The test va_128TBswitch.c exercises a feature only supported on PPC and
x86_64, but it's run on other 64-bit archs as well. Before this patch,
the test did nothing and returned 0 for KSFT_PASS. This patch makes it
return the KSFT codes from kselftest.h, including KSFT_SKIP when
appropriate.
Verified on arm64 and x86_64.
Link: https://lkml.kernel.org/r/20220704123813.427625-1-adam@wowsignal.io
Signed-off-by: Adam Sindelar <adam@wowsignal.io>
Cc: David Vernet <void@manifault.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The send_signal/send_signal_tracepoint is pretty flaky, with at least
one failure in every ten runs on a few attempts I've tried it:
> test_send_signal_common:PASS:pipe_c2p 0 nsec
> test_send_signal_common:PASS:pipe_p2c 0 nsec
> test_send_signal_common:PASS:fork 0 nsec
> test_send_signal_common:PASS:skel_open_and_load 0 nsec
> test_send_signal_common:PASS:skel_attach 0 nsec
> test_send_signal_common:PASS:pipe_read 0 nsec
> test_send_signal_common:PASS:pipe_write 0 nsec
> test_send_signal_common:PASS:reading pipe 0 nsec
> test_send_signal_common:PASS:reading pipe error: size 0 0 nsec
> test_send_signal_common:FAIL:incorrect result unexpected incorrect result: actual 48 != expected 50
> test_send_signal_common:PASS:pipe_write 0 nsec
> #139/1 send_signal/send_signal_tracepoint:FAIL
The reason does not appear to be a correctness issue in the strict
sense. Rather, we merely do not receive the signal we are waiting for
within the provided timeout.
Let's bump the timeout by a factor of ten. With that change I have not
been able to reproduce the failure in 150+ iterations. I am also sneaking
in a small simplification to the test_progs test selection logic.
Signed-off-by: Daniel Müller <deso@posteo.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20220727182955.4044988-1-deso@posteo.net
Add IPv4 and IPv6 test cases that ensure that we are not leaking a
reference on the nexthop device when we are unable to delete its
associated route.
Without the fix in a previous patch ("netdevsim: fib: Fix reference
count leak on route deletion failure") both test cases get stuck,
waiting for the reference to be released from the dummy device [1][2].
[1]
unregister_netdevice: waiting for dummy1 to become free. Usage count = 5
leaked reference.
fib_check_nh+0x275/0x620
fib_create_info+0x237c/0x4d30
fib_table_insert+0x1dd/0x1d20
inet_rtm_newroute+0x11b/0x200
rtnetlink_rcv_msg+0x43b/0xd20
netlink_rcv_skb+0x15e/0x430
netlink_unicast+0x53b/0x800
netlink_sendmsg+0x945/0xe40
____sys_sendmsg+0x747/0x960
___sys_sendmsg+0x11d/0x190
__sys_sendmsg+0x118/0x1e0
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[2]
unregister_netdevice: waiting for dummy1 to become free. Usage count = 5
leaked reference.
fib6_nh_init+0xc46/0x1ca0
ip6_route_info_create+0x1167/0x19a0
ip6_route_add+0x27/0x150
inet6_rtm_newroute+0x161/0x170
rtnetlink_rcv_msg+0x43b/0xd20
netlink_rcv_skb+0x15e/0x430
netlink_unicast+0x53b/0x800
netlink_sendmsg+0x945/0xe40
____sys_sendmsg+0x747/0x960
___sys_sendmsg+0x11d/0x190
__sys_sendmsg+0x118/0x1e0
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This selftest is designed for testing the H.L2Encaps.Red behavior. It
instantiates a virtual network composed of several nodes: hosts and SRv6
routers. Each node is realized using a network namespace that is
properly interconnected to others through veth pairs.
The test considers SRv6 routers implementing a L2 VPN leveraged by hosts
for communicating with each other. Such routers make use of the SRv6
H.L2Encaps.Red behavior for applying SRv6 policies to L2 traffic coming
from hosts.
