The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of
default uart pads) removed default uart pads that where getting populated
and which was making rx pin wakeup capable. If uart pads were used in
different mode by any other module then it would fail since the default
pads took over all the uart pins forcefully. With removal of default pads
the rx_pad wakeup for console uart while waking up from off mode is broken.
Utilise the mux api available to probe the availability of mux pins
in uart mode and probe for availability of uart pin in mux mode0
if uart is available as uart pin itself then configure rx pin
as wakeup capable.
This patch itself doesn't cater to all boards. Boards using uart rx wakeup
mechanism should ensure the usage of omap_serial_init_port by configuring
required uart ports and pass necessary mux data, till then this probing of
uart pins can cater to enabling of rx pad wakeup to most of the boards.
This patch can also throw some boot warning from _omap_mux_get_by_name
if pin is requested for availability is not present while dynamically probing
the uart pins availability such boot warnings can be addressed only when board
files are patched with omap_serial_init_port calls passing the right pads
needed for a given port.
Discussion Threads for reference:
http://www.spinics.net/lists/linux-omap/msg69859.htmlhttp://www.spinics.net/lists/linux-omap/msg68659.html
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russ Dill <russ.dill@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated to fix compile when CONFIG_OMAP_MUX is not set]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds minimal support for AM335X machine init.
During last merge window, two separate patches supporting am33xx
machine init had been submitted,
1. Link to earlier Baseport patch submission (Legacy):
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg59325.html
2. Link to earlier DT based machine init support patch submission:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg61398.html
And both had got accepted at that time, but got missed during
merge window.
But now, since we have taken decision to make am33xx as a separate
class and not to follow omap3 family, these patches needs to changes
accordingly (only changes),
- Combine both the patches, since early init and timer init
used in board-generic.c file requires them.
- Remove dependency on AM3517EVM, and only use DT approach
for machine init.
- Change the config option (as changed recently)
CONFIG_SOC_OMAPAM33XX --> CONFIG_SOC_AM33XX
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for low level debugging on AM335X EVM (AM33XX family).
Currently only support for UART1 console, which is used on AM335X EVM
is added.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3b511201 (ARM: OMAP: rx51: Platform support for lis3lv02d accelerometer)
added support for lis3lv02d accelerometer.
The patch was still using OMAP_GPIO_IRQ which no longer exists.
Fix it by using gpio_to_irq().
Signed-off-by: Tony Lindgren <tony@atomide.com>
The FS (Full Speed) USB controller is available on 2420 and 2430,
but not being used.
Out of the 2420 based boards only Nokia N8X0 are seeing active
development and they have external HS (High Speed) TUSB controller.
On omap 2430sdp there is MUSB HS controller, so there's no need
to use the legacy USB FS controller.
That leaves only H4 and Apollon boards that could use the FS USB
controller. As both H4 and Apollon boards are old proprietary
development boards, it's unlikely that we have any active
developers working on those boards using the USB.
So remove the FS USB support for omap2 machines. Patches are
welcome if somebody wants to instead fix it all up to the
current standards.
Cc: linux-usb@vger.kernel.org
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We should not select ARCH_OMAP_OTG as the hardware does not
have the legacy FS (Full Speed) USB interface.
Cc: linux-usb@vger.kernel.org
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It includes:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=tmIU
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
After a clean-up of the interfaces the OMAP Smartreflex IP driver is now a
generic driver. Move it to drivers/power/avs/.
The build is controlled by the following Kconfig options:
. CONFIG_POWER_AVS: general knob for Adaptive Voltage Scaling support,
. CONFIG_POWER_AVS_OMAP: AVS(Adaptive Voltage Scaling)
support on OMAP containing the version 1 or version 2 of the SmartReflex IP,
. CONFIG_POWER_AVS_OMAP_CLASS3: Class 3 implementation of Smartreflex.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add a Kconfig menu (POWER_AVS) and rename the Kconfig options
for the OMAP SmartReflex implementation:
CONFIG_OMAP_SMARTREFLEX renames to CONFIG_POWER_AVS_OMAP
CONFIG_OMAP_SMARTREFLEX_CLASS3 renames to CONFIG_POWER_AVS_OMAP_CLASS3
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the global errminlimit debugfs entry and create per-voltage
entries from the data tables.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The SmartReflex driver incorrectly treats some per-OPP data as data
common to all OPPs (e.g., ERRMINLIMIT). Move this data into a per-OPP
data structure.
Furthermore, in order to make the SmartReflex implementation ready for
the move to drivers/, remove the dependency from the SR driver code
to the voltage layer by querying the data tables only from the SR device
init code.
Based on Paul's original code for the SmartReflex driver conversion.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move the omap_volt_data structure from mach-omap2/ directory
to arch/arm/plat-omap/include/plat/ so that it is accessible
from both mach-omap2 and drivers directories.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Now that omap_test_timeout is only accessible from mach-omap2/,
introduce a similar function for SR.
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Change the name field value to better reflect the smartreflex
integration in the system.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Associate a name with each SmartReflex instance from the hwmod data,
rather than attempting to reuse the name of a voltage domain. The name
from hwmod better reflects the smartreflex integration in the system.
Also have the name passed to the drivers using pdata, which helps to remove
any dependencies on SoC-specific structures.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Convert SmartReflex "class" functions to take a struct omap_sr *, rather than
a struct voltagedomain *. SmartReflex code should be driver code and not
tightly coupled to OMAP subarchitecture-specific structures.
Based on Paul's original code for the SmartReflex driver conversion.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move the smartreflex header file
(arch/arm/mach-omap2/smartreflex.h) in a new header file
include/linux/power/smartreflex.h.
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=21h6
-----END PGP SIGNATURE-----
Merge tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
More cleanups, continuing an earlier set with omap and samsung specific
cleanups. These could not go into the first set because they have
dependencies on various other series that in turn depend on the first
cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7UKB
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cleanups (part 2) from Olof Johansson:
"More cleanups, continuing an earlier set with omap and samsung
specific cleanups. These could not go into the first set because they
have dependencies on various other series that in turn depend on the
first cleanups."
Fixed up conflicts in arch/arm/plat-omap/counter_32k.c due to commit
bd0493eaaf: "move read_{boot,persistent}_clock to the architecture
level" that changed how the persistent clocks were handled. And trivial
conflicts in arch/arm/mach-omap1/common.h due to just independent
changes close to each other.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: SAMSUNG: merge plat-s5p into plat-samsung
ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig
ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung
ARM: SAMSUNG: move platform device for s5p uart into plat-samsung
ARM: SAMSUNG: move hr timer for common s5p into plat-samsung
ARM: SAMSUNG: move pm part for common s5p into plat-samsung
ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung
ARM: SAMSUNG: move clock part for common s5p into plat-samsung
ARM: S3C24XX: Use common macro to define resources on dev-uart.c
ARM: S3C24XX: move common clock init into common.c
ARM: S3C24XX: move common power-management code to mach-s3c24xx
ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c
ARM: S3C24XX: move plat-s3c24xx/cpu.c
ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to SOC_AM33XX
ARM: OMAP2+: Kconfig: convert SOC_OMAPTI81XX to SOC_TI81XX
GPMC: add ECC control definitions
ARM: OMAP2+: dmtimer: remove redundant sysconfig context restore
ARM: OMAP: AM35xx: convert 3517 detection/flags to AM35xx
ARM: OMAP: AM35xx: remove redunant cpu_is checks for AM3505
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
...
Use the more generic SoC family soc_is_am35xx() instead of the specific
cpu_is_omap3517() (which is being removed.)
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Lots of gpio changes, both to core code and drivers. Changes do touch
architecture code to remove the need for separate arm/gpio.h includes
in most architectures. Some new drivers are added, and a number of
gpio drivers are converted to use irq_domains for gpio inputs used as
interrupts. Device tree support has been amended to allow multiple
gpio_chips to use the same device tree node. Remaining changes are
primarily bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=U6hj
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO driver changes from Grant Likely:
"Lots of gpio changes, both to core code and drivers.
Changes do touch architecture code to remove the need for separate
arm/gpio.h includes in most architectures.
Some new drivers are added, and a number of gpio drivers are converted
to use irq_domains for gpio inputs used as interrupts. Device tree
support has been amended to allow multiple gpio_chips to use the same
device tree node.
Remaining changes are primarily bug fixes."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (33 commits)
gpio/generic: initialize basic_mmio_gpio shadow variables properly
gpiolib: Remove 'const' from data argument of gpiochip_find()
gpio/rc5t583: add gpio driver for RICOH PMIC RC5T583
gpiolib: quiet gpiochip_add boot message noise
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
gpio/lpc32xx: Add device tree support
gpio: Adjust of_xlate API to support multiple GPIO chips
gpiolib: Implement devm_gpio_request_one()
gpio-mcp23s08: dbg_show: fix pullup configuration display
Add support for TCA6424A
gpio/omap: (re)fix wakeups on level-triggered GPIOs
gpio/omap: fix broken context restore for non-OFF mode transitions
gpio/omap: fix missing check in *_runtime_suspend()
gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()
gpio/omap: remove suspend/resume callbacks
gpio/omap: remove retrigger variable in gpio_irq_handler
gpio/omap: remove saved_wakeup field from struct gpio_bank
gpio/omap: remove suspend_wakeup field from struct gpio_bank
gpio/omap: remove saved_fallingdetect, saved_risingdetect
gpio/omap: remove virtual_irq_start variable
...
Conflicts:
drivers/gpio/gpio-samsung.c
Here's the big TTY/serial driver pull request for the 3.5-rc1 merge window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7rBoACgkQMUfUDdst+ykXsgCfeDKx6ZgLidYy3H40Y2Pt3XEO
TicAn1fcdGwOmMR/mowa+kTA68D/J6i2
=S7tG
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
While we generally attempt to get rid of board specific files and replace
them with device tree based descriptions, a lot of platforms have not
come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination of
DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wkmj
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc board specific changes from Olof Johansson:
"While we generally attempt to get rid of board specific files and
replace them with device tree based descriptions, a lot of platforms
have not come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination
of DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones."
Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: shmobile: fix smp build
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
ARM: pxa: Use REGULATOR_SUPPLY macro
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
...
Power management changes here are mostly for the omap platform, but also
include cpuidle changes for ux500 and suspend/resume code for mmp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oGcZ
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc power management changes from Olof Johansson:
"Power management changes here are mostly for the omap platform, but
also include cpuidle changes for ux500 and suspend/resume code for
mmp."
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
ARM: OMAP2+: dmtimer: cleanup iclk usage
ARM: OMAP4+: Add prm and cm base init function.
ARM: OMAP2/3: Add idle_st bits for ST_32KSYNC timer to prcm-common header
ARM: OMAP3: Fix CM register bit masks
ARM: OMAP: clock: convert AM3517/3505 detection/flags to AM35xx
ARM: OMAP3: clock data: treat all AM35x devices the same
...
The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game of
booting using device trees, which is a great step forward for them. at91
and spear have pretty much completed this process with a huge amount of
work being put into at91. The other platforms are continuing the process.
We finally start to see the payback on this investment, as new machines
are getting supported purely by adding a .dts source file that can be
completely independent of the kernel source.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7DYv
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.
We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."
Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
These bug fixes were not important enough to have them included in the
v3.4 release, mostly because they cover harmless warnings or unrealistic
configurations. Instead we queue them up to be picked up in the next
merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yCUM
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical arm-soc bug fixes from Olof Johansson:
"These bug fixes were not important enough to have them included in the
v3.4 release, mostly because they cover harmless warnings or
unrealistic configurations. Instead we queue them up to be picked up
in the next merge window."
