We were mapping an extra byte (and hence usually an extra page):
iommu_prepare_identity_map() expects to be given an 'end' argument which
is the last byte to be mapped; not the first byte *not* to be mapped.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The comment in domain_remove_one_dev_info() states "No need to compare
PCI domain; it has to be the same". But for the si_domain that isn't
going to be true, as it consists of all the PCI devices that are
identity mapped thus multiple PCI domains can be in si_domain. The
code needs to validate the PCI domain too.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When using the 1:1 (identity) PCI DMA remapping, PCI Host Bridge devices
that do not use the IOMMU causes a kernel panic. Fix that by not
inserting those devices into the si_domain.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The __intel_map_single function is not honoring the passed in DMA mask.
This results in not using the coherent DMA mask when called from
intel_alloc_coherent().
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Travis and Mike Habeck reported an issue where iova allocation
would return a range that was larger than a device's dma mask.
https://lkml.org/lkml/2011/3/29/423
The dmar initialization code will reserve all PCI MMIO regions and copy
those reservations into a domain specific iova tree. It is possible for
one of those regions to be above the dma mask of a device. It is typical
to allocate iovas with a 32bit mask (despite device's dma mask possibly
being larger) and cache the result until it exhausts the lower 32bit
address space. Freeing the iova range that is >= the last iova in the
lower 32bit range when there is still an iova above the 32bit range will
corrupt the cached iova by pointing it to a region that is above 32bit.
If that region is also larger than the device's dma mask, a subsequent
allocation will return an unusable iova and cause dma failure.
Simply don't cache an iova that is above the 32bit caching boundary.
Reported-by: Mike Travis <travis@sgi.com>
Reported-by: Mike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Acked-by: Mike Travis <travis@sgi.com>
Tested-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When there are a large count of PCI devices, and the pass through
option for iommu is set, much time is spent in the identity_mapping
function hunting though the iommu domains to check if a specific
device is "identity mapped".
Speed up the function by checking the cached info to see if
it's mapped to the static identity domain.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The identity mapping code appears to make the assumption that if the
devices dma_mask is greater than 32bits the device can use identity
mapping. But that is not true: take the case where we have a 40bit
device in a 44bit architecture. The device can potentially receive a
physical address that it will truncate and cause incorrect addresses
to be used.
Instead check to see if the device's dma_mask is large enough
to address the system's dma_mask.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit a97590e5 added unlinking domains from iommus to reciprocate the
iommu from domains unlinking that was already done. We actually want
to only do this for device domains and never for the static
identity map domain or VM domains. The SI domain is special and
never freed, while VM domain->id lives in their own special address
space, separate from iommu->domain_ids.
In the current code, a VM can get domain->id zero, then mark that
domain unused when unbound from pci-stub. This leads to DMAR
write faults when the device is re-bound to the host driver.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are no externally-visible changes with this. In the loop in the
internal __domain_mapping() function, we simply detect if we are mapping:
- size >= 2MiB, and
- virtual address aligned to 2MiB, and
- physical address aligned to 2MiB, and
- on hardware that supports superpages.
(and likewise for larger superpages).
We automatically use a superpage for such mappings. We never have to
worry about *breaking* superpages, since we trust that we will always
*unmap* the same range that was mapped. So all we need to do is ensure
that dma_pte_clear_range() will also cope with superpages.
Adjust pfn_to_dma_pte() to take a superpage 'level' as an argument, so
it can return a PTE at the appropriate level rather than always
extending the page tables all the way down to level 1. Again, this is
simplified by the fact that we should never encounter existing small
pages when we're creating a mapping; any old mapping that used the same
virtual range will have been entirely removed and its obsolete page
tables freed.
Provide an 'intel_iommu=sp_off' argument on the command line as a
chicken bit. Not that it should ever be required.
==
The original commit seen in the iommu-2.6.git was Youquan's
implementation (and completion) of my own half-baked code which I'd
typed into an email. Followed by half a dozen subsequent 'fixes'.
I've taken the unusual step of rewriting history and collapsing the
original commits in order to keep the main history simpler, and make
life easier for the people who are going to have to backport this to
older kernels. And also so I can give it a more coherent commit comment
which (hopefully) gives a better explanation of what's going on.
The original sequence of commits leading to identical code was:
Youquan Song (3):
intel-iommu: super page support
intel-iommu: Fix superpage alignment calculation error
intel-iommu: Fix superpage level calculation error in dma_pfn_level_pte()
David Woodhouse (4):
intel-iommu: Precalculate superpage support for dmar_domain
intel-iommu: Fix hardware_largepage_caps()
intel-iommu: Fix inappropriate use of superpages in __domain_mapping()
intel-iommu: Fix phys_pfn in __domain_mapping for sglist pages
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.
Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new instruction_pointer_set helper is defined for people who have
converted to asm-generic/ptrace.h, so don't use it generally unless
the arch needs it (in which case it has been converted). This should
fix building of kgdb tests for arches not yet converted.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit e5cb966c08.
It causes new build regressions with gcc-4.2 which is
pretty common on non-x86 platforms.
Reported-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
catc_ctrl_run() calls usb_submit_urb() with GFP_KERNEL, while it is called from
catc_ctrl_async() and catc_ctrl_done() with catc->ctrl_lock spinlock held.
