commit 53914b6799 had the
same message. That commit did put everything in place but
did not make can_proto const itself.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
First, make callers pass on-stack flowi4 to ip_route_output_gre()
so they can get at the fully resolved flow key.
Next, use that in ipgre_tunnel_xmit() to avoid the need to use
rt->rt_{dst,src}.
Signed-off-by: David S. Miller <davem@davemloft.net>
PCIe connections should be expressed as GT/s (GigaTransfers per second)
instead of the current Gb/s (Gigabits per second). In addition, it is
incorrect because (due to PCIe gen 1 & 2 having a 20% overhead) the
actually data rate, when expressed in Gb/s, is only 80% of the rate of
GT/s.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce buffered read/writes which greatly improves performance on
parts with large EEPROMs.
Previously reading/writing a word requires taking/releasing of synchronization
semaphores which adds 10ms to each operation. The optimization is to
read/write in buffers, but make sure the semaphore is not held for >500ms
according to the datasheet.
Since we can't read the EEPROM page size ixgbe_detect_eeprom_page_size() is
used to discover the EEPROM size when needed and keeps the result in
word_page_size for the rest of the run time.
Use buffered reads for ethtool -e.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
warning: symbol 'before' shadows an earlier one
Convert large macros to functions similar to e1000e.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correcting a simple typo with enabling software defined pins. I don't
believe this was causing any issues but this is how it was meant to be
implemented.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change remaining direct calls to function pointers.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device lies about supporting phys_id. Remove it and just
let the upper layer report not supported.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent commits have changed how EEPROM size is checked and if the size
word is misconfigured, the driver will fail to load. This patch adds a
check for invalid size word in the EEPROM and uses default size instead
for 82576 parts.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch sent by Stephen Hemminger.
This version incorporates the ethtool changes that Bruce Allan
submitted.
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Instead of rt->rt_{dst,src}
The only tricky part is source route option handling.
If the source route option is enabled we can't just use plain 'daddr',
we have to use opt->opt.faddr.
Signed-off-by: David S. Miller <davem@davemloft.net>
In function 'e100_hw_init':
warning: 'err' may be used uninitialized in this function
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix kconfig unmet dependency warning: HAVE_BPF_JIT depends on NET, so
make the "select" of it depend on NET also.
warning: (X86) selects HAVE_BPF_JIT which has unmet direct dependencies (NET)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To more accurately reflect that it is purely a routing
cache lookup key and is used in no other context.
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac.h uses struct platform_device and doesn't include
<linux/platform_device.h>. Whereas drivers/net/stmmac/stmmac.h includes it, but
doesn't directly use it. And so we get following compilation warning while using
this file:
warning: ‘struct platform_device’ declared inside parameter list
This patch includes <linux/platform_device.h> in linux/stmmac.h and removes it
from drivers/net/stmmac/stmmac.h
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four years ago, Patrick made a change to hold rtnl mutex during netlink
dump callbacks.
I believe it was a wrong move. This slows down concurrent dumps, making
good old /proc/net/ files faster than rtnetlink in some situations.
This occurred to me because one "ip link show dev ..." was _very_ slow
on a workload adding/removing network devices in background.
All dump callbacks are able to use RCU locking now, so this patch does
roughly a revert of commits :
1c2d670f36 : [RTNETLINK]: Hold rtnl_mutex during netlink dump callbacks
6313c1e099 : [RTNETLINK]: Remove unnecessary locking in dump callbacks
This let writers fight for rtnl mutex and readers going full speed.
It also takes care of phonet : phonet_route_get() is now called from rcu
read section. I renamed it to phonet_route_get_rcu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slow path output route resolution always makes sure that
->{saddr,daddr} are set, and also if we trigger into IPSEC resolution
we initialize them as well, because xfrm_lookup() expects them to be
fully resolved.
But if we hit the fast path and flowi4->flowi4_proto is zero, we won't
do this initialization.
Therefore, move the IPSEC path initialization to the route cache
lookup fast path to make sure these are always set.
Signed-off-by: David S. Miller <davem@davemloft.net>
The rcu protected macros rcu_dereference() and rcu_assign_pointer()
for the bat_priv->primary_if need to be used, as well as spin/rcu locking.
Otherwise we might end up using a primary_if pointer pointing to already
freed memory.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This is a regression from c4aac1ab9b
- gw_node_update() doesn't add a new gw_node in case of empty curr_gw.
This means that at the beginning no gw_node is added, leading to an
empty gateway list.
- gw_election() is terminating in case of curr_gw == NULL. It has to
terminate in case of curr_gw != NULL
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
atomic_dec_not_zero() is very useful and it is currently defined
multiple times. So it is possible to move it in main.h
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
orig_hash_find() manages rcu_lock/unlock internally and doesn't need to
be surrounded by rcu_read_lock() / rcu_read_unlock() anymore
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Acked-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This makes sure that one cannot request a 99Mbps full-duplex and get a
100Mbps half-duplex configuration in return due to the way the
speed/duplex parameters are handled internally.
Tested: e1000 works
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial driver reported different speeds depending on the port being
used. This advertises the speed to be 10Mbps in any case, which is
what it actually is on the wire.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tells the NIC to take the speed specified by ethtool into account
when configuring the NIC, instead of keeping the previous speed.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().
All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'ep' argument of ethtool_cmd_speed is not altered: advertise it in
protoype. +Indentation fix. Also add comments to advise using the
ethtool_cmd_speed API to get/set the link speed.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable setting speed and auto negotiation parameters for GbE ports.
Hardware do not support half duplex setting currently.
o Update driver version to 5.0.17.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Support ethtool command ETHTOOL_GCHANNELS and ETHTOOL_SCHANNELS.
o Number of rcv rings configuration depend upon number of msix vector.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For backward compatibility, we should retain the module parameters and
sysfs attributes to control the number of peer notifications
(gratuitous ARPs and unsolicited NAs) sent after bonding failover.
Also, it is possible for failover to take place even though the new
active slave does not have link up, and in that case the peer
notification should be deferred until it does.
Change ipv4 and ipv6 so they do not automatically send peer
notifications on bonding failover.
Change the bonding driver to send separate NETDEV_NOTIFY_PEERS
notifications when the link is up, as many times as requested. Since
it does not directly control which protocols send notifications, make
num_grat_arp and num_unsol_na aliases for a single parameter. Bump
the bonding version number and update its documentation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pktgen doesn't generate number of frags requested.
Divide packet size by number of frags and fill that in every frags.
Example:
With packet size 1470, it generate only 11 frags. Initial frags
get lenght 706, 353, 177....so on. Last frag get divided by 2.
Now with this fix, each frags will get 78 bytes.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_alloc() and module_free() are available only if CONFIG_MODULES=y
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: David S. Miller <davem@davemloft.net>