Fixed up trivial conflict in arch/arm/mach-omap2/board-omap4panda.c
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: spear6xx: remove board selection options
ARM: OMAP: igep0020: Specify the VPLL2 regulator unconditionally
ARM: OMAP2+: INTC: fix Kconfig option for TI81XX
ARM: OMAP2+: remove incorrect irq_chip ack field
ARM: OMAP4: Adding ID for OMAP4460 ES1.1
ARM: OMAP4: panda: add statics to remove warnings
ARM: OMAP2+: Incorrect Register Offsets in OMAP Mailbox
ARM: OMAP: fix trivial warnings for dspbridge
arm: davinci: use for_each_set_bit_from
ARM: OMAP4: hsmmc: check for null pointer
ARM: OMAP1: fix compilation issue in board-sx1.c
ARM: disable SUSPEND/ARCH_SUSPEND_POSSIBLE for ARCH_TEGRA
ARM: davinci: da850-evm: fix section mismatch
ARM: tegra: add pll_x freq table entry for 750MHz
ARM: davinci: mark spi_board_info arguments as const
ARM: davinci: fix incorrect pdctl next bit position
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
* 'kirkwood_boards_for_v3.5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
Includes an update to v3.4-rc7
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds a simple BCH ecc computation api, similar to the
existing Hamming ecc api. It is intended to be used by the MTD layer.
It implements the following features:
- support 4-bit and 8-bit ecc computation
- do not protect user bytes in spare area, only data area is protected
- ecc for an erased NAND page (0xFFs) is also a sequence of 0xFFs
This last feature is obtained by adding a constant polynomial to
the hardware computed ecc. It allows to correct bitflips in blank pages
and is extremely useful to support filesystems such as UBIFS, which expect
erased pages to contain only 0xFFs.
This api has been tested on an OMAP3630 board.
Artem: The OMAP maintainer Tony Lindgren gave us his blessing for merging
this patch via the MTD tree.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Irq and clock names were wrong for dsp iommu configuration
for omap4.
- Renamed tesla_ick to dsp_fck:
This is required because the new naming convention introduced
by: commit 0e43327 "OMAP4 clock: Fix clock names and align
with hwmod names"
- Renamed INT_44XX_DSP_MMU to OMAP44XX_IRQ_TESLA_MMU.
Naming convention adopted since: commit e927f8d "omap4: Add
auto-generated irq and dma headers"
- dsp-iommu is enabled by default.
Signed-off-by: Juan Gutierrez <jgutierrez@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
The machine-specific omap2_mbox_startup is called only once
to initialize the whole mbox module, and as a result,
enabling the mbox irq at that point only works for the very first
mailbox instance opened.
Instead, this patch makes sure enable_irq() is called every
time a new mbox instance is opened. In addition, we're now
enabling the mbox's irq only after its notifier_block is registered,
to avoid possible race of receiving an interrupt without invoking
the user's notifier callback.
Signed-off-by: Juan Gutierrez <jgutierrez@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
[ohad@wizery.com: slightly reworded the commit log]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Add register offsets for GPIO_IRQSTATUS_RAW_0, GPIO_IRQSTATUS_RAW_0
which are present on OMAP4+ processors. Now we can distinguish
conditions applicable to OMAP4,5 and those specific to OMAP24xx
and OMAP3xxx.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The Chip Identification register on the am35x family of SoCs
has bits 12, 7:5, and 3:2 marked as reserved and are read as
zeroes. Unfortunately, on other omap SoCs, a 0 bit means a
feature is "Full Use" so the OMAP3_CHECK_FEATURE() macro
called by omap3_check_features() will incorrectly interpret
those zeroes to mean that a feature is present even though it
isn't. To fix that, the feature bits that are incorrectly
set (namely, OMAP3_HAS_IVA and OMAP3_HAS_ISP) need to be
cleared after all of the calls to OMAP3_CHECK_FEATURE() in
omap3_check_features() are made.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[khilman@ti.com: use soc_is_am35xx() instead of cpu_is_am35xx()]
Signed-off-by: Kevin Hilman <khilman@ti.com>
By default, request_irq() will auto-enable the requested IRQ.
For PRCM interrupts, we may want to avoid that until the PM core code
is fully ready to handle the interrupts. This is particularily true
for IO pad interrupts on OMAP3, which are shared between the hwmod
core and the PRM core.
In order to avoid PRCM IO-chain interrupts until the PM core is ready
to handle them, ready, set the IRQ_NOAUTOEN flag for the PRCM IO-chain
interrupt, which means it will remain disabled after request_irq().
Then, explicitly enable the PRCM interrupts after the request_irq() in
the PM core (but not in the hwmod core.)
Special thanks to Tero Kristo for suggesting to isolate the fix to
only the IO-chain interrupt on OMAP3 instead of all PRCM interrupts.
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Without an ->irq_set_wake() method in an irq_chip, calls to
enable_irq_wake() will fail. This also causes these interrupts to not
be able to abort suspend (via check_wakeup_irqs() in late suspend.)
Currently, we don't implement ->irq_set_wake() for INTC interrupts
because they default to be wakeup enabled by setting the GRPSEL bits
in PM init. Even though there is no ->irq_set_wake(), we want
enable_irq_wake() to succeed so these interrupts can abort suspend
when necessary.
To fix, set IRQCHIP_SKIP_SET_WAKE flag for all the INTC
interrupts which avoids trying to check irq_chip->irq_set_wake()
and failing when it doesn't exist.
Longer term, we need to implement ->irq_set_wake() for the INTC
which can manage the appropriate GRPSEL bits.
Signed-off-by: NeilBrown <neilb@suse.de>
[khilman@ti.com: rework changelog]
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently the higher level omapdss platform driver gets the list of
displays in its platform data, and uses that list to create the
omap_dss_device for each display.
With DT, the logical way to do the above is to list the displays under
each individual output, i.e. we'd have "dpi" node, under which we would
have the display that uses DPI. In other words, each output driver
handles the displays that use that particular output.
To make the current code ready for DT, this patch modifies the output
drivers so that each of them creates the display devices which use that
output. However, instead of changing the platform data to suit this
method, each output driver is passed the full list of displays, and the
drivers pick the displays that are meant for them. This allows us to
keep the old platform data, and thus we avoid the need to change the
board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently have separate device/driver for each DSS HW module. The DPI
and SDI outputs are more or less parts of the DSS or DISPC hardware
modules, but in SW it makes sense to represent them as device/driver
pairs similarly to all the other outputs. This also makes sense for
device tree, as each node under dss will be a platform device, and
handling DPI & SDI somehow differently than the rest would just make the
code more complex.
This patch modifies arch/arm/mach-omap2/display.c to create platform
devices for DPI and SDI, and later patches will implement driver for
them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using omap_device_build() to create the omap_devices for DSS
hwmods, create them with a custom function. This will allow us to create
a parent-child hierarchy for the devices so that the omapdss_core device
is parent for the rest of the dss hwmod devices.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:
- Remove struct omap_display_platform_data. It was used just as a
wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
dss hwmods do not need the platform data. This should also work better
for DT, as we can create omapdss device programmatically in generic omap
boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
that the dss hwmod drivers can call.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lzYq
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-dss-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Clean up for omap DSS board init in preparation for adding DT support.
By Tomi Valkeinen
via Tomi Valkeinen (1) and Tony Lindgren (1)
* tag 'omap-cleanup-dss-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
OMAPDSS: DSI: implement generic DSI pin config
OMAPDSS: Taal: move reset gpio handling to taal driver
OMAPDSS: TFP410: rename dvi files to tfp410
OMAPDSS: TFP410: rename dvi -> tfp410
OMAP: board-files: remove custom PD GPIO handling for DVI output
OMAPDSS: panel-dvi: add PD gpio handling
Resolved context conflicts in arch/arm/mach-omap2/board-omap4panda.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=KYD3
-----END PGP SIGNATURE-----
Merge tag 'omap-dt-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Minor DT updates based on the dt-missed-3.4 branch
By Benoit Cousson (3) and Peter Ujfalusi (2)
via Tony Lindgren
* tag 'omap-dt-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPqwArAAoJEBvUPslcq6Vz0KMP+wWpRkFC+Retu1O1Lxy00Ea4
Zjg5wVfYGLuDAJf3i0xFKcDZA8AfDJws/kHi4sC0cbP296AfHqz7I25gKZqPoXf4
Y6iDRU/qLlO8djhJh7i+OP7/A4IlgMtOlMWJEZXrmhvuHRI5VusfpU/2p802yvFR
xn3oWJrQ1WtE+vvNo9sK67HXLogt+49r83XGWNY66WGePKTpBf/LD+wN7zsCVaW2
xK6vqg6Z/jq8naS6WN9+zdhqgB8huULM9RX/FcOmV8hgm9oSJrqzxHIB9jyVvjXQ
OMTz7WjHlakkneYBWxEGCsF8I4w5PJIXOav1OACvrsERKZpPJ0AmvYW05ZusJwLC
XWuYER9v+IJG1zzym7SBa/jIkGWrCKrQKxERvi8MD9NUl2y33flGzS89Hvm9Zjap
TO5U2yXIADqL83zHhtkgmWT6isHnFbQcwbc2Nz+oh/0Tnm2vrwRf88jxeFVX0k7D
l9A+XgPpUeoVEdyFtb1Gt++xojuwgEjZWKHuMfS+fJrj3WwolC2MLAVW6pDsTTQd
AERUuOHMgzODQ2Jx1rnljTAh57+3gVkw2iICtrWzecbbqHb6bOiB/sRN1KK+oQKh
CDiH2TzibDL1T+WDLFHBJTx0eTbRiQjViYaYtgM28k3r+wlNNRbf7WTU8PjA7AZp
rd/0s6+c+/kI4BcRVVF/
=ALlA
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-timer-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup2
Timer changes to make it easier to support various SoCs
By Vaibhav Hiremath
via Tony Lindgren
* tag 'omap-cleanup-timer-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Make OMAP clocksource source selection using kernel param
ARM: OMAP2+: Replace space with underscore in the name field of system timers
ARM: OMAP1: Add checks for possible error condition in timer_init
except for the RNG driver that will be done later on.
As this depends on omap-devel-hwmod-data-for-v3.5 and causes merge
conflict with omap-fixes-non-critical-for-v3.5, this branch is based
on merge of the two.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w67p
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-devices-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup2
Changes to split plat-omap/devices.c into mach-omap1 and mach-omap2
except for the RNG driver that will be done later on.
As this depends on omap-devel-hwmod-data-for-v3.5 and causes merge
conflict with omap-fixes-non-critical-for-v3.5, this branch is based
on merge of the two.
By Tony Lindgren (7) and others
via Tony Lindgren (4) and Paul Walmsley (1)
* tag 'omap-cleanup-devices-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
ARM: OMAP: Move omap_mmc_add() to mach-omap1
ARM: OMAP2: Use hwmod to initialize mmc for 2420
ARM: OMAP2+: Move omap_dsp_reserve_sdram_memblock() to mach-omap2
ARM: OMAP1: Move omap_init_uwire to mach-omap1
ARM: OMAP1: Move omap_init_audio() to keep the devices in alphabetical order
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BR/x
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-hwmod-data-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm
Data changes related to omap hwmod
By Paul Walmsley (4) and others
via Paul Walmsley (1) and Tony Lindgren (1)
* tag 'omap-devel-hwmod-data-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
Note that this depends on omap-devel-hwmod-for-v3.5.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPqsOuAAoJEBvUPslcq6VzT0UP/Ash5WqQ6AOz6vfvJVwYs7FA
/ITUt05h0bpd8WbO5jDRNkUWL/NKfJ9zIfyEt24OVrPI0dhMOLVkPFdCTsQujIcG
5IztIDg4VnebUKyelsW6NMUsfUXURRVmcl4kYlYcRH3zaNOHz+ae2RUVwzTX0/RR
2T8+tFnjjyilXQ3T6swUnhMzB/BARpKK4ghO1vambIkRoe7ZaCdyzenBC3010ngx
zHikigd27S6FKOhX6jJJNFtp6WK6bKWSOEBfXaR5SOgFM45VDQZltQMNa/EBbktl
TXFQL0vRTIAOTGRrbhtcD/ny6kiS+NxC9ZeFbEFpQVdiZwJyPKpqOW10hV/KKeTR
9fuxPnCoc9DgaEx3YyFY2jjvRfgwGL0Dox/mu508RdOxTOgWcIJ+dYK1lihtMCrI
I5A0Mh35h9ykUmU2m9Hw0odwB+JdPL6HgYKwKfYAgjoGMMeQHPzt7m77dsEu8PZr
XpQAmT+MH0D2ATbGvISChRJSi1Zac2dd8WmKKLoE7Saq8U63G0IvocIdO7Xbr3/l
BxnCAOH5VQ9f5CBdLWNFKwKsc+y0EFGZRuv4CF6Y3qYwLxfmubXN6P0u9HjwVuNl
beWhujTpaeQJ0x0ZHVxA0UYjoJuNx0xJAJTeuN5XwfH2r9lX82TYxgs4CyC6fdH7
Ueb5QfhecxMx1RzaoA/G
=ECOj
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-prcm-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm
Updates for PRCM (Power, Reset, Clock Management).