The patch replaces GFP_KERNEL with GFP_ATOMIC.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a driver crash during packet reception due to not enough
bytes allocated in the skb. Since the loop reads out 4 bytes at a time, we
need to allow for up to 3 bytes of slack space.
Signed-off-by: Dennis Aberilla <denzzzhome@yahoo.com>
Signed-off-by: David S. Miller <davem@zippy.davemloft.net>
For 6150 devices, modify the supported PCI subsystem ID.
Cc: stable@kernel.org
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211 devices register 'EP 4 OUT' endpoint as Interrupt type on USB 2.0:
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
However on USB 1.1 endpoint becomes Bulk:
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Commit 37939810b9 assumed that endpoint is
always interrupt type and changed usb_bulk_msg() calls to usb_interrupt_msg().
Problem here is that usb_bulk_msg() on interrupt endpoint selfcorrects the
call and changes requested pipe to interrupt type (see usb_bulk_msg).
However with usb_interrupt_msg() on bulk endpoint does not correct the
pipe type to bulk, but instead URB is submitted with interrupt type pipe.
So pre-2.6.39 used usb_bulk_msg() and therefore worked with both endpoint
types, however in 2.6.39 usb_interrupt_msg() with bulk endpoint causes
ohci_hcd to fail submitted URB instantly with -ENOSPC and preventing zd1211rw
from working with OHCI.
Fix this by detecting endpoint type and using correct endpoint/pipe types
for URB. Also fix asynchronous zd_usb_iowrite16v_async() to use right
URB type on 'EP 4 OUT'.
Cc: stable@kernel.org
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix kernel oops when trying to use passive scheduled scans. The
reason was that in passive scans there are no SSIDs, so there was a
NULL pointer dereference.
To solve the problem, we now check the number of SSIDs provided in the
sched_scan request and only access the list if there's one or more
(ie. passive scan is not forced). We also force all the channels to
be passive by adding the IEEE80211_CHAN_PASSIVE_SCAN flag locally
before the checks in the wl1271_scan_get_sched_scan_channels()
function.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a different value for DFS dwell time when performing a scheduled
scan. Previously we were using the same value as for normal passive
scans. This adds some flexibility between these two different types
of passive scan.
For now we use 150 TUs for DFS channel dwell time. This may need to
be fine-tuned in the future.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DFS channels were never getting included in the scheduled scans,
because they always contain the passive flag as well and the call was
asking for DFS and active channels.
Fix this by ignoring the passive flag when collecting DFS channels.
Also, move the DFS channels in the channel list before the 5GHz active
channels (this was implemented in the FW differently than specified).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were comparing bitwise AND results with a boolean, so when the
boolean was set to true, it was not matching as it should.
Fix this by booleanizing the bitwise AND results with !!.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before this patch, the command sequence number is being set before
lbs_queue_cmd() adds the command to the queue. However, lbs_queue_cmd()
sometimes forces commands to queue-jump (e.g. CMD_802_11_WAKEUP_CONFIRM).
It currently does this without considering that sequence numbers might need
adjusting to keep things running in order.
Fix this by setting the sequence number at a later stage, just before
we're actually submitting the command to the hardware. Also fixes a
possible race where seqnum was being modified outside of the driver
lock.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 1b842e91fe.
There is a fundamental ordering race between the early and late probe
paths and the runtime PM tie-in that results in __pm_runtime_resume()
attempting to take a lock that hasn't been initialized yet (which by
proxy also suggests that pm_runtime_init() hasn't yet been run on the
device either, making the entire thing unsafe) -- resulting in instant
death on SMP or on UP with spinlock debugging enabled:
sh_tmu.0: used for clock events
sh_tmu.0: used for periodic clock events
BUG: spinlock trylock failure on UP on CPU#0, swapper/0
lock: 804db198, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
...
Revert it for now until the ordering issues can be resolved, or we can get
some more help from the runtime PM framework to make this possible.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ask for delayed callbacks on TX ring full, to give the
other side more of a chance to make progress.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add an API that tells the other side that callbacks
should be delayed until a lot of work has been done.
Implement using the new event_idx feature.
Note: it might seem advantageous to let the drivers
ask for a callback after a specific capacity has
been reached. However, as a single head can
free many entries in the descriptor table,
we don't really have a clue about capacity
until get_buf is called. The API is the simplest
to implement at the moment, we'll see what kind of
hints drivers can pass when there's more than one
user of the feature.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Support the new event index feature. When acked,
utilize it to reduce the # of interrupts sent to the guest.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Support for the new event idx feature:
1. When enabling interrupts, publish the current avail index
value to the host to get interrupts on the next update.
2. Use the new avail_event feature to reduce the number
of exits from the guest.
Simple test with the simulator:
[virtio]# time ./virtio_test
spurious wakeus: 0x7
real 0m0.169s
user 0m0.140s
sys 0m0.019s
[virtio]# time ./virtio_test --no-event-idx
spurious wakeus: 0x11
real 0m0.649s
user 0m0.295s
sys 0m0.335s
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The virtio balloon driver has a VIRTIO_BALLOON_F_MUST_TELL_HOST
feature bit. Whenever the bit is set, the guest kernel must
always tell the host before we free pages back to the allocator.
