mlx5e_alloc_xdpsq calculates sq->stop_room internally, but there is
already a function for that: mlx5e_stop_room_for_max_wqe. This commit
makes use of this function.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To shorten and simplify code, let mlx5e_get_sw_max_sq_mpw_wqebbs accept
mdev and derive max SQ WQEBBs from it. Also rename the function to a
more generic name mlx5e_get_max_sq_aligned_wqebbs, because the following
patches will use it in non-MPWQE contexts.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the driver can silently fall back to legacy RQ after enabling
XDP, even if striding RQ was active before. It happens when PAGE_SIZE is
bigger than the maximum supported stride size. This commit changes this
behavior to more straightforward: if an operation (enabling XDP) doesn't
support the current parameters (striding RQ mode), it fails.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlx5e_verify_rx_mpwqe_strides is only used in en/params.c, so it can be
made static and removed from en/params.h.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No need to keep max_sq_wqebbs in mlx5e_txqsq and mlx5e_xdpsq, as it's
only used when allocating the queues. Removing an extra field reduces
the struct size.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return value of mlx5e_get_max_sq_wqebbs is clamped down to
MLX5_SEND_WQE_MAX_WQEBBS = 16, which fits into u8. This commit changes
the return type of this function to u8 for stricter type safety.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
updates from mlx5-next 2022-09-24
Updates form mlx5-next including[1]:
1) HW definitions and support for NPPS clock settings.
2) various cleanups
3) Enable hash mode by default for all NICs
4) page tracker and advanced virtualization HW definitions for vfio
[1] https://lore.kernel.org/netdev/20220907233636.388475-1-saeed@kernel.org/
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Remove from FPGA IFC file not-needed definitions
net/mlx5: Remove unused structs
net/mlx5: Remove unused functions
net/mlx5: detect and enable bypass port select flow table
net/mlx5: Lag, enable hash mode by default for all NICs
net/mlx5: Lag, set active ports if support bypass port select flow table
RDMA/mlx5: Don't set tx affinity when lag is in hash mode
net/mlx5: add IFC bits for bypassing port select flow table
net/mlx5: Add support for NPPS with real time mode
net/mlx5: Expose NPPS related registers
net/mlx5: Query ADV_VIRTUALIZATION capabilities
net/mlx5: Introduce ifc bits for page tracker
RDMA/mlx5: Move function mlx5_core_query_ib_ppcnt() to mlx5_ib
====================
Link: https://lore.kernel.org/all/20220927201906.234015-1-saeed@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
ice: xsk: ZC changes
Maciej Fijalkowski says:
This set consists of two fixes to issues that were either pointed out on
indirectly (John was reviewing AF_XDP selftests that were testing ice's
ZC support) mailing list or were directly reported by customers.
First patch allows user space to see done descriptor in CQ even after a
single frame being transmitted and second patch removes the need for
having HW rings sized to power of 2 number of descriptors when used
against AF_XDP.
I also forgot to mention that due to the current Tx cleaning algorithm,
4k HW ring was broken and these two patches bring it back to life, so we
kill two birds with one stone.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: xsk: drop power of 2 ring size restriction for AF_XDP
ice: xsk: change batched Tx descriptor cleaning
====================
Link: https://lore.kernel.org/r/20220927164112.4011983-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the following set of commands fails:
$ ip link add br0 type bridge # vlan_filtering 0
$ ip link set swp0 master br0
$ bridge vlan
port vlan-id
swp0 1 PVID Egress Untagged
$ bridge vlan add dev swp0 vid 10
Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs.
Dumping ocelot->vlans, one can see that the 2 egress-untagged VLANs on swp0 are
vid 1 (the bridge PVID) and vid 4094, a PVID used privately by the driver for
VLAN-unaware bridging. So this is why bridge vid 10 is refused, despite
'bridge vlan' showing a single egress untagged VLAN.
As mentioned in the comment added, having this private VLAN does not impose
restrictions to the hardware configuration, yet it is a bookkeeping problem.
There are 2 possible solutions.
