vxlan driver has bypass for local vxlan traffic, but that
depends on information about all VNIs on local system in
vxlan driver. This is not available in case of LWT.
Therefore following patch disable encap bypass for LWT
vxlan traffic.
Fixes: ee122c79d4 ("vxlan: Flow based tunneling").
Reported-by: Jakub Libosvar <jlibosva@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LWT user can specify destination as well as source ip address
for given tunnel endpoint. But vxlan is ignoring given source
ip address. Following patch uses both ip address to route the
tunnel packet. This consistent with other LWT implementations,
like GENEVE and GRE.
Fixes: ee122c79d4 ("vxlan: Flow based tunneling").
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
Few BPF helper related checksum fixes
The set contains three fixes with regards to CHECKSUM_COMPLETE
and BPF helper functions. For details please see individual
patches.
Thanks!
v1 -> v2:
- Fixed make htmldocs issue reported by kbuild bot.
- Rest as is.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When having skbs on ingress with CHECKSUM_COMPLETE, tc BPF programs don't
push rcsum of mac header back in and after BPF run back pull out again as
opposed to some other subsystems (ovs, for example).
For cases like q-in-q, meaning when a vlan tag for offloading is already
present and we're about to push another one, then skb_vlan_push() pushes the
inner one into the skb, increasing mac header and skb_postpush_rcsum()'ing
the 4 bytes vlan header diff. Likewise, for the reverse operation in
skb_vlan_pop() for the case where vlan header needs to be pulled out of the
skb, we're decreasing the mac header and skb_postpull_rcsum()'ing the 4 bytes
rcsum of the vlan header that was removed.
However mangling the rcsum here will lead to hw csum failure for BPF case,
since we're pulling or pushing data that was not part of the current rcsum.
Changing tc BPF programs in general to push/pull rcsum around BPF_PROG_RUN()
is also not really an option since current behaviour is ABI by now, but apart
from that would also mean to do quite a bit of useless work in the sense that
usually 12 bytes need to be rcsum pushed/pulled also when we don't need to
touch this vlan related corner case. One way to fix it would be to push the
necessary rcsum fixup down into vlan helpers that are (mostly) slow-path
anyway.
Fixes: 4e10df9a60 ("bpf: introduce bpf_skb_vlan_push/pop() helpers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_skb_store_bytes() invocations above L2 header need BPF_F_RECOMPUTE_CSUM
flag for updates, so that CHECKSUM_COMPLETE will be fixed up along the way.
Where we ran into an issue with bpf_skb_store_bytes() is when we did a
single-byte update on the IPv6 hoplimit despite using BPF_F_RECOMPUTE_CSUM
flag; simple ping via ICMPv6 triggered a hw csum failure as a result. The
underlying issue has been tracked down to a buffer alignment issue.
Meaning, that csum_partial() computations via skb_postpull_rcsum() and
skb_postpush_rcsum() pair invoked had a wrong result since they operated on
an odd address for the hoplimit, while other computations were done on an
even address. This mix doesn't work as-is with skb_postpull_rcsum(),
skb_postpush_rcsum() pair as it always expects at least half-word alignment
of input buffers, which is normally the case. Thus, instead of these helpers
using csum_sub() and (implicitly) csum_add(), we need to use csum_block_sub(),
csum_block_add(), respectively. For unaligned offsets, they rotate the sum
to align it to a half-word boundary again, otherwise they work the same as
csum_sub() and csum_add().
Adding __skb_postpull_rcsum(), __skb_postpush_rcsum() variants that take the
offset as an input and adapting bpf_skb_store_bytes() to them fixes the hw
csum failures again. The skb_postpull_rcsum(), skb_postpush_rcsum() helpers
use a 0 constant for offset so that the compiler optimizes the offset & 1
test away and generates the same code as with csum_sub()/_add().
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up to commit f8ffad69c9 ("bpf: add skb_postpush_rcsum and fix
dev_forward_skb occasions") to fix an issue for dev_queue_xmit() redirect
locations which need CHECKSUM_COMPLETE fixups on ingress.
For the same reasons as described in f8ffad69c9 already, we of course
also need this here, since dev_queue_xmit() on a veth device will let us
end up in the dev_forward_skb() helper again to cross namespaces.