Without this feature, we might free a page (and have another
user touch it) while the hypervisor is unprepared for it.
But, if the bit is _not_ set, we are under no obligation to
reverse the order; we're under no obligation to do _anything_.
As of now, qemu-kvm defines the bit, but doesn't set it.
This patch makes the "tell host first" logic the only case. This
should make everybody happy, and reduce the amount of untested or
untestable code in the kernel.
This _also_ means that we don't have to preserve a pfn list
after the pages are freed, which should let us get rid of some
temporary storage (vb->pfns) eventually.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
That's already been done by the virtio infrastructure before the probe
function is called.
Reported-by: alexey.kardashevskiy@au1.ibm.com
Acked-by: Amit Shah <amit.shah@redhat.com>
Tested-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It is easier to figure out the context by reading SCSI_SENSE_BUFFERSIZE
instead of plain '96'.
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Wire up the virtio_driver config_changed method to get notified about
config changes raised by the host. For now we just re-read the device
size to support online resizing of devices, but once we add more
attributes that might be changeable they could be added as well.
Note that the config_changed method is called from irq context, so
we'll have to use the workqueue infrastructure to provide us a proper
user context for our changes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We had a few drivers move from arch/arm into drivers/gpio, but they
don't actually compile without the ARM platform headers etc. As a
result they were messing up allyesconfig on x86.
Make them depend on ARM.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (43 commits)
acer-wmi: support integer return type from WMI methods
msi-laptop: fix section mismatch in reference from the function load_scm_model_init
acer-wmi: support to set communication device state by new wmid method
acer-wmi: allow 64-bits return buffer from WMI methods
acer-wmi: check the existence of internal 3G device when set capability
platform/x86:delete two unused variables
support wlan hotkey on Acer Travelmate 5735Z
platform-x86: intel_mid_thermal: Fix memory leak
platform/x86: Fix Makefile for intel_mid_powerbtn
platform/x86: Simplify intel_mid_powerbtn
acer-wmi: Delete out-of-date documentation
acerhdf: Clean up includes
acerhdf: Drop pointless dependency on THERMAL_HWMON
acer-wmi: Update MAINTAINERS
wmi: Orphan ACPI-WMI driver
tc1100-wmi: Orphan driver
acer-wmi: does not allow negative number set to initial device state
platform/oaktrail: ACPI EC Extra driver for Oaktrail
thinkpad_acpi: Convert printks to pr_<level>
thinkpad_acpi: Correct !CONFIG_THINKPAD_ACPI_VIDEO warning
...
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm kcopyd: return client directly and not through a pointer
dm kcopyd: reserve fewer pages
dm io: use fixed initial mempool size
dm kcopyd: alloc pages from the main page allocator
dm kcopyd: add gfp parm to alloc_pl
dm kcopyd: remove superfluous page allocation spinlock
dm kcopyd: preallocate sub jobs to avoid deadlock
dm kcopyd: avoid pointless job splitting
dm mpath: do not fail paths after integrity errors
dm table: reject devices without request fns
dm table: allow targets to support discards internally
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI EC: remove redundant code
ACPI: Add D3 cold state
ACPI: processor: fix processor_physically_present in UP kernel
ACPI: Split out custom_method functionality into an own driver
ACPI: Cleanup custom_method debug stuff
ACPI EC: enable MSI workaround for Quanta laptops
ACPICA: Update to version 20110413
ACPICA: Execute an orphan _REG method under the EC device
ACPICA: Move ACPI_NUM_PREDEFINED_REGIONS to a more appropriate place
ACPICA: Update internal address SpaceID for DataTable regions
ACPICA: Add more methods eligible for NULL package element removal
ACPICA: Split all internal Global Lock functions to new file - evglock
ACPI: EC: add another DMI check for ASUS hardware
ACPI EC: remove dead code
ACPICA: Fix code divergence of global lock handling
ACPICA: Use acpi_os_create_lock interface
ACPI: osl, add acpi_os_create_lock interface
ACPI:Fix goto flows in thermal-sys
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
x86 idle: deprecate mwait_idle() and "idle=mwait" cmdline param
x86 idle: deprecate "no-hlt" cmdline param
x86 idle APM: deprecate CONFIG_APM_CPU_IDLE
x86 idle floppy: deprecate disable_hlt()
x86 idle: EXPORT_SYMBOL(default_idle, pm_idle) only when APM demands it
x86 idle: clarify AMD erratum 400 workaround
idle governor: Avoid lock acquisition to read pm_qos before entering idle
cpuidle: menu: fixed wrapping timers at 4.294 seconds
Return client directly from dm_kcopyd_client_create, not through a
parameter, making it consistent with dm_io_client_create.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reserve just the minimum of pages needed to process one job.
Because we allocate pages from page allocator, we don't need to reserve
a large number of pages. The maximum job size is SUB_JOB_SIZE and we
calculate the number of reserved pages based on this.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Replace the arbitrary calculation of an initial io struct mempool size
with a constant.
The code calculated the number of reserved structures based on the request
size and used a "magic" multiplication constant of 4. This patch changes
it to reserve a fixed number - itself still chosen quite arbitrarily.
Further testing might show if there is a better number to choose.
