_gpu_tlb_pasid and
gmc_v11_0_flush_gpu_tlb_pasid (only if using MES for gmc_v10). This is
required for MES due to use_different_vmid_compute causing SDMA queues
to be assigned different VMIDs than compute for the same PASID.
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the same pattern as the DML Makefile and while we are here
add a missing x86 guard around the msse flags for DCN3.2.x.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit d8e4fb9112.
This is no longer necessary as newer patches require these functions
without CONFIG_DRM_AMD_DC_DCN.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1542:11:
warning: variable 'i' set but not used [-Wunused-but-set-variable]
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
enable_mes and enable_mes_kiq are set in both device init and
MES IP init. Leave the ones in MES IP init, since it is
a more accurate way to judge from GC IP version.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All displays need to be blanked during the uclk OC interface so that we can
guarantee pstate switching support. If the display config doesn't support
pstate switching, only using core_link_disable_stream will not enable it
as the front-end is untouched. We need to go through the full plane removal
sequence to properly program the pipe to allow pstate switching.
[How]
- guard clk_mgr functions with non-NULL checks
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The display driver on some OSes need to track it in order to
perform memory clock switching decisions.
[HOW]
Propagate the vrr active state to dirty bit so that on mode set it
disables dynamic memory clock switching.
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Harry VanZyllDeJong <harry.vanzylldejong@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Video Timing Extended Metadata packet (VTEM) is required for features
like VRR and FVA
[How]
Adding support for VTEM transmission to stream encoders in DCN20 and DCN30
as part of FVA support
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Ahmad Othman <ahmad.othman@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Currently there is no support for HF-VSIF
- The current support of VSIF is limited to H14b infoframe
[How]
- refactor VSIF
- Added new builder for HF-VSIF
- Added the HF-VSIF packet to DisplayTarget
- Updates DC to apply HF-VSIF updates when updating streams
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Ahmad Othman <ahmad.othman@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Memory clock switching has great potential for power savings.
[HOW]
The driver code was modified to notify the DMCUB firmware that it should
stretch the vertical blank of frames when a memory clock switch is about
to start so that no blackouts happen on the screen due to unavailability
of the frame buffer.
The driver logic to determine when such firmware assisted strategy can
be initiated is also implemented and consists on checking prerequisites
of the feature.
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Felipe Clark <felipe.clark@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- missing in dcn30 function
- Fix a divide by 0 when ACR trigger
[How]
- Add IS_SMU_TIMEOUT() to dcn30_smu_send_msg_with_param
- Add zero check in dcn20_update_clocks_update_dentist
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