One is to make the functions that operate on VLAN-unaware pvids:
- ocelot_add_vlan_unaware_pvid()
- ocelot_del_vlan_unaware_pvid()
- ocelot_port_setup_dsa_8021q_cpu()
- ocelot_port_teardown_dsa_8021q_cpu()
call something different than ocelot_vlan_member_(add|del)(), the latter being
the real problem, because it allocates a struct ocelot_bridge_vlan *vlan which
it adds to ocelot->vlans. We don't really *need* the private VLANs in
ocelot->vlans, it's just that we have the extra convenience of having the
vlan->portmask cached in software (whereas without these structures, we'd have
to create a raw ocelot_vlant_rmw_mask() procedure which reads back the current
port mask from hardware).
The other solution is to filter out the private VLANs from
ocelot_port_num_untagged_vlans(), since they aren't what callers care about.
We only need to do this to the mentioned function and not to
ocelot_port_num_tagged_vlans(), because private VLANs are never egress-tagged.
Nothing else seems to be broken in either solution, but the first one requires
more rework which will conflict with the net-next change 36a0bf4435 ("net:
mscc: ocelot: set up tag_8021q CPU ports independent of user port affinity"),
and I'd like to avoid that. So go with the other one.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220927122042.1100231-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable support for adding TC rules that filter on the VLAN priority
in switchdev mode.
VLAN priority are the first 3 bits of 16b switch field vector word
which contain also vlan id value within its last 12 bits.
When getting vlan priority value from tc match.key it
has to be shifted first to proper bits positions (by VLAN_PRIO_SHIFT)
and then can be added to the joint 'vlan' field in ice_vlan_hdr
in lookup element.
The mask of lookup changes accordingly.
0x0FFF - when only vlan id is added in filter
0xE000 - when only vlan priority is added in filter
0xEFFF - when both these values are specified
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This is the absolute minimum viable TC implementation to get traffic to
VFs and allow them to be tested; it supports no match fields besides
ingress port, no actions besides mirred and drop, and no stats.
Example usage:
tc filter add dev $PF parent ffff: flower skip_sw \
action mirred egress mirror dev $VFREP
tc filter add dev $VFREP parent ffff: flower skip_sw \
action mirred egress redirect dev $PF
gives a VF unfiltered access to the network out the physical port ($PF
acts here as a physical port representor).
More matches, actions, and counters will be added in subsequent patches.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different versions of EF100 firmware and FPGA bitstreams support different
matching capabilities in the Match-Action Engine. Probe for these at
start of day; subsequent patches will validate TC offload requests
against the reported capabilities.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing inserts into this table yet, but we have code to remove rules
on FLOW_CLS_DESTROY or at driver teardown time, in both cases also
attempting to remove the corresponding hardware rules.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC offload support will involve complex limitations on what matches and
actions a rule can do, in some cases potentially depending on rules
already offloaded. So add an ethtool private flag "log-tc-errors" which
controls reporting the reasons for un-offloadable TC rules at NETIF_INFO.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bind indirect blocks for recognised tunnel netdevices.
Currently these connect to a stub efx_tc_flower() that only returns
-EOPNOTSUPP; subsequent patches will implement flower offloads to the
Match-Action Engine.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bind direct blocks for the MAE-admin PF and each VF representor.
Currently these connect to a stub efx_tc_flower() that only returns
-EOPNOTSUPP; subsequent patches will implement flower offloads to the
Match-Action Engine.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ets qdisc which allows to mix strict priority with bandwidth-sharing
bands. The ets qdisc needs to be attached as root qdisc.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lan966x switch supports credit based shaper in hardware according to
IEEE Std 802.1Q-2018 Section 8.6.8.2. Add support for cbs configuration
on egress port of lan966x switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tbf qdisc allows to attach a shaper on traffic egress on a port or
on a queue. On port they are attached directly to the root and on queue
they are attached on one of the classes of the parent qdisc.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove structs which are no longer used in the driver:
mlx5dr_cmd_qp_create_attr
mlx5_fs_dr_ns
mlx5_pas
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Remove functions which are no longer used in the driver:
mlx5e_ipsec_is_tx_flow
mlx5_health_flush
get_cqe_enhanced_num_mini_cqes
get_cqe_l3_hdr_type
mlx5_health_flush
mlx5_fs_is_ipsec_flow
_mlx5_fs_is_outer_ipproto_flow
mlx5_fs_is_outer_tcp_flow
mlx5_fs_is_outer_udp_flow
mlx5_fs_is_vxlan_flow
mlx5_fs_is_outer_ipsec_flow
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Use port selection capability port_select_flow_table_bypass
bit to detect and enable explicit port affinity even when
in lag hash mode.
