Checking the relevant rxd bits for the checksum information only indicates
if the checksum verification was performed by the hardware and doesn't show
actual checksum errors. Checksum errors are indicated in the info field of
the DMA descriptor. Fix packets erroneously marked as CHECKSUM_UNNECESSARY
by checking the extra bits as well.
Those bits are only passed to the driver for MMIO devices at the moment, so
limit checksum offload to those.
Fixes: 2122dfbfd0 ("mt76: mt7615: add rx checksum offload support")
Fixes: 94244d2ea5 ("mt76: mt7915: add rx checksum offload support")
Fixes: 0e75732764 ("mt76: mt7921: enable rx csum offload")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005130824.23371-2-nbd@nbd.name
When 802.3 decap offload is enabled, the hardware indicates header translation
failure, whenever either the LLC-SNAP header was not found, or a VLAN header
with an unregcognized tag is present.
In that case, the hardware inserts a 2-byte length fields after the MAC
addresses. For VLAN packets, this tag needs to be removed. However,
for 802.3 LLC packets, the length bytes should be preserved, since there
is no separate ethertype field in the data.
This fixes an issue where the length field was omitted for LLC frames, causing
them to be malformed after hardware decap.
Fixes: 1eeff0b4c1 ("mt76: mt7915: fix decap offload corner case with 4-addr VLAN frames")
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005130824.23371-1-nbd@nbd.name
Kalle Valo says:
====================
wireless-next patches for v6.1
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
- refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
- support CYW43439 SDIO chipset
- support BCM4378 on Apple platforms
- support CYW89459 PCIe chipset
rtw89
- more work to get rtw8852c supported
- P2P support
- support for enabling and disabling MSDU aggregation via nl80211
mt76
- tx status reporting improvements
ath11k
- cold boot calibration support on WCN6750
- Target Wake Time (TWT) debugfs support for STA interface
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- implement SRAM dump debugfs interface
- enable threaded NAPI on all hardware
- WoW support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
wcn36xx
- add SNR from a received frame as a source of system entropy
* tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (231 commits)
wifi: rtl8xxxu: Improve rtl8xxxu_queue_select
wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
wifi: rtl8xxxu: gen2: Enable 40 MHz channel width
wifi: rtw89: 8852b: configure DLE mem
wifi: rtw89: check DLE FIFO size with reserved size
wifi: rtw89: mac: correct register of report IMR
wifi: rtw89: pci: set power cut closed for 8852be
wifi: rtw89: pci: add to do PCI auto calibration
wifi: rtw89: 8852b: implement chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add DMA busy checking bits to chip info
wifi: rtw89: mac: define DMA channel mask to avoid unsupported channels
wifi: rtw89: pci: mask out unsupported TX channels
iwlegacy: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper
ipw2x00: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
wifi: iwlwifi: Track scan_cmd allocation size explicitly
brcmfmac: Remove the call to "dtim_assoc" IOVAR
brcmfmac: increase dcmd maximum buffer size
brcmfmac: Support 89459 pcie
brcmfmac: increase default max WOWL patterns to 16
cw1200: fix incorrect check to determine if no element is found in list
...
====================
Link: https://lore.kernel.org/r/20220930150413.A7984C433D6@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to
handle the .suspend/.resume callbacks. The new macros allow suspend
and resume functions to be automatically dropped without any #ifdef
guards.
Tested-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to
handle the .suspend/.resume callbacks. The new macros allow suspend
and resume functions to be automatically dropped without any #ifdef
guards.
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In case of PCIe interoperability problem shows up, the firmware
payload may be corrupted in download stage. Turn off L0s to keep
fw download process accurately.
[ 1093.528363] mt7921e 0000:3b:00.0: Message 00000007 (seq 7) timeout
[ 1093.528414] mt7921e 0000:3b:00.0: Failed to start patch
[ 1096.600156] mt7921e 0000:3b:00.0: Message 00000010 (seq 8) timeout
[ 1096.600207] mt7921e 0000:3b:00.0: Failed to release patch semaphore
[ 1097.699031] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1098.758427] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1099.834408] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1100.915264] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1101.990625] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1103.077587] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1104.173258] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1105.248466] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1106.336969] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1106.397542] mt7921e 0000:3b:00.0: hardware init failed
Cc: stable@vger.kernel.org
Fixes: bf3747ae2e ("mt76: mt7921: enable aspm by default")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Country Location Control (CLC) is an additional control for country rules
in firmware. We introduce this new feature to make sure mt7921 series
working properly in all region.