The correct execution of the behavior is verified through reachability
tests carried out between hosts belonging to the same VPN.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
This selftest is designed for testing the H.Encaps.Red behavior. It
instantiates a virtual network composed of several nodes: hosts and SRv6
routers. Each node is realized using a network namespace that is
properly interconnected to others through veth pairs.
The test considers SRv6 routers implementing L3 VPNs leveraged by hosts
for communicating with each other. Such routers make use of the SRv6
H.Encaps.Red behavior for applying SRv6 policies to L3 traffic coming
from hosts.
The correct execution of the behavior is verified through reachability
tests carried out between hosts belonging to the same VPN.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do 'make -C tools/testing/memblock', get the following errors:
memblock.o: In function `memblock_find_in_range.constprop.9':
memblock.c:(.text+0x4651): undefined reference to `pr_warn_ratelimited'
memblock.o: In function `memblock_mark_mirror':
memblock.c:(.text+0x7171): undefined reference to `mirrored_kernelcore'
Fixes: 902c2d9158 ("memblock: Disable mirror feature if kernelcore is not specified")
Fixes: 14d9a675fd ("mm: Ratelimited mirrored memory related warning messages")
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
Tested-by: Ma Wupeng <mawupeng1@huawei.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lore.kernel.org/r/1658916453-26312-1-git-send-email-liuxp11@chinatelecom.cn
Add a handful of memory randomizations and precise length checks.
Nothing is really broken here, I did this to increase confidence
when debugging. It does fix a GCC warning, tho. Apparently GCC
recognizes that memory needs to be initialized for send() but
does not recognize that for write().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a command line option to dirty_log_perf_test to run vCPUs for the
entire duration of disabling dirty logging. By default, the test stops
running runs vCPUs before disabling dirty logging, which is faster but
less interesting as it doesn't stress KVM's handling of contention
between page faults and the zapping of collapsible SPTEs. Enabling the
flag also lets the user verify that KVM is indeed rebuilding zapped SPTEs
as huge pages by checking KVM's pages_{1g,2m,4k} stats. Without vCPUs to
fault in the zapped SPTEs, the stats will show that KVM is zapping pages,
but they never show whether or not KVM actually allows huge pages to be
recreated.
Note! Enabling the flag can _significantly_ increase runtime, especially
if the thread that's disabling dirty logging doesn't have a dedicated
pCPU, e.g. if all pCPUs are used to run vCPUs.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220715232107.3775620-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ISA states: "when ACC[i] contains defined data, the contents of VSRs
4×i to 4×i+3 are undefined until either a VSX Move From ACC instruction
is used to copy the contents of ACC[i] to VSRs 4×i to 4×i+3 or some other
instruction directly writes to one of these VSRs." We aren't doing this.
This test only works on Power10 because the hardware implementation
happens to map ACC0 to VSRs 0-3, but will fail on any other implementation
that doesn't do this. So add xxmfacc between writing to the accumulator
and accessing the VSRs.
Fixes: 3527e1ab9a ("selftests/powerpc: Add matrix multiply assist (MMA) test")
Signed-off-by: Rashmica Gupta <rashmica@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220617043935.428083-1-rashmica@linux.ibm.com
clang has -Wconstant-conversion by default, and the constant 0xAAAAAAAAA
(9 As) being converted to an int, which is generally 32 bits, results
in the compile warning:
clang -Wl,-no-as-needed -Wall -isystem ../../../../usr/include/ -lpthread seccomp_bpf.c -lcap -o seccomp_bpf
seccomp_bpf.c:812:67: warning: implicit conversion from 'long' to 'int' changes value from 45812984490 to -1431655766 [-Wconstant-conversion]
int kill = kill_how == KILL_PROCESS ? SECCOMP_RET_KILL_PROCESS : 0xAAAAAAAAA;
~~~~ ^~~~~~~~~~~
1 warning generated.
-1431655766 is the expected truncation, 0xAAAAAAAA (8 As), so use
this directly in the code to avoid the warning.
Fixes: 3932fcecd9 ("selftests/seccomp: Add test for unknown SECCOMP_RET kill behavior")
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220526223407.1686936-1-zhuyifei@google.com
So far the vmtest.sh script, which can be used as a convenient way to
run bpf selftests, has obtained the kernel config safe to use for
testing from the libbpf/libbpf GitHub repository [0].