Note that if there is no memory pressure, we can still allocate an
arbitrary number of "struct io" structures. One structure is enough to
process the whole request.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes dm-kcopyd so that it allocates pages from the main
page allocator with __GFP_NOWARN | __GFP_NORETRY flags (so that it can
fail in case of memory pressure). If the allocation fails, dm-kcopyd
allocates pages from its own reserve.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce a parameter for gfp flags to alloc_pl() for use in following
patches.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the spinlock protecting the pages allocation. The spinlock is only
taken on initialization or from single-threaded workqueue. Therefore, the
spinlock is useless.
The spinlock is taken in kcopyd_get_pages and kcopyd_put_pages.
kcopyd_get_pages is only called from run_pages_job, which is only
called from process_jobs called from do_work.
kcopyd_put_pages is called from client_alloc_pages (which is initialization
function) or from run_complete_job. run_complete_job is only called from
process_jobs called from do_work.
Another spinlock, kc->job_lock is taken each time someone pushes or pops
some work for the worker thread. Once we take kc->job_lock, we
guarantee that any written memory is visible to the other CPUs.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
There's a possible theoretical deadlock in dm-kcopyd because multiple
allocations from the same mempool are required to finish a request.
Avoid this by preallocating sub jobs.
There is a mempool of 512 entries. Each request requires up to 9
entries from the mempool. If we have at least 57 concurrent requests
running, the mempool may overflow and mempool allocations may start
blocking until another entry is freed to the mempool. Because the same
thread is used to free entries to the mempool and allocate entries from
the mempool, this may result in a deadlock.
This patch changes it so that one mempool entry contains all 9 "struct
kcopyd_job" required to fulfill the whole request. The allocation is
done only once in dm_kcopyd_copy and no further mempool allocations are
done during request processing.
If dm_kcopyd_copy is not run in the completion thread, this
implementation is deadlock-free.
MIN_JOBS needs reducing accordingly and we've chosen to reduce it
further to 8.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Don't split SUB_JOB_SIZE jobs
If the job size equals SUB_JOB_SIZE, there is no point in splitting it.
Splitting it just unnecessarily wastes time, because the split job size
is SUB_JOB_SIZE too.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Integrity errors need to be passed to the owner of the integrity
metadata for processing. Consequently EILSEQ should be passed up the
stack.
Cc: stable@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds a check that a block device has a request function
defined before it is used. Otherwise, misconfiguration can cause an oops.
Because we are allowing devices with zero size e.g. an offline multipath
device as in commit 2cd54d9bed
("dm: allow offline devices") there needs to be an additional check
to ensure devices are initialised. Some block devices, like a loop
device without a backing file, exist but have no request function.
Reproducer is trivial: dm-mirror on unbound loop device
(no backing file on loop devices)
dmsetup create x --table "0 8 mirror core 2 8 sync 2 /dev/loop0 0 /dev/loop1 0"
and mirror resync will immediatelly cause OOps.
BUG: unable to handle kernel NULL pointer dereference at (null)
? generic_make_request+0x2bd/0x590
? kmem_cache_alloc+0xad/0x190
submit_bio+0x53/0xe0
? bio_add_page+0x3b/0x50
dispatch_io+0x1ca/0x210 [dm_mod]
? read_callback+0x0/0xd0 [dm_mirror]
dm_io+0xbb/0x290 [dm_mod]
do_mirror+0x1e0/0x748 [dm_mirror]
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Permit a target to support discards regardless of whether or not all its
underlying devices do.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Plan to remove floppy_disable_hlt in 2012, an ancient
workaround with comments that it should be removed.
This allows us to remove clutter and a run-time branch
from the idle code.
WARN_ONCE() on invocation until it is removed.
cc: x86@kernel.org
cc: stable@kernel.org # .39.x
Signed-off-by: Len Brown <len.brown@intel.com>
The workaround for AMD erratum 400 uses the term "c1e" falsely suggesting:
1. Intel C1E is somehow involved
2. All AMD processors with C1E are involved
Use the string "amd_c1e" instead of simply "c1e" to clarify that
this workaround is specific to AMD's version of C1E.
Use the string "e400" to clarify that the workaround is specific
to AMD processors with Erratum 400.
This patch is text-substitution only, with no functional change.
cc: x86@kernel.org
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ec->handle is set in ec_parse_device(), so don't bother to set it again.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_SxW returns an Integer containing the lowest D-state supported in state
Sx. If OSPM has not indicated that it supports _PR3, then the value “3”
corresponds to D3. If it has indicated _PR3 support, the value “3”
represents D3hot and the value “4” represents D3cold.
Linux does set _OSC._PR3, so we should fix it to expect that _SxW can
return 4.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Usually, there are multiple processors defined in ACPI table, for
example
Scope (_PR)
{
Processor (CPU0, 0x00, 0x00000410, 0x06) {}
Processor (CPU1, 0x01, 0x00000410, 0x06) {}
Processor (CPU2, 0x02, 0x00000410, 0x06) {}
Processor (CPU3, 0x03, 0x00000410, 0x06) {}
}
processor_physically_present(...) will be called to check whether those
processors are physically present.
Currently we have below codes in processor_physically_present,
cpuid = acpi_get_cpuid(...);
if ((cpuid == -1) && (num_possible_cpus() > 1))
return false;
return true;
In UP kernel, acpi_get_cpuid(...) always return -1 and
num_possible_cpus() always return 1, so
processor_physically_present(...) always returns true for all passed in
processor handles.
