Currently, driver sets the same grace period for fw fatal health reporter
to any type of function.
Since the lower level functions are more vulnerable to fw fatal errors as a
result of parent function closure/reload, set a smaller grace period for
the lower level functions, as follows:
1. For ECPF: 180 seconds.
2. For PF: 60 seconds.
3. For VF/SF: 30 seconds.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Start health poll at earlier stage, so if fw fatal issue occurred before
or during initialization commands such as init_hca or set_hca_cap the
poll health can detect and indicate that the driver is already in error
state.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the rx_oversize_pkts_buffer counter to ethtool statistics.
This counter exposes the number of dropped received packets due to
length which arrived to RQ and exceed software buffer size allocated by
the device for incoming traffic. It might imply that the device MTU is
larger than the software buffers size.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When XSK frame size is 3072 (or another power of two multiplied by 3),
KLM mechanism for NIC virtual memory page mapping can be optimized by
replacing it with KSM.
Before this change, two KLM entries were needed to map an XSK frame that
is not a power of two: one entry maps the UMEM memory up to the frame
length, the other maps the rest of the stride to the garbage page.
When the frame length divided by 3 is a power of two, it can be mapped
using 3 KSM entries, and the fourth will map the rest of the stride to
the garbage page. All 4 KSM entries are of the same size, which allows
for a much faster lookup.
Frame size 3072 is useful in certain use cases, because it allows
packing 4 frames into 3 pages. Generally speaking, other frame sizes
equal to PAGE_SIZE minus a power of two can be optimized in a similar
way, but it will require many more KSMs per frame, which slows down UMRs
a little bit, but more importantly may hit the limit for the maximum
number of KSM entries.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On striding RQ, when the XSK frame size doesn't match the MKey page
size, KLM is used for memory mappings, which is a slower mechanism than
MTT or KSM. It may happen in two cases:
1. Frame size is not a power of two (only possible in the unaligned mode
of XSK).
2. Frame size is 2048 bytes, and the firmware doesn't support MKey pages
smaller than 4096 bytes.
Depending on the case, print a warning and recommend to disable striding
RQ or upgrade the firmware.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
XSK RQs support striding RQ linear mode, but the stride size may be
bigger than the XSK frame size, because:
1. The stride size must be a power of two.
2. The stride size must be equal to the UMR page size. Each XSK frame is
treated as a separate page, because they aren't necessarily adjacent in
physical memory, so the driver can't put more than one stride per page.
3. The minimal MTT page size is 4096 on older firmware.
That means that if XSK frame size is 2048 or not a power of two, the
strides may be bigger than XSK frames. Normally, it's not a problem if
the hardware enforces the MTU. However, traffic between vports skips the
hardware MTU check, and oversized packets may be received.
If an oversized packet is bigger than the XSK frame but not bigger than
the stride, it will cause overwriting of the adjacent UMEM region. If
the packet takes more than one stride, they can be recycled for reuse,
so it's not a problem when the XSK frame size matches the stride size.
Work around the above issue by leveraging KLM to make a more
fine-grained mapping. The beginning of each stride is mapped to the
frame memory, and the padding up to the closest power of two is mapped
to the overflow page that doesn't belong to UMEM. This way, application
data corruption won't happen upon receiving packets bigger than MTU.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make mlx5e_mpwrq_mtts_per_wqe take into account that KSM requires
smaller alignment than MTT.
Ensure that there is always an even amount of MTTs in a UMR WQE, so that
complete octwords are formed, and no garbage is mapped.
Drop extra alignment in MLX5_MTT_OCTW that may cause setting too big
ucseg->xlt_octowords, also leading to mapping garbage.
Generalize some calculations by introducing the MLX5_OCTWORD constant.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of passing the unaligned flag, pass an enum that indicates the
UMR mode. The next commit will add the third mode (KLM for certain
configurations of XSK), which will be added to this enum instead of
adding another bool flag everywhere.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
XSK need_wakeup mechanism allows the driver to stop busy waiting for
buffers when the fill ring is empty, yield to the application and signal
it that the driver needs to be waken up after the application refills
the fill ring.