The addtional policies would be put into firmware based on differnt
regions. mt76 driver should be in charge of submitting per region policy.
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: YN Chen <YN.Chen@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We should reset mstat->airtime_ac along with clear up the entries in the
hardware WLAN table for the Rx and Rx accumulative airtime. Otherwsie, the
value msta->airtime_ac - [tx, rx]_last may be a negative and that is not
the actual airtime the device took in the last run.
Reported-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not need to check running state before configuring implicit Tx
beamform. It is okay to configure implicit Tx beamform in run time.
Noted that the existing connected stations will be applied for new
configuration only if they reconnected to the interface.
Fixes: 6d6dc980e0 ("mt76: mt7915: add implicit Tx beamforming support")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize msta pointer to NULL in mt7921_mac_fill_rx() in order to not
dereference a uninitialized pointer.
Fixes: 0880d40871 ("mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the error that mcs will be reduced to a range of 0 to 7 in ht mode.
Fixes: 70fd1333cd ("mt76: mt7915: rework .set_bitrate_mask() to support more options")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
False positive reset would be possibly triggered by those commands we
applied in suspend with HZ MCU timeout, especially it happened when we
enabled kernel log in pm core to diagnose how much time we spend in each
driver during suspend procedure. So we enlarge the value and align the MCU
timeout as other commands we did to reduce the false positive reset.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Given that there's no data coming from network stack for binding flows,
hence driver counts and reports station's statistics directly through
NL80211_STA_INFO_* based on active PPDU based TxS for offloading data.
Apart from that, WA firmware and its offloading engine (SDO) have hardcoded
"2" as PID, so we introduce MT_PACKET_ID_WED to differentiate WED reporting.
Note that PPDU format TxS is mutually exclusive with MT_TXD5_TX_STATUS_HOST.
Co-developed-by: Yi-Chia Hsieh <yi-chia.hsieh@mediatek.com>
Signed-off-by: Yi-Chia Hsieh <yi-chia.hsieh@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the regression of the firmware version report since
'b9ec27102ac0 ('mt76: connac: move mt76_connac2_load_ram in connac
module')'.
Fixes: b9ec27102a ("mt76: connac: move mt76_connac2_load_ram in connac module")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7921_mutex_acquire at mt7921_[start, stop]_ap to fix the race
with the context holding dev->muxtex and the driver might access the
device in low power state.
Fixes: 24299fc869 ("mt76: mt7921: enable rx header traslation offload")
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7921_mutex_acquire at mt7921_[start, stop]_ap to fix the race
with the context holding dev->muxtex and the driver might access the
device in low power state.
Fixes: 9d958b60eb ("mt76: mt7921: fix command timeout in AP stop period")
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Simplify mt76x02u_multiple_mcu_reads routine since burst is always
false.
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce rx_check callback support for mt7663s driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix possible unaligned pointer in mt76_connac_mcu_add_nested_tlv
routine.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 25702d9c55 ("mt76: connac: rely on le16_add_cpu in mt76_connac_mcu_add_nested_tlv")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7921 driver, introduce mt7615_mutex_acquire/release in
mt7615_sta_set_decap_offload in order to avoid sending mcu commands
while the device is in low-power state.
Fixes: d4b98c63d7 ("mt76: mt7615: add support for rx decapsulation offload")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix transmitting packets hangs with continuing to pull the pending packet
from mac80211 queues when receiving Tx status notification from the device.
Fixes: aac5104bf6 ("mt76: sdio: do not run mt76_txq_schedule directly")
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This if statement is never true. It was supposed to have been deleted
as part of commit 454b768f9b ("mt76: mt7921: Let PCI core handle
power state and use pm_sleep_ptr()") but was missed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't dereference "sar_root" after it has been freed.