Signed-off-by: Liu, Changcheng <jerrliu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The firmware supports adding a steering rule to catch egress traffic
of the QPs/TISs which are set port affinity explicitly in hash mode.
Enable that mode for NICS with 2 ports as well.
Signed-off-by: Liu, Changcheng <jerrliu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
active_port bit mask indicates the current active ports. Set bit indicates
the port is active. Update active ports info to FW to redirect the QP/TIS
from inactive ports to other ports.
Signed-off-by: Liu, Changcheng <jerrliu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In hash mode, without setting tx affinity explicitly, the port select
flow table decides which port is used for the traffic.
If port_select_flow_table_bypass capability is supported and tx affinity
is set explicitly for QP/TIS, they will be added into the explicit affinity
table in FW to check which port is used for the traffic.
1. The overloaded explicit affinity table may affect performance.
To avoid this, do not set tx affinity explicitly by default.
2. The packets of the same flow need to be transmitted on the same port.
Because the packets of the same flow use different QPs in slow & fast
path, it shouldn't set tx affinity explicitly for these QPs.
Signed-off-by: Liu, Changcheng <jerrliu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add support for setting NPPS. NPPS is currently available in
REAL_TIME_CLOCK mode only. In addition allow the user to set the pulse
duration.
When NPPS pulse duration is not set explicitly by the user, driver set
it to 50% of the NPPS period.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
AF_XDP Tx descriptor cleaning in ice driver currently works in a "lazy"
way - descriptors are not cleaned immediately after send. We rather hold
on with cleaning until we see that free space in ring drops below
particular threshold. This was supposed to reduce the amount of
unnecessary work related to cleaning and instead of keeping the ring
empty, ring was rather saturated.
In AF_XDP realm cleaning Tx descriptors implies producing them to CQ.
This is a way of letting know user space that particular descriptor has
been sent, as John points out in [0].
We tried to implement serial descriptor cleaning which would be used in
conjunction with batched cleaning but it made code base more convoluted
and probably harder to maintain in future. Therefore we step away from
batched cleaning in a current form in favor of an approach where we set
RS bit on every last descriptor from a batch and clean always at the
beginning of ice_xmit_zc().
This means that we give up a bit of Tx performance, but this doesn't
hurt l2fwd scenario which is way more meaningful than txonly as this can
be treaten as AF_XDP based packet generator. l2fwd is not hurt due to
the fact that Tx side is much faster than Rx and Rx is the one that has
to catch Tx up.
FWIW Tx descriptors are still produced in a batched way.
[0]: https://lore.kernel.org/bpf/62b0a20232920_3573208ab@john.notmuch/
Fixes: 126cdfe100 ("ice: xsk: Improve AF_XDP ZC Tx and use batching API")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make sure that devlink port is registered first and register netdev
after. Unregister netdev before devlnk port unregister.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that netdevice is registered/unregistered while devlink port
is registered.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the order of destroy_netdev() flow and unregister the devlink port
after calling unregister_netdev().
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As sizeof(hwe->data) can now longer be used as the actual size depends
on foe_entry_size, in commit 9d8cb4c096
("net: ethernet: mtk_eth_soc: add foe_entry_size to mtk_eth_soc") the
use of sizeof(hwe->data) is hence replaced.
However, replacing it with ppe->eth->soc->foe_entry_size is wrong as
foe_entry_size represents the size of the whole descriptor and not just
the 'data' field.
Fix this by subtracing the size of the only other field in the struct
'ib1', so we actually end up with the correct size to be copied to the
data field.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: 9d8cb4c096 ("net: ethernet: mtk_eth_soc: add foe_entry_size to mtk_eth_soc")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/YzBqPIgQR2gLrPoK@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In function mtk_foe_entry_set_vlan() the call to field accessor macro
FIELD_GET(MTK_FOE_IB1_BIND_VLAN_LAYER, entry->ib1)
has been wrongly replaced by
mtk_prep_ib1_vlan_layer(eth, entry->ib1)
Use correct helper function mtk_get_ib1_vlan_layer instead.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: 03a3180e5c ("net: ethernet: mtk_eth_soc: introduce flow offloading support for mt7986")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/YzBp+Kk04CFDys4L@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit fixes DMA engine reset timeout issue in suspend/resume
with ADLink I-Pi SMARC Plus board which dmesg shows:
...