Add protection against the race condition on the RX (refill) side: if
the application refills buffers after xskrq->post_wqes is called, but
before mlx5e_xsk_update_rx_wakeup, NAPI will exit, skipping taking these
buffers to the hardware WQ, and the application won't wake it up again.
Optimize the whole need_wakeup logic, removing unneeded flows, to
compensate for this new check.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
XSK is a performance-critical data path. To avoid an indirect function
call with a retpoline, include XSK callbacks in the INDIRECT_CALL macro,
so that they are called directly in XSK flows.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_rxq_info_reg should get the actual napi_id, not 0, in order to
support socket busy polling properly.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The regular RQ remains open after opening an XSK socket, in order to
guarantee that closing the XSK socket never fails due to an error when
reopening the regular RQ.
To save memory, the regular RQ can be deactivated and flushed, releasing
all pages, when an XSK socket is open.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When mvpp2 is unloaded, the driver specific debugfs directory is not
removed, which technically leads to a memory leak. However, this
directory is only created when the first device is probed, so the
hardware is present. Removing the module is only something a developer
would to when e.g. testing out changes, so the module would be
reloaded. So this memory leak is minor.
The original attempt in commit fe2c9c61f6 ("net: mvpp2: debugfs: fix
memory leak when using debugfs_lookup()") that was labelled as a memory
leak fix was not, it fixed a refcount leak, but in doing so created a
problem when the module is reloaded - the directory already exists, but
mvpp2_root is NULL, so we lose all debugfs entries. This fix has been
reverted.
This is the alternative fix, where we remove the offending directory
whenever the driver is unloaded.
Fixes: 21da57a231 ("net: mvpp2: add a debugfs interface for the Header Parser")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/E1ofOAB-00CzkG-UO@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch just updates comments throughout the IPA code.
Transaction state is now tracked using indexes into an array rather
than linked lists, and a few comments refer to the "old way" of
doing things. The description of how transactions are used was
changed to refer to "operations" rather than "commands", to
(hopefully) remove a possible ambiguity.
IPA register offsets and fields are now handled differently as well,
and the register documentation is updated to better describe the
code.
A few minor updates to comments were made (e.g., adding a missing
word, fixing a typo or punctuation, etc.).
Finally, the local macro atomic_dec_not_zero() is no longer used, so
it is deleted.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220930224527.3503404-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull thermal control updates from Rafael Wysocki:
"The most significant part of this update is the thermal control DT
initialization rework from Daniel Lezcano and the following conversion
of drivers to use the new API introduced by it
Apart from that, the maximum number of trip points in a thermal zone
is increased and there are some fixes and code cleanups
Specifics:
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when KASAN is enabled as it detects use after free
when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already shown in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar)
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang)
- Use module_pci_driver() macro in the int340x processor_thermal
driver (Shang XiaoJing)
- Use get_cpu() instead of smp_processor_id() in the intel_powerclamp
thermal driver to prevent it from crashing and remove unused
accounting for IRQ wakes from it (Srinivas Pandruvada)
- Consolidate priv->data_vault checks in int340x_thermal (Rafael
Wysocki)
- Check the policy first in cpufreq_cooling_register() (Xuewen Yan)
- Drop redundant error message from da9062-thermal (zhaoxiao)
- Drop of_match_ptr() from thermal_mmio (Jean Delvare)"
* tag 'thermal-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: core: Increase maximum number of trip points
thermal: int340x: processor_thermal: Use module_pci_driver() macro
thermal: intel_powerclamp: Remove accounting for IRQ wakes
thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to avoid crash
thermal: int340x_thermal: Consolidate priv->data_vault checks
thermal: cpufreq_cooling: Check the policy first in cpufreq_cooling_register()
thermal: Drop duplicate words from comments
thermal: move from strlcpy() with unused retval to strscpy()
thermal: da9062-thermal: Drop redundant error message
thermal/drivers/thermal_mmio: Drop of_match_ptr()
thermal: gov_user_space: Do not lock thermal zone mutex
Revert "mlxsw: core: Add the hottest thermal zone detection"
thermal/core: Fix lockdep_assert() warning
thermal/core: Move the mutex inside the thermal_zone_device_update() function
thermal/core: Move the thermal zone lock out of the governors
thermal/governors: Group the thermal zone lock inside the throttle function
thermal/core: Rework the monitoring a bit
thermal/core: Rearm the monitoring only one time
thermal/drivers/qcom/spmi-adc-tm5: Remove unnecessary print function dev_err()
thermal/of: Remove old OF code
...
