Currently `sp_indiff` is cleaned when driver is removed. This will
cause problem in multi-PF/multi-host case, considering one PF is
removed while another is still in use.
Since `sp_indiff` is the application firmware property, it should
only be cleaned when the firmware is unloaded. Now let management
firmware to clean it when necessary, driver only set it.
Fixes: b1e4f11e42 ("nfp: refine the ABI of getting `sp_indiff` info")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20221020081411.80186-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support restart of link auto-negotiation.
This may be initiated using:
# ethtool -r <intf>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Report the auto negotiation capability if it's supported
in management firmware, and advertise it if it's enabled.
Changing port speed is not allowed when autoneg is enabled.
The ethtool <intf> command displays the auto-neg capability:
# ethtool enp1s0np0
Settings for enp1s0np0:
Supported ports: [ FIBRE ]
Supported link modes: Not reported
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Supported FEC modes: None RS BASER
Advertised link modes: Not reported
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: None RS BASER
Speed: 25000Mb/s
Duplex: Full
Auto-negotiation: on
Port: FIBRE
PHYAD: 0
Transceiver: internal
Link detected: yes
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Considering that whether application firmware is indifferent to
port speed is a firmware property instead of port property, now use
a new rtsym to get the property instead of parsing per-port tlv caps.
With this change, relevant code is moved to `nfp_main` layer.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's not a fatal error when setting `hwinfo` into management firmware
fails, no need to halt the whole driver initialization process.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The latest management firmware can now report the active FEC
mode. Adapt driver accordingly so that user can get the active
FEC mode by running command:
# ethtool --show-fec <intf>
Also correct use of `fec` field.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
support ct nat action when pre_ct merge with post_ct
and nft. at the same time, add the extra checksum action
and hardware stats for nft to meet the action check when
do nat.
Signed-off-by: Hui Zhou <hui.zhou@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Validation of police actions was added to offload drivers in
commit d97b4b105c ("flow_offload: reject offload for all drivers with
invalid police parameters")
This patch extends that validation in the nfp driver to include
police actions which are created independently of flows.
Signed-off-by: Ziyang Chen <ziyang.chen@corigine.com>
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will soon introduce an optional per-netns ehash.
This means we cannot use tcp_hashinfo directly in most places.
Instead, access it via net->ipv4.tcp_death_row.hashinfo.
The access will be valid only while initialising tcp_hashinfo
itself and creating/destroying each netns.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for eeprom get and set operation with ethtool command.
with this change, we can support commands as:
#ethtool -e enp101s0np0 offset 0 length 6
Offset Values
------ ------
0x0000: 00 15 4d 16 66 33
#ethtool -E enp101s0np0 magic 0x400019ee offset 5 length 1 value 0x88
We make this change to persist MAC change during driver reload and system
reboot.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A new tlv type is introduced to indicate if application firmware is
indifferent to port speed, and inform management firmware of the
result.
And the result is always true for flower application firmware since
it's indifferent to port speed from the start and will never change.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In future releases the NIC application firmware may be indifferent to port
speeds - not built for specific port speeds - and consequently it will not
be able to report VF port speeds to the driver without first learning them.
With this change, the driver will pass the speed of physical ports from
management firmware to application firmware, and the latter will copy the
speed of port 0 to all the active VFs. So that the driver can get VF port
speed as before.
The port speed of a VF may be requested from userspace using:
ethtool <vf-intf>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
is_post_ct_flow() function will process only ct_state ESTABLISHED,
then offload_pre_check() function will check FLOW_DISSECTOR_KEY_CT flag.
When config tc filter match ct_state(0/0x3f), dissector->used_keys
with FLOW_DISSECTOR_KEY_CT bit, function offload_pre_check() will
return false, so not offload. This is a special case that can be handled
safely.
Therefore, modify to let initial packet which won't go through conntrack
can be offloaded, as long as the cared ct fields are all zero.
Signed-off-by: Wenjuan Geng <wenjuan.geng@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220823090122.403631-1-simon.horman@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
area_cache_get() is used to distribute cache->area and set cache->id,
and if cache->id is not 0 and cache->area->kref refcount is 0, it will
release the cache->area by nfp_cpp_area_release(). area_cache_get()
set cache->id before cpp->op->area_init() and nfp_cpp_area_acquire().
But if area_init() or nfp_cpp_area_acquire() fails, the cache->id is
is already set but the refcount is not increased as expected. At this
time, calling the nfp_cpp_area_release() will cause use-after-free.
To avoid the use-after-free, set cache->id after area_init() and
nfp_cpp_area_acquire() complete successfully.
Note: This vulnerability is triggerable by providing emulated device
equipped with specified configuration.