This is wrong for UP processor or SMP processor running UP kernel.
This patch removes the !SMP version of acpi_get_cpuid(), so both UP and
SMP kernel use the same acpi_get_cpuid function.
And for UP kernel, only processor 0 is valid.
https://bugzilla.kernel.org/show_bug.cgi?id=16548https://bugzilla.kernel.org/show_bug.cgi?id=16357
Tested-by: Anton Kochkov <anton.kochkov@gmail.com>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix kernel-doc warnings in scsi_proc.c:
Warning(drivers/scsi/scsi_proc.c:390): No description found for parameter 'dev'
Warning(drivers/scsi/scsi_proc.c:390): No description found for parameter 'data'
Warning(drivers/scsi/scsi_proc.c:390): Excess function parameter 's' description in 'always_match'
Warning(drivers/scsi/scsi_proc.c:390): Excess function parameter 'p' description in 'always_match'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With /sys/kernel/debug/acpi/custom_method root can write
to arbitrary memory and increase his priveleges, even if
these are restricted.
-> Make this an own debug .config option and warn about the
security issue in the config description.
-> Still keep acpi/debugfs.c which now only creates an empty
/sys/kernel/debug/acpi directory. There might be other
users of it later.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: rui.zhang@intel.com
Signed-off-by: Len Brown <len.brown@intel.com>
- Move param aml_debug_output to other params into sysfs.c
- Split acpi_debugfs_init to prepare custom_method to be
an own .config option and driver.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: rui.zhang@intel.com
Signed-off-by: Len Brown <len.brown@intel.com>
Cpuidle menu governor is using u32 as a temporary datatype for storing
nanosecond values which wrap around at 4.294 seconds. This causes errors
in predicted sleep times resulting in higher than should be C state
selection and increased power consumption. This also breaks cpuidle
state residency statistics.
cc: stable@kernel.org # .32.x through .39.x
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
perf: Fix SIGIO handling
perf top: Don't stop if no kernel symtab is found
perf top: Handle kptr_restrict
perf top: Remove unused macro
perf events: initialize fd array to -1 instead of 0
perf tools: Make sure kptr_restrict warnings fit 80 col terms
perf tools: Fix build on older systems
perf symbols: Handle /proc/sys/kernel/kptr_restrict
perf: Remove duplicate headers
ftrace: Add internal recursive checks
tracing: Update btrfs's tracepoints to use u64 interface
tracing: Add __print_symbolic_u64 to avoid warnings on 32bit machine
ftrace: Set ops->flag to enabled even on static function tracing
tracing: Have event with function tracer check error return
ftrace: Have ftrace_startup() return failure code
jump_label: Check entries limit in __jump_label_update
ftrace/recordmcount: Avoid STT_FUNC symbols as base on ARM
scripts/tags.sh: Add magic for trace-events for etags too
scripts/tags.sh: Fix ctags for DEFINE_EVENT()
x86/ftrace: Fix compiler warning in ftrace.c
...
* 'for-usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
Intel xhci: Limit number of active endpoints to 64.
Intel xhci: Ignore spurious successful event.
Intel xhci: Support EHCI/xHCI port switching.
Intel xhci: Add PCI id for Panther Point xHCI host.
xhci: STFU: Be quieter during URB submission and completion.
xhci: STFU: Don't print event ring dequeue pointer.
xhci: STFU: Remove function tracing.
xhci: Don't submit commands when the host is dead.
xhci: Clear stopped_td when Stop Endpoint command completes.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (33 commits)
x86: poll waiting for I/OAT DMA channel status
maintainers: add dma engine tree details
dmaengine: add TODO items for future work on dma drivers
dmaengine: Add API documentation for slave dma usage
dmaengine/dw_dmac: Update maintainer-ship
dmaengine: move link order
dmaengine/dw_dmac: implement pause and resume in dwc_control
dmaengine/dw_dmac: Replace spin_lock* with irqsave variants and enable submission from callback
dmaengine/dw_dmac: Divide one sg to many desc, if sg len is greater than DWC_MAX_COUNT
dmaengine/dw_dmac: set residue as total len in dwc_tx_status if status is !DMA_SUCCESS
dmaengine/dw_dmac: don't call callback routine in case dmaengine_terminate_all() is called
dmaengine: at_hdmac: pause: no need to wait for FIFO empty
pch_dma: modify pci device table definition
pch_dma: Support new device ML7223 IOH
pch_dma: Support I2S for ML7213 IOH
pch_dma: Fix DMA setting issue
pch_dma: modify for checkpatch
pch_dma: fix dma direction issue for ML7213 IOH video-in
dmaengine: at_hdmac: use descriptor chaining help function
dmaengine: at_hdmac: implement pause and resume in atc_control
...