Latter then calls into skb_postpull_rcsum() to pull out L2 header, so
that netif_rx_internal() sees CHECKSUM_COMPLETE as it is expected. That
is, CHECKSUM_COMPLETE on ingress covering L2 _payload_, not L2 headers.
Also here we have to address bpf_redirect() and bpf_clone_redirect().
Fixes: 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper")
Fixes: 27b29f6305 ("bpf: add bpf_redirect() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call site for this function appears as:
#ifdef DEBUG
data->msg_enable = DEBUG;
dump_eth_one(dev);
#endif
...leading to the following warning for !DEBUG builds:
drivers/net/ethernet/tundra/tsi108_eth.c:169:13: warning: 'dump_eth_one' defined but not used [-Wunused-function]
static void dump_eth_one(struct net_device *dev)
^
...when using the arch/powerpc/configs/mpc7448_hpc2_defconfig
Put the function definition under the same #ifdef as the call site
to avoid the warning.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: DCB fixes
Patches 1 and 2 fix a problem in which PAUSE frames settings are wrongly
overridden when ieee_setpfc() gets called.
Patch 3 adds a missing rollback in port's creation error path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We correctly execute mlxsw_sp_port_dcb_fini() when port is removed, but
I missed its rollback in the error path of port creation, so add it.
Fixes: f00817df2b ("mlxsw: spectrum: Introduce support for Data Center Bridging (DCB)")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PFCC register is used to configure both PAUSE and PFC frames.
Therefore, when PFC frames are disabled we must make sure we don't
mistakenly also disable PAUSE frames (which might be enabled).
Fix this by packing the PFCC register with the current PAUSE settings.
Note that this register is also accessed via ethtool ops, but there we
are guaranteed to have PFC disabled.
Fixes: d81a6bdb87 ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ieee_setpfc() gets called, PAUSE frames are not necessarily
disabled on the port.
Check if PAUSE frames are disabled or enabled and configure the port's
headroom buffer accordingly.
Fixes: d81a6bdb87 ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like a simple copy'n'paste error.
Fixes: 1aa661f5c3 ("rhashtable-test: Measure time to insert, remove & traverse entries")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter says:
====================
sctp_diag: A bunch of fixes for upcoming 'ss' support
The following series contains a number of fixes necessary to make my yet
unpublished 'ss' support patch functional.
Changes since v1:
- Fixed patch 2/3
- Rebased whole series onto current net-next/master
Changes since v2:
- Improved description of patch 2/3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 'ss' always adds TCPF_CLOSE to idiag_states flags, sctp_diag can't
rely upon TCPF_LISTEN flag solely being present when listening sockets
are requested.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The asoc's timer value is not kept in asoc->timeouts array but in it's
primary transport instead.
Furthermore, we must export the timer only if it is pending, otherwise
the value will underrun when stored in an unsigned variable and
user space will only see a very large timeout value.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is required to correctly interpret INET_DIAG_INFO messages exported
by sctp_diag module.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
USRIO and JUMBO CAPS have the same mask.
Fix the same.
Fixes: ce721a7021 ("net: ethernet: cadence-macb: Add disabled usrio caps")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix 80+80 bandwidth warning
* fix powersave with mac80211 TXQ implementation
* use correct way to free SKBs from multicast buffering
* mesh: fix operation ordering to work with all drivers
* mesh: end service period even when peer goes away
* mesh: correct HT opmode validity checks
* pass hw pointer from mac80211 to driver in TPT method,
fixing a bug (in a bit the wrong way, but that's what
we have right now)
-----BEGIN PGP SIGNATURE-----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=4hWm
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
First set of fixes for the current cycle:
* fix 80+80 bandwidth warning
* fix powersave with mac80211 TXQ implementation
* use correct way to free SKBs from multicast buffering
* mesh: fix operation ordering to work with all drivers
* mesh: end service period even when peer goes away
* mesh: correct HT opmode validity checks
* pass hw pointer from mac80211 to driver in TPT method,
fixing a bug (in a bit the wrong way, but that's what
we have right now)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
increase test coverage to check previously missing 'update when full'
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The introduction of pre-allocated hash elements inadvertently broke
the behavior of bpf hash maps where users expected to call
bpf_map_update_elem() without considering that the map can be full.