Fixes: f965333e49 ("mt76: mt7921: introduce ACPI SAR support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Smatch complains that:
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:428 mt7915_mac_fill_rx()
error: uninitialized symbol 'msta'.
It looks like this was supposed to be initialized to NULL.
Fixes: 0880d40871 ("mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is not meaningful to poll sta stat when there is no data traffic.
So polling sta stat when the device has transmitted data instead to save
CPU power.
That implies that it is unallowed the stat_work to work while MCU is being
initialized in the really early stage to fix the possible time to time MCU
initialization failure.
Fixes: d39b52e31a ("mt76: introduce mt76_sdio module")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Because wake_work and sdio->stat_work share the same workqueue mt76->wq,
if sdio->stat_work cannot acquire the mutex lock such as that was possibly
held up by [mt7615, mt7921]_mutex_acquire. Additionally, if
[mt7615, mt7921]_mutex_acquire was called by sdio->stat_work self, the wake
would be blocked by itself. Thus, we move the stat_work into
ieee80211_workqueue instead to break the deadlock.
Fixes: d39b52e31a ("mt76: introduce mt76_sdio module")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since both mt7921_rx_check and mt7921_queue_rx_skb routines are used by
all chipsets (mmio, usb and sdio), move them in mac.c and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
remove unnecessary MT76_STATE_SUSPEND manipulation to be consistent
with the mt7921[e, s] driver.
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is unexpected that the reset work is running simultaneously with
the suspend or resume context and it is possible that reset work is still
running even after mt7921 is suspended if we don't fix the race issue.
Thus, the suspend procedure should be waiting until the reset is completed
at the beginning and ignore the subsequent the reset requests.
In case there is an error that happens during either suspend or resume
handler, we will schedule a reset task to recover the error before
returning the error code to ensure we can immediately fix the error there.
Fixes: df3e4143ba ("mt76: mt7921u: add suspend/resume support")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is unexpected that the reset work is running simultaneously with
the suspend or resume context and it is possible that reset work is still
running even after mt7921 is suspended if we don't fix the race issue.
Thus, the suspend procedure should be waiting until the reset is completed
at the beginning and ignore the subsequent the reset requests.
In case there is an error that happens during either suspend or resume
handler, we will schedule a reset task to recover the error before
returning the error code to ensure we can immediately fix the error there.
Fixes: ca74b9b907 ("mt76: mt7921s: add reset support")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is unexpected that the reset work is running simultaneously with
the suspend or resume context and it is possible that reset work is still
running even after mt7921 is suspended if we don't fix the race issue.
Thus, the suspend procedure should be waiting until the reset is completed
at the beginning and ignore the subsequent the reset requests.
In case there is an error that happens during either suspend or resume
handler, we will schedule a reset task to recover the error before
returning the error code to ensure we can immediately fix the error there.
Fixes: 0c1ce98846 ("mt76: mt7921: add wifi reset support")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce rx_check callback support for mt7663u and mt7921u drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Compared to fixed payload packets, random payload packets have better
measured EVM under the same txpower. Our tests show EVM becomes at least
2-3 dB better in test cases with high rate and long tx length, which also
aligns the testing results to proprietary driver.
Suggested-by: Jm Chen <jm.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_connac_reg_map structure in mt76-connac module since it
is used by all connac2 chipset. Align structure definitions.
This is a preliminary patch to add mt7990 chipset support.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The A-MSDU data needs to be stored per-link and aggregated into a single
value for the station. Add a new struct ieee_80211_sta_aggregates in
order to store this data and a new function
ieee80211_sta_recalc_aggregates to update the current data for the STA.
Note that in the non MLO case the pointer in ieee80211_sta will directly
reference the data in deflink.agg, which means that recalculation may be
skipped in that case.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The SMPS power save mode needs to be per-link rather than being shared
for all links. As such, move it into struct ieee80211_link_sta.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of drv own fail in reset, we may need to run mac_reset several
times. The sequence would trigger system crash as the log below.
Because we do not re-enable/schedule "tx_napi" before disable it again,
the process would keep waiting for state change in napi_diable(). To
avoid the problem and keep status synchronize for each run, goto final
resource handling if drv own failed.
