dn_fib_count_nhs() could enter an infinite loop if nhp->rtnh_len == 0
(i.e. if userspace passes a malformed netlink message).
Let's use the helpers from net/nexthop.h which take care of all this
stuff. We can do exactly the same as e.g. fib_count_nexthops() and
fib_get_nhs() from net/ipv4/fib_semantics.c.
This fixes the softlockup for me.
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the data plane is offloaded the traffic doesn't go through the
networking stack. Therefore, after first resolving a neighbour the NUD
state machine will transition it from REACHABLE to STALE until it's
finally deleted by the garbage collector.
To prevent such situations the offloading driver should notify the NUD
state machine on any neighbours that were recently used. The driver's
polling interval should be set so that the NUD state machine can
function as if the traffic wasn't offloaded.
Currently, there are no in-tree drivers that can report confirmation for
a neighbour, but only 'used' indication. Therefore, the polling interval
should be set according to DELAY_FIRST_PROBE_TIME, as a neighbour will
transition from REACHABLE state to DELAY (instead of STALE) if "a packet
was sent within the last DELAY_FIRST_PROBE_TIME seconds" (RFC 4861).
Send a netevent whenever the DELAY_FIRST_PROBE_TIME changes - either via
netlink or sysctl - so that offloading drivers can correctly set their
polling interval.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2 upper device needs to propagate neigh_construct/destroy calls down to
lower devices. Do this by defining default ndo functions and use them in
team, bond, bridge and vlan.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the following patch will allow upper devices to follow the call down
lower devices, we need to add dev here and not rely on n->dev.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is hard to unbind nf-logger:
echo NONE > /proc/sys/net/netfilter/nf_log/0
bash: echo: write error: No such file or directory
sysctl -w net.netfilter.nf_log.0=NONE
sysctl: setting key "net.netfilter.nf_log.0": No such file or directory
net.netfilter.nf_log.0 = NONE
You need explicitly send '\0', for instance like:
echo -e "NONE\0" > /proc/sys/net/netfilter/nf_log/0
That seem to be strange, so fix it using proc_dostring.
Now it works fine:
modprobe nfnetlink_log
echo nfnetlink_log > /proc/sys/net/netfilter/nf_log/0
cat /proc/sys/net/netfilter/nf_log/0
nfnetlink_log
echo NONE > /proc/sys/net/netfilter/nf_log/0
cat /proc/sys/net/netfilter/nf_log/0
NONE
v2: add missed error check for proc_dostring
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
- Cleanup work by Markus Pargmann and Sven Eckelmann (six patches)
- Initial Netlink support by Matthias Schiffer (two patches)
- Throughput Meter implementation by Antonio Quartulli, a kernel-space
traffic generator to estimate link speeds. This feature is useful on
low-end WiFi APs where running iperf or netperf from userspace
gives wrong results due to heavy userspace/kernelspace overhead.
(two patches)
- API clean-up work by Antonio Quartulli (one patch)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PFHu
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20160704' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- Cleanup work by Markus Pargmann and Sven Eckelmann (six patches)
- Initial Netlink support by Matthias Schiffer (two patches)
- Throughput Meter implementation by Antonio Quartulli, a kernel-space
traffic generator to estimate link speeds. This feature is useful on
low-end WiFi APs where running iperf or netperf from userspace
gives wrong results due to heavy userspace/kernelspace overhead.
(two patches)
- API clean-up work by Antonio Quartulli (one patch)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions that iterate over lower devices and find port device.
As a dependency add netdev_for_each_all_lower_dev and
netdev_for_each_all_lower_dev_rcu macro with
netdev_all_lower_get_next and netdev_all_lower_get_next_rcu shelpers.
Also, add functions to return mlxsw struct according to lower device
found and mlxsw_port struct with a reference to lower device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_pernet_subsys() fails, we shouldn't try to call
unregister_pernet_subsys().
Fixes: 467fa15356 ("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.")
Cc: stable@vger.kernel.org
Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_clear_hash() was invoked due to mangling of relevant headers and
BPF program needs skb->hash later on, we can add a helper to trigger hash
recalculation via bpf_get_hash_recalc().
The helper will return the newly retrieved hash directly, but later access
can also be done via skb context again through skb->hash directly (inline)
without needing to call the helper once more.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add another xmit_mode to pktgen to allow testing xmit functionality
of qdiscs. The new mode "queue_xmit" injects packets at
__dev_queue_xmit() so that qdisc is called.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extremely useful for setting packet type to host so i dont
have to modify the dst mac address using pedit (which requires
that i know the mac address)
Example usage:
tc filter add dev eth0 parent ffff: protocol ip pref 9 u32 \
match ip src 5.5.5.5/32 \
flowid 1:5 action skbedit ptype host
This will tag all packets incoming from 5.5.5.5 with type
PACKET_HOST
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The routing API data structure contains several function
pointers that can easily be grouped together based on the
component they work with.
Split the API in subobjects in order to improve definition readability.
At the same time, remove the "bat_" prefix from the API object and
its fields names. These are batman-adv private structs and there is no
need to always prepend such prefix, which only makes function invocations
much much longer.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The throughput meter module is a simple, kernel-space replacement for
throughtput measurements tool like iperf and netperf. It is intended to
approximate TCP behaviour.