Merge core thermal control changes for 6.1-rc1:
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar).
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang).
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki)
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when KASAN is enabled as it detects use after
free when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already showed in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)
* thermal-core: (47 commits)
thermal: core: Increase maximum number of trip points
thermal: move from strlcpy() with unused retval to strscpy()
thermal: gov_user_space: Do not lock thermal zone mutex
Revert "mlxsw: core: Add the hottest thermal zone detection"
thermal/core: Fix lockdep_assert() warning
thermal/core: Move the mutex inside the thermal_zone_device_update() function
thermal/core: Move the thermal zone lock out of the governors
thermal/governors: Group the thermal zone lock inside the throttle function
thermal/core: Rework the monitoring a bit
thermal/core: Rearm the monitoring only one time
thermal/drivers/qcom/spmi-adc-tm5: Remove unnecessary print function dev_err()
thermal/of: Remove old OF code
thermal/core: Move set_trip_temp ops to the sysfs code
thermal/drivers/samsung: Switch to new of thermal API
regulator/drivers/max8976: Switch to new of thermal API
Input: sun4i-ts - switch to new of thermal API
iio/drivers/sun4i_gpadc: Switch to new of thermal API
hwmon/drivers/core: Switch to new of thermal API
hwmon: pm_bus: core: Switch to new of thermal API
ata/drivers/ahci_imx: Switch to new of thermal API
...
wwan_register_ops calls wwan_create_default_link, which ends up in the
ipc_wwan_newlink callback that locks ipc_wwan->if_mutex. However, this
mutex is not yet initialized by that point. Fix it by moving mutex_init
above the wwan_register_ops call. This also makes the order of
operations in ipc_wwan_init symmetric to ipc_wwan_deinit.
Fixes: 83068395bb ("net: iosm: create default link via WWAN core")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the macsec offload feature to cn10k
PF netdev driver. The macsec offload ops like adding, deleting
and updating SecYs, SCs, SAs and stats are supported. XPN support
will be added in later patches. Some stats use same counter in hardware
which means based on the SecY mode the same counter represents different
stat. Hence when SecY mode/policy is changed then snapshot of current
stats are captured. Also there is no provision to specify the unique
flow-id/SCI per packet to hardware hence different mac address needs to
be set for macsec interfaces.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds debugfs entry to dump MCS secy, sc,
sa, flowid and port stats. This helps in debugging
the packet path and to figure out where exactly packet
was dropped.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware triggers an interrupt for events like PN wrap to zero,
PN crosses set threshold. This interrupt is received
by the MCS_AF. MCS AF then finds the PF/VF to which SA is mapped
and notifies them using mcs_intr_notify mbox message.
PF/VF using mcs_intr_cfg mbox can configure the list
of interrupts for which they want to receive the
notification from AF.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mailbox messages to return the resource stats to the
caller. Stats of SecY, SC and SAs as per the macsec standard,
TCAM flow id hits/miss, mailbox to clear the stats are
implemented.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Ankur Dwivedi <adwivedi@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Out of all the TCAM entries, reserve last TX and RX TCAM flow
entry(low priority) so that normal traffic can be sent out and
received. The traffic which needs macsec processing hits the
high priority TCAM flows. Also install a FLR handler to free
the allocated resources for PF/VF.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To establish a macsec connection association netdev driver
needs hardware resources like SecY, TCAM flows, SCs and SAs.