Some programs do:
old_value = bpf_map_lookup_elem(map, key);
if (old_value) {
... prepare new_value on stack ...
bpf_map_update_elem(map, key, new_value);
}
Before pre-alloc the update() for existing element would work even
in 'map full' condition. Restore this behavior.
The above program could have updated old_value in place instead of
update() which would be faster and most programs use that approach,
but sometimes the values are large and the programs use update()
helper to do atomic replacement of the element.
Note we cannot simply update element's value in-place like percpu
hash map does and have to allocate extra num_possible_cpu elements
and use this extra reserve when the map is full.
Fixes: 6c90598174 ("bpf: pre-allocate hash map elements")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):
drivers/net/dsa/b53/b53_common.c: In function ‘b53_arl_read’:
drivers/net/dsa/b53/b53_common.c:1072: warning: integer constant is too large for ‘long’ type
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inside the kafs filesystem it is possible to occasionally have a call
processed and terminated before we've had a chance to check whether we need
to clean up the rx queue for that call because afs_send_simple_reply() ends
the call when it is done, but this is done in a workqueue item that might
happen to run to completion before afs_deliver_to_call() completes.
Further, it is possible for rxrpc_kernel_send_data() to be called to send a
reply before the last request-phase data skb is released. The rxrpc skb
destructor is where the ACK processing is done and the call state is
advanced upon release of the last skb. ACK generation is also deferred to
a work item because it's possible that the skb destructor is not called in
a context where kernel_sendmsg() can be invoked.
To this end, the following changes are made:
(1) kernel_rxrpc_data_consumed() is added. This should be called whenever
an skb is emptied so as to crank the ACK and call states. This does
not release the skb, however. kernel_rxrpc_free_skb() must now be
called to achieve that. These together replace
rxrpc_kernel_data_delivered().
(2) kernel_rxrpc_data_consumed() is wrapped by afs_data_consumed().
This makes afs_deliver_to_call() easier to work as the skb can simply
be discarded unconditionally here without trying to work out what the
return value of the ->deliver() function means.
The ->deliver() functions can, via afs_data_complete(),
afs_transfer_reply() and afs_extract_data() mark that an skb has been
consumed (thereby cranking the state) without the need to
conditionally free the skb to make sure the state is correct on an
incoming call for when the call processor tries to send the reply.
(3) rxrpc_recvmsg() now has to call kernel_rxrpc_data_consumed() when it
has finished with a packet and MSG_PEEK isn't set.
(4) rxrpc_packet_destructor() no longer calls rxrpc_hard_ACK_data().
Because of this, we no longer need to clear the destructor and put the
call before we free the skb in cases where we don't want the ACK/call
state to be cranked.
(5) The ->deliver() call-type callbacks are made to return -EAGAIN rather
than 0 if they expect more data (afs_extract_data() returns -EAGAIN to
the delivery function already), and the caller is now responsible for
producing an abort if that was the last packet.
(6) There are many bits of unmarshalling code where:
ret = afs_extract_data(call, skb, last, ...);
switch (ret) {
case 0: break;
case -EAGAIN: return 0;
default: return ret;
}
is to be found. As -EAGAIN can now be passed back to the caller, we
now just return if ret < 0:
ret = afs_extract_data(call, skb, last, ...);
if (ret < 0)
return ret;
(7) Checks for trailing data and empty final data packets has been
consolidated as afs_data_complete(). So:
if (skb->len > 0)
return -EBADMSG;
if (!last)
return 0;
becomes:
ret = afs_data_complete(call, skb, last);
if (ret < 0)
return ret;
(8) afs_transfer_reply() now checks the amount of data it has against the
amount of data desired and the amount of data in the skb and returns
an error to induce an abort if we don't get exactly what we want.