Fix up trivial conflict in drivers/dma/dw_dmac.c
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
spi/spi_bfin_sport: new driver for a SPI bus via the Blackfin SPORT peripheral
spi/tle620x: add missing device_remove_file()
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/pch_gpio: Support new device ML7223
gpio: make gpio_{request,free}_array gpio array parameter const
GPIO: OMAP: move to drivers/gpio
GPIO: OMAP: move register offset defines into <plat/gpio.h>
gpio: Convert gpio_is_valid to return bool
gpio: Move the s5pc100 GPIO to drivers/gpio
gpio: Move the s5pv210 GPIO to drivers/gpio
gpio: Move the exynos4 GPIO to drivers/gpio
gpio: Move to Samsung common GPIO library to drivers/gpio
gpio/nomadik: add function to read GPIO pull down status
gpio/nomadik: show all pins in debug
gpio: move Nomadik GPIO driver to drivers/gpio
gpio: move U300 GPIO driver to drivers/gpio
langwell_gpio: add runtime pm support
gpio/pca953x: Add support for pca9574 and pca9575 devices
gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535
The 'max_part' parameter determines how many partitions are supported
on each nbd device. However the actual number can be changed to the
power of 2 minus 1 form during the module initialization as
alloc_disk() is called with (1 << part_shift) for some reason.
So adjust 'max_part' also at least for consistency with loop and brd.
It is exported via sysfs already, and a user should check this value
after module loading if [s]he wants to use that number correctly
(i.e. fdisk or something).
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Unlike kernel_sendmsg(), kernel_recvmsg() requires passing flags explicitly
via last parameter instead of struct msghdr.msg_flags. Therefore calls to
sock_xmit(lo, 0, ..., MSG_WAITALL) have not been processed properly by tcp
layer wrt. the flag. Fix it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* git://git.infradead.org/mtd-2.6: (97 commits)
mtd: kill CONFIG_MTD_PARTITIONS
mtd: remove add_mtd_partitions, add_mtd_device and friends
mtd: convert remaining users to mtd_device_register()
mtd: samsung onenand: convert to mtd_device_register()
mtd: omap2 onenand: convert to mtd_device_register()
mtd: txx9ndfmc: convert to mtd_device_register()
mtd: tmio_nand: convert to mtd_device_register()
mtd: socrates_nand: convert to mtd_device_register()
mtd: sharpsl: convert to mtd_device_register()
mtd: s3c2410 nand: convert to mtd_device_register()
mtd: ppchameleonevb: convert to mtd_device_register()
mtd: orion_nand: convert to mtd_device_register()
mtd: omap2: convert to mtd_device_register()
mtd: nomadik_nand: convert to mtd_device_register()
mtd: ndfc: convert to mtd_device_register()
mtd: mxc_nand: convert to mtd_device_register()
mtd: mpc5121_nfc: convert to mtd_device_register()
mtd: jz4740_nand: convert to mtd_device_register()
mtd: h1910: convert to mtd_device_register()
mtd: fsmc_nand: convert to mtd_device_register()
...
Fixed up trivial conflicts in
- drivers/mtd/maps/integrator-flash.c: removed in ARM tree
- drivers/mtd/maps/physmap.c: addition of afs partition probe type
clashing with removal of CONFIG_MTD_PARTITIONS
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
ARM: 6945/1: Add unwinding support for division functions
ARM: kill pmd_off()
ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks
ARM: 6943/1: mm: use TTBR1 instead of reserved context ID
ARM: 6942/1: mm: make TTBR1 always point to swapper_pg_dir on ARMv6/7
ARM: 6941/1: cache: ensure MVA is cacheline aligned in flush_kern_dcache_area
ARM: add sendmmsg syscall
ARM: 6863/1: allow hotplug on msm
ARM: 6832/1: mmci: support for ST-Ericsson db8500v2
ARM: 6830/1: mach-ux500: force PrimeCell revisions
ARM: 6829/1: amba: make hardcoded periphid override hardware
ARM: 6828/1: mach-ux500: delete SSP PrimeCell ID
ARM: 6827/1: mach-netx: delete hardcoded periphid
ARM: 6940/1: fiq: Briefly document driver responsibilities for suspend/resume
ARM: 6938/1: fiq: Refactor {get,set}_fiq_regs() for Thumb-2
ARM: 6914/1: sparsemem: fix highmem detection when using SPARSEMEM
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM
at91: drop at572d940hf support
at91rm9200: introduce at91rm9200_set_type to specficy cpu package
at91: drop boot_params and PLAT_PHYS_OFFSET
...
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
gpio_{request,free}_array should not (and do not) modify the passed gpio
array, so make the parameter const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Panther Point chipset has an xHCI host controller that has a limit to
the number of active endpoints it can handle. Ideally, it would signal
that it can't handle anymore endpoints by returning a Resource Error for
the Configure Endpoint command, but they don't. Instead it needs software
to keep track of the number of active endpoints, across configure endpoint
commands, reset device commands, disable slot commands, and address device
commands.
Add a new endpoint context counter, xhci_hcd->num_active_eps, and use it
to track the number of endpoints the xHC has active. This gets a little
tricky, because commands to change the number of active endpoints can
fail. This patch adds a new xHCI quirk for these Intel hosts, and the new
code should not have any effect on other xHCI host controllers.
Fail a new device allocation if we don't have room for the new default
control endpoint. Use the endpoint ring pointers to determine what
endpoints were active before a Reset Device command or a Disable Slot
command, and drop those once the command completes.
Fail a configure endpoint command if it would add too many new endpoints.