It is invoked through batctl: the protocol is connection oriented, with
cumulative acknowledgment and a dynamic-size sliding window.
The test *can* be interrupted by batctl. A receiver side timeout avoids
unlimited waitings for sender packets: after one second of inactivity, the
receiver abort the ongoing test.
Based on a prototype from Edo Monticelli <montik@autistici.org>
Signed-off-by: Antonio Quartulli <antonio.quartulli@open-mesh.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Return the proper netdev TX status along the TX path so that the tp_meter
can understand when the queue is full and should stop sending packets.
Signed-off-by: Antonio Quartulli <antonio.quartulli@open-mesh.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
BATADV_CMD_GET_MESH_INFO is used to query basic information about a
batman-adv softif (name, index and MAC address for both the softif and
the primary hardif; routing algorithm; batman-adv version).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: Reduce the number of changes to
BATADV_CMD_GET_MESH_INFO, add missing kerneldoc, add policy for attributes]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
debugfs is currently severely broken virtually everywhere in the kernel
where files are dynamically added and removed (see
http://lkml.iu.edu/hypermail/linux/kernel/1506.1/02196.html for some
details). In addition to that, debugfs is not namespace-aware.
Instead of adding new debugfs entries, the whole infrastructure should be
moved to netlink. This will fix the long standing problem of large buffers
for debug tables and hard to parse text files.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: Strip down patch to only add genl family,
add missing kerneldoc]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
netfilter uses multiple FWINV #defines with identical form that hide a
specific structure variable and dereference it with a invflags member.
$ git grep "#define FWINV"
include/linux/netfilter_bridge/ebtables.h:#define FWINV(bool,invflg) ((bool) ^ !!(info->invflags & invflg))
net/bridge/netfilter/ebtables.c:#define FWINV2(bool, invflg) ((bool) ^ !!(e->invflags & invflg))
net/ipv4/netfilter/arp_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(arpinfo->invflags & (invflg)))
net/ipv4/netfilter/ip_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(ipinfo->invflags & (invflg)))
net/ipv6/netfilter/ip6_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(ip6info->invflags & (invflg)))
net/netfilter/xt_tcpudp.c:#define FWINVTCP(bool, invflg) ((bool) ^ !!(tcpinfo->invflags & (invflg)))
Consolidate these macros into a single NF_INVF macro.
Miscellanea:
o Neaten the alignment around these uses
o A few lines are > 80 columns for intelligibility
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add the commands to set and show the mode of SRIOV E-Switch, two modes
are supported:
* legacy: operating in the "old" L2 based mode (DMAC --> VF vport)
* switchdev: the E-Switch is referred to as whitebox switch configured
using standard tools such as tc, bridge, openvswitch etc. To allow
working with the tools, for each VF, a VF representor netdevice is
created by the E-Switch manager vendor device driver instance (e.g PF).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- two patches with minimal clean up work by Antonio Quartulli and
Simon Wunderlich
- eight patches of B.A.T.M.A.N. V, API and documentation clean
up work, by Antonio Quartulli and Marek Lindner
- Andrew Lunn fixed the skb priority adoption when forwarding
fragmented packets (two patches)
- Multicast optimization support is now enabled for bridges which
comes with some protocol updates, by Linus Luessing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=js/J
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20160701' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- two patches with minimal clean up work by Antonio Quartulli and
Simon Wunderlich
- eight patches of B.A.T.M.A.N. V, API and documentation clean
up work, by Antonio Quartulli and Marek Lindner
- Andrew Lunn fixed the skb priority adoption when forwarding
fragmented packets (two patches)
- Multicast optimization support is now enabled for bridges which
comes with some protocol updates, by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect use of nla_strlcpy() where the first NLA_HDRLEN bytes
of the link name where left out.
Making the output of tipc-config -ls look something like:
Link statistics:
dcast-link
1:data0-1.1.2:data0
1:data0-1.1.3:data0
Also, for the record, the patch that introduce this regression
claims "Sending the whole object out can cause a leak". Which isn't
very likely as this is a compat layer, where the data we are parsing
is generated by us and we know the string to be NULL terminated. But
you can of course never be to secure.
Fixes: 5d2be1422e (tipc: fix an infoleak in tipc_nl_compat_link_dump)
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS ping messages are sent with a non-zero src port to a zero
dst port, so that the rds pong messages can be sent back to the
originators src port. However if a confused/malicious sender
sends a ping with a 0 src port, we'd have an infinite ping-pong
loop. To avoid this, the receiver should ignore ping messages
with a 0 src port.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reconnecting, the peer with the smaller IP address will initiate
the reconnect, to avoid needless duelling SYN issues.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ->conn_path_connect callbacks in the rds_transport
that are used to set up a single connection path.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->sk_user_data contains a pointer to the rds_conn_path
for the socket. Use this consistently in the rds_tcp_data_ready
callbacks to get the rds_conn_path for rds_recv_incoming.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket callbacks should all operate on a struct rds_conn_path,
in preparation for a MP capable RDS-TCP.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single rds_connection may have multiple rds_conn_paths that have
to be carefully and correctly destroyed, for both rmmod and
netns-delete cases.