Without these changes, the following oops can occasionally be observed,
particularly if some printks are inserted into the delivery path:
general protection fault: 0000 [#1] SMP
Modules linked in: kafs(E) af_rxrpc(E) [last unloaded: af_rxrpc]
CPU: 0 PID: 1305 Comm: kworker/u8:3 Tainted: G E 4.7.0-fsdevel+ #1303
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
Workqueue: kafsd afs_async_workfn [kafs]
task: ffff88040be041c0 ti: ffff88040c070000 task.ti: ffff88040c070000
RIP: 0010:[<ffffffff8108fd3c>] [<ffffffff8108fd3c>] __lock_acquire+0xcf/0x15a1
RSP: 0018:ffff88040c073bc0 EFLAGS: 00010002
RAX: 6b6b6b6b6b6b6b6b RBX: 0000000000000000 RCX: ffff88040d29a710
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff88040d29a710
RBP: ffff88040c073c70 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: ffff88040be041c0 R15: ffffffff814c928f
FS: 0000000000000000(0000) GS:ffff88041fa00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa4595f4750 CR3: 0000000001c14000 CR4: 00000000001406f0
Stack:
0000000000000006 000000000be04930 0000000000000000 ffff880400000000
ffff880400000000 ffffffff8108f847 ffff88040be041c0 ffffffff81050446
ffff8803fc08a920 ffff8803fc08a958 ffff88040be041c0 ffff88040c073c38
Call Trace:
[<ffffffff8108f847>] ? mark_held_locks+0x5e/0x74
[<ffffffff81050446>] ? __local_bh_enable_ip+0x9b/0xa1
[<ffffffff8108f9ca>] ? trace_hardirqs_on_caller+0x16d/0x189
[<ffffffff810915f4>] lock_acquire+0x122/0x1b6
[<ffffffff810915f4>] ? lock_acquire+0x122/0x1b6
[<ffffffff814c928f>] ? skb_dequeue+0x18/0x61
[<ffffffff81609dbf>] _raw_spin_lock_irqsave+0x35/0x49
[<ffffffff814c928f>] ? skb_dequeue+0x18/0x61
[<ffffffff814c928f>] skb_dequeue+0x18/0x61
[<ffffffffa009aa92>] afs_deliver_to_call+0x344/0x39d [kafs]
[<ffffffffa009ab37>] afs_process_async_call+0x4c/0xd5 [kafs]
[<ffffffffa0099e9c>] afs_async_workfn+0xe/0x10 [kafs]
[<ffffffff81063a3a>] process_one_work+0x29d/0x57c
[<ffffffff81064ac2>] worker_thread+0x24a/0x385
[<ffffffff81064878>] ? rescuer_thread+0x2d0/0x2d0
[<ffffffff810696f5>] kthread+0xf3/0xfb
[<ffffffff8160a6ff>] ret_from_fork+0x1f/0x40
[<ffffffff81069602>] ? kthread_create_on_node+0x1cf/0x1cf
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a94efbd7cc ("ethernet: arc: emac_main: add missing of_node_put
after calling of_parse_phandle") added missing of_node_put after calling
of_parse_phandle, but missing the devm_ioremap_resource() error handling
case.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_device->ndo_set_rx_headroom (introduced in
871b642ade) says
"Setting a negtaive value reset the rx headroom
to the default value".
It seems that the OVS implementation in
3a927bc7cf overlooked this and sets
dev->needed_headroom unconditionally.
This doesn't have an immediate effect, but can mess up later
LL_RESERVED_SPACE calculations, such as done in
net/ipv6/mcast.c:mld_newpack. For reference, this issue was found
from a skb_panic raised there after the length calculations had given
the wrong result.
Note the other current users of this interface
(drivers/net/tun.c:tun_set_headroom and
drivers/net/veth.c:veth_set_rx_headroom) are both checking this
correctly thus need no modification.
Thanks to Ben for some pointers from the crash dumps!
Cc: Benjamin Poirier <bpoirier@suse.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1361414
Signed-off-by: Ian Wienand <iwienand@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.
This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[rewrite commit message, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, NL80211_MESHCONF_HT_OPMODE validation rejected correct
flag combinations, e.g. IEEE80211_HT_OP_MODE_PROTECTION_NONHT_MIXED |
IEEE80211_HT_OP_MODE_NON_HT_STA_PRSNT.
Doing just a range-check allows setting flags that don't exist (0x8)
and invalid flag combinations.