Note that this depends on omap-devel-hwmod-for-v3.5.
By Kevin Hilman (3) and others
via Paul Walmsley (2) and Tony Lindgren (1)
* tag 'omap-devel-prcm-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
ARM: OMAP2+: dmtimer: cleanup iclk usage
ARM: OMAP4+: Add prm and cm base init function.
ARM: OMAP2/3: Add idle_st bits for ST_32KSYNC timer to prcm-common header
ARM: OMAP3: Fix CM register bit masks
ARM: OMAP: clock: convert AM3517/3505 detection/flags to AM35xx
ARM: OMAP3: clock data: treat all AM35x devices the same
ARM: OMAP3: clock data: replace 3503/3517 flag with AM35x flag for UART4
Note that this depends on a fix in omap-fixes-non-critical-for-v3.5,
so it's based on that.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=V8mj
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-renames-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup2
Simplify some SoC config options before things get too unreadable.
Note that this depends on a fix in omap-fixes-non-critical-for-v3.5,
so it's based on that.
By Kevin Hilman (3) and others
via Tony Lindgren
* tag 'omap-cleanup-renames-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to SOC_AM33XX
ARM: OMAP2+: Kconfig: convert SOC_OMAPTI81XX to SOC_TI81XX
ARM: OMAP: igep0020: Specify the VPLL2 regulator unconditionally
ARM: OMAP2+: INTC: fix Kconfig option for TI81XX
ARM: OMAP2+: remove incorrect irq_chip ack field
ARM: OMAP4: Adding ID for OMAP4460 ES1.1
ARM: OMAP4: panda: add statics to remove warnings
ARM: OMAP2+: Incorrect Register Offsets in OMAP Mailbox
ARM: OMAP: fix trivial warnings for dspbridge
ARM: OMAP4: hsmmc: check for null pointer
ARM: OMAP1: fix compilation issue in board-sx1.c
No need to have an OMAP prefix on these SoCs that are in the family
but arent' really called OMAP.
Simple rename: CONFIG_SOC_OMAPAM33XX --> CONFIG_SOC_AM33XX
No functional change.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated for the driver config change also]
Signed-off-by: Tony Lindgren <tony@atomide.com>
No need to have an OMAP prefix on these SoCs that are in the family
but arent' really called OMAP.
Simple rename: CONFIG_SOC_OMAPTI81XX --> CONFIG_SOC_TI81XX
No functional change.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Conflicts:
drivers/video/omap2/displays/panel-taal.c
Merge OMAP DSS related board file changes. The branch will also be
merged through linux-omap tree to solve conflicts.
Currently cpu_is_omap3517() actually detects any device in the AM35x
family (3517 and no-SGX version 3505.) To make it more clear what is
being detected, convert the names from 3517 to AM35xx.
This adds a new soc_is_am35xx() which duplicates the cpu_is_omap3517().
In order to avoid cross-tree dependencies with clock-tree changes,
cpu_is_omap3517() is left until the clock changes are merged,
at which point cpu_is_omap3517() will be completely removed.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: change to use soc_is_omap instead]
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are several checks for AM35x devices done using
if (cpu_is_omap3517() || cpu_is_omap3505())
However, since the 3505 is just a 3517 without an SGX, the 3505 check
is redundant because cpu_is_omap3517() will always be true whenever
cpu_is_omap3505() is true. From <plat/cpu.h>:
#define cpu_is_omap3505() (cpu_is_omap3517() && !omap3_has_sgx())
Therefore, remove the redunant 3505 checks. This helps move towards
removal of SoC detection that depends on specific IP detection.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to pass dma request lines in platform data to
MMC driver the same way as we already do for omap2430 and later.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This hardware exists only on 2430 and later omaps, so there's no
need to have it in plat-omap/devices.c.
Note that we don't have any users for exported omap_dsp_get_mempool_base(),
so we can make it static.
Signed-off-by: Tony Lindgren <tony@atomide.com>
These supplies going to be needed for the twl6040 driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These supplies going to be needed for the twl6040 driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
V1V8 supply from twl6030 commonly used as VIO for the machine.
V2V1 is adviced to supply the twl6040, and also to feed the twl6030's
VCXIO_IN, and VDAC_IN inputs.
Create the common regulator configurations for these regulators:
Make the V2V1 as supply_regulator for VCXIO, VDAC.
Add twl6040 (1-004b) as consumer for V1V8, and V2V1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for the pm regulator changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Beagleboard-xM (all revisions) only MMC1_DAT0-MMC1_DAT3 are wired up.
Tested on Beagleboard-xM Rev C1 and Beagleboard Rev B4.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the OMAP3 MUSB OTG controller to the LogicPD
OMAP3530 SOM-LV[1] and Torpedo[2] DevKits
[1] - www.logicpd.com/products/system-on-modules/omap35x-som-lv/
[2] - www.logicpd.com/products/system-on-modules/omap35x-torpedo-som/
Signed-off-by: Ashwin Bihari <ashwin.bihari@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the required am35xx_emac_init() call to the craneboard init
function.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform device registratation for HDMI audio codec. This is to
be able to transmit audio through the HDMI output featured in Pandaboard
and PandaboardES boards.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform device registratation for HDMI audio codec. This is to
be able to transmit audio through the HDMI output featured in SDP4430
and Blaze boards.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform registration for the devices HDMI audio support. The
omap-hdmi-audio-dai platform device is to be used by the ASoC HDMI
CPU DAI driver. The omap-hdmi-audio platform device is to be used
by the ASoC HDMI machine driver that links together the ASOC CPU DAI,
ASoC plaform and ASoC codec drivers.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP-based boards can have two different flash memories, a OneNAND or
a NAND device. The boot configuration pins (sys_boot) are used to
specify which memory is available.
Also, this patch removes unnecesary code for registering the OneNAND.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: fixed up a minor checkpatch warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
board_onenand_init() and board_nand_init() initialization functions are
used to initialize OneNAND and NAND memories respectively. But only
board_nand_init() was visible to be used from board code. This patch makes
possible to initialize a OneNAND flash memory within platform code.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the power off feature of the TPS65930 on-board PMIC.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "uim" deamon requires sysfs entries that are filled in using
this platform data.
Signed-off-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
HIGMEM support in kernel is quite mature now and we have boards
like ZOOM, PANDA, SDP where 1 GB memories are installed. With
HIGHMEM disabled not all of the 1GB of RAM (only ~700MB) can be
accessed. Hence, enable HIGMEM to make use of the entire memory.
On the boards which doesn't have more than 768 MB memory, all
the memory is directly mapped in "lowmem" and highmem isn't
exercised. Hence, there should be no impact by enabling HIGHMEM
for boards that do not need it.
Tested on OMAP4460 Panda-ES.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The supply is connected to the DSS DO-D5 pins and is thus needed for
both serial and parallel display interfaces on the igep0030 as well as
the igep0020.
If the igep0030 module isn't connected to a display, no DSI or DPI
display will be specified in board code, and the DSS driver won't enable
to VPLL2 regulator anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The INTC core is using a Kconfig option for TI816x which doesn't
exist. Convert it to use TI81XX.
Cc: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Each irq_chip for the main interrupt controller has offsets set for irq
masking registers, which added to respective base results in a pointer
to appropriate hardware register. However this is not correct for
INTC_CONTROL as there is only one INTC_CONTROL register. This does not
cause problems because generic ack code is never called, but remove
this assignment to avoid confusion.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add statics to board-omap4-panda.c's internal functions and data
structures to remove sparse warnings:
arch/arm/mach-omap2/board-omap4panda.c:234:29: warning: symbol
'omap_panda_wlan_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:441:24: warning: symbol
'omap4_panda_dvi_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:451:12: warning: symbol
'omap4_panda_dvi_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:512:13: warning: symbol
'omap4_panda_display_init' was not declared. Should it be static?
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the register offsets are incorrect in the OMAP mailbox code
(arch/arm/mach-omap2/mailbox.c) for the OMAP4_MAILBOX_IRQ* macros. The
discrepancy is with p.224 of TI document SPRUGX9 and p3891 of SWPU231K.
Acked-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Henry Chan <enli.chan@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/plat-omap/devices.c: In function 'omap_dsp_reserve_sdram_memblock':
arch/arm/plat-omap/devices.c:170: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'phys_addr_t'
arch/arm/mach-omap2/dsp.c: In function 'omap_dsp_init':
arch/arm/mach-omap2/dsp.c:60: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'phys_addr_t'
arch/arm/mach-omap2/dsp.c:60: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'phys_addr_t'
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Current OMAP code supports couple of clocksource options based
on compilation flag (CONFIG_OMAP_32K_TIMER). The 32KHz sync-timer
and a gptimer which can run on 32KHz or system clock (e.g 38.4 MHz).
So there can be 3 options -
1. 32KHz sync-timer
2. Sys_clock based (e.g 13/19.2/26/38.4 MHz) gptimer
3. 32KHz based gptimer.
The optional gptimer based clocksource was added so that it can
give the high precision than sync-timer, so expected usage was 2
and not 3.
Unfortunately option 2, clocksource doesn't meet the requirement of
free-running clock as per clocksource need. It stops in low power states
when sys_clock is cut. That makes gptimer based clocksource option
useless for OMAP2/3/4 devices with sys_clock as a clock input.
So, in order to use option 2, deeper idle state MUST be disabled.
Option 3 will still work but it is no better than 32K sync-timer
based clocksource.
We must support both sync timer and gptimer based clocksource as
some OMAP based derivative SoCs like AM33XX does not have the
sync timer.
Considering above, make sync-timer and gptimer clocksource runtime
selectable so that both OMAP and AMXXXX continue to use the same code.
And, in order to precisely configure/setup sched_clock for given
clocksource, decision has to be made early enough in boot sequence.
So, the solution is,
Use standard kernel parameter ("clocksource=") to override
default 32k_sync-timer, in addition to this, we also use hwmod database
lookup mechanism, through which at run-time we can identify availability
of 32k-sync timer on the device, else fall back to gptimer.
Also, moved low-level SoC specific init code to respective files,
(mach-omap1/timer32k.c and mach-omap2/timer.c)
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Depending on the bootloader, passing command-line arguments
with spaces may have issues. Some bootloaders doesn't seem
to pass along the quotes, passing only 'gp' part of the string,
which leads to wrong override configuration.
The only affected kernel parameter configuration for OMAP family
is "clocksource=", used to override kernel clocksource.
So this patch changes "gp timer" => "gp_timer", for clockevent,
clocksource and timer irq_handler.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
fix for a longstanding watchdog timer integration problem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gBFx
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-c-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-hwmod-data
Some OMAP IP block data additions for 3.5, along with a
fix for a longstanding watchdog timer integration problem.
id 0 is already used and causes errors at boot:
WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0x9c/0xac()
sysfs: cannot create duplicate filename '/devices/platform/reg-fixed-voltage.0'
Fix it by using the next available one (id=1).
This was caused by 5b3689f4 (ARM: OMAP2+: smsc911x: Add fixed
board regulators) that did not account for some regulators
already being used.
