Commit Graph

122 Commits

Author SHA1 Message Date
Darrick J. Wong
c0b4e3ab0c adt7462: new hwmon driver
New driver to play with.  As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors.  This driver has been tested on an IntelliStation Z30.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-12 17:17:17 -08:00
Pavel Machek
455fbdd376 LIS3LV02Dx Accelerometer driver
This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard").  It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.

This driver was first written by Yan Burman.  Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now).  Pavel Machek removed few more features and switched locking from
semaphore to mutex.

Several people have contributed to the database of the axes.

[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API]
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Yan Burman <burman.yan@gmail.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-12 17:17:17 -08:00
Jean Delvare
97ae60bb38 hwmon: (lm90) Add support for the LM99 16 degree offset
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
2008-10-26 17:04:39 +01:00
Darrick J. Wong
d664a4809e hwmon: (adt7470) Add documentation
Add at least the bare minimum of documentation for this chip.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:20 +02:00
Jean Delvare
10c08f937d hwmon: (w83781d) Additional information about AS99127F PWM
This information was provided in lm-sensors ticket #2350:
http://www.lm-sensors.org/ticket/2350

This is IMHO still not enough to be able to safely implement fan
control support for the AS99127F, but this is valuable information so
I am adding it to the documentation.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:18 +02:00
Jean Delvare
6aa693b852 hwmon: Drop dead links to old National Semiconductor chip datasheets
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:17 +02:00
Marc Hulsman
a5a4598cd2 hwmon: (w83791d) add support for thermal cruise mode
Add support to set target temperature and tolerance for thermal
cruise mode.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:17 +02:00
Marc Hulsman
b5938f8c4a hwmon: (w83791d) add pwm_enable support
Add support for pwm_enable.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:17 +02:00
Marc Hulsman
6495ce1840 hwmon: (w83791d) add manual PWM support
Add PWM manual control.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:17 +02:00
Jean Delvare
4ed1077953 hwmon: (it87) Fix thermal sensor type values
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.

Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2008-10-17 17:51:16 +02:00
Jean Delvare
34e7dc6ca4 hwmon: (lm85) Implement the standard PWM frequency interface
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17 17:51:13 +02:00
Ben Hutchings
47064d645b hwmon: (lm87) Add support for configuration through platform_data
The lm87 driver normally assumes that firmware configured the chip
correctly.  Since this is not always the case, alllow platform code to
set the channel register value via platform_data.  All other
configuration registers can be changed after driver initialisation.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:12 +02:00
Ben Hutchings
271dabf5bb hwmon: (lm90) Support MAX6646, MAX6647 and MAX6649
These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:11 +02:00
Nate Case
23b2d4778a hwmon: (lm90) Support ADT7461 in extended mode
Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC.  Adjust the
register conversion functions accordingly.

Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
2008-10-17 17:51:10 +02:00
Jean Delvare
a874a10cf0 hwmon: (lm90) Update datasheet links
Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
2008-10-17 17:51:10 +02:00
Jean Delvare
f65e17086f hwmon: (lm90) Support the extra resolution bits of MAX6657
The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
2008-10-17 17:51:09 +02:00
Darrick J. Wong
c73c556c1a hwmon: (adt7473) Fix some bogosity in documentation file
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-09 15:33:58 +02:00
Darrick J. Wong
ddedc658fc hwmon: Define sysfs interface for energy consumption register
Describe the sysfs files that were introduced in the ibmaem driver.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-09 15:33:58 +02:00
Darrick J. Wong
eb93b7df7e ibmaem: update the documentation to reflect the current name
Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-15 08:35:44 -07:00
Andrew Paprocki
816d8c6a25 hwmon: (it87) Support for 16-bit fan reading in it8705 >= rev 0x03
The it8705 chip supports 16-bit fan tachometers in revisions at least
>= 0x03 (Version G). This patch enables 16-bit fan readings on all
revisions >= 0x03 just like the it8712, it8716, and it8718 chips.

Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-08-06 22:41:06 +02:00
Andrew Paprocki
0475169c13 hwmon: (it87) Support for 16-bit fan reading in it8712 >= rev 0x07
The it8712 chip supports 16-bit fan tachometers in revisions >= 0x07.
Revisions >= 0x08 dropped support for 8-bit fan divisor registers. The
patch enables 16-bit fan readings on all revisions >= 0x07 just like
the it8716 and it8718 chips.

Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-08-06 22:41:06 +02:00
Jean Delvare
2f8ea97a45 hwmon: (w83627hf) Drop reset module parameter
Drop the reset parameter of the w83627hf driver. It seems it wasn't
that useful. It was dropped from the Linux 2.4 version of this driver
back in July 2004.

The only users who have reported that they were still using this
parameter, needed it to switch the chip from automatic fan speed
control back to manual mode. Now that the driver creates pwmN_enable
sysfs files, users will be able to use these files instead, which is
way less agressive.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dominik Geyer <dominik.geyer@gmx.de>
2008-08-06 22:41:04 +02:00
Marc Hulsman
ad02ad85cf hwmon: (w83791d) Use fan divisor bits from vbat register
Update w83791d with fan bits in vbat mon register (7.48 of the
datasheet). This change allows all fans to have a divisor of 128, 
and fixes a problem with incorrectly reported fan speeds. 

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-08-06 22:41:04 +02:00
Juerg Haefliger
549edb8332 hwmon: (dme1737) Add support for the SMSC SCH5027
Add support for the SCH5027. The differences to the DME1737 are:
- No support for programmable temp offsets
- In auto mode, PWM outputs stay on min value if temp goes below low threshold
  and can't be programmed to fully turn off
- Different voltage scaling
- No VID input

Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-08-06 22:41:03 +02:00
Jean Delvare
dd1ac5384a hwmon: (lm85) Drop dead code
Drop a lot of useless register defines, conversion macros, data structure
members and update code. All these register values were read from the
device but nothing is done out of them, so this is all dead code in
practice.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-07-31 23:44:03 -04:00
Juerg Haefliger
92430b6feb hwmon: (dme1737) probe all addresses
This patch adds a module load parameter to enable probing of
non-standard LPC addresses 0x162e and 0x164e when scanning for supported
ISA chips.

Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-07-31 23:44:02 -04:00
Jean Delvare
125ff8087f hwmon: Update the sysfs interface documentation
* Document the characteristics of libsensors 3.0.0 and 3.0.1.
* The sysfs interface is no longer subject to changes.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-06-19 06:50:31 -04:00
Darrick J. Wong
8808a793f0 ibmaem: new driver for power/energy/temp meters in IBM System X hardware
This driver reads IBM Active Energy Manager energy/temperature/power
sensors on IBM System X hardware.

[akpm@linux-foundation.org: fix printk warnings]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:08 -07:00
Darrick J. Wong
241937b863 adt7473: minor documentation update
Add a sentence about when fan speed increases to maximum.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-13 08:02:24 -07:00
Jean Delvare
4040c415f5 hwmon: (w83l785ts) Don't ask the user to report failures
There's nothing we can do about read errors on the W83L785TS-S, so
don't ask the user to report them.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-04-27 09:23:11 -04:00
Darrick J. Wong
57df46d6d9 hwmon: New driver for Analog Devices ADT7473 sensor chip
This driver reports voltage, temperature and fan sensor readings
on an ADT7473 chip.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-18 21:51:29 -05:00
Rudolf Marek
ae770152c8 hwmon: (coretemp) Add Penryn CPU to coretemp
This patch adds support for family 0x17, which has Penryn Core. It should also
cover the 8 cores Xeons.

Can someone test please? I think it should work.

Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-17 22:08:37 -05:00
Rudolf Marek
6369a2887a hwmon: (coretemp) Add maximum cooling temperature readout
Following patch will add reporting of maximum temperature, at which all fans
should spin full speed. It may be non-physical temperature on Desktop/Server CPUs.

Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-17 10:21:39 -05:00
Jean Delvare
cbe311f2a4 hwmon: (w83627ehf) The W83627DHG has 8 VID pins
While the W83627EHF/EHG has only 6 VID pins, the W83627DHG has 8 VID
pins, to support VRD 11.0. Add support for this.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-07 20:39:45 -05:00
Steve Hardy
5812f9283e hwmon: Add support for Texas Instruments/Burr-Brown ADS7828
Signed-off-by: Steve Hardy <steve@linuxrealtime.co.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-07 20:39:44 -05:00
Jean Delvare
05663368d2 hwmon: (w83781d) Drop W83627HF support
The W83627HF hardware monitoring features are supported by the
w83627hf driver for several years now. Support by the w83781d has
been advertised as deprecated 6 months ago, it's about time to see
it go.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-07 20:39:43 -05:00
Jean Delvare
f1d8e33263 hwmon: (it87) Discard a dead e-mail address
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-07 20:39:42 -05:00
Jean Delvare
ec1d86c457 hwmon: Update the lm-sensors website address
It's about time to reflect the move of the lm-sensors project to
lm-sensors.org.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-07 20:39:42 -05:00
Jean Delvare
c7fa373796 hwmon: (lm87) Add support for the Analog Devices ADM1024
It happens that the Analog Devices ADM1024 is fully compatible with
the National Semiconductor LM87, so support for the former can easily
be added to the lm87 driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-07 20:39:40 -05:00
Kevin Lo
85f03bccd6 hwmon: Add support for Winbond W83L786NG/NR
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-07 20:39:40 -05:00
Jean Delvare
6722feada7 hwmon: (lm78/w83781d) Probe fewer I2C addresses
We've never seen any device supported by the lm78 or w83781d driver at
addresses 0x20-0x27, so let's stop probing these addresses. Extra probes cost
time, and have potential for confusing or misdetecting other I2C devices.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-02-07 20:39:40 -05:00
Darrick J. Wong
38fb56a223 hwmon: Add power meter spec to Documentation/hwmon/sysfs-interface
Update the hwmon sysfs interface documentation to include a specification
for power meters.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-11-08 08:42:45 -05:00
Juerg Haefliger
e95c237d78 hwmon: (dme1737) Add sch311x support
This patch adds support for the SMSC SCH3112, SCH3114, and SCH3116 Super-I/O
chips. These chips feature identical hardware monitoring capabilites with the
expection that some of the fan inputs and pmw outputs don't exist.

The hardware monitoring features of the SCH311x chips can only be accessed via
the ISA bus. The driver therefore registers as a platform driver, if such a
chip is detected.

Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-10-10 22:47:13 -04:00
Rudolf Marek
c940336b44 hwmon: (coretemp) Add support for Celeron 4xx
This patch adds support for the Celeron 4xx based on Core 2 core.

Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-10-09 22:56:32 -04:00
Jean Delvare
5fbea518da hwmon: Fix the code examples in documentation
Fix a bug in the code examples, make them comply with CodingStyle,
and indent them for a better redability.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-10-09 22:56:32 -04:00
Hans de Goede
2ed4263308 hwmon: update sysfs interface document - error handling
Here is a patch adding some text to the sysfs interface documentation on how
settings written to sysfs attributes should be handled, focussing mainly on
error handling. This version incorperates Jean's latest comments.

Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-10-09 22:56:31 -04:00
Jean Delvare
428a7039c5 hwmon: (lm78) Add individual alarm files
Add individual alarm files to the lm78 driver, these are needed by
the next version of libsensors.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-10-09 22:56:31 -04:00
Jean Delvare
c7f1f7166a hwmon: (it87) Add support for fan4 and fan5
Add support for the IT8716F and IT8718F fan4 and fan5. The late
revisions of the IT8712F have these too but support is harder to add
and nobody asked for it yet, so I didn't include it.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-10-09 22:56:30 -04:00
Charles Spirakis
6438312367 hwmon: (w83791d) new sysfs beep/alarm methodology
Add new sysfs alarm methodology to w83791d driver

Signed-off-by: Charles Spirakis <bezaur@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-10-09 22:56:30 -04:00
Jean Delvare
176544dc55 hwmon: Update the sysfs interface documentation
* Document the name attribute.
* Document the *_label attributes.
* Drop "typical usage" lists, they no longer match the reality.
* Drop non hardware-monitoring related entries.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2007-10-09 22:56:29 -04:00