Implements some checks based on IEEE 802.11 2012 8.4.2.59 "HT
Operation element".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[reword commit message, simplify a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If QoS frame with EOSP (end of service period) subfield=1 sent by local
peer was not acked by remote peer, local peer did not end the MPSP. This
prevents local peer from going to DOZE state. And if the remote peer
goes away without closing connection, local peer continues AWAKE state
and wastes battery.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Manish Chopra says:
====================
qlcnic: bug fixes
This series fixes a data structure corruption bug in
VF's async mailbox commands handling and an issue realted
to napi poll budget in the driver.
Please consider applying this series to "net"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver modifies the supplied NAPI budget in qlcnic_83xx_msix_tx_poll()
function. Instead, it should use the budget as it is.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a data structure corruption bug in the SRIOV VF mailbox
handler code. While handling mailbox commands from the atomic context,
driver is accessing and updating qlcnic_async_work_list_struct entry fields
in the async work list. These fields could be concurrently accessed by the
work function resulting in data corruption.
This patch restructures async mbx command handling by using a separate
async command list instead of using a list of work_struct structures.
A single work_struct is used to schedule and handle the async commands
with proper locking mechanism.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siva Reddy Kallam says:
====================
tg3: Disallow 0 rx coalesce time and correctly report RSS queues in tg3_get_rxnfc
First patch:
Diasllow rx coalescing time to be 0
Second patch:
Report the correct number of RSS queues through tg3_get_rxnfc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove the wrong substraction from info->data in
tg3_get_rxnfc function. Without this patch, the number of RSS
queues reported is less by one.
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the rx coalescing time is 0, interrupts
are not generated from the controller and rx path hangs.
To avoid this rx hang, updating the driver to not allow
rx coalescing time to be 0.
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using per-register incrementing ID can lead to
find_good_pkt_pointers() confusing registers which
have completely different values. Consider example:
0: (bf) r6 = r1
1: (61) r8 = *(u32 *)(r6 +76)
2: (61) r0 = *(u32 *)(r6 +80)
3: (bf) r7 = r8
4: (07) r8 += 32
5: (2d) if r8 > r0 goto pc+9
R0=pkt_end R1=ctx R6=ctx R7=pkt(id=0,off=0,r=32) R8=pkt(id=0,off=32,r=32) R10=fp
6: (bf) r8 = r7
7: (bf) r9 = r7
8: (71) r1 = *(u8 *)(r7 +0)
9: (0f) r8 += r1
10: (71) r1 = *(u8 *)(r7 +1)
11: (0f) r9 += r1
12: (07) r8 += 32
13: (2d) if r8 > r0 goto pc+1
R0=pkt_end R1=inv56 R6=ctx R7=pkt(id=0,off=0,r=32) R8=pkt(id=1,off=32,r=32) R9=pkt(id=1,off=0,r=32) R10=fp
14: (71) r1 = *(u8 *)(r9 +16)
15: (b7) r7 = 0
16: (bf) r0 = r7
17: (95) exit
We need to get a UNKNOWN_VALUE with imm to force id
generation so lines 0-5 make r7 a valid packet pointer.
We then read two different bytes from the packet and
add them to copies of the constructed packet pointer.
r8 (line 9) and r9 (line 11) will get the same id of 1,
independently. When either of them is validated (line
13) - find_good_pkt_pointers() will also mark the other
as safe. This leads to access on line 14 being mistakenly
considered safe.
Fixes: 969bf05eb3 ("bpf: direct packet access")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with -Wmaybe-uninitialized shows a potential use of
an uninitialized variable:
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_phy_connect':
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:802:23: warning: 'phy_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
Although the compiler correctly identified this based on the function,
the current code is still safe as long dev->of_node is non-NULL
for the case of CONFIG_ACPI=n, which is currently the case.
The warning is now disabled by default, but still appears when
building with W=1, and other build test tools should be able to
detect it as well. Adding an #else clause here makes the code
more robust and makes it clear to the compiler that this cannot
happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 8089a96f60 ("drivers: net: xgene: Add backward compatibility")
Signed-off-by: David S. Miller <davem@davemloft.net>
ovs_ct_find_existing() issues a warning if an existing conntrack entry
classified as IP_CT_NEW is found, with the premise that this should
not happen. However, a newly confirmed, non-expected conntrack entry
remains IP_CT_NEW as long as no reply direction traffic is seen. This
has resulted into somewhat confusing kernel log messages. This patch
removes this check and warning.