For both cases, we extract a single rds_tcp_connection for
each conn into a temporary list, and then invoke rds_conn_destroy()
which iteratively dismantles every path in the rds_connection.
For the netns deletion case, we additionally have to make sure
that we do not leave a socket in TIME_WAIT state, as this will
hold up the netns deletion. Thus we call rds_tcp_conn_paths_destroy()
to reset state quickly.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct rds_tcp_connection is the transport-specific private
data structure that tracks TCP information per rds_conn_path.
Modify this structure to have a back-pointer to the rds_conn_path
for which it is the ->cp_transport_data.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The c_passive bit is only intended for the IB transport and will
never be encountered in rds-tcp, so remove the dead logic that
predicates on this bit.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor code to avoid separate indirections for single-path
and multipath transports. All transports (both single and mp-capable)
will get a pointer to the rds_conn_path, and can trivially derive
the rds_connection from the ->cp_conn.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a bpf helper, bpf_skb_in_cgroup, to decide if a skb->sk
belongs to a descendant of a cgroup2. It is similar to the
feature added in netfilter:
commit c38c4597e4 ("netfilter: implement xt_cgroup cgroup2 path match")
The user is expected to populate a BPF_MAP_TYPE_CGROUP_ARRAY
which will be used by the bpf_skb_in_cgroup.
Modifications to the bpf verifier is to ensure BPF_MAP_TYPE_CGROUP_ARRAY
and bpf_skb_in_cgroup() are always used together.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 9b368814b3 ("net: fix bridge multicast packet checksum validation")
we need to fixup the checksum for CHECKSUM_COMPLETE when
pushing skb on RX path. Otherwise we get similar splats.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
People who use PACKET_FANOUT_HASH want a symmetric hash, meaning that
they want packets going in both directions on a flow to hash to the
same bucket.
The core kernel SKB hash became non-symmetric when the ipv6 flow label
and other entities were incorporated into the standard flow hash order
to increase entropy.
But there are no users of PACKET_FANOUT_HASH who want an assymetric
hash, they all want a symmetric one.
Therefore, use the flow dissector to compute a flat symmetric hash
over only the protocol, addresses and ports. This hash does not get
installed into and override the normal skb hash, so this change has
no effect whatsoever on the rest of the stack.
Reported-by: Eric Leblond <eric@regit.org>
Tested-by: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since bpf_prog_get() and program type check is used in a couple of places,
refactor this into a small helper function that we can make use of. Since
the non RO prog->aux part is not used in performance critical paths and a
program destruction via RCU is rather very unlikley when doing the put, we
shouldn't have an issue just doing the bpf_prog_get() + prog->type != type
check, but actually not taking the ref at all (due to being in fdget() /
fdput() section of the bpf fd) is even cleaner and makes the diff smaller
as well, so just go for that. Callsites are changed to make use of the new
helper where possible.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This option was removed in commit 47dcf0cb10 ("[NET]: Rethink mark field
in struct flowi").
Signed-off-by: Moritz Sichert <moritz+linux@sichert.me>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There are code duplications of a masked ethernet address comparison here
so make it a separate function instead.
Miscellanea:
o Neaten alignment of FWINV macro uses to make it clearer for the reader
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need for a special case to handle NF_INET_POST_ROUTING, this is
basically the same handling as for prerouting, input, forward.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch introduces a new event - NETDEV_CHANGE_TX_QUEUE_LEN, this
will be triggered when tx_queue_len. It could be used by net device
who want to do some processing at that time. An example is tun who may
want to resize tx array when tx_queue_len is changed.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cl->cl_vt alone is relative only to the current backlog period, while
the curve operates on cumulative virtual time. This patch adds missing
cl->cl_vtoff.
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a class is going passive, it should update its cl_vt first
to be consistent with the last dequeue operation.
Otherwise its cl_vt will be one packet behind and parent's cvtmax might
not be updated as well.
One possible side effect is if some class goes passive and subsequently
goes active /without/ its parent going passive - with cl_vt lagging one
packet behind - comparison made in init_vf() will be affected (same
period).
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is update to:
commit a09ceb0e08 ("sched: remove qdisc->drop")
That commit removed qdisc->drop, but left alone dlist and droplist
that no longer serve any meaningful purpose.
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
The condition can only succeed on wrong configurations.
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtime scheduling implemented in HFSC uses head of the queue to make
the decision about which packet to schedule next. But in case of any
head drop, the deadline calculated for the previous head is not
necessarily correct for the next head (unless both packets have the same
length).
Thanks to peek() function used during dequeue - which internally is a
dequeue operation - hfsc is almost safe from this issue, as peek()
dequeues and isolates the head storing it temporarily until the real
dequeue happens.
But there is one exception: if after the class activation a drop happens
before the first dequeue operation, there's never a chance to do the
peek().
Adding peek() call in enqueue - if this is the first packet in a new
backlog period AND the scheduler has realtime curve defined - fixes that
one corner case. The 1st hfsc_dequeue() will use that peeked packet,
similarly as every subsequent hfsc_dequeue() call uses packet peeked by
the previous call.
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some arches have virtually mapped kernel stacks, or will soon have.
tcp_md5_hash_header() uses an automatic variable to copy tcp header
before mangling th->check and calling crypto function, which might
be problematic on such arches.