Signed-off-by: Enrico Butera <ebutera@users.berlios.de>
[tony@atomide.com: updated comments for regression causing commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qEmC
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-hwmod-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Clean up of hwmod to shrink down the IP block interconnections
By Paul Walmsley
via Paul Walmsley (1) and Tony Lindgren (1)
* tag 'omap-cleanup-hwmod-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits)
ARM: OMAP2xxx: hwmod data: start to fix the IVA1, IVA2 and DSP
ARM: OMAP3: hwmod data: add IVA hard reset lines, main clock, clockdomain
ARM: OMAP3: hwmod data: fix IVA interface clock
ARM: OMAP2xxx: hwmod data: share common interface data
ARM: OMAP2xxx: hwmod data: share common hwmods between OMAP2420 and OMAP2430
ARM: OMAP2+: hwmod data: remove forward declarations, reorganize
ARM: OMAP: hwmod: remove code support for direct hwmod registration
ARM: OMAP2+: hwmod data: convert to link registration
ARM: OMAP2+: hwmod: add support for link registration
ARM: OMAP2+: hwmod: consolidate finding the MPU port index and storing it
ARM: OMAP2+: hwmod: add function to iterate over struct omap_hwmod_ocp_if
ARM: OMAP2+: hwmod: add _find_mpu_rt_port()
ARM: OMAP2+: hwmod: extend OCP_* register offsets from 16 to 32 bits
ARM: OMAP4: hwmod data: uncomment some "excluded" hwmods
ARM: OMAP4: hwmod data: add OCP_USER_DSP; mark omap44xx_dsp__iva appropriately
ARM: OMAP4: hwmod data: remove bandgap hwmod
ARM: OMAP3: hwmod data: GPTIMER12 is attached to a separate interconnect
ARM: OMAP3: hwmod data: add DSS->L3 interconnect for 3430ES1
ARM: OMAP3: hwmod data: fix interfaces for the MMC hwmods
ARM: OMAP2/3: hwmod data: update old names
...
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MQ+t
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-sparse-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Sparse and cppcheck warning fixes
By Paul Walmsley
via Paul Walmsley (1) and Tony Lindgren (1)
* tag 'omap-cleanup-sparse-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: clean up some cppcheck warnings
ARM: OMAP1: board files: deduplicate and clean some NAND-related code
ARM: OMAP: USB: remove unnecessary sideways include
ARM: OMAP: DMA: use constant array maximum, drop some LCD DMA code
ARM: OMAP: OCM RAM: use memset_io() when clearing SRAM
ARM: OMAP: fix 'using plain integer as NULL pointer' sparse warnings
ARM: OMAP2+: GPMC: resolve type-conversion warning from sparse
ARM: OMAP1: OHCI: use platform_data fn ptr to enable OCPI bus
ARM: OMAP1: OCPI: move to mach-omap1/
ARM: OMAP: add includes for missing prototypes
ARM: OMAP2+: declare file-local functions as static
Signed-off-by: Olof Johansson <olof@lixom.net>
As a prerequisite for merging the lpc32xx DT changes, this
pulls in the depends/i2c/lpc32xx branch that contains
changes to the pnx-i2c driver, which are already in the
i2c tree. The branch is available also on
git://git.antcom.de/linux-2.6.git lpc32xx/i2c
Roland Stigge <stigge@antcom.de> writes:
this is the series of the 4 patches adding device tree support to i2c-pnx
(used by LPC32xx) that Wolfram Sang already applied to the i2c subsystem.
Since both drivers/i2c/ and mach-lpc32xx are touched here, there will
probably be conflicts that you need to be aware of.
I'm posting this again for arm-soc since the actual mach-lpc32xx specific
DT conversion builds upon those changes (see next pull request), especially
in arch/arm/mach-lpc32xx/common.c.
Wolfram already gave permission to merge this via arm-soc, but please
coordinate and tell me if I can help resolving this.
Further, this implicitly updates the next/dt branch to v3.4-rc4, which
causes a trivial conflict from a change in one branch in code that
gets removed in another.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a rebased version of parts of
git://git.stlinux.com/spear/linux-2.6.git spear-v3.5
which was accidentally based on the linux-next tree and mixed too
many different things. The pinctrl related changes from the same
branch are now in the spear/pinctrl branch of arm-soc.
There are a few non-DT cleanups mixed in here, but fundamentally
it's all related to the DT conversion.
* spear/dt: (9 commits)
ARM: spear: remove most mach/*.h header contents
SPEAr: Update defconfigs
SPEAr: Add PL080 DMA support for 3xx and 6xx
ARM: SPEAr3xx: Add device-tree support to SPEAr3xx architecture
SPEAr3xx: Replace printk() with pr_*()
SPEAr6xx: Add compilation support for dtbs using 'make dtbs'
SPEAr3xx: Add clock instance of usb hosts - ehci and ohci 0 and 1
SPEAr: Use CLKDEV_INIT for defining clk_lookups
ARM: SPEAr600: Change FSMC and SMI clock names
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.
This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.
The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:
{
0, // pin num for clock lane +
1, // pin num for clock lane -
2, // pin num for data1 lane +
3, // pin num for data1 lane -
...
}
The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The reset GPIO for Taal panel driver is currently requested in the
4430sdp board file. This patch moves the gpio request/free into the Taal
driver, where it should be.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the tfp410 driver has been renamed in the code, this patch
finishes the renaming by renaming the files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 DPI-to-DVI chip was named quite badly as "DVI
panel driver". This patch renames the code to use tfp410 name for the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the panel-dvi driver handles the PD (power-down) GPIO, we can
remove the custom PD handling from the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
platform_device pdev can be NULL if CONFIG_MMC_OMAP_HS is not set.
Add check for NULL pointer. while at it move the duplicated functions
to omap4-common.c
Fixes the following boot crash seen with omap4sdp and omap4panda
when MMC is disabled.
Unable to handle kernel NULL pointer dereference at virtual address 0000008c
pgd = c0004000
[0000008c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 Not tainted (3.4.0-rc1-05971-ga4dfa82 #4)
PC is at omap_4430sdp_init+0x184/0x410
LR is at device_add+0x1a0/0x664
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If dtb is provided the needed device will be created dynamically.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If dtb is provided the needed device will be created dynamically.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without runtime PM enabled, hwmod needs to leave all IP blocks in an
enabled state by default so any driver access to the HW will succeed.
This is accomplished by seting the postsetup_state to enabled for all
hwmods during init when runtime PM is disabled.
Currently, we have a special case for WDT in that its postsetup_state
is always set to disabled. This is done so that the WDT is disabled
and the timer is disarmed at boot in case there is no WDT driver.
This also means that when runtime PM is disabled, if a WDT driver *is*
built in the kernel, the kernel will crash on the first access to the
WDT hardware.
We can't simply leave the WDT module enabled, because the timer is
armed by default after reset. That means that if there is no WDT
driver initialzed or loaded before the timer expires, the kernel will
reboot.
To fix this, a custom reset method is added to the watchdog class of
omap_hwmod. This method will *always* disarm the timer after hwmod
reset. The WDT timer then will only be rearmed when/if the driver is
loaded for the WDT. With the timer disarmed by default, we no longer
need a special-case for the postsetup_state of WDT during init, so it
is removed.
Any platforms wishing to ensure the watchdog remains armed across the
entire boot boot can simply disable the reset-on-init feature of the
watchdog hwmod using omap_hwmod_no_setup_reset().
Tested on 3530/Overo, 4430/Panda.
NOTE: on 4430, the hwmod OCP reset does not seem to rearm the timer as
documented in the TRM (and what happens on OMAP3.) I noticed this
because testing the HWMOD_INIT_NO_RESET feature with no driver loaded,
I expected a reboot part way through the boot, but did not see a
reboot. Adding some debug to read the counter, I verified that right
after OCP softreset, the counter is not firing. After writing the
magic start sequence, the timer starts counting. This means that the
timer disarm sequence added here does not seem to be needed for 4430,
but is technically the correct way to ensure the timer is disarmed, so
it is left in for OMAP4.
Special thanks to Paul Walmsley for helping brainstorm ideas to fix
this problem.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: updated the omap2_wd_timer_reset() function in the
wake of commit 3c55c1baff ("ARM:
OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset
wait for reset status""); added kerneldoc; rolled in warning fix from Kevin]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use 'common' as name for the common irq number in hwmod data for the McBSP
ports. The same name already in use for OMAP2430, and OMAP3.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Restore of context is not done for OMAP4. This patch
adds the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE in the OMAP4
hwmod data which activates the restore for OMAP4.
Currently the OMAP4 does not hit device off still the
driver may have support for it.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Wamsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use 'common' as name for the common irq number in hwmod data for the McBSP
ports. The same name already in use for OMAP2430, and the OMAP4 hwmod data
will be using the same name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ1W hwmod for all OMAP2xxx devices.
Assume that OMAP2xxx chips have the same HDQ idle handling bug
as OMAP3:
http://www.spinics.net/lists/linux-omap/msg63576.html
and set the OCPIF_SWSUP_IDLE flag accordingly on the HDQ's OCP interface.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ1W hwmod for OMAP34xx, OMAP36xx, and AM3505/3517 devices.
According to the respective TRMs, it doesn't appear to be available for the
816x/814x or the AM335x.
The OCPIF_SWSUP_IDLE flag is added to work around an apparent hardware
bug: the hardware is not taking the CM_FCLKEN*_CORE.EN_HDQ bit into
account when considering whether to go idle:
http://www.spinics.net/lists/linux-omap/msg63576.html
This causes HDQ transfers to fail or become corrupt. Thanks to
NeilBrown for his help diagnosing and testing fixes for this problem.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
Much of the HDQ1W integration data is common between multiple generations
of OMAP SoCs, so rather than make several copies, we add it once into
files which are compiled for multiple SoCs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
Implement a custom reset function for the HDQ1W IP block. This is
because the HDQ1W IP block, like I2C, has an internal clock gating bit
that needs to be toggled after setting the SOFTRESET bit to allow the
reset to propagate.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Avinash.H.M <avinashhm@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
Add MMC for 2420 so we can pass the DMA request lines the same
way as we already do on omap2430 and later.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: updated to apply on top of the 3.5 hwmod cleanup;
changed mmc hwmod name/class to "msdi" as documented in the 2420 TRM Rev X;
added sysconfig register information; added 16 bit register width flag;
added MSDI custom reset code]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
powerdomain, PRM, and CM changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Q4kv
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-b-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-prcm
Some OMAP PRCM updates for 3.5. Includes some clock, clockdomain,
powerdomain, PRM, and CM changes.
The system dma module has capabiities register indicating
the support for descriptor loading, constant fill, etc.
Use this instead of OMAP revision check to identify the features
supported runtime.
This avoids patching the code for feature SOCs which has
those capabilities.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
EMIF, GMPC and DMM driver can ioremap() the address
space as part of driver intialisation and there is
no need to have static IO mapping for them.
Hence remove the un-used static IP space and let
the respective drivers manage it as part if driver
init.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Current OMAP code doesn't use any of the OMAP_WKG_ENB_SECURE_*
registers.
So remove those defines.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Since OMAP4 code base now makes use of OMAP4 specific PRCM functions,
cm2xxx_3xxx.c need not be compiled for OMAP4 only builds.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Clean up clockdomains3xxx_data.c a bit by removing the superfluous
commas in gfx_sgx_3xxx_wkdeps[].
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With patch 'ARM: OMAP2+: powerdomain: Wait for powerdomain transition
in pwrdm_state_switch()', the pwrdm_clkdm_state_switch() API becomes
duplicate of pwrdm_state_switch().
Get rid off duplicate pwrdm_clkdm_state_switch() and update the
users of it with pwrdm_state_switch()
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the correct clockdomain for the HDQ functional clock. This is needed
for the clock and hwmod PM code to work correctly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
The current DPLL code enables and disables autoidle features
without checking whether the autoidle register is available.
Fix this by putting a check for the existence of the autoidle
register in the DPLL data.
With such a check in place, for DPLLs which do not support this
feature, simply skipping the autoidle_reg entry in the DPLL data
is sufficient.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We do not use iclk anywhere in the dmtimer driver and so removing it.