We have to be a bit over zealous here, and only count the number of new
endpoints to be added, without subtracting the number of dropped
endpoints. That's because a second configure endpoint command for a
different device could sneak in before we know if the first command is
completed. If the first command dropped resources, the host controller
fails the command for some reason, and we're nearing the limit of
endpoints, we could end up oversubscribing the host.
To fix this race condition, when evaluating whether a configure endpoint
command will fix in our bandwidth budget, only add the new endpoints to
xhci->num_active_eps, and don't subtract the dropped endpoints. Ignore
changed endpoints (ones that are dropped and then re-added), as that
shouldn't effect the host's endpoint resources. When the configure
endpoint command completes, subtract off the dropped endpoints.
This may mean some configuration changes may temporarily fail, but it's
always better to under-subscribe than over-subscribe resources.
(Originally my plan had been to push the resource allocation down into the
ring allocation functions. However, that would cause us to allocate
unnecessary resources when endpoints were changed, because the xHCI driver
allocates a new ring for the changed endpoint, and only deletes the old
ring once the Configure Endpoint command succeeds. A further complication
would have been dealing with the per-device endpoint ring cache.)
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The xHCI host controller in the Panther Point chipset sometimes produces
spurious events on the event ring. If it receives a short packet, it
first puts a Transfer Event with a short transfer completion code on the
event ring. Then it puts a Transfer Event with a successful completion
code on the ring for the same TD. The xHCI driver correctly processes the
short transfer completion code, gives the URB back to the driver, and then
prints a warning in dmesg about the spurious event. These warning
messages really fill up dmesg when an HD webcam is plugged into xHCI.
This spurious successful event behavior isn't technically disallowed by
the xHCI specification, so make the xHCI driver just ignore the spurious
completion event.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The Intel Panther Point chipsets contain an EHCI and xHCI host controller
that shares some number of skew-dependent ports. These ports can be
switched from the EHCI to the xHCI host (and vice versa) by a hardware MUX
that is controlled by registers in the xHCI PCI configuration space. The
USB 3.0 SuperSpeed terminations on the xHCI ports can be controlled
separately from the USB 2.0 data wires.
This switchover mechanism is there to support users who do a custom
install of certain non-Linux operating systems that don't have official
USB 3.0 support. By default, the ports are under EHCI, SuperSpeed
terminations are off, and USB 3.0 devices will show up under the EHCI
controller at reduced speeds. (This was more palatable for the marketing
folks than having completely dead USB 3.0 ports if no xHCI drivers are
available.) Users should be able to turn on xHCI by default through a
BIOS option, but users are happiest when they don't have to change random
BIOS settings.
This patch introduces a driver method to switchover the ports from EHCI to
xHCI before the EHCI driver finishes PCI enumeration. We want to switch
the ports over before the USB core has the chance to enumerate devices
under EHCI, or boot from USB mass storage will fail if the boot device
connects under EHCI first, and then gets disconnected when the port
switches over to xHCI.
Add code to the xHCI PCI quirk to switch the ports from EHCI to xHCI. The
PCI quirks code will run before any other PCI probe function is called, so
this avoids the issue with boot devices.
Another issue is with BIOS behavior during system resume from hibernate.
If the BIOS doesn't support xHCI, it may switch the devices under EHCI to
allow use of the USB keyboard, mice, and mass storage devices. It's
supposed to remember the value of the port routing registers and switch
them back when the OS attempts to take control of the xHCI host controller,
but we all know not to trust BIOS writers.
Make both the xHCI driver and the EHCI driver attempt to switchover the
ports in their PCI resume functions. We can't guarantee which PCI device
will be resumed first, so this avoids any race conditions. Writing a '1'
to an already set port switchover bit or a '0' to a cleared port switchover
bit should have no effect.
The xHCI PCI configuration registers will be documented in the EDS-level
chipset spec, which is not public yet. I have permission from legal and
the Intel chipset group to release this patch early to allow good Linux
support at product launch. I've tried to document the registers as much
as possible, so please let me know if anything is unclear.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Kill ratelimit.h dependency in linux/net.h
net: Add linux/sysctl.h includes where needed.
net: Kill ether_table[] declaration.
inetpeer: fix race in unused_list manipulations
atm: expose ATM device index in sysfs
IPVS: bug in ip_vs_ftp, same list heaad used in all netns.
bug.h: Move ratelimit warn interfaces to ratelimit.h
bonding: cleanup module option descriptions
net:8021q:vlan.c Fix pr_info to just give the vlan fullname and version.
net: davinci_emac: fix dev_err use at probe
can: convert to %pK for kptr_restrict support
net: fix ETHTOOL_SFEATURES compatibility with old ethtool_ops.set_flags
netfilter: Fix several warnings in compat_mtw_from_user().