David says that using percpu storage is also problematic on non SMP
builds.
Just use kmalloc() to allocate scratch areas.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a jumbo packet is being split up and processed, the crypto checksum
for each split-out packet is in the jumbo header and needs placing in the
reconstructed packet header.
When the code was changed to keep the stored copy of the packet header in
host byte order, this reconstruction was missed.
Found with sparse with CF=-D__CHECK_ENDIAN__:
../net/rxrpc/input.c:479:33: warning: incorrect type in assignment (different base types)
../net/rxrpc/input.c:479:33: expected unsigned short [unsigned] [usertype] _rsvd
../net/rxrpc/input.c:479:33: got restricted __be16 [addressable] [usertype] _rsvd
Fixes: 0d12f8a402 ("rxrpc: Keep the skb private record of the Rx header in host byte order")
Signed-off-by: David Howells <dhowells@redhat.com>
ip_skb_dst_mtu uses skb->sk, assuming it is an AF_INET socket (e.g. it
calls ip_sk_use_pmtu which casts sk as an inet_sk).
However, in the case of UDP tunneling, the skb->sk is not necessarily an
inet socket (could be AF_PACKET socket, or AF_UNSPEC if arriving from
tun/tap).
OTOH, the sk passed as an argument throughout IP stack's output path is
the one which is of PMTU interest:
- In case of local sockets, sk is same as skb->sk;
- In case of a udp tunnel, sk is the tunneling socket.
Fix, by passing ip_finish_output's sk to ip_skb_dst_mtu.
This augments 7026b1ddb6 'netfilter: Pass socket pointer down through okfn().'
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding rule with NLM_F_EXCL flag then check if the same rule exist.
If yes then exit with -EEXIST.
This is already implemented in iproute2:
if (cmd == RTM_NEWRULE) {
req.n.nlmsg_flags |= NLM_F_CREATE|NLM_F_EXCL;
req.r.rtm_type = RTN_UNICAST;
}
Tested ipv4 and ipv6 with net-next linux on qemu x86
expected behavior after patch:
localhost ~ # ip rule
0: from all lookup local
32766: from all lookup main
32767: from all lookup default
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
RTNETLINK answers: File exists
localhost ~ # ip rule
0: from all lookup local
1005: from 10.46.177.97 lookup 104
32766: from all lookup main
32767: from all lookup default
There was already topic regarding this but I don't see any changes
merged and problem still occurs.
https://lkml.kernel.org/r/1135778809.5944.7.camel+%28%29+localhost+%21+localdomain
Signed-off-by: Mateusz Bajorski <mateusz.bajorski@nokia.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found that sometimes a restored tcp socket doesn't work.
A reason of this bug is incorrect window parameters and in this case
tcp_acceptable_seq() returns tcp_wnd_end(tp) instead of tp->snd_nxt. The
other side drops packets with this seq, because seq is less than
tp->rcv_nxt ( tcp_sequence() ).
Data from a send queue is sent only if there is enough space in a
window, so when we restore unacked data, we need to expand a window to
fit this data.
This was in a first version of this patch:
"tcp: extend window to fit all restored unacked data in a send queue"
Then Alexey recommended me to restore window parameters instead of
adjusted them according with data in a sent queue. This sounds resonable.
rcv_wnd has to be restored, because it was reported to another side
and the offered window is never shrunk.
One of reasons why we need to restore snd_wnd was described above.
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds stats support for the currently used IGMP/MLD types by the
bridge. The stats are per-port (plus one stat per-bridge) and per-direction
(RX/TX). The stats are exported via netlink via the new linkxstats API
(RTM_GETSTATS). In order to minimize the performance impact, a new option
is used to enable/disable the stats - multicast_stats_enabled, similar to
the recent vlan stats. Also in order to avoid multiple IGMP/MLD type
lookups and checks, we make use of the current "igmp" member of the bridge
private skb->cb region to record the type on Rx (both host-generated and
external packets pass by multicast_rcv()). We can do that since the igmp
member was used as a boolean and all the valid IGMP/MLD types are positive
values. The normal bridge fast-path is not affected at all, the only
affected paths are the flooding ones and since we make use of the IGMP/MLD
type, we can quickly determine if the packet should be counted using
cache-hot data (cb's igmp member). We add counters for:
* IGMP Queries
* IGMP Leaves
* IGMP v1/v2/v3 reports
* MLD Queries
* MLD Leaves
* MLD v1/v2 reports
These are invaluable when monitoring or debugging complex multicast setups
with bridges.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the IFLA_STATS_LINK_XSTATS_SLAVE attribute
which allows to export per-slave statistics if the master device supports
the linkxstats callback. The attribute is passed down to the linkxstats
callback and it is up to the callback user to use it (an example has been
added to the only current user - the bridge). This allows us to query only
specific slaves of master devices like bridge ports and export only what
we're interested in instead of having to dump all ports and searching only
for a single one. This will be used to export per-port IGMP/MLD stats and
also per-port vlan stats in the future, possibly other statistics as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've accumulated a couple of different fixes now to mesh_sta_cleanup()
due to the different paths that user_mpm and !user_mpm cases take -- one
fix to flush nexthop paths and one to fix the counting.