Fixes: 289f2253 ("openvswitch: Find existing conntrack entry after upcall.")
Suggested-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
. Move the suppressing of the __builtin_return_address >0 warning to the
tracing directory only.
. metag recordmcount fix for newer glibc's
. Two tracing histogram fixes that were reported by KASAN
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXofc2AAoJEKKk/i67LK/8f7YIAI7YkUnzA7VZ/FmbgD+fu3MI
XmLLb98dzEOEHKEUrmv/9TSj/W6cTVfgVH2z/U89J6nbPj56GgMf03qL1wn9l/6s
kwxEt5GopmKwCdtnjGkLYZcg13OWottzmFoyn/koKCXFq7PwfGQdLzhwIQUpsXgG
MxOk1Iv9TbACzz4k5aG866yhJu6cWDRSdC3cfv7F4xn+Z3GWggzCpW7fknXy66cJ
iVsdUGZVz5O5jVJAFqzERZHBJQpraozjkKr3lprCdHuXa/EEAYQuuYG5WBxggYaQ
eJ1my2p5MKkxORz1Nk9cGuFa6DW35spn9+iOOyTt6sRU/8tijGxTPLNWtKfJcVQ=
=fbRU
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"A few updates and fixes:
- move the suppressing of the __builtin_return_address >0 warning to
the tracing directory only.
- metag recordmcount fix for newer glibc's
- two tracing histogram fixes that were reported by KASAN"
* tag 'trace-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix use-after-free in hist_register_trigger()
tracing: Fix use-after-free in hist_unreg_all/hist_enable_unreg_all
Makefile: Mute warning for __builtin_return_address(>0) for tracing only
ftrace/recordmcount: Work around for addition of metag magic but not relocations
With gcc < 4.2 (e.g. 4.1.2):
CC fs/proc/task_mmu.o
cc1: error: unrecognized command line option "-Wno-override-init"
To fix this, only enable the compiler option when it is actually
supported by the compiler.
Fixes: ca52953f5f ("fs/proc/task_mmu.c: suppress compilation warnings with W=1")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers (e.g. wl18xx) expect that the last stage in the
de-initialization process will be stopping the beacons, similar to AP flow.
Update ieee80211_stop_mesh() flow accordingly.
As peers can be removed dynamically, this would not impact other drivers.
Tested also on Ralink RT3572 chipset.
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge yet more updates from Andrew Morton:
- the rest of ocfs2
- various hotfixes, mainly MM
- quite a bit of misc stuff - drivers, fork, exec, signals, etc.
- printk updates
- firmware
- checkpatch
- nilfs2
- more kexec stuff than usual
- rapidio updates
- w1 things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
ipc: delete "nr_ipc_ns"
kcov: allow more fine-grained coverage instrumentation
init/Kconfig: add clarification for out-of-tree modules
config: add android config fragments
init/Kconfig: ban CONFIG_LOCALVERSION_AUTO with allmodconfig
relay: add global mode support for buffer-only channels
init: allow blacklisting of module_init functions
w1:omap_hdq: fix regression
w1: add helper macro module_w1_family
w1: remove need for ida and use PLATFORM_DEVID_AUTO
rapidio/switches: add driver for IDT gen3 switches
powerpc/fsl_rio: apply changes for RIO spec rev 3
rapidio: modify for rev.3 specification changes
rapidio: change inbound window size type to u64
rapidio/idt_gen2: fix locking warning
rapidio: fix error handling in mbox request/release functions
rapidio/tsi721_dma: advance queue processing from transfer submit call
rapidio/tsi721: add messaging mbox selector parameter
rapidio/tsi721: add PCIe MRRS override parameter
rapidio/tsi721_dma: add channel mask and queue size parameters
...
This allows OrangeFS to utilize the dcache and adds an in kernel
attribute cache. We previously used the user side client for this
purpose.