[ 54.678271] PM: suspend exit
[ 54.754066] intel-eth-pci 0000:00:1d.2 enp0s29f2: PHY [stmmac-3:01] driver [Maxlinear Ethernet GPY215B] (irq=POLL)
[ 54.755808] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-0
...
[ 54.780482] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-7
[ 55.784098] intel-eth-pci 0000:00:1d.2: Failed to reset the dma
[ 55.784111] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_hw_setup: DMA engine initialization failed
[ 55.784115] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_open: Hw setup failed
...
The issue is related with serdes which impacts clock. There is
serdes in ADLink I-Pi SMARC board ethernet controller. Please refer to
commit b9663b7ca6 ("net: stmmac: Enable SERDES power up/down sequence")
for detial. When issue is reproduced, DMA engine clock is not ready
because serdes is not powered up.
To reproduce DMA engine reset timeout issue with hardware which has
serdes in GBE controller, install Ubuntu. In Ubuntu GUI, click
"Power Off/Log Out" -> "Suspend" menu, it disables network interface,
then goes to sleep mode. When it wakes up, it enables network
interface again. Stmmac driver is called in this way:
1. stmmac_release: Stop network interface. In this function, it
disables DMA engine and network interface;
2. stmmac_suspend: It is called in kernel suspend flow. But because
network interface has been disabled(netif_running(ndev) is
false), it does nothing and returns directly;
3. System goes into S3 or S0ix state. Some time later, system is
waken up by keyboard or mouse;
4. stmmac_resume: It does nothing because network interface has
been disabled;
5. stmmac_open: It is called to enable network interace again. DMA
engine is initialized in this API, but serdes is not power on so
there will be DMA engine reset timeout issue.
Similarly, serdes powerdown should be added in stmmac_release.
Network interface might be disabled by cmd "ifconfig eth0 down",
DMA engine, phy and mac have been disabled in ndo_stop callback,
serdes should be powered down as well. It doesn't make sense that
serdes is on while other components have been turned off.
If ethernet interface is in enabled state(netif_running(ndev) is true)
before suspend/resume, the issue couldn't be reproduced because serdes
could be powered up in stmmac_resume.
Because serdes_powerup is added in stmmac_open, it doesn't need to be
called in probe function.
Fixes: b9663b7ca6 ("net: stmmac: Enable SERDES power up/down sequence")
Signed-off-by: Junxiao Chang <junxiao.chang@intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Jimmy JS Chen <jimmyjs.chen@adlinktech.com>
Tested-by: Looi, Hong Aun <hong.aun.looi@intel.com>
Link: https://lore.kernel.org/r/20220923050448.1220250-1-junxiao.chang@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The SXD, TXD, and RXD macros are used only once (or twice). Just use the
vdbg print, which seems to have been devised for these sorts of very
verbose messages.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver seems to have been written under the assumption that messages
can be continued arbitrarily. I'm not when this changed (if ever), but such
ad-hoc continuations are liable to be rudely interrupted. Convert all such
instances to single prints. This loses a bit of timing information (such as
when a line was constructed piecemeal as the function executed), but it's
easy to add a few prints if necessary. This also adds newlines to the ends
of any prints without them.
Since (almost every) debug print included the name of the function, include
it automatically.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wherever possible, use the associated netdev (or device) when printing
errors or other messages. This makes it immediately clear what device
caused the error, and provides more information than just the device name.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a mostly-mechanical translation of the existing printks into
pr_foos. In several places, I have pasted messages which were broken over
several lines to allow for easier grepping.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove all the single-use debug conditionals, and just collect the debug
defines at the top of the file. HMD seems like it is used for general debug
info, so just redefine it as pr_debug. Additionally, instead of using the
default loglevel, use the debug loglevel for debugging.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