The only caller of mesh_plink_deactivate() is mesh_sta_cleanup(), so we
can push the user_mpm checks down into there in order to share more
code.
In doing so, we can remove an extra call to mesh_path_flush_by_nexthop()
and the (unnecessary) call to mesh_accept_plinks_update(). This will
also ensure the powersaving state code gets called in the user_mpm case.
The only cleanup tasks we need to avoid when MPM is in user-space
are sending the peering frames and stopping the plink timer, so wrap
those in the appropriate check.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Previously, the action frames to group address was not encrypted. But
[1] "Table 8-38 Category values" indicates "Mesh" and "Multihop" category
action frames should be encrypted (Group addressed privacy == yes). And the
encyption key should be MGTK ([1] 10.13 Group addressed robust management frame
procedures). So this patch modifies the code to make it suitable for spec.
[1] IEEE Std 802.11-2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
We normally return an uninitialized value, but no one checks it so it
doesn't matter. Anyway, let's silence the static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
When building a kernel with W=1, the nl80211.c file causes a number of
warnings, all about the same problem:
net/wireless/nl80211.c: In function 'nl80211_parse_mesh_config':
net/wireless/nl80211.c:5287:103: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5290:96: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5293:124: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5295:148: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5298:106: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5305:116: error: comparison is always false due to limited range of data type [-Werror=type-limits]
The problem is that gcc does not notice that the check is generate
by a macro, so it complains about comparing an unsigned type against 0.
I've tried to come up with a way to rephrase that code in a way that
avoids the warnings and otherwise improves the code as well.
This uses a set of new helper functions that perform the range checking,
and should provide slightly better type safety than the older patch,
at the expense of adding 44 lines to the code. Binary code size is
basically unchanged though (20 bytes added to 126561 bytes .text).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
This work adds a helper for changing skb->pkt_type in a controlled way.
We only allow a subset of possible values and can extend that in future
should other use cases come up. Doing this as a helper has the advantage
that errors can be handeled gracefully and thus helper kept extensible.
It's a write counterpart to pkt_type member we can already read from
struct __sk_buff context. Major use case is to change incoming skbs to
PACKET_HOST in a programmatic way instead of having to recirculate via
redirect(..., BPF_F_INGRESS), for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a minimal helper for doing the groundwork of changing
the skb->protocol in a controlled way. Currently supported is v4 to
v6 and vice versa transitions, which allows f.e. for a minimal, static
nat64 implementation where applications in containers that still
require IPv4 can be transparently operated in an IPv6-only environment.
For example, host facing veth of the container can transparently do
the transitions in a programmatic way with the help of clsact qdisc
and cls_bpf.
Idea is to separate concerns for keeping complexity of the helper
lower, which means that the programs utilize bpf_skb_change_proto(),
bpf_skb_store_bytes() and bpf_lX_csum_replace() to get the job done,
instead of doing everything in a single helper (and thus partially
duplicating helper functionality). Also, bpf_skb_change_proto()
shouldn't need to deal with raw packet data as this is done by other
helpers.
bpf_skb_proto_6_to_4() and bpf_skb_proto_4_to_6() unclone the skb to
operate on a private one, push or pop additionally required header
space and migrate the gso/gro meta data from the shared info. We do
mark the gso type as dodgy so that headers are checked and segs
recalculated by the gso/gro engine. The gso_size target is adapted
as well. The flags argument added is currently reserved and can be
used for future extensions.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use smp_processor_id() for the generic helper bpf_get_smp_processor_id()
instead of the raw variant. This allows for preemption checks when we
have DEBUG_PREEMPT, and otherwise uses the raw variant anyway. We only
need to keep the raw variant for socket filters, but we can reuse the
helper that is already there from cBPF side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
The bat_algo.h had some functions declared which were not part of the
bat_algo.c file. These are instead stored in bat_v.c and bat_iv_ogm.c. The
declaration should therefore be also in bat_v.h and bat_iv_ogm,h to make
them easier to find.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This patch adds a debugfs table with originators and their according
multicast flags to help users figure out why multicast optimizations
might be enabled or disabled for them.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
There are several places in batman-adv which provide logging related
functions. These should be grouped together in the log.* files to make them
easier to find.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch changes relevant to a node's own multicast flags are
printed to the 'mcast' log level.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The bat_algo functionality in main.c is mostly unrelated to the rest of the
content. It still takes up a large portion of this source file (~15%, 103
lines). Moving it to a separate file makes it better visible as a main
component of the batman-adv implementation and hides it less in the other
helper functions in main.c.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch we are finally able to support multicast optimizations
in bridged setups, too. So far, if a bridge was added on top of a
soft-interface (e.g. bat0) the batman-adv multicast optimizations
needed to be disabled to avoid packetloss.
Current Linux bridge implementations and API can now provide us
with the so far missing information about interested but "remote"
multicast receivers behind bridge ports.
The Linux bridge performs the detection of remote participants
interested in multicast packets with its own and mature so
called IGMP and MLD snooping code and stores that in its
database. With the new API provided by the bridge batman-adv can
now simply hook into this database.
We then reliably announce the gathered multicast listeners to
other nodes through the batman-adv translation table.