This patch manages allocating, freeing and configuring those
resources. AF consumers can request resources and configure them
via these mailbox messages. AF can allocate until it runs out of
hardware resources.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are set of configurations to be done at MCS port level like
bringing port out of reset, making port as operational or bypass.
This patch adds all the port related mailbox message handlers
so that AF consumers can use them.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K-B and CNF10K-B has macsec block(MCS) to encrypt and
decrypt packets at MAC level. This block is a global resource
with hardware resources like SecYs, SCs and SAs and is in
between NIX block and RPM LMAC. CN10K-B silicon has only one MCS
block which receives packets from all LMACS whereas CNF10K-B has
seven MCS blocks for seven LMACs. Both MCS blocks are
similar in operation except for few register offsets and some
configurations require writing to different registers. Those
differences between IPs are handled using separate ops.
This patch adds basic driver and does the initial hardware
calibration and parser configuration.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This frees "mac" and tries to display its address as part of the error
message on the next line. Swap the order.
Fixes: fd3040b939 ("net: ethernet: Add driver for Sunplus SP7021")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for port mirroring. It is possible to mirror only one port
at a time and it is possible to have both ingress and egress mirroring.
Frames injected by the CPU don't get egress mirrored because they are
bypassing the analyzer module.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for port police. It is possible to police only on the
ingress side. To be able to add police support also it was required to
add tc-matchall classifier offload support.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_tpa_stop() allocates a memory chunk from new_data with
bnx2x_frag_alloc(). The new_data should be freed when gets some error.
But when "pad + len > fp->rx_buf_size" is true, bnx2x_tpa_stop() returns
without releasing the new_data, which will lead to a memory leak.
We should free the new_data with bnx2x_frag_free() when "pad + len >
fp->rx_buf_size" is true.
Fixes: 07b0f00964 ("bnx2x: fix possible panic under memory stress")
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PTP_PF_EXTTS support for non-PCI11x1x devices since they do not support
the PTP-IO Input event triggered timestamping mechanisms added
Fixes: 60942c397a ("net: lan743x: Add support for PTP-IO Event Input External Timestamp (extts)")
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the kemdup could return NULL, it should be better to check the return
value and return error if fails.
Moreover, the return value of prestera_acl_ruleset_keymask_set() should
be checked by cascade.
Fixes: 604ba23090 ("net: prestera: flower template support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Taras Chornyi<tchornyi@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for multigig copper SFP modules from RollBall/Hilink.
These modules have a specific way to access clause 45 registers of the
internal PHY.
We also need to wait at least 22 seconds after deasserting TX disable
before accessing the PHY. The code waits for 25 seconds just to be sure.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some multigig SFPs from RollBall and Hilink do not expose functional
MDIO access to the internal PHY of the SFP via I2C address 0x56
(although there seems to be read-only clause 22 access on this address).
Instead these SFPs PHY can be accessed via I2C via the SFP Enhanced
Digital Diagnostic Interface - I2C address 0x51. The SFP_PAGE has to be
selected to 3 and the password must be filled with 0xff bytes for this
PHY communication to work.
This extends the mdio-i2c driver to support this protocol by adding a
special parameter to mdio_i2c_alloc function via which this RollBall
protocol can be selected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of configuring the I2C mdiobus when SFP driver is probed,
create/destroy the mdiobus before the PHY is probed for/after it is
released.
This way we can tell the mdio-i2c code which protocol to use for each
SFP transceiver.
Move the code that determines MDIO I2C protocol from
sfp_sm_probe_for_phy() to sfp_sm_mod_probe(), where most of the SFP ID
parsing is done. Don't allocate I2C bus if no PHY is expected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macros SFP_QUIRK(), SFP_QUIRK_M() and SFP_QUIRK_F() for defining SFP
quirk table entries. Use them to deduplicate the code a little bit.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFPs may contain an internal PHY which may in some cases want to
connect with the host interface in 1000base-x/2500base-x mode.
Do not fail if such PHY is being attached in one of these PHY interface
modes.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Select the host interface configuration according to the capabilities of
the host if the host provided them. This is currently provided only when
connecting PHY that is inside a SFP.