Hence removing the timer iclk entries from OMAP4 clkdev table as well.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Instead of statically defining seperate arrays for every OMAP4+ archs,
have a generic init function to populate the arrays. This avoids the
need for creating new array for every arch added in the future that
reuses the prm and cm registers read/write code.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add missing idle_st bit for 32k-sync timer into the prcm-common
header file, required for hwmod data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register bits for MPU_CLK_SRC and IVA2_CLK_SRC in CM_CLKSEL1_PLL
register are 3 bits wide. Fix the MASK definition accordingly.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To improve the clarity of the code, replace the CK_3517 flag used in
the clock data with CK_AM35XX. The CK_3505 flag can also be
removed, since it is now unused.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The init for 3505/3517 specific clocks depends on the ordering of
cpu_is checks, is error prone and confusing (there are 2 separate
checks for cpu_is_omap3505()).
Remove the 3505-specific checking since CK_3505 flag is not used, and
treat all AM35x clocks the same.
This means that the SGX clock (the only AM35x clkdev not currently
flagged for 3505) will now be registered on 3505, but that is
harmless. That can be cleaned up when the clkdev nodes are removed in
favor of them being registered by hwmod.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The AM35x UART4 is common to all AM35x devices, so use CK_AM35XX instead
of (CK_3505 | CK_3517), which is equivalent.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
At init time, check the powerdomains lookup is successful otherwise
exit the cpuidle driver init function with -ENODEV like what is done for the
omap3 cpuidle driver.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This reverts commit 46f8c3c7e9.
The commit above swapped the DSI1_PPID and DSI2_PPID register fields in
CONTROL_DSIPHY to be in sync with the newer public OMAP TRMs(after version V).
With this commit, contention errors were reported on DSI lanes some OMAP4 SDPs.
After probing the DSI lanes on OMAP4 SDP, it was seen that setting bits in the
DSI2_PPID field was pulling up voltage on DSI1 lanes, and DSI1_PPID field was
pulling up voltage on DSI2 lanes.
This proves that the current version of OMAP4 TRM is incorrect, swap the
position of register fields according to the older TRM versions as they were
correct.
Cc: stable@vger.kernel.org # v3.2+
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
struct powerdomain varialbes are all file local, make them static.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[khilman@ti.com: update changelog, drop error check in fast path]
Signed-off-by: Kevin Hilman <khilman@ti.com>
Reduce the scope of the omap3_idle_data to the file as it is only used
in cpuidle34xx.c.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Simplify the indentation by removing the useless 'else' statement.
Remove the first loop for the 'idx' search as we have it already
with the 'index' passed as parameter.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We are storing the 'omap3_idle_data' in the private data field
of the cpuidle device. As we are using this variable only in this file,
that does not really make sense. Let's use the global variable directly.
As the table is initialized statically, let's remove the initialization at
startup too.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Initialize the omap3_idle_data array at compile time, that will allow
to remove the initialization at boot time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We do not longer need the ''cpuidle_params_table' array as
we defined the states in the driver and we checked they are
all valid.
We also remove the structure definition as it is no longer used.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With the previous changes all the states are valid, except the last
state which is now handled at runtime by next_valid_state() based on
the errata flags.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[khilman@ti.com: minor changelog rework]
Signed-off-by: Kevin Hilman <khilman@ti.com>
The errata check is done in the next_valid_state function, no need to check
that in the omap3_idle_init function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Use the new cpuidle API and define in the driver the states.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As suggested, this table is an optimized version for rx51 and we
remove it in order to consolidate the cpuidle code between omap3
and omap4, we remove this specific data definition which is used
to override the default omap3 latencies but at the cost of extra
code and complexity.
In order to not lose the values which probably took time to be
measured, the table is converted into a comment with an array
description.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We initialized it at compile time, no need to do that at boot
time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We are storing the 'omap4_idle_data' in the private data field
of the cpuidle device. As we are using this variable only in this file,
that does not really make sense. Let's use the global variable directly.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We initialize the omap4_idle_data variable at compile time allowing us
to remove in the next patch the initialization done at boot time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add the static declaration for the omap4_idle_data variable because its scope
is in the file only.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We do not longer need this table as we defined the values
in the driver states.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The cpuidle API allows to declare statically the states in the driver
structure. Let's use it.
We do no longer need the fill_cstate function called at runtime and
by the way adding more instructions at boot time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The 'valid' field is never used in the code, let's remove it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omapdss driver needs to use the omap_pm_set_min_bus_tput(), so add a new
entry for that in omapdss's platform data, and set it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
OMAP44xx family of SoCs. There still seem to be a few missing, such
as those for the MMU IP blocks, but this seems to cover the bulk of
the remainder.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ToTm
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-a-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-hwmod
Add in most of the remaining hwmods (IP block descriptions) for the
OMAP44xx family of SoCs. There still seem to be a few missing, such
as those for the MMU IP blocks, but this seems to cover the bulk of
the remainder.
control code for OMAP SoCs. In particular, this series results in
a considerable diffstat savings by changing the way that IP block
interconnections are defined.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPkE3+AAoJEMePsQ0LvSpLzrMQAJV6ie5CZTu8FC+dIVplnn5q
Tv12c1CUb1SRCxSYRFhxVDm+jL5d7sQ99C/HZ7kStz23OVn+r8OlyFmLTLk59Bkl
tf8iBEcMyaB+oMvDddYyzcetjT3gpG0yOZC7FMYkfpwCd8DM2hk+8k4JawXe8cqu
3HzDoeXynbF5QCgZpaORAZT8FH4tmTJl1XMkENIflmuwDV8QvwrKZmcJILnr2r+p
pZhCt972xWV6PZYJ0HvdjgabbQ92jyIFggqNeA/BBNoMhfTXbhUFpZE2Oy/Y5vmu
5qXR8yKFesV7jeXyiOMBzHLhMv9Rf4ivAE6u3aVmSIGrKvYTIPNEX9ric8Ryv1Um
33y6NTLv4SsTeKqmL4gCFmbkTz9aixbonThr1yr9ZCHD7jXwjLUjkxyXyjTZRAOV
BWWgMiTKxXmJ1o2AJ/Y3xEWkWsmeafSdKpEF9aPpLyX6bW5oYObAJ1KorvnUut6W
YLWVP3JOfPFpcLHLFA/wtLbk+FwyKdbkLTyP29qJDvg3mUjJG0JGRaHA20hiZIOC
zvxmq/Or7gMvDFXOY3EY97xnDLFbiM+efT/5KuTXI2sel2ojcL8uVJU6qvxGN86h
5rz+E7RXpdtYafvtF0AKdX65Ntyqpe5EUUSnQJAB1xTC9CkFlVVn21R2PO+1P0+e
xWjiHLK/+amqrZa+zkks
=NqUz
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-b-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into cleanup-hwmod
Clean up various aspects of the OMAP hwmod code, which is the IP block
control code for OMAP SoCs. In particular, this series results in
a considerable diffstat savings by changing the way that IP block
interconnections are defined.
Add a skeleton hwmod for the DEBUGSS and associated interconnect data.
This is a basic set of data that will need further additions as
further DEBUGSS information becomes available.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the PRCM, CM, PRM, and related hwmod and associated interconnect
data. These IP blocks handle most of the on-chip power, reset, and clock
control.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the System Control Module hwmod and associated interconnect data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the OCP-WP hwmod and associated interconnect data. The OCP-WP,
or OCP watchpoint, can be used to collect interconnect data and
transmit it via the STM port.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the OCM RAM IP block and interconnect data. This is an oh-chip
block of SRAM connected directly to the L3 bus.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the OCP2SCP IP block and interconnect data. The OCP2SCP can be
used in conjunction with the on-chip embedded USB PHY, associated with
the OTG controller.
Add the on-chip full-speed USB host controller IP block and
interconnect data.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the SL2 interface IP block and interconnect data. The SL2 is related
to the IVA-HD subsystem.
Add IP block and interconnect data for the C2C ("Chip-to-chip")
interconnect. This can provide a direct system interconnect link to
other devices stacked on the OMAP package.
Add the ELM IP block and interconnect data. The ELM can be used
to locate errors in NAND flash connected to the GPMC.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the McASP hwmod and associated interconnect data. The McASP is a
general-purpose audio serial port.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the Slimbus hwmods and associated interconnect data. The Slimbus
IP blocks implement a two-wire serial interface.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the GPU hwmod and associated interconnect data. The GPU is a
graphics accelerator.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the EMIF1 and 2 hwmods and associated interconnect data. The EMIFs
are SDRAM interface IP blocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the GPMC hwmod and associated interconnect data. The GPMC is a
programmable parallel-bus memory controller.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ/1-wire hwmod and associated interconnect data. The
HDQ/1-wire IP block is a low-speed serial interconnect.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add hwmod data for the OMAP4 FDIF IP block.
This patch also includes a change (originally from Fernando Guzman
Lugo <fernando.lugo@ti.com>) to set a softreset delay for the FDIF IP
block:
http://www.spinics.net/lists/arm-kernel/msg161874.html
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Cc: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: rearranged to match script output; fixed FDIF end address to
match script data; wrote trivial changelog; combined the FDIF portion of
Fernando's srst_udelay patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The PRM and CM implicit clockdomains will soon be used by OMAP44xx.
So, make them common to OMAP2+ and modify the OMAP4 clockdomains code
so use of these clockdomains doesn't crash the system.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
N800 logs this message on boot:
[ 0.182281] omap_hwmod: iva: cannot be enabled for reset (3)
Fix by creating basic IVA1 and DSP hwmods for OMAP2420, and a basic IVA2
hwmod for OMAP2430. There is still more information to be added, but
this should resolve the immediate issue.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The IVA hwmod data is missing some fields that cause the following
warning on boot:
[ 0.118011] omap_hwmod: iva: cannot be enabled for reset (3)
Fix by encoding the IP block's main functional clock, reset lines, and
clockdomain.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 hwmod data listed iva2_ck as an interface clock between the
IVA and L3. This is incorrect. iva2_ck is not an interface clock.
Since it cannot auto-idle, specifying it here prevents the IVA and at
least one of the CORE clockdomains from going idle, which causes PM
problems such as these upon system suspend:
[ 70.626129] Powerdomain (iva2_pwrdm) didn't enter target state 1
[ 70.626190] Powerdomain (core_pwrdm) didn't enter target state 1
Fix by specifying the actual interface clock in the hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Several struct omap_hwmod_ocp_if records can be shared between OMAP2420
and OMAP2430. Move these shared records out of the chip-specific files
into mach-omap2/omap_hwmod_2xxx_interconnect_data.c. This should save some
memory and source lines, at the cost of readability.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
After the link registration conversion, it's much easier to share some
hwmod data between OMAP2420 and 2430. Move the shareable data into a
common file. This should save some memory and lines of source, at the
cost of readability.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Reorganize the hwmod data to declare the IP blocks first and the
interconnects second. This allows us to remove the forward
declarations, which this patch also does. Saves some lines of source
data. While here, take the opportunity to synchronize the order of
the OMAP44xx hwmod data with the autogenerator output -- it's slightly
different due to past mismerges -- and fix a few minor typos and
whitespace problems in the files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Now that the data has been converted to use interface registration, we
can remove the (now unused) direct hwmod registration code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Register interconnect links between IP blocks, rather than the IP
blocks themselves. (The IP blocks will be registered as a side-effect
of registering the links.)
The objective is to reduce the number of lines of static data and
facilitate the sharing of IP block data between different SoCs. These
objectives come at the penalty of increased boot time due to increased
computation.
While here, fix a few whitespace problems and inaccurate variable names.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Add support for direct IP block interconnect ("link") registration to
the hwmod code via a new function, omap_hwmod_register_links(). This
will replace direct registration of hwmods, and a subsequent patch
will remove omap_hwmod_register().
This change will allow a subsequent patch to remove the hwmod data
link arrays. This will reduce the size of the hwmod static data and
also make it easier to generate the data files. It will also make it
possible to share some of the struct omap_hwmod records across
multiple SoCs, since the link array pointers will be removed from the
struct omap_hwmod.
The downside is that boot time will increase. Minimizing boot time
was the reason why the link arrays were originally introduced.
Removing them will require extra computation during boot to allocate
memory and associate IP blocks with their interconnects. However,
since the current kernel development focus is on reducing the number
of lines in arch/arm/mach-omap2/, boot time impact is now seemingly
considered a lower priority.