Given that we now have included this configuration into this very
repository, we can just consume it from here as well, eliminating the
necessity of remote accesses.
With this change we adjust the logic in the script to use the
configuration from below tools/testing/selftests/bpf/configs/ instead
of pulling it over the network.
[0] https://github.com/libbpf/libbpf
Signed-off-by: Daniel Müller <deso@posteo.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Mykola Lysenko <mykolal@fb.com>
Link: https://lore.kernel.org/bpf/20220727001156.3553701-4-deso@posteo.net
This change makes sure to sort the existing minimal kernel configuration
containing options required for running BPF selftests alphabetically.
Doing so will make it easier to diff it against other configurations,
which in turn helps with maintaining disjunct config files that build on
top of each other. It also helped identify the CONFIG_IPV6_GRE being set
twice and removes one of the occurrences.
Lastly, we change NET_CLS_BPF from 'm' to 'y'. Having this option as 'm'
will cause failures of the btf_skc_cls_ingress selftest.
Signed-off-by: Daniel Müller <deso@posteo.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Mykola Lysenko <mykolal@fb.com>
Link: https://lore.kernel.org/bpf/20220727001156.3553701-2-deso@posteo.net
Once line card is activated, check the FW version and PSID are exposed.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Once line card is provisioned, check if HW revision and INI version
are exposed on associated nested auxiliary device.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous commit fixed a bug in the bpf_skb_set_tunnel_key helper to
avoid dropping packets whose outer source IP address isn't assigned to a
host interface. This commit changes the corresponding selftest to not
assign the outer source IP address to an interface.
Not assigning the source IP to an interface causes two issues in the
existing test:
1. The ARP requests will fail for that IP address so we need to add the
ARP entry manually.
2. The encapsulated ICMP echo reply traffic will not reach the VXLAN
device. It will be dropped by the stack before, because the
outer destination IP is unknown.
To solve 2., we have two choices. Either we perform decapsulation
ourselves in a BPF program attached at veth1 (the base device for the
VXLAN device), or we switch the outer destination address when we
receive the packet at veth1, such that the stack properly demultiplexes
it to the VXLAN device afterward.
This commit implements the second approach, where we switch the outer
destination address from the unassigned IP address to the assigned one,
only for VXLAN traffic ingressing veth1.
Then, at the vxlan device, the BPF program that checks the output of
bpf_skb_get_tunnel_key needs to be updated as the expected local IP
address is now the unassigned one.
Signed-off-by: Paul Chaignon <paul@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/4addde76eaf3477a58975bef15ed2788c44e5f55.1658759380.git.paul@isovalent.com
After all the soft validation of the region has completed, convey the
region configuration to hardware while being careful to commit decoders
in specification mandated order. In addition to programming the endpoint
decoder base-address, interleave ways and granularity, the switch
decoder target lists are also established.
While the kernel can enforce spec-mandated commit order, it can not
enforce spec-mandated reset order. For example, the kernel can't stop
someone from removing an endpoint device that is occupying decoderN in a
switch decoder where decoderN+1 is also committed. To reset decoderN,
decoderN+1 must be torn down first. That "tear down the world"
implementation is saved for a follow-on patch.
Callback operations are provided for the 'commit' and 'reset'
operations. While those callbacks may prove useful for CXL accelerators
(Type-2 devices with memory) the primary motivation is to enable a
simple way for cxl_test to intercept those operations.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784338418.1758207.14659830845389904356.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently the ptrace-gpr test only tests the GET/SET(FP)REGS ptrace
APIs. But there's an alternate (older) API, called PEEK/POKEUSR.
Add some minimal testing of PEEK/POKEUSR of the FPRs. This is sufficient
to detect the bug that was fixed recently in the 32-bit ptrace FPR
handling.