We see a modest performance increase on small file operations. For
example, without the cache, compiling coreutils takes about 17 minutes.
With the patch and a 50 millisecond timeout for dcache_timeout_msecs and
getattr_timeout_msecs (the default), compiling coreutils takes about
6 minutes 20 seconds. On the same hardware, compiling coreutils on an
xfs filesystem takes 90 seconds. We see similar improvements with mdtest
and a test involving writing, reading, and deleting a large number of
small files.
Interested parties can review more data at the following URL.
https://docs.google.com/spreadsheets/d/1v4aUeppKexIbRMz_Yn9k4eaM3uy2KCaPoe_93YKWOtA/pubhtml
The eventual goal of this is to allow getdents to turn into a
readdirplus to the OrangeFS server. The cache will be filled then, which
should provide a performance benefit to the common case of readdir
followed by getattr on each entry (i.e. ls -l).
This also fixes a bug. When orangefs_inode_permission was added, it did
not collect i_size from the OrangeFS server, since this presses an
unnecessary load on the OrangeFS server. However, it left a case where
i_size is never initialized. Then running an executable could fail.
With this patch, size is always collected to be inserted into the cache.
Thus the bug disappears. If this patch is not accepted during this merge
window, we will send a one-line band-aid for this bug instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=rGmf
-----END PGP SIGNATURE-----
Merge tag 'for-linus-v4.8' of git://github.com/martinbrandenburg/linux
Pull orangefs update from Martin Brandenburg:
"Kernel side caching and executable bugfix
This allows OrangeFS to utilize the dcache and adds an in kernel
attribute cache. We previously used the user side client for this
purpose.
We see a modest performance increase on small file operations. For
example, without the cache, compiling coreutils takes about 17
minutes. With the patch and a 50 millisecond timeout for
dcache_timeout_msecs and getattr_timeout_msecs (the default),
compiling coreutils takes about 6 minutes 20 seconds. On the same
hardware, compiling coreutils on an xfs filesystem takes 90 seconds.
We see similar improvements with mdtest and a test involving writing,
reading, and deleting a large number of small files.
Interested parties can review more data at the following URL.
https://docs.google.com/spreadsheets/d/1v4aUeppKexIbRMz_Yn9k4eaM3uy2KCaPoe_93YKWOtA/pubhtml
The eventual goal of this is to allow getdents to turn into a
readdirplus to the OrangeFS server. The cache will be filled then,
which should provide a performance benefit to the common case of
readdir followed by getattr on each entry (i.e. ls -l).
This also fixes a bug. When orangefs_inode_permission was added, it
did not collect i_size from the OrangeFS server, since this presses an
unnecessary load on the OrangeFS server. However, it left a case
where i_size is never initialized. Then running an executable could
fail.
With this patch, size is always collected to be inserted into the
cache. Thus the bug disappears. If this patch is not accepted during
this merge window, we will send a one-line band-aid for this bug
instead"
* tag 'for-linus-v4.8' of git://github.com/martinbrandenburg/linux:
Orangefs: update orangefs.txt
orangefs: Account for jiffies wraparound.
orangefs: Change default dcache and getattr timeout to 50 msec.
orangefs: Allow dcache and getattr cache time to be configured.
orangefs: Cache getattr results.
orangefs: Use d_time to avoid excessive lookups
* RADOS namespace support in libceph and CephFS (Zheng Yan and myself).
The stopgaps added in 4.5 to deny access to inodes in namespaces are
removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature bit is now fully
supported.
* A large rework of the MDS cap flushing code (Zheng Yan).
* Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU.