This patch contains additional complexity to reduce the number of
memory allocations required for this change. This reduces the boot
time impact: total hwmod link registration time was ~ 2655
microseconds with a simple allocation strategy, but is now ~ 549
microseconds[1] with the approach taken by this patch.
1. Measured on a BeagleBoard 35xx @ 500MHz MPU/333 MHz CORE, average
of 7 samples. Total uncertainty is +/- 61 microseconds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
An IP block's MPU interface port only needs to be found once. The result
can be cached to speed further lookups. This patch consolidates these
two steps into a single function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
To reduce the number of lines of data in the OMAP portion of the Linux
code base, subsequent patches will remove the lists of hwmod
interconnect links from the static hwmod data. These lists will be
built dynamically during boot. To ease this transition, this patch
centralizes the way that interconnect links are iterated into a single
function, _fetch_next_ocp_if().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Most IP blocks on the OMAP SoC have an interconnect link that is
intended to be used by the MPU to communicate with the IP block.
Several parts of the hwmod code need to be able to identify this link.
Currently, this is open-coded. However, future patches will change
the way that interconnect links are represented and will make
identifying the link more complex. So to avoid code duplication, this
patch centralizes the MPU port link identification code into a new
function, _find_mpu_rt_port().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Some hwmods were commented out from the OMAP4 data, under the theory
that they shouldn't be added until drivers were ready. But part of
the utility of the hwmod code is that it can reset and properly
initialize IP blocks that have no drivers associated with them.
Rather than commenting the links in the future hwmod data conversion
patches, discussing this with Benoit, it seems best to simply
uncomment them now.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
One of the OMAP4 links was missing OCP_USER flags, since it was only
used by the DSP initiator, and we did not have an OCP_USER_DSP flag.
Future patches will switch the hwmod code and data to register
interfaces, rather than hwmods, and it will be mandatory for all
interfaces to have at least one user bit set. This patch resolves the
issue by adding OCP_USER_DSP and marking the DSP-IVA interface
appropriately.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Commit 407a6888f7 ("OMAP4: hwmod data:
Add AESS, McPDM, bandgap, counter_32k, MMC, KBD, ISS & IPU") adds a
hwmod for the bandgap die temperature sensor IP block. This IP block
has no interconnect port or firewall region, nor does it have an
independent register space or OCP control registers. Its registers
are embedded in the System Control Module (SCM) IP block. So it
appears that the bandgap device should be created by the SCM driver.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
GPTIMER12 is attached to the L4 SEC interconnect, not directly to L4 WKUP.
Add the L4 SEC interconnect and attach GPTIMER12 to it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 hwmod data was missing a DSS->L3 interconnect link for the
OMAP3430 ES1 DSS hwmod. Since the hwmod code and data is being modified
to register interfaces rather than hwmods, this would result in the DSS hwmod
not being registered correctly on OMAP3430ES1.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit a52e2ab66d ("ARM: OMAP3: hwmod
data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1")
didn't link the MMC hwmods to the interconnects correctly. Future
patches will register hwmods by interface, so if this is not fixed,
the MMC IP blocks won't be registered. Update the interface data
records to point to the correct IP blocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the 2xxx and 3xxx hwmod data files use the old naming style
for hwmods, ending in a "_hwmod". These names are used by the OMAP
integration code to map hwmods to platform_devices, so they need to be
consistent, or the platform_devices won't be created. Remove the
_hwmod suffix to conform with the rest of the OMAP SoC data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
arch/arm/mach-omap2/timer.c pokes around inside the hwmod data
structures. Since the hwmod data structures are about to change, this
code will break. This patch modifies the timer code to use
recently-added hwmod functions instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
The timer integration code pokes around in hwmod data structures.
Those data structures are about to change. Define a function,
omap_hwmod_get_resource_byname(), for the timer integration code to
use instead.
The original patch has been changed to use struct resource by Tony's
request, although the caller of this function should not be a driver._
Platform drivers should get their data through the regular platform_*
functions; DT drivers through the appropriate of_* functions. This a
function is only for use by OMAP core code in arch/arm/*omap*.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
A subsequent patch will need to know the struct omap_hwmod_addr_space
record corresponding to the module's register target, used by the MPU.
So, convert _find_mpu_rt_base() into _find_mpu_rt_addr_space(). Then
modify its sole current user, _populate_mpu_rt_base(), to extract the
MPU RT base address itself from the struct omap_hwmod_addr_space record.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Change the way that hardreset lines are handled by the hwmod code.
Hardreset lines are generally associated with initiator IP blocks.
Prior to this change, the hwmod code expected to control hardreset
lines itself, asserting them on shutdown and deasserting them upon
enable. But driver authors inside TI have commented to us that their
drivers require direct control over these lines. Unfortunately, these
drivers haven't been posted publicly yet, so it's hard to determine
exactly what is needed, a priori. This change attempts to set forth
some reasonable semantics that should be an improvement over the
current code.
The semantics implemented by this patch are as follows:
- If the hwmod is not marked with HWMOD_INIT_NO_RESET, then assert all
associated hardreset lines during IP block setup. This is intended
to place the IP blocks into a known state that will not interfere
with other devices during kernel boot.
- IP blocks with hardreset lines will not be automatically enabled or
idled during setup. Instead, they will be left in the INITIALIZED
state.
- When the hwmod code is asked to enable, idle, or shutdown an IP
block with asserted hardreset lines, the hwmod code will do nothing.
The driver integration code must do the remaining work needed to
control these IP blocks. Once this driver integration code is posted
to the lists, hopefully we can consolidate it and move it inside the
hwmod code.
Custom reset functions for IP blocks with hardreset lines still should
be supported and are strongly endorsed. It is intended that every
subsystem with hardreset lines should have a custom reset function
that can place their subsystem into quiescent idle with the hardreset
lines deasserted.
This reverts most of commit 5365efbe29
("OMAP: hwmod: Add hardreset management support"). Later code
reorganizations caused the sequencing of the code from this patch to
be changed, anyway.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Reorganize the code involved in resetting and configuring an IP block
to make it easier to read and maintain. This involves improving
documentation, splitting some large functions up into smaller ones to
better conform with Documentation/CodingStyle, and removing some
unnecessary code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Reorganize the code involved in initializing the internal data for
each hwmod to make it easier to read and maintain. This involves
improving documentation and removing some duplicated and unnecessary
code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Revise the IP block reset process. This patch ensures that the
OCP_SYSCONFIG registers are reloaded after a custom reset. Since
OCP_SYSCONFIG bits are cleared during reset, they should be
reprogrammed unless the IP block is being left in reset. (The only IP
blocks that are left in reset are IP blocks with hardreset lines and
no custom reset function.) If the IP block is left in reset, then it
is inaccessible to the MPU, and an access to the OCP_SYSCONFIG
register will cause an abort.
This version incorporates comments from Omar Ramirez Luna
<omar.ramirez@ti.com> to skip the OCP_SYSCONFIG access after asserting
hardreset lines. This allows the MMU (IOMMU) IP block, which has
both hardreset lines and an OCP_SYSCONFIG register.
Also, ignore _ocp_softreset() errors if the IP block doesn't include a
softreset bit. This is needed since a subsequent patch will start
taking the return value of the _reset() function seriously.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Revert one softreset regression and few other minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WQ2B
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fix regression for bad uart muxing and oops when PM is not set.
Revert one softreset regression and few other minor fixes.
* tag 'omap-fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: DMTIMER: fix broken timer clock source selection
ARM: OMAP: serial: Fix the ocp smart idlemode handling bug
ARM: OMAP2+: UART: Fix incorrect population of default uart pads
ARM: OMAP: sram: fix BUG in dpll code for !PM case
ARM: OMAP2/3: VENC hwmods: Remove OCPIF_SWSUP_IDLE flag from VENC slave interface
ARM: OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status"
ARM: OMAP2+: hwmod: add softreset delay field and OMAP4 data
ARM: OMAP1: mux: add missing include
Remove the pseudo-hwmods associated with hardreset lines from the
OMAP4 data file. Future patches will convert this data to register
hwmods by interfaces, rather than registering hwmods directly. The
pseudo-hwmods aren't associated with any interfaces, so this will
create a problem.
After this change, the hwmod code will reset processor IPs at the
hwmod level, rather than by individual hardreset lines. So, for
example, if the IVA device driver code wishes to place one of the
sequencer cores into reset, while leaving the other active, it must do
so itself by calling the appropriate PRM functions.
This patch will cause a change in the initialization behavior of the
DSP, IVA, and IPU.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Parts of the hwmod code test to see if a module has one and only one
hardreset line before taking an action. It seems more appropriate
to control all hardreset lines associated with a hwmod, not just one.
It so happens that with the current hwmod data, this patch will not
change any behavior, since hwmods with hardreset lines have only one
hardreset line associated with them, and 'pseudo-hwmods' are used to
handle the other hardreset lines. But future hwmod data patches to
remove the pseudo-hwmods will change this.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Currently the errata is populated based on cpu checks this can
be removed and replaced with module version check of uart ip block.
MVR reg is provided within the uart reg map use the same
to populate the errata and thus now errata population and handling
can be managed within the driver itself.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arch/arm/mach-omap1, arch/arm/mach-omap2, and arch/arm/plat-omap.
Fixes all but one sparse warning and most of the useful
cppcheck warnings (excepting the warnings generated by the
dmtimer integration code which is going up via 3.4-rc fixes)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QdMB
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-a2-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into cleanup-sparse
Resolve static analysis warnings generated by files in
arch/arm/mach-omap1, arch/arm/mach-omap2, and arch/arm/plat-omap.
Fixes all but one sparse warning and most of the useful
cppcheck warnings (excepting the warnings generated by the
dmtimer integration code which is going up via 3.4-rc fixes)
Resolve some warnings identified by cppcheck in arch/arm/mach-omap2:
[arch/arm/mach-omap2/usb-tusb6010.c:129]: (style) Checking if unsigned variable 'tmp' is less than zero.
[arch/arm/mach-omap2/prm_common.c:241]: (error) Possible null pointer dereference: irq_setup - otherwise it is redundant to check if irq_setup is null at line 247
[arch/arm/mach-omap2/pm34xx.c:790]: (style) Variable 'per_clkdm' is assigned a value that is never used
[arch/arm/mach-omap2/pm34xx.c:790]: (style) Variable 'core_clkdm' is assigned a value that is never used
[arch/arm/mach-omap2/pm24xx.c:185]: (style) Variable 'only_idle' is assigned a value that is never used
[arch/arm/mach-omap2/mux.c:254]: (error) Possible null pointer dereference: mux
[arch/arm/mach-omap2/mux.c:258]: (error) Possible null pointer dereference: mux
[arch/arm/mach-omap2/gpmc-onenand.c:178]: (style) Variable 'tick_ns' is assigned a value that is never used
[arch/arm/mach-omap2/gpio.c:56]: (error) Possible null pointer dereference: pdata - otherwise it is redundant to check if pdata is null at line 57
[arch/arm/mach-omap2/devices.c:45]: (style) Variable 'l' is assigned a value that is never used
[arch/arm/mach-omap2/board-omap3evm.c:641] -> [arch/arm/mach-omap2/board-omap3evm.c:639]: (style) Found duplicate branches for if and else.
[arch/arm/mach-omap2/am35xx-emac.c:95]: (style) Variable 'regval' is assigned a value that is never used
[arch/arm/mach-omap2/devices.c:74]: (style) Variable 'l' is assigned a value that is never used
[arch/arm/mach-omap2/pm34xx.c:277]: (style) Variable 'per_prev_state' is assigned a value that is never used
[arch/arm/plat-omap/dmtimer.c:352]: (error) Possible null pointer dereference: timer - otherwise it is redundant to check if timer is null at line 354
[arch/arm/plat-omap/omap_device.c:478]: (style) Variable 'c' is assigned a value that is never used
[arch/arm/plat-omap/usb.c:42]: (style) Variable 'status' is assigned a value that is never used
[arch/arm/mach-omap1/clock.c:197]: (style) Variable 'dpll1_rate' is assigned a value that is never used
[arch/arm/mach-omap1/lcd_dma.c:60]: (style) struct or union member 'lcd_dma_info::size' is never used
[arch/arm/mach-omap1/pm.c:572]: (style) Variable 'entry' is assigned a value that is never used
Some of them are pretty good catches, such as gpio.c:56 and
usb-tusb6010.c:129.