Additionally, the Linux bridge provides us with the information about
whether an IGMP/MLD querier exists. If there is none then we need to
disable multicast optimizations as we cannot learn about multicast
listeners on external, bridged-in host then.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The tvlv functionality in main.c is mostly unrelated to the rest of the
content. It still takes up a large portion of this source file (~45%, 588
lines). Moving it to a separate file makes it better visible as a main
component of the batman-adv implementation and hides it less in the other
helper functions in main.c
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[sven@narfation.org: fix conflicts with current version, fix includes,
rewrote commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch IGMP or MLD reports are always flooded. This is
necessary for the upcoming bridge integration to function without
multicast packet loss.
With the report handling so far bridges might miss interested multicast
listeners, leading to wrongly excluding ports from multicast packet
forwarding.
Currently we are treating IGMP/MLD reports, the messages bridges use to
learn about interested multicast listeners, just as any other multicast
packet: We try to send them to nodes matching its multicast destination.
Unfortunately, the destination address of reports of the older
IGMPv2/MLDv1 protocol families do not strictly adhere to their own
protocol: More precisely, the interested receiver, an IGMPv2 or MLDv1
querier, itself usually does not listen to the multicast destination
address of any reports.
Therefore with this patch we are simply excluding IGMP/MLD reports from
the multicast forwarding code path and keep flooding them. By that
any bridge receives them and can properly learn about listeners.
To avoid compatibility issues with older nodes not yet implementing this
report handling, we need to force them to flood reports: We do this by
bumping the multicast TVLV version to 2, effectively disabling their
multicast optimization.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is easier to detect if a include is already there for a used
functionality when the includes are ordered. Using an alphabetic order
together with the grouping in commit 1e2c2a4fe4 ("batman-adv: Add
required includes to all files") makes includes better manageable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Unfragmented frames which traverse a node have their skb->priority set
by looking at the IP ToS byte, or the 802.1p header. However for
fragments this is not possible, only one of the fragments will contain
the headers. Instead, place the priority into the fragment header and
on receiving a fragment, use this information to set the skb->priority
for when the fragment is forwarded.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
main.h includes statements which (re)define preprocessor variables which
influence the compiled code. This makes it necessary to include it in all
files. For example, it redefines pr_fmt used to the module as prefix for
each pr_* message.
Reported-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
BATMAN will set the skb->priority based on the IP precedence or 802.1q
tag. However, if it needs to fragment the frame, it currently leaves
the fragment skb with the default priority and actually overwrites the
priority in the unfragmented frame. Fix this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The ELP interval and throughput override interface settings are initialized
with default settings on every time an interface is added to a mesh.
This patch prevents this behavior by moving the configuration init to the
interface detection routine which runs only once per interface.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[a@unstable.cc: move initialization to batadv_v_hardif_init]
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
To reduce the field pollution in our main batadv_priv data structure
we've already created some substructures so that we could group fields
in a convenient manner.
However gw_mode and gw_sel_class are still part of the main object.
More both fields to the GW private substructure.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
the compiler can optimize functions within the same C file and therefore
there is no need to make it explicit.
Remove the useless inline attribute for __batadv_store_uint_attr()
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The ogm_emit and ogm_schedule API calls were rather tight to the
B.A.T.M.A.N. IV logic and therefore rather difficult to use
with other algorithm implementations.
Remove such calls and move the surrounding logic into the
B.A.T.M.A.N. IV specific code.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
To make it easier to search through the code it is better to print static
strings directly instead of using format strings printing constants.
This was addressed in a previous patch, but the Gateway table header
was not updated accordingly.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Pull networking fixes from David Miller:
"I've been traveling so this accumulates more than week or so of bug
fixing. It perhaps looks a little worse than it really is.
1) Fix deadlock in ath10k driver, from Ben Greear.
2) Increase scan timeout in iwlwifi, from Luca Coelho.
3) Unbreak STP by properly reinjecting STP packets back into the
stack. Regression fix from Ido Schimmel.
4) Mediatek driver fixes (missing malloc failure checks, leaking of
scratch memory, wrong indexing when mapping TX buffers, etc.) from
John Crispin.
5) Fix endianness bug in icmpv6_err() handler, from Hannes Frederic
Sowa.
6) Fix hashing of flows in UDP in the ruseport case, from Xuemin Su.
7) Fix netlink notifications in ovs for tunnels, delete link messages
are never emitted because of how the device registry state is
handled. From Nicolas Dichtel.
8) Conntrack module leaks kmemcache on unload, from Florian Westphal.
9) Prevent endless jump loops in nft rules, from Liping Zhang and
Pablo Neira Ayuso.
10) Not early enough spinlock initialization in mlx4, from Eric
Dumazet.
11) Bind refcount leak in act_ipt, from Cong WANG.
12) Missing RCU locking in HTB scheduler, from Florian Westphal.
13) Several small MACSEC bug fixes from Sabrina Dubroca (missing RCU
barrier, using heap for SG and IV, and erroneous use of async flag
when allocating AEAD conext.)
14) RCU handling fix in TIPC, from Ying Xue.
15) Pass correct protocol down into ipv4_{update_pmtu,redirect}() in
SIT driver, from Simon Horman.
16) Socket timer deadlock fix in TIPC from Jon Paul Maloy.
