Commit Graph

25 Commits

Author SHA1 Message Date
Kyeyoon Park
fa9ffc7456 cfg80211: Add support for QoS mapping
This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.

The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-19 16:29:22 +01:00
Andrei Otcheretianski
b176e62940 cfg80211: aggregate mgmt_tx parameters into a struct
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-02 11:51:52 +01:00
David Spinadel
fc73f11f5f cfg80211: add wdev to testmode cmd
To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-12 14:11:37 +02:00
Simon Wunderlich
16ef1fe272 nl80211/cfg80211: add channel switch command
To allow channel switch announcements within beacons, add
the channel switch command to nl80211/cfg80211. This is
implementation is intended for AP and (later) IBSS mode.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-01 18:30:28 +02:00
Simon Wunderlich
dcd6eac1f3 nl80211: add scan width to bss and scan request structs
To allow scanning and working with 5 MHz and 10 MHz BSS, extend the
inform bss commands and add wrappers to take 5 and 10 MHz bss into
account.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
2013-07-16 09:58:01 +03:00
Johannes Berg
6ff57cf888 cfg80211/mac80211: clean up cfg80211 SME APIs
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.

Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.

Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-04 13:03:10 +02:00
Johannes Berg
8d61ffa5e0 cfg80211/mac80211: use cfg80211 wdev mutex in mac80211
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.

Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-25 00:02:16 +02:00
Johannes Berg
a92eecbbea cfg80211: fix WoWLAN wakeup tracing
If the device reports a non-wireless wakeup reason, the
tracing code crashes trying to dereference a NULL pointer.
Fix this by checking the pointer on all accesses and also
add a non_wireless tag to the event.

Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-16 22:38:03 +02:00
Arend van Spriel
5de1798489 cfg80211: introduce critical protocol indication from user-space
Some protocols need a more reliable connection to complete
successful in reasonable time. This patch adds a user-space
API to indicate the wireless driver that a critical protocol
is about to commence and when it is done, using nl80211 primitives
NL80211_CMD_CRIT_PROTOCOL_START and NL80211_CRIT_PROTOCOL_STOP.

There can be only on critical protocol session started per
registered cfg80211 device.

The driver can support this by implementing the cfg80211 callbacks
.crit_proto_start() and .crit_proto_stop(). Examples of protocols
that can benefit from this are DHCP, EAPOL, APIPA. Exactly how the
link can/should be made more reliable is up to the driver. Things
to consider are avoid scanning, no multi-channel operations, and
alter coexistence schemes.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-22 15:48:00 +02:00
John W. Linville
9a574cd67a Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	net/mac80211/sta_info.c
	net/wireless/core.h
2013-03-29 16:41:36 -04:00
Johannes Berg
ce1eadda6b cfg80211: fix wdev tracing crash
Arend reported a crash in tracing if the driver returns an
ERR_PTR() value from the add_virtual_intf() callback. This
is due to the tracing then still attempting to dereference
the "pointer", fix this by using IS_ERR_OR_NULL().

Reported-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-20 22:21:31 +01:00
Vladimir Kondratiev
021fcdc13a cfg80211: fix inconsistency in trace for rdev_set_mac_acl
There is NETDEV_ENTRY that was incorrectly assigned as WIPHY_ASSIGN,
fix it.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-07 11:20:01 +01:00
Jouni Malinen
355199e02b cfg80211: Extend support for IEEE 802.11r Fast BSS Transition
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the WLAN
driver and NL80211_CMD_FT_EVENT to send FT events from the WLAN driver.
This will carry the target AP's MAC address along with the relevant
Information Elements. This event is used to report received FT IEs
(MDIE, FTIE, RSN IE, TIE, RICIE). These changes allow FT to be supported
with drivers that use an internal SME instead of user space option (like
FT implementation in wpa_supplicant with mac80211-based drivers).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-06 16:35:51 +01:00
Simon Wunderlich
04f39047af nl80211/cfg80211: add radar detection command/event
Add new NL80211_CMD_RADAR_DETECT, which starts the Channel
Availability Check (CAC). This command will also notify the
usermode about events (CAC finished, CAC aborted, radar
detected, NOP finished).
Once radar detection has started it should continuously
monitor for radars as long as the channel is active.