Thanks to Jarkko Nikula for some comments on the sscanf() warnings.
It seems that the kernel sscanf() ignores the field width anyway for the
%d format, so those changes have been dropped from this second version.
Thanks to Daniel Marjamäki <daniel.marjamaki@gmail.com> for pointing
out that a variable was unnecessarily marked static in the
board-omap3evm.c change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Charulatha Varadarajan <charu@ti.com>
Cc: Daniel Marjamäki <daniel.marjamaki@gmail.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Charulatha Varadarajan <charu@ti.com> # for gpio.c
The current serial UART code, while fidling with ocp idlemode bits,
forget about the smart idle wakeup bit even if it is supported by
UART IP block. This will lead to missing the module wakeup on OMAP's
where the smart idle wakeup is supported.
This was the root cause of the console sluggishness issue, I have been
observing on OMAP4 devices and also can be potential reason for some
other UART wakeup issues.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit (7496ba3 ARM: OMAP2+: UART: Add default mux for all uarts)
wrongly added muxing of default pads for all uarts. This causes
breakage on multiple boards using uart pins for alternate functions.
For example, on zoom3 random oopses can be seen with nfsroot as
the smsc911x ethernet FIFO timings on GPMC bus are controlled
by gpmc_wait2 and gpmc_wait3 pins. This means we can't mux these
pads to uart4 functionality as commit 7496ba3 was doing.
Not all boards tend to use all uarts and most of unused uart pins
are muxed for other purpose. This commit breaks the modules which
where trying to use unused uart pins on their boards.
So remove the default pad muxing. Note that this is not a complete
fix, as we now rely on bootloader set muxing for the uart wake-up
events. Further patching is needed to enable wake-up events for
uarts that are already muxed to uart mode.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Russ Dill <russ.dill@gmail.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated comments to describe oops on zoom3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables. Remove it.
Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.
Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
sparse warns when 0 is passed to a function expecting a pointer argument.
Resolve these warnings by replacing the 0 with NULL.
arch/arm/plat-omap/include/plat/dmtimer.h:319:34: warning: Using plain integer as NULL pointer
arch/arm/plat-omap/include/plat/dmtimer.h:324:35: warning: Using plain integer as NULL pointer
arch/arm/mach-omap2/irq.c:294:22: warning: Using plain integer as NULL pointer
arch/arm/mach-omap1/board-palmz71.c:292:50: warning: Using plain integer as NULL pointer
arch/arm/mach-omap1/board-palmz71.c:295:73: warning: Using plain integer as NULL pointer
arch/arm/mach-omap1/ams-delta-fiq.c:105:63: warning: Using plain integer as NULL pointer
Signed-off-by: Paul Walmsley <paul@pwsan.com>
arch/arm/mach-omap2/gpmc.c passes a return value from ioremap() as the
fifth argument to request_irq() without casting it. This causes
sparse to generate the following warning:
arch/arm/mach-omap2/gpmc.c:759:63: warning: incorrect type in argument 5 (different address spaces)
arch/arm/mach-omap2/gpmc.c:759:63: expected void *dev
arch/arm/mach-omap2/gpmc.c:759:63: got void [noderef] <asn:2>*static [toplevel] [assigned] gpmc_base
It turns out that it's not necessary to pass this. gpmc_base is a
file-scoped static variable, the ISR is located in the same file ... and
the ISR doesn't even touch the passed-in variable. So, just replace it with
NULL in request_irq().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Several C files in arch/arm/mach-omap* and arch/arm/plat-omap declare
functions that are used by other files, but don't include the header
file where the prototype is declared. This results in the following
warnings from sparse:
arch/arm/mach-omap2/irq.c:114:5: warning: symbol 'omap_irq_pending' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:186:13: warning: symbol 'omap2_init_irq' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:191:13: warning: symbol 'omap3_init_irq' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:196:13: warning: symbol 'ti81xx_init_irq' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:233:39: warning: symbol 'omap2_intc_handle_irq' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:242:6: warning: symbol 'omap_intc_save_context' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:265:6: warning: symbol 'omap_intc_restore_context' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:291:6: warning: symbol 'omap3_intc_suspend' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:297:6: warning: symbol 'omap3_intc_prepare_idle' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:306:6: warning: symbol 'omap3_intc_resume_idle' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:312:39: warning: symbol 'omap3_intc_handle_irq' was not declared. Should it be static?
arch/arm/mach-omap2/omap-secure.c:59:12: warning: symbol 'omap_secure_ram_reserve_memblock' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-display.c:133:13: warning: symbol 'zoom_display_init' was not declared. Should it be static?
arch/arm/plat-omap/common.c:73:13: warning: symbol 'omap_init_consistent_dma_size' was not declared. Should it be static?
arch/arm/mach-omap1/irq.c:61:5: warning: symbol 'omap_irq_flags' was not declared. Should it be static?
arch/arm/mach-omap1/irq.c:179:13: warning: symbol 'omap1_init_irq' was not declared. Should it be static?
arch/arm/mach-omap1/reset.c:11:6: warning: symbol 'omap1_restart' was not declared. Should it be static?
Fix by including the appropriate header files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Senthilvadivu Guruswamy <svadivu@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Several function declarations used only in the files in which they're
declared should include the static keyword, but don't:
arch/arm/mach-omap2/serial.c:248:6: warning: symbol 'cmdline_find_option' was not declared. Should it be static?
arch/arm/mach-omap2/omap-wakeupgen.c:259:6: warning: symbol 'irq_sar_clear' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:878:27: warning: symbol 'rx51_vibra_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:882:27: warning: symbol 'rx51_audio_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:201:29: warning: symbol 'omap_panda_wlan_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:393:24: warning: symbol 'omap4_panda_dvi_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:403:12: warning: symbol 'omap4_panda_dvi_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:464:6: warning: symbol 'omap4_panda_display_init' was not declared. Should it be static?
arch/arm/mach-omap2/hsmmc.c:434:6: warning: symbol 'omap_init_hsmmc' was not declared. Should it be static?
arch/arm/mach-omap2/hwspinlock.c:31:12: warning: symbol 'hwspinlocks_init' was not declared. Should it be static?
arch/arm/mach-omap1/timer.c:58:12: warning: symbol 'omap1_dm_timer_init' was not declared. Should it be static?
arch/arm/mach-omap1/fpga.c:90:6: warning: symbol 'innovator_fpga_IRQ_demux' was not declared. Should it be static?
Mark all of these as static.
Thanks to Arnd Bergmann <arnd@arndb.de> for pointing out a typo in the
original patch description.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Govindraj R <govindraj.raja@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: David Anders <x0132446@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The clocks for all DSS slave interfaces were recently changed to "dss_ick" on
OMAP2 and OMAP3, this clock can be autoidled by PRCM. The VENC interface
previously had "dss_54m_fck" as it's clock which couldn't be autoidled, and
hence the OCPIF_SWSUP_IDLE flag was needed.
Remove the OCPIF_SWSUP_IDLE flag from VENC interfaces as it's clock is
now "dss_ick". This allows the PRCM hardware to autoidle the VENC
interface clocks when they are not active, rather than relying on the
software to do it, which can keep the interface clocks active
unnecessarily.
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: add a short description of the fix to the commit log]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This reverts commit f9a2f9c3fa. This
commit caused a regression in the I2C hwmod reset on OMAP2/3/4,
logging messages similar to these during boot:
[ 0.200378] omap_hwmod: i2c1: softreset failed (waited 10000 usec)
[ 0.222076] omap_hwmod: i2c2: softreset failed (waited 10000 usec)
While the original patch was intended to fix some reset-related timing
issues, it's believed that these problems were actually fixed by
commit 2800852a07 ("ARM: OMAP2+: hwmod:
Restore sysc after a reset"):
http://marc.info/?l=linux-arm-kernel&m=133410322617245&w=2
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Due to HW limitation, some IPs should not be accessed just after a
softreset. Since the current hwmod sequence is accessing the sysconfig
register just after the reset, it might lead to OCP bus error in
that case.
Add a new field in the sysconfig structure to specify a delay in usecs
needed after doing a softreset.
In the case of the ISS and FDIF modules, the L3 OCP port will be
disconnected upon a SW reset. That issue was confirmed with HW simulation
and an errata should be available soon. The HW recommendation to avoid
that is to wait for 100 OCP clk cycles, before accessing the IP.
Considering the worse case (OPP50), the L3 bus will run at 100 MHz,
so a 1 usec delay is needed. Add an x2 margin to be safe.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: dropped FDIF change for now since the hwmod data is not
yet upstream; the FDIF change will need to be added later once the FDIF
data is merged]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
A bunch of fixes for regressions (and a few other problems) in 3.4-rc1:
* Fix for regression of mach/io.h cleanup on platforms with PCI or PCMCIA
(adding back the include file on those for now)
* AT91 fixes for usb and spi
* smsc911x ethernet fixes for i.MX
* smsc911x fixes for OMAP
* gpio fixes for Tegra
* A handful of build error and warning fixes for various platforms
* cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series, aren't
technically regressions for 3.4, but they're valid fixes and we're still
relatively early in the rc cycle so it seems appropriate to include them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RVTD
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC fixes: from Olof Johansson:
"A bunch of fixes for regressions (and a few other problems) in
3.4-rc1:
- Fix for regression of mach/io.h cleanup on platforms with PCI or
PCMCIA (adding back the include file on those for now)
- AT91 fixes for usb and spi
- smsc911x ethernet fixes for i.MX
- smsc911x fixes for OMAP
- gpio fixes for Tegra
- A handful of build error and warning fixes for various platforms
- cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series,
aren't technically regressions for 3.4, but they're valid fixes and
we're still relatively early in the rc cycle so it seems appropriate
to include them."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: fix __io macro for PCMCIA
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
EXYNOS: fix dependency for EXYNOS_CPUFREQ
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
...
early v3.4-rc series. Also contains an HSMMC integration refinement
of an earlier hardware bug workaround.
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
ARM: OMAP AM3517/3505: clock data: change EMAC clocks aliases
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP: clock: fix race in disable all clocks
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3xxx: clock data: fix DPLL4 CLKSEL masks
ARM: OMAP3xxx: HSMMC: avoid erratum workaround when transceiver is attached
ARM: OMAP44xx: clockdomain data: correct the emu_sys_clkdm CLKTRCTRL data
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPfWEKAAoJEMePsQ0LvSpLGqIP/1Mvc3O7+Gs97E8BBR7RVkPC
Uo4aM6NMwkCBozC9XLooS12FFCC1k97aLh7IeEhN5qZ8U/FqkF6qIdMTLzJpSsnD
nuL1JLZGAdd+OtxgbVhjd/3cmK2H94K5XozZrKbC2/fypjDRjh40yk6hIH0zvZU6
+OX6r0kRW9HX6gC2+cAPJzKWaSgVimh6KQxRsevL8xbyPm183/vx2U0E1bicsHrY
rSXcQTo0AanDHNX4bSG3lMXiv+hVxYRpzlhJ1ToPN/fRokWXJjp3oycRYVL4A6KE
8MvvSORhf6yVekB+LOESIEmFNisGl/2zuAPFnZBnHzcpvNTvDB57uSPtUeQjXsUK
6MBgW5okGUU9tihP7m8tmP6kbo0tPdZRtBiJP0KDBflLRFAOgrcWiRQL+8jjus0v
ktHt6h3P71D8MoYN74T6x2/0NP49FXA3RVxuKDoaT3nXXkR7IvVNVXPh15zRTPFe
liTrn0U1Bu34HvpAuR8WRO5W0VgT2DTPQNk7WtZkYlyS1WXLAunDW9+Bv1JHS1MH
zeBZf6SNE1kVLWdNkFaYK0pAXHw8epwsUKeI9ZNIX3y9qdamzvafzeKQUjewPbLm
26KOzr3cuwIb7No7sh3fSpJV/Y8YFPCb9MvvzMg5yhfYf2SL4xYrudhSPcCw9gEy
2pCChl33o4AvxjkUEXjZ
=41FI
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a2-for-3.4rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
OMAP clock, powerdomain, clockdomain, and hwmod fixes intended for the
early v3.4-rc series. Also contains an HSMMC integration refinement
of an earlier hardware bug workaround.