Depends-on: 8e12784444 ("powerpc/32: Fix overread/overwrite of thread_struct via ptrace")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220627140239.2464900-13-mpe@ellerman.id.au
The ptrace-gpr test uses fixed values to test that registers can be
read/written via ptrace. In particular it sets all GPRs to 1, which
means the test could miss some types of bugs - eg. if the kernel was
only returning the low word.
So generate some random values at startup and use those instead.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220627140239.2464900-12-mpe@ellerman.id.au
The ptrace-gpr test includes some inline asm to load GPR and FPR
registers. It then goes back to C to wait for the parent to trace it and
then checks register contents.
The split between inline asm and C is fragile, it relies on the compiler
not using any non-volatile GPRs after the inline asm block. It also
requires a very large and unwieldy inline asm block.
So convert the logic to set registers, wait, and store registers to a
single asm function, meaning there's no window for the compiler to
intervene.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220627140239.2464900-10-mpe@ellerman.id.au
Some of the ptrace tests check the contents of floating pointer
registers. Currently these use float, which is always 4 bytes, but the
ptrace API supports saving/restoring 8 bytes per register, so switch to
using doubles to exercise the code more fully.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220627140239.2464900-8-mpe@ellerman.id.au
Currently all ptrace tests are built 64-bit and with TM enabled.
Only the TM tests need TM enabled, so split those out into a separate
variable so that can be specified precisely.
Split the rest of the tests into a variable, and add -m64 to CFLAGS for
those tests, so that in a subsequent patch some tests can be made to
build 32-bit.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220627140239.2464900-3-mpe@ellerman.id.au
The PUSH/POP_BASIC_STACK helpers in basic_asm.h do not ensure that the
stack pointer is always 16-byte aligned, which is required per the ABI.
Fix the macros to do the alignment if the caller fails to.
Currently only one caller passes a non-aligned size, tm_signal_self(),
which hasn't been caught in testing, presumably because it's a leaf
function.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220627140239.2464900-1-mpe@ellerman.id.au
The commit 208003254c32 ("selftests/kprobe: Do not test for GRP/
without event failures") removed a syntax which is no more cause
a syntax error (NO_EVENT_NAME error with GRP/).
However, there are another case (NO_EVENT_NAME error without GRP/)
which causes a same error. This adds a test for that case.
Link: https://lkml.kernel.org/r/165812790993.1377963.9762767354560397298.stgit@devnote2
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
A new feature is added where kprobes (and other probes) do not need to
explicitly state the event name when creating a probe. The event name will
come from what is being attached.
That is:
# echo 'p:foo/ vfs_read' > kprobe_events
Will no longer error, but instead create an event:
# cat kprobe_events
p:foo/p_vfs_read_0 vfs_read
This should not be tested as an error case anymore. Remove it from the
selftest as now this feature "breaks" the selftest as it no longer fails
as expected.
Link: https://lore.kernel.org/all/1656296348-16111-1-git-send-email-quic_linyyuan@quicinc.com/
Link: https://lkml.kernel.org/r/20220712161707.6dc08a14@gandalf.local.home
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Pull kvm fixes from Paolo Bonzini:
- Check for invalid flags to KVM_CAP_X86_USER_SPACE_MSR
- Fix use of sched_setaffinity in selftests
- Sync kernel headers to tools
- Fix KVM_STATS_UNIT_MAX
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Protect the unused bits in MSR exiting flags
tools headers UAPI: Sync linux/kvm.h with the kernel sources
KVM: selftests: Fix target thread to be migrated in rseq_test
KVM: stats: Fix value for KVM_STATS_UNIT_MAX for boolean stats
Daniel Borkmann says:
====================
bpf-next 2022-07-22
We've added 73 non-merge commits during the last 12 day(s) which contain
a total of 88 files changed, 3458 insertions(+), 860 deletions(-).
The main changes are:
1) Implement BPF trampoline for arm64 JIT, from Xu Kuohai.
2) Add ksyscall/kretsyscall section support to libbpf to simplify tracing kernel
syscalls through kprobe mechanism, from Andrii Nakryiko.
3) Allow for livepatch (KLP) and BPF trampolines to attach to the same kernel
function, from Song Liu & Jiri Olsa.