17) Fix potential deadlock in team enslave, from Ido Schimmel.
18) Memory leak in KCM procfs handling, from Jiri Slaby.
19) ESN generation fix in ipv4 ESP, from Herbert Xu.
20) Fix GFP_KERNEL allocations with locks held in act_ife, from Cong
WANG.
21) Use after free in netem, from Eric Dumazet.
22) Uninitialized last assert time in multicast router code, from Tom
Goff.
23) Skip raw sockets in sock_diag destruction broadcast, from Willem
de Bruijn.
24) Fix link status reporting in thunderx, from Sunil Goutham.
25) Limit resegmentation of retransmit queue so that we do not
retransmit too large GSO frames. From Eric Dumazet.
26) Delay bpf program release after grace period, from Daniel
Borkmann"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (141 commits)
openvswitch: fix conntrack netlink event delivery
qed: Protect the doorbell BAR with the write barriers.
neigh: Explicitly declare RCU-bh read side critical section in neigh_xmit()
e1000e: keep VLAN interfaces functional after rxvlan off
cfg80211: fix proto in ieee80211_data_to_8023 for frames without LLC header
qlcnic: use the correct ring in qlcnic_83xx_process_rcv_ring_diag()
bpf, perf: delay release of BPF prog after grace period
net: bridge: fix vlan stats continue counter
tcp: do not send too big packets at retransmit time
ibmvnic: fix to use list_for_each_safe() when delete items
net: thunderx: Fix TL4 configuration for secondary Qsets
net: thunderx: Fix link status reporting
net/mlx5e: Reorganize ethtool statistics
net/mlx5e: Fix number of PFC counters reported to ethtool
net/mlx5e: Prevent adding the same vxlan port
net/mlx5e: Check for BlueFlame capability before allocating SQ uar
net/mlx5e: Change enum to better reflect usage
net/mlx5: Add ConnectX-5 PCIe 4.0 to list of supported devices
net/mlx5: Update command strings
net: marvell: Add separate config ANEG function for Marvell 88E1111
...
* fix mesh peer link counter, decrement wasn't always done at all
* fix ethertype (length) for packets without RFC 1042 or bridge
tunnel header
-----BEGIN PGP SIGNATURE-----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=dAbs
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-06-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two small fixes
* fix mesh peer link counter, decrement wasn't always done at all
* fix ethertype (length) for packets without RFC 1042 or bridge
tunnel header
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first and last netlink message for a particular conntrack are
actually sent. The first message is sent through nf_conntrack_confirm when
the conntrack is committed. The last one is sent when the conntrack is
destroyed on timeout. The other conntrack state change messages are not
advertised.
When the conntrack subsystem is used from netfilter, nf_conntrack_confirm
is called for each packet, from the postrouting hook, which in turn calls
nf_ct_deliver_cached_events to send the state change netlink messages.
This commit fixes the problem by calling nf_ct_deliver_cached_events in the
non-commit case as well.
Fixes: 7f8a436eaa ("openvswitch: Add conntrack action")
CC: Joe Stringer <joestringer@nicira.com>
CC: Justin Pettit <jpettit@nicira.com>
CC: Andy Zhou <azhou@nicira.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Samuel Gauthier <samuel.gauthier@6wind.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_unshare() fails, we call qdisc_drop() with a NULL skb, which
is no longer supported.
Fixes: 520ac30f45 ("net_sched: drop packets after root qdisc lock is released")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_xmit() expects to be called inside an RCU-bh read side critical
section, and while one of its two current callers gets this right, the
other one doesn't.
More specifically, neigh_xmit() has two callers, mpls_forward() and
mpls_output(), and while both callers call neigh_xmit() under
rcu_read_lock(), this provides sufficient protection for neigh_xmit()
only in the case of mpls_forward(), as that is always called from
softirq context and therefore doesn't need explicit BH protection,
while mpls_output() can be called from process context with softirqs
enabled.
When mpls_output() is called from process context, with softirqs
enabled, we can be preempted by a softirq at any time, and RCU-bh
considers the completion of a softirq as signaling the end of any
pending read-side critical sections, so if we do get a softirq
while we are in the part of neigh_xmit() that expects to be run inside
an RCU-bh read side critical section, we can end up with an unexpected
RCU grace period running right in the middle of that critical section,
making things go boom.
This patch fixes this impedance mismatch in the callee, by making
neigh_xmit() always take rcu_read_{,un}lock_bh() around the code that
expects to be treated as an RCU-bh read side critical section, as this
seems a safer option than fixing it in the callers.
Fixes: 4fd3d7d9e8 ("neigh: Add helper function neigh_xmit")
Signed-off-by: David Barroso <dbarroso@fastly.com>
Signed-off-by: Lennert Buytenhek <lbuytenhek@fastly.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.
The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.
Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.
Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.
Fixes: 2d1c304cb2 ("cfg80211: add function for 802.3 conversion with separate output buffer")
Cc: stable@vger.kernel.org
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
I made a dumb off-by-one mistake when I added the vlan stats counter
dumping code. The increment should happen before the check, not after
otherwise we miss one entry when we continue dumping.
Fixes: a60c090361 ("bridge: netlink: export per-vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun reported a bug in TCP stack and bisected it to a recent commit.