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJXoKLJAAoJEEp/3jgCEfOLDTUIAIcctpKUiNBokc95mQaXYl34
j7lPIaD0/Ur7JPt4nMdtlywYJYSVV2c+SglHztj/+fv0G4bWbLVEFRruh9SwKIci
PzttcmycIAqSn1f5gBZwyQbGuffd/F0EnBj7fFjcukt01i3s1ZQ7t4XtLGtAV0Ts
aIfFtx9SqWig57Z1OZqNgnhnOoh6IqNbic3FL5Hvdl5N5pFbBcQho6Vzoa5O1osH
URG6RmCcO4nykfSoxiivE7UZ+CImsXHkRD7rupBuIjqjZ8wvmZqQF5qxnkb9Dw2F
IkNhrHkTSIiv4EsNPLAETTnFSozrL1nEykKr2FBW+ti8nxNcav+8FgVapqLvFIw=
=gQ0/
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client
Pull Ceph updates from Ilya Dryomov:
"The highlights are:
- RADOS namespace support in libceph and CephFS (Zheng Yan and
myself). The stopgaps added in 4.5 to deny access to inodes in
namespaces are removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature
bit is now fully supported
- A large rework of the MDS cap flushing code (Zheng Yan)
- Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue"
* tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client: (34 commits)
ceph: fix symbol versioning for ceph_monc_do_statfs
ceph: Correctly return NXIO errors from ceph_llseek
ceph: Mark the file cache as unreclaimable
ceph: optimize cap flush waiting
ceph: cleanup ceph_flush_snaps()
ceph: kick cap flushes before sending other cap message
ceph: introduce an inode flag to indicates if snapflush is needed
ceph: avoid sending duplicated cap flush message
ceph: unify cap flush and snapcap flush
ceph: use list instead of rbtree to track cap flushes
ceph: update types of some local varibles
ceph: include 'follows' of pending snapflush in cap reconnect message
ceph: update cap reconnect message to version 3
ceph: mount non-default filesystem by name
libceph: fsmap.user subscription support
ceph: handle LOOKUP_RCU in ceph_d_revalidate
ceph: allow dentry_lease_is_valid to work under RCU walk
ceph: clear d_fsinfo pointer under d_lock
ceph: remove ceph_mdsc_lease_release
ceph: don't use ->d_time
...
For more targeted fuzzing, it's better to disable kernel-wide
instrumentation and instead enable it on a per-subsystem basis. This
follows the pattern of UBSAN and allows you to compile in the kcov
driver without instrumenting the whole kernel.
To instrument a part of the kernel, you can use either
# for a single file in the current directory
KCOV_INSTRUMENT_filename.o := y
or
# for all the files in the current directory (excluding subdirectories)
KCOV_INSTRUMENT := y
or
# (same as above)
ccflags-y += $(CFLAGS_KCOV)
or
# for all the files in the current directory (including subdirectories)
subdir-ccflags-y += $(CFLAGS_KCOV)
Link: http://lkml.kernel.org/r/1464008380-11405-1-git-send-email-vegard.nossum@oracle.com
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It doesn't trim just symbols that are totally unused in-tree - it trims
the symbols unused by any in-tree modules actually built. If you've
done a 'make localmodconfig' and only build a hundred or so modules,
it's pretty likely that your out-of-tree module will come up lacking
something...
Hopefully this will save the next guy from a Homer Simpson "D'oh!"
moment.
Link: http://lkml.kernel.org/r/10177.1469787292@turing-police.cc.vt.edu
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Copy the config fragments from the AOSP common kernel android-4.4
branch. It is becoming possible to run mainline kernels with Android,
but the kernel defconfigs don't work as-is and debugging missing config
options is a pain. Adding the config fragments into the kernel tree,
makes configuring a mainline kernel as simple as:
make ARCH=arm multi_v7_defconfig android-base.config android-recommended.config
The following non-upstream config options were removed:
CONFIG_NETFILTER_XT_MATCH_QTAGUID
CONFIG_NETFILTER_XT_MATCH_QUOTA2
CONFIG_NETFILTER_XT_MATCH_QUOTA2_LOG
CONFIG_PPPOLAC
CONFIG_PPPOPNS
CONFIG_SECURITY_PERF_EVENTS_RESTRICT
CONFIG_USB_CONFIGFS_F_MTP
CONFIG_USB_CONFIGFS_F_PTP
CONFIG_USB_CONFIGFS_F_ACC
CONFIG_USB_CONFIGFS_F_AUDIO_SRC
CONFIG_USB_CONFIGFS_UEVENT
CONFIG_INPUT_KEYCHORD
CONFIG_INPUT_KEYRESET
Link: http://lkml.kernel.org/r/1466708235-28593-1-git-send-email-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Cc: Rom Lemarchand <romlem@android.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