4) Add new kfunc infrastructure for netfilter's CT e.g. to insert and change
entries, from Kumar Kartikeya Dwivedi & Lorenzo Bianconi.
5) Add a ksym BPF iterator to allow for more flexible and efficient interactions
with kernel symbols, from Alan Maguire.
6) Bug fixes in libbpf e.g. for uprobe binary path resolution, from Dan Carpenter.
7) Fix BPF subprog function names in stack traces, from Alexei Starovoitov.
8) libbpf support for writing custom perf event readers, from Jon Doron.
9) Switch to use SPDX tag for BPF helper man page, from Alejandro Colomar.
10) Fix xsk send-only sockets when in busy poll mode, from Maciej Fijalkowski.
11) Reparent BPF maps and their charging on memcg offlining, from Roman Gushchin.
12) Multiple follow-up fixes around BPF lsm cgroup infra, from Stanislav Fomichev.
13) Use bootstrap version of bpftool where possible to speed up builds, from Pu Lehui.
14) Cleanup BPF verifier's check_func_arg() handling, from Joanne Koong.
15) Make non-prealloced BPF map allocations low priority to play better with
memcg limits, from Yafang Shao.
16) Fix BPF test runner to reject zero-length data for skbs, from Zhengchao Shao.
17) Various smaller cleanups and improvements all over the place.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (73 commits)
bpf: Simplify bpf_prog_pack_[size|mask]
bpf: Support bpf_trampoline on functions with IPMODIFY (e.g. livepatch)
bpf, x64: Allow to use caller address from stack
ftrace: Allow IPMODIFY and DIRECT ops on the same function
ftrace: Add modify_ftrace_direct_multi_nolock
bpf/selftests: Fix couldn't retrieve pinned program in xdp veth test
bpf: Fix build error in case of !CONFIG_DEBUG_INFO_BTF
selftests/bpf: Fix test_verifier failed test in unprivileged mode
selftests/bpf: Add negative tests for new nf_conntrack kfuncs
selftests/bpf: Add tests for new nf_conntrack kfuncs
selftests/bpf: Add verifier tests for trusted kfunc args
net: netfilter: Add kfuncs to set and change CT status
net: netfilter: Add kfuncs to set and change CT timeout
net: netfilter: Add kfuncs to allocate and insert CT
net: netfilter: Deduplicate code in bpf_{xdp,skb}_ct_lookup
bpf: Add documentation for kfuncs
bpf: Add support for forcing kfunc args to be trusted
bpf: Switch to new kfunc flags infrastructure
tools/resolve_btfids: Add support for 8-byte BTF sets
bpf: Introduce 8-byte BTF set
...
====================
Link: https://lore.kernel.org/r/20220722221218.29943-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before change:
selftests: bpf: test_xdp_veth.sh
Couldn't retrieve pinned program '/sys/fs/bpf/test_xdp_veth/progs/redirect_map_0': No such file or directory
selftests: xdp_veth [SKIP]
ok 20 selftests: bpf: test_xdp_veth.sh # SKIP
After change:
PING 10.1.1.33 (10.1.1.33) 56(84) bytes of data.
64 bytes from 10.1.1.33: icmp_seq=1 ttl=64 time=0.320 ms
--- 10.1.1.33 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.320/0.320/0.320/0.000 ms
selftests: xdp_veth [PASS]
For the test case, the following can be found:
ls /sys/fs/bpf/test_xdp_veth/progs/redirect_map_0
ls: cannot access '/sys/fs/bpf/test_xdp_veth/progs/redirect_map_0': No such file or directory
ls /sys/fs/bpf/test_xdp_veth/progs/
xdp_redirect_map_0 xdp_redirect_map_1 xdp_redirect_map_2
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jie2x Zhou <jie2x.zhou@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220719082430.9916-1-jie2x.zhou@intel.com
Ping sockets don't appear to make any attempt to preserve flow labels
created and set by userspace using IPV6_FLOWINFO_SEND. Instead they are
clobbered by autolabels (if enabled) or zero.
Grab the flowlabel out of the msghdr similar to how rawv6_sendmsg does
it and move the memset up so it doesn't get zeroed after.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