In case where we process SACK, we can coalesce multiple skbs
into fat ones (tcp_shift_skb_data()), to lower write queue
overhead, because we do not expect to retransmit these packets.
However, SACK reneging can happen, forcing the sender to retransmit
all these packets. If skb->len is above 64KB, we then send buggy
IP packets that could hang TSO engine on cxgb4.
Neal suggested to use tcp_tso_autosize() instead of tp->gso_segs
so that we cook packets of optimal size vs TCP/pacing.
Thanks to Arjun for reporting the bug and running the tests !
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Arjun V <arjun@chelsio.com>
Tested-by: Arjun V <arjun@chelsio.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Context implies that port in struct "udp_media_addr" is referring
to a UDP port.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP msg2addr function tipc_udp_msg2addr() can return -EINVAL which
prior to this patch was unhanded in the caller.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The space is missing before the open parenthesis '(', and this
will introduce much more noise when checking patch around.
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The untagged vlan object is only destroyed when the interface is removed
via the legacy sysfs interface. But it also has to be destroyed when the
standard rtnl-link interface is used.
Fixes: 5d2c05b213 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_linearize may reallocate the skb. This makes the calculated pointer
for ethhdr invalid. But it the pointer is used later to fill in the RR
field of the batadv_icmp_packet_rr packet.
Instead re-evaluate eth_hdr after the skb_linearize+skb_cow to fix the
pointer and avoid the invalid read.
Fixes: da6b8c20a5 ("batman-adv: generalize batman-adv icmp packet handling")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each batadv_tt_local_entry hold a single reference to a
batadv_softif_vlan. In case a new entry cannot be added to the hash
table, the error path puts the reference, but the reference will also
now be dropped by batadv_tt_local_entry_release().
Fixes: a33d970d0b ("batman-adv: Fix reference counting of vlan object for tt_local_entry")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tt_req_node is added and removed from a list inside a spinlock. But the
locking is sometimes removed even when the object is still referenced and
will be used later via this reference. For example batadv_send_tt_request
can create a new tt_req_node (including add to a list) and later
re-acquires the lock to remove it from the list and to free it. But at this
time another context could have already removed this tt_req_node from the
list and freed it.
CPU#0
batadv_batman_skb_recv from net_device 0
-> batadv_iv_ogm_receive
-> batadv_iv_ogm_process
-> batadv_iv_ogm_process_per_outif
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_ogm_handler_v1
-> batadv_tt_update_orig
-> batadv_send_tt_request
-> batadv_tt_req_node_new
spin_lock(...)
allocates new tt_req_node and adds it to list
spin_unlock(...)
return tt_req_node
CPU#1
batadv_batman_skb_recv from net_device 1
-> batadv_recv_unicast_tvlv
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_unicast_handler_v1
-> batadv_handle_tt_response
spin_lock(...)
tt_req_node gets removed from list and is freed
spin_unlock(...)
CPU#0
<- returned to batadv_send_tt_request
spin_lock(...)
tt_req_node gets removed from list and is freed
MEMORY CORRUPTION/SEGFAULT/...
spin_unlock(...)
This can only be solved via reference counting to allow multiple contexts
to handle the list manipulation while making sure that only the last
context holding a reference will free the object.
Fixes: a73105b8d4 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Tested-by: Amadeus Alfa <amadeus@chemnitz.freifunk.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a VLAN tagged frame is received and the corresponding VLAN is not
configured on the soft interface, it will splat a WARN on every packet
received. This is a quite annoying behaviour for some scenarios, e.g. if
bat0 is bridged with eth0, and there are arbitrary VLAN tagged frames
from Ethernet coming in without having any VLAN configuration on bat0.
The code should probably create vlan objects on the fly and
transparently transport these VLAN-tagged Ethernet frames, but until
this is done, at least the WARN splat should be replaced by a rate
limited output.
Fixes: 354136bcc3 ("batman-adv: fix kernel crash due to missing NULL checks")
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge is falsly dropping ipv6 mulitcast packets if there is:
1. No ipv6 address assigned on the brigde.
2. No external mld querier present.
3. The internal querier enabled.
When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.
Ipv6 multicast snooping can only work if:
a) An external querier is present
OR
b) The bridge has an ipv6 address an is capable of sending own queries
Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.
This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().
Special thanks to Linus Lüssing.
Fixes: d1d81d4c3d ("bridge: check return value of ipv6_dev_get_saddr()")
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user space program (e.g., wpa_supplicant) deletes a STA entry that
is currently in NL80211_PLINK_ESTAB state, the number of established
plinks counter was not decremented and this could result in rejecting
new plink establishment before really hitting the real maximum plink
limit. For !user_mpm case, this decrementation is handled by
mesh_plink_deactive().
Fix this by decrementing estab_plinks on STA deletion
(mesh_sta_cleanup() gets called from there) so that the counter has a
correct value and the Beacon frame advertisement in Mesh Configuration
element shows the proper value for capability to accept additional
peers.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Drop redundant include of moduleparam.h
The Coccinelle semantic patch used to make this change is as follows:
@ includesmodule @
@@
#include <linux/module.h>
@ depends on includesmodule @
@@
- #include <linux/moduleparam.h>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