* tag 'omap-fixes-a2-for-3.4rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
ARM: OMAP AM3517/3505: clock data: change EMAC clocks aliases
ARM: OMAP: clock: fix race in disable all clocks
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
ARM: OMAP3xxx: clock data: fix DPLL4 CLKSEL masks
ARM: OMAP3xxx: HSMMC: avoid erratum workaround when transceiver is attached
ARM: OMAP44xx: clockdomain data: correct the emu_sys_clkdm CLKTRCTRL data
omap_hwmod_softreset() does not seem to wait for reset status
after doing a softreset. Make it use _ocp_softreset() instead
which does this correctly.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After a softreset, make sure the sysc settings are correctly
restored.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
[paul@pwsan.com: combined post-reset SYSCONFIG reload code into the
_reset() function to avoid duplication and future mistakes]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some modules doesn't have SYSC_HAS_ENAWAKEUP bit available (ex: usb
host uhh module) in absence of this flag
omap_hwmod_enable/disable_wakeup avoids configuring pad mux wakeup
capability.
Configure sysc if SYSC_HAS_ENAWAKEUP is available and for other cases
try enabling/disabling wakeup from mux_pad pins.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[paul@pwsan.com: updated function kerneldoc documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Several clocks are missing clockdomains. This can cause problems with
the hwmod and power management code. Fill these in.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Matt Porter <mporter@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
All DPLLs except USB are in ALWON powerdomain. Make sure the
clkdm/pwrdm for USB DPLL (l3init) is turned on before attempting
a DPLL relock. So, mark the database accordingly.
Without this fix, it was seen that DPLL relock fails while testing
relock in a loop of USB DPLL.
Cc: Nishanth Menon <nm@ti.com>
Tested-by: Ameya Palande <ameya.palande@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b1cbdb00d ("OMAP: clockdomain: Wait for powerdomain to be ON
when using clockdomain force wakeup") was assuming that
pwrdm_state_switch() does wait for the powerdomain transition which is
not the case. The missing wait for the powerdomain transition
violates the sequence which the hardware expects, which causes power
management failures on some devices.
Fix this API by adding the pwrdm_wait_transition().
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: added some more details in the commit log]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rename EMAC clocks to match driver expectations: both davinci_emac and
davinci_mdio drivers call clk_get(dev, NULL) so we have to provide
("davinci_emac", NULL) and ("davinci_mdio.0", NULL) clocks instead of
("davinci_emac", "emac_clk") and ("davinci_emac", "phy_clk") resp.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Pull ARM fixes from Russell King:
"Nothing too big here, just small fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix more fallout from 9f97da78bf (Disintegrate asm/system.h for ARM)
ARM: fix bios32.c build warning
ARM: 7337/1: ptrace: fix ptrace_read_user for !CONFIG_MMU platforms
ARM: fix missing bug.h include in arch/arm/kernel/insn.c
ARM: sa11x0: fix build errors from DMA engine API updates
CLKS signal for McBSP ports can be selected from internal (PRCM) or
external (ABE_CLKS pin) source. To be able to use existing code we
need to create clock aliases consistent among OMAP2/3/4.
Based on a patch from Péter Ujfalusi <peter.ujfalusi@ti.com>;
the patch description above is his.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Commit 2a9f5a4d45 "OMAP3 clock: remove unnecessary duplicate of dpll4_m2_ck,
added for 36xx" consolidated dpll4 clock structures between 34xx and 36xx,
but left 34xx CLKSEL masks for most dpll4 related clocks, which causes
clock code to not behave correctly when booting on DM3730 with higher
(36xx only) divisors set:
[ 0.000000] WARNING: at arch/arm/mach-omap2/clkt_clksel.c:375 omap2_init_clksel_parent+0x104/0x114()
[ 0.000000] clock: dpll4_m3_ck: init parent: could not find regval 0
[ 0.000000] WARNING: at arch/arm/mach-omap2/clkt_clksel.c:194 omap2_clksel_recalc+0xd4/0xe4()
[ 0.000000] clock: Could not find fieldval 0 for clock dpll4_m3_ck parent dpll4_ck
Fix this by switching to 36xx masks, as valid divisors will be limited
by clksel_rate lists.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
If transceiver is attached to a MMC host of ES2.1 OMAP35xx, it seems
2.1.1.128 erratum doesn't apply and there is no data corruption,
probably because of different signal timing. The workaround for this
erratum disables multiblock reads, which causes dramatic loss of
performance (over 75% slower), so avoid it when transceiver is present.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
[paul@pwsan.com: edited commit message slightly]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 4430 ES2.0 TRM vX Table 3-744 "CM_EMU_CLKSTCTRL",
the emu_sys clockdomain data in mainline is incorrect.
The emu_sys clockdomain does not support the DISABLE_AUTO state, and
instead it supports the FORCE_WAKEUP state.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Fix the below section mismatch warning and alike:
WARNING: vmlinux.o(.text+0x281d4): Section mismatch in reference from
the function setup_ehci_io_mux() to the function
.init.text:omap_mux_init_signal()
The function setup_ehci_io_mux() references
the function __init omap_mux_init_signal().
This is often because setup_ehci_io_mux lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize fixed regulators in the board files. Trying to
do this in a generic way in gpmc-smsc911x.c gets messy as
the regulator may be provided by drivers, such as twl4030,
for some boards.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: combined into one patch, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding in support for regulators here creates several headaches.
- Boards that declare their own regulator cannot use this function.
- Multiple calls to this function require special handling.
- Boards that declare id's other than '0' need special handling.
Now that there is a simple regulator_register_fixed, we can push
this registration back into the board files.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looking back into git history, this code was never used and was
probably left over from a copy/paste.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If this function is called the first time with flags set, and the
second time without flags set then the leftover flags from the first
called will be used rather than the desired default flags.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This seems to be a leftover from when gpmc-smsc911x.c was copied
from gpmc-smc91x.c.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/kernel/io.c: In function '_memcpy_toio':
arch/arm/kernel/io.c:29: error: implicit declaration of function 'outer_sync'
arch/arm/mach-omap2/omap_l3_noc.c: In function 'l3_interrupt_handler':
arch/arm/mach-omap2/omap_l3_noc.c💯 error: implicit declaration of function 'outer_sync'
kernel/irq/generic-chip.c: In function 'irq_gc_mask_disable_reg':
kernel/irq/generic-chip.c:45: error: implicit declaration of function 'outer_sync'
kernel/sched/rt.c: In function 'rt_set_overload':
kernel/sched/rt.c:248: error: implicit declaration of function 'outer_sync'
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ACPI & Power Management changes from Len Brown:
- ACPI 5.0 after-ripples, ACPICA/Linux divergence cleanup
- cpuidle evolving, more ARM use
- thermal sub-system evolving, ditto
- assorted other PM bits
Fix up conflicts in various cpuidle implementations due to ARM cpuidle
cleanups (ARM at91 self-refresh and cpu idle code rewritten into
"standby" in asm conflicting with the consolidation of cpuidle time
keeping), trivial SH include file context conflict and RCU tracing fixes
in generic code.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (77 commits)
ACPI throttling: fix endian bug in acpi_read_throttling_status()
Disable MCP limit exceeded messages from Intel IPS driver
ACPI video: Don't start video device until its associated input device has been allocated
ACPI video: Harden video bus adding.
ACPI: Add support for exposing BGRT data
ACPI: export acpi_kobj
ACPI: Fix logic for removing mappings in 'acpi_unmap'
CPER failed to handle generic error records with multiple sections
ACPI: Clean redundant codes in scan.c
ACPI: Fix unprotected smp_processor_id() in acpi_processor_cst_has_changed()
ACPI: consistently use should_use_kmap()
PNPACPI: Fix device ref leaking in acpi_pnp_match
ACPI: Fix use-after-free in acpi_map_lsapic
ACPI: processor_driver: add missing kfree
ACPI, APEI: Fix incorrect APEI register bit width check and usage
Update documentation for parameter *notrigger* in einj.txt
ACPI, APEI, EINJ, new parameter to control trigger action
ACPI, APEI, EINJ, limit the range of einj_param
ACPI, APEI, Fix ERST header length check
cpuidle: power_usage should be declared signed integer
...
This is a first pass of some of the merge window fallout for ARM platforms.
Nothing controversial:
* A system.h fallout fix for OMAP
* PXA fixes for breakage caused by the regulator struct changes
* GPIO fixes for OMAP to properly deal with dynamic IRQ allocation
* A mismerge in our arm-soc tree of an lpc32xx change for networking
* A fix for USB setup on tegra
* An undo of __init annotation of display mux setup on OMAP that's needed
at runtime
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=36Eb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Olof Johansson:
"This is a first pass of some of the merge window fallout for ARM
platforms.
Nothing controversial:
- A system.h fallout fix for OMAP
- PXA fixes for breakage caused by the regulator struct changes
- GPIO fixes for OMAP to properly deal with dynamic IRQ allocation
- A mismerge in our arm-soc tree of an lpc32xx change for networking
- A fix for USB setup on tegra
- An undo of __init annotation of display mux setup on OMAP that's
needed at runtime"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: pxa: fix build issue on stargate2
ARM: pxa: fix build issue on cm-x300
ARM: pxa: fix build failure for regulator consumer in em-x270.c
ARM: LPC32xx: clock.c: Fix lpc-eth clock reference
ARM: OMAP: pm: fix compilation break
ARM: OMAP: Remove OMAP_GPIO_IRQ macro definition
drivers: input: Fix OMAP_GPIO_IRQ with gpio_to_irq() in ams_delta_serio_exit()
ARM: OMAP: boards: Fix OMAP_GPIO_IRQ usage with gpio_to_irq()
ARM: pxa: fix regulator related build fail in magician_defconfig
ARM: tegra: Fix device tree AUXDATA for USB/EHCI
ARM: OMAP2+: Remove __init from DSI mux functions
Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes,
moving some of the oft-repeated macros to a common location and removing a bunch of
boiler plate. This is another step closer to a common zImage for multiple platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIsn
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
From Tony Lindgren:
"This contains the updated gpio_to_irq patches from Tarun, and a trivial
build fix from Govindraj to #include <asm/system_misc.h> in pm.c.
The DSI mux patch is the same."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: pm: fix compilation break
ARM: OMAP: Remove OMAP_GPIO_IRQ macro definition
drivers: input: Fix OMAP_GPIO_IRQ with gpio_to_irq() in ams_delta_serio_exit()
ARM: OMAP: boards: Fix OMAP_GPIO_IRQ usage with gpio_to_irq()
ARM: OMAP2+: Remove __init from DSI mux functions
Fix the compilation break observed on latest mainline caused
by 9f97da78 (Disintegrate asm/system.h for ARM):
arch/arm/mach-omap1/pm.c: In function 'omap_pm_prepare':
arch/arm/mach-omap1/pm.c:587: error: implicit declaration of function 'disable_hlt'
arch/arm/mach-omap1/pm.c: In function 'omap_pm_finish':
arch/arm/mach-omap1/pm.c:624: error: implicit declaration of function 'enable_hlt'
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:681: error: 'arm_pm_idle' undeclared (first use in this function)
...
arch/arm/mach-omap2/pm.c: In function 'omap_pm_begin':
arch/arm/mach-omap2/pm.c:239: error: implicit declaration of function 'disable_hlt'
arch/arm/mach-omap2/pm.c: In function 'omap_pm_end':
arch/arm/mach-omap2/pm.c:247: error: implicit declaration of function 'enable_hlt'
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated to fix omap1 too]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The following commits change gpio-omap to use dynamic
IRQ allocation:
25db711 gpio/omap: Fix IRQ handling for SPARSE_IRQ
384ebe1 gpio/omap: Add DT support to GPIO driver
With dynamic allocation of IRQ the usage of OMAP_GPIO_IRQ
is no longer valid. We must be using gpio_to_irq() instead.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