[ 5857.353423] mt7921e 0000:3b:00.0: driver own failed
[ 5858.433427] mt7921e 0000:3b:00.0: Timeout for driver own
[ 5859.633430] mt7921e 0000:3b:00.0: driver own failed
[ 5859.633444] ------------[ cut here ]------------
[ 5859.633446] WARNING: CPU: 6 at kernel/kthread.c:659 kthread_park+0x11d
[ 5859.633717] Workqueue: mt76 mt7921_mac_reset_work [mt7921_common]
[ 5859.633728] RIP: 0010:kthread_park+0x11d/0x150
[ 5859.633736] RSP: 0018:ffff8881b676fc68 EFLAGS: 00010202
......
[ 5859.633766] Call Trace:
[ 5859.633768] <TASK>
[ 5859.633771] mt7921e_mac_reset+0x176/0x6f0 [mt7921e]
[ 5859.633778] mt7921_mac_reset_work+0x184/0x3a0 [mt7921_common]
[ 5859.633785] ? mt7921_mac_set_timing+0x520/0x520 [mt7921_common]
[ 5859.633794] ? __kasan_check_read+0x11/0x20
[ 5859.633802] process_one_work+0x7ee/0x1320
[ 5859.633810] worker_thread+0x53c/0x1240
[ 5859.633818] kthread+0x2b8/0x370
[ 5859.633824] ? process_one_work+0x1320/0x1320
[ 5859.633828] ? kthread_complete_and_exit+0x30/0x30
[ 5859.633834] ret_from_fork+0x1f/0x30
[ 5859.633842] </TASK>
Cc: stable@vger.kernel.org
Fixes: 0efaf31dec ("mt76: mt7921: fix MT7921E reset failure")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Link: https://lore.kernel.org/r/727eb5ffd3c7c805245e512da150ecf0a7154020.1659452909.git.deren.wu@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building with Clang we encounter this warning:
| drivers/net/wireless/mediatek/mt7601u/debugfs.c:92:6: error: format
| specifies type 'unsigned char' but the argument has type 'int'
| [-Werror,-Wformat] dev->ee->reg.start + dev->ee->reg.num - 1);
The format specifier used is `%hhu` which describes a u8. Both
`dev->ee->reg.start` and `.num` are u8 as well. However, the expression
as a whole is promoted to an int as you cannot get smaller-than-int from
addition. Therefore, to fix the warning, use the promoted-to-type's
format specifier -- in this case `%d`.
example:
```
uint8_t a = 4, b = 7;
int size = sizeof(a + b - 1);
printf("%d\n", size);
// output: 4
```
See more:
(https://wiki.sei.cmu.edu/confluence/display/c/INT02-C.+Understand+integer+conversion+rules)
"Integer types smaller than int are promoted when an operation is
performed on them. If all values of the original type can be represented
as an int, the value of the smaller type is converted to an int;
otherwise, it is converted to an unsigned int."
Signed-off-by: Justin Stitt <justinstitt@google.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220711212932.1501592-1-justinstitt@google.com
When building with Clang we encounter the following warning:
| drivers/net/wireless/mediatek/mt7601u/eeprom.c:193:5: error: format
| specifies type 'char' but the argument has type 'int' [-Werror,-Wformat]
| chan_bounds[idx].start + chan_bounds[idx].num - 1);
Variadic functions (printf-like) undergo default argument promotion.
Documentation/core-api/printk-formats.rst specifically recommends using
the promoted-to-type's format flag.
Moreover, C11 6.3.1.1 states:
(https://www.open-std.org/jtc1/sc22/wg14/www/docs/n1548.pdf) `If an int
can represent all values of the original type ..., the value is
converted to an int; otherwise, it is converted to an unsigned int.
These are called the integer promotions.`
With this information in hand, we really should stop using `%hh[dxu]` or
`%h[dxu]` as they usually prompt Clang -Wformat warnings as well as go
against documented standard recommendations.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220709001527.618593-1-justinstitt@google.com
mt76 patches for 5.20
- preparation for new chipset support
- fixes
- VHT/HE related improvements
- ACPI SAR support
[kvalo@kernel.org: fix mac80211 API changes in start_ap() and stop_ap()]