netfilter: ipset: fix ip_set_flush return code
netfilter: ipset: remove unused variable from type_pf_tdel()
netfilter: ipset: Use proper timeout value to jiffies conversion
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] v1.88 DM04/QQBOX Move remote to use rc_core dvb-usb-remote
[media] Add missing include guard to header file
[media] Inlined functions should be static
[media] Remove invalid parameter description
[media] cpia2: fix warning about invalid trigraph sequence
[media] s5p-csis: Add missing dependency on PLAT_S5P
[media] gspca/kinect: wrap gspca_debug with GSPCA_DEBUG
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function
[media] uvcvideo: Connect video devices to media entities
[media] uvcvideo: Register subdevices for each entity
[media] uvcvideo: Register a v4l2_device
[media] add V4L2-PIX-FMT-SRGGB12 & friends to docbook
[media] Documentation/DocBook: Rename media fops xml files
[media] Media DocBook: fix validation errors
[media] wl12xx: g_volatile_ctrl fix: wrong field set
[media] fix kconfig dependency warning for VIDEO_TIMBERDALE
[media] dm1105: GPIO handling added, I2C on GPIO added, LNB control through GPIO reworked
[media] Add support for M-5MOLS 8 Mega Pixel camera ISP
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (42 commits)
regulator: Fix _regulator_get_voltage if get_voltage callback is NULL
USB: TWL6025 allow different regulator name
REGULATOR: TWL6025: add support to twl-regulator
regulator: twl6030: do not write to _GRP for regulator disable
regulator: twl6030: do not write to _GRP for regulator enable
TPS65911: Comparator: Add comparator driver
TPS65911: Add support for added GPIO lines
GPIO: TPS65910: Move driver to drivers/gpio/
TPS65911: Add new irq definitions
regulator: tps65911: Add new chip version
MFD: TPS65910: Add support for TPS65911 device
regulator: Fix off-by-one value range checking for mc13xxx_regulator_get_voltage
regulator: mc13892: Fix voltage unit in test case.
regulator: Remove MAX8997_REG_BUCK1DVS/MAX8997_REG_BUCK2DVS/MAX8997_REG_BUCK5DVS macros
mfd: Fix off-by-one value range checking for tps65910_i2c_write
regulator: Only apply voltage constraints from consumers that set them
regulator: If we can't configure optimum mode we're always in the best one
regulator: max8997: remove useless code
regulator: Fix memory leak in max8998_pmic_probe failure path
regulator: Fix desc_id for tps65023/6507x/65910
...
* git://git.infradead.org/battery-2.6:
PXA: Use dev_pm_ops in z2_battery
ds2760_battery: Fix rated capacity of the hx4700 1800mAh battery
ds2760_battery: Fix indexing of the 4 active full EEPROM registers
power: Make test_power driver more dynamic.
bq27x00_battery: Name of cycle count property
max8903_charger: Add GENERIC_HARDIRQS as a dependency (fixes S390 build)
ARM: RX-51: Enable isp1704 power on/off
isp1704_charger: Allow board specific powering routine
gpio-charger: Add gpio_charger_resume
power_supply: Add driver for MAX8903 charger
The AR9287 calibration code was not being called because of an
incorrect MAC revision check.
This forced the AR9287 to use the AR9285 initial calibration code and
bypass the AR9287 code entirely.
Signed-off-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We make oldconfig every time when a new kernel arrives, but
if we don't have such a device(I guess this is the most common
case for a new device), the default value should be 'n' so
that the kernel size we build doesn't grow up too much quickly.
For anyone who has the device, it is OK for them to turn it on
by themselves.
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rx_status.band is used uninitialized, what disallow to work on 5GHz .
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acer WMID_GUID1/2 method's return value was declared to integer
type on Gateway notebook.
So, add this patch for support integer return type.
Reference: bko#33032
https://bugzilla.kernel.org/show_bug.cgi?id=33032
Tested on Gateway NV5909H laptop
Tested-by: Filipus Klutiero <chealer@gmail.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There have section mismatch warning message shows up when building
the kernel with make CONFIG_DEBUG_SECTION_MISMATCH=y.
The problem is the load_scm_model_init() calls msi_laptop_input_setup()
which is an __init function, but load_scm_model_init() lacks a __init
annotation.
This patch add __init on load_scm_model_init() to avoid warning message.
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Have many Acer notebooks' BIOS already support new WMID_GUID3 method.
On those machines, that will be better set communication device by
evaluate WMID_GUID3 method.
Tested on Acer Travelmate 8572
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acer WMID_GUID1/2 method's return buffer was declared to 64-bits
on some Acer notebook, but WMI method only use 32-bits in return
buffer.
So, add this patch for allow 64-bits return buffer.
Reference: bko#34142
https://bugzilla.kernel.org/show_bug.cgi?id=34142
Tested on Acer Travelmate 5735Z-452G32Mnss
Tested-by: Melchior FRANZ <melchior.franz@gmail.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
That will be better to check the existence of internal 3G device when
we set threeg capability and generate killswitch for threeg. It can
avoid userland access 3G rfkill but the machine doesn't have internal
3G device.
Reference: bko#32862
https://bugzilla.kernel.org/show_bug.cgi?id=32862
Tested on Acer Aspire 8930G, Acer Travelmate 8572
Tested-by: Hector Martin <hector@marcansoft.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
variable handle is not used in these two functions,
just delete them.
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
On an Acer Travelmate 5735Z-452G32Mnss the WLAN-enable/disable key
doesn't send 0x1 as acpi event key code, but 0x3. This patch also
makes the module ignore hotkey acpi events for functions that are
already handled without. This avoids warning message "keyboard:
can't emulate rawmode for keycode 240".
Signed-off-by: Melchior FRANZ <mfranz@aon.at>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