This patch enables DFS for AP mode in nl80211/cfg80211.

Based on original patch by Victor Goldenshtein <victorg@ti.com>

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
[remove WIPHY_FLAG_HAS_RADAR_DETECT again -- my mistake]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-15 09:40:18 +01:00
Johannes Berg
cd8f7cb4e6 cfg80211/mac80211: support reporting wakeup reason
When waking up from WoWLAN, it is useful to know
what triggered the wakeup. Support reporting the
wakeup reason(s) in cfg80211 (and a pass-through
in mac80211) to allow userspace to know.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31 14:00:21 +01:00
Vasanthakumar Thiagarajan
77765eaf5c cfg80211/nl80211: add API for MAC address ACLs
Add API to enable drivers to implement MAC address based
access control in AP/P2P GO mode. Capable drivers advertise
this capability by setting the maximum number of MAC
addresses in such a list in wiphy->max_acl_mac_addrs.

An initial ACL may be given to the NL80211_CMD_START_AP
command and/or changed later with NL80211_CMD_SET_MAC_ACL.

Black- and whitelists are supported, but not simultaneously.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
[rewrite commit log, many cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-25 18:36:44 +01:00
Johannes Berg
ec816087e8 cfg80211: fix some tracing output issues
In some cases, e.g. probe_status, there were spaces
missing so the trace output was confusing. Also make
it more like mac80211 when printing netdevs/wiphys
to make reading a combined log easier.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:48:17 +01:00
Johannes Berg
3d9d1d6656 nl80211/cfg80211: support VHT channel configuration
Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.

Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)

This also adds new helper functions:
 - cfg80211_chandef_create to create a channel def
   struct given the control channel and channel type,
 - cfg80211_chandef_identical to check if two channel
   definitions are identical
 - cfg80211_chandef_compatible to check if the given
   channel definitions are compatible, and return the
   wider of the two

This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
 - regulatory checks on the usable bandwidth (if that
   even makes sense)
 - regulatory TX power (database can't deal with it)
 - a proper channel compatibility calculation for the
   new channel types

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:59 +01:00
Johannes Berg
683b6d3b31 cfg80211: pass a channel definition struct
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.

Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:58 +01:00
Johannes Berg
42d97a599e cfg80211: remove remain-on-channel channel type
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.

Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:58 +01:00
Jouni Malinen
3475b0946b cfg80211: Add TDLS event to allow drivers to request operations
The NL80211_CMD_TDLS_OPER command was previously used only for userspace
request for the kernel code to perform TDLS operations. However, there
are also cases where the driver may need to request operations from
userspace, e.g., when using security on the AP path. Add a new cfg80211
function for generating a TDLS operation event for drivers to request a
new link to be set up (NL80211_TDLS_SETUP) or an existing link to be
torn down (NL80211_TDLS_TEARDOWN). Drivers can optionally use these
events, e.g., based on noticing data traffic being sent to a peer
station that is seen with good signal strength.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19 15:47:32 +01:00
Johannes Berg
c8442118ad cfg80211: allow per interface TX power setting
The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.

Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30 09:11:34 +01:00
Johannes Berg
eeb126e9ee cfg80211: add tracing for P2P Device start/stop
These were missed due to the tracing work having
started on a kernel that didn't have P2P Device
yet, implement them now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-23 19:52:53 +02:00
Beni Lev
4ee3e063f1 cfg80211: add cfg80211 exported function tracing
Also add tracing to the API functions that drivers
(and mac80211) can call in cfg80211.

Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-18 10:53:38 +02:00
Beni Lev
14e8a3c47e cfg80211: add tracing to rdev-ops
Add tracing to make debugging cfg80211/mac80211
(or full-mac driver) interaction easier.

Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Hila Gonen <hila.gonen@intel.com>
Tested-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[add a cast to int to sizeof() to avoid warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-18 10:53:37 +02:00