The PHY supports several configurations of host communication:
- always communicate with host in 10gbase-r, even if copper speed is
lower (rate matching mode),
- the same as above but use xaui/rxaui instead of 10gbase-r,
- switch host SerDes mode between 10gbase-r, 5gbase-r, 2500base-x and
sgmii according to copper speed,
- the same as above but use xaui/rxaui instead of 10gbase-r.
This mode of host communication, called MACTYPE, is by default selected
by strapping pins, but it can be changed in software.
This adds support for selecting this mode according to which modes are
supported by the host.
This allows the kernel to:
- support SFP modules with 88X33X0 or 88E21X0 inside them
Note: we use mv3310_select_mactype() for both 88X3310 and 88X3340,
although 88X3340 does not support XAUI. This is not a problem because
88X3340 does not declare XAUI in it's supported_interfaces, and so this
function will never choose that MACTYPE.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[ rebase, updated, also added support for 88E21X0 ]
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some register definitions were defined with spaces used for indentation.
Change them to tabs.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the supported PHY interface types to phylib if the PHY we are
connecting is inside a SFP, so that the PHY driver can select an
appropriate host configuration mode for their interface according to
the host capabilities.
For example the Marvell 88X3310 PHY inside RollBall SFP modules
defaults to 10gbase-r mode on host's side, and the marvell10g
driver currently does not change this setting. But a host may not
support 10gbase-r. For example Turris Omnia only supports sgmii,
1000base-x and 2500base-x modes. The PHY can be configured to use
those modes, but in order for the PHY driver to do that, it needs
to know which modes are supported.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_sfp_config() now only deals with configuring the MAC for a
SFP containing a PHY. Rename it to be specific.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where a MAC provides a phy_interface_t bitmap, use these bitmaps to
select the operating interface mode for optical SFP modules, rather
than using the linkmode bitmaps.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently parse the SFP EEPROM to a bitmap of ethtool link modes,
and then attempt to convert the link modes to a PHY interface mode.
While this works at present, there are cases where this is sub-optimal.
For example, where a module can operate with several different PHY
interface modes.
To start addressing this, arrange for the SFP EEPROM parsing to also
provide a bitmap of the possible PHY interface modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than having the ability to validate all supported interface
modes or a single interface mode, introduce the ability to validate
a subset of supported modes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[ rebased on current net-next ]
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_start_xmit field in net_device_ops is expected to be of type
netdev_tx_t (*ndo_start_xmit)(struct sk_buff *skb, struct net_device *dev).
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of sparx5_port_xmit_impl should be changed from int to
netdev_tx_t.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1703
Cc: llvm@lists.linux.dev
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the initial implementation of XSK in mlx5e, XSK RQs coexisted with
regular RQs in the same channel. The main idea was to allow RSS work the
same for regular traffic, without need to reconfigure RSS to exclude XSK
queues.
However, this scheme didn't prove to be beneficial, mainly because of
incompatibility with other vendors. Some tools don't properly support
using higher indices for XSK queues, some tools get confused with the
double amount of RQs exposed in sysfs. Some use cases are purely XSK,
and allocating the same amount of unused regular RQs is a waste of
resources.
This commit changes the queuing scheme to the standard one, where XSK
RQs replace regular RQs on the channels where XSK sockets are open. Two
RQs still exist in the channel to allow failsafe disable of XSK, but
only one is exposed at a time. The next commit will achieve the desired
memory save by flushing the buffers when the regular RQ is unused.
As the result of this transition:
1. It's possible to use RSS contexts over XSK RQs.
2. It's possible to dedicate all queues to XSK.
3. When XSK RQs coexist with regular RQs, the admin should make sure no
unwanted traffic goes into XSK RQs by either excluding them from RSS or
settings up the XDP program to return XDP_PASS for non-XSK traffic.
4. When using a mixed fleet of mlx5e devices and other netdevs, the same
configuration can be applied. If the application supports the fallback
to copy mode on unsupported drivers, it will work too.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