BUG: KASAN: use-after-free in nfp6000_area_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:760)
Write of size 4 at addr ffff888005b7f4a0 by task swapper/0/1
Call Trace:
<TASK>
nfp6000_area_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:760)
area_cache_get.constprop.8 (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:884)
Allocated by task 1:
nfp_cpp_area_alloc_with_name (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:303)
nfp_cpp_area_cache_add (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:802)
nfp6000_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:1230)
nfp_cpp_from_operations (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:1215)
nfp_pci_probe (drivers/net/ethernet/netronome/nfp/nfp_main.c:744)
Freed by task 1:
kfree (mm/slub.c:4562)
area_cache_get.constprop.8 (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:873)
nfp_cpp_read (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:924 drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:973)
nfp_cpp_readl (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cpplib.c:48)
Signed-off-by: Jialiang Wang <wangjialiang0806@163.com>
Reviewed-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220810073057.4032-1-wangjialiang0806@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The port flag isn't set to `NFP_PORT_CHANGED` when using
`ethtool -m DEVNAME` before, so the port state (e.g. interface)
cannot be updated. Therefore, it caused that `ethtool -m DEVNAME`
sometimes cannot read the correct information.
E.g. `ethtool -m DEVNAME` cannot work when load driver before plug
in optical module, as the port interface is still NONE without port
update.
Now update the port state before sending info to NIC to ensure that
port interface is correct (latest state).
Fixes: 61f7c6f448 ("nfp: implement ethtool get module EEPROM")
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220802093355.69065-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While reading sysctl_ip_default_ttl, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_tun_write_neigh() function will configure a tunnel neighbour when
calling nfp_tun_neigh_event_handler() or nfp_flower_cmsg_process_one_rx()
(with no tunnel neighbour type) from firmware.
When configuring IP on physical port as a tunnel endpoint, no operation
will be performed after receiving the cmsg mentioned above.
Therefore, add a progress to configure tunnel neighbour in this case.
v2: Correct format of fixes tag.
Fixes: f1df7956c1 ("nfp: flower: rework tunnel neighbour configuration")
Signed-off-by: Tianyu Yuan <tianyu.yuan@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220714081915.148378-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for TX VLAN ctag insert
which may be configured via ethtool.
e.g.
# ethtool -K $DEV tx-vlan-offload on
The NIC supplies VLAN insert information as packet metadata.
The fields of this VLAN metadata including vlan_proto and vlan tag.
Configuration control bit NFP_NET_CFG_CTRL_TXVLAN_V2 is to
signal availability of ctag-insert features of the firmware.
NFDK is used to communicate via PCIE to NFP-3800 based NICs
while NFD3 is used for other NICs supported by the NFP driver.
This features is currently implemented only for NFD3 and
this patch adds support for it with NFDK.
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220711093048.1911698-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building with Clang we encounter these warnings:
| drivers/net/ethernet/netronome/nfp/nfp_app.c:233:99: error: format
| specifies type 'unsigned char' but the argument has underlying type
| 'unsigned int' [-Werror,-Wformat] nfp_err(pf->cpp, "unknown FW app ID
| 0x%02hhx, driver too old or support for FW not built in\n", id);
-
| drivers/net/ethernet/netronome/nfp/nfp_main.c:396:11: error: format
| specifies type 'unsigned char' but the argument has type 'int'
| [-Werror,-Wformat] serial, interface >> 8, interface & 0xff);
Correct format specifier for `id` is `%x` since the default type for the
`nfp_app_id` enum is `unsigned int`. The second warning is also solved
by using the `%x` format specifier as the expressions involving
`interface` are implicity promoted to integers (%x is used to maintain
hexadecimal representation).
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220712000152.2292031-1-justinstitt@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TCP packets will be dropped if the segments number in the tx skb
exceeds limitation when sending iperf3 traffic with --zerocopy option.
we make the following changes:
Get nr_frags in nfp_nfdk_tx_maybe_close_block instead of passing from
outside because it will be changed after skb_linearize operation.
Fill maximum dma_len in first tx descriptor to make sure the whole
head is included in the first descriptor.
Fixes: c10d12e3dc ("nfp: add support for NFDK data path")
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets with metadata prepended can be correctly handled in
firmware when TSO is enabled, now remove the error path and
related comments. Since there's no existing firmware that
uses prepended metadata, no need to add compatibility check
here.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TX VLAN ctag insert
which may be configured via ethtool.
e.g.
# ethtool -K $DEV tx-vlan-offload on
The NIC supplies VLAN insert information as packet metadata.
The fields of this VLAN metadata are gotten from sk_buff, including
vlan_proto and vlan tag.
Configuration control bit NFP_NET_CFG_CTRL_TXVLAN_V2 is to
signal availability of ctag-insert features of the firmware.
NFDK is used to communicate via PCIE to NFP-3800 based NICs
while NFD3 is used for other NICs supported by the NFP driver.
The metadata format on tx side of NFD3 is different from NFDK.
This feature is not currently implemented for NFDK.
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RX VLAN ctag/stag strip
which may be configured via ethtool.
e.g.
# ethtool -K $DEV rx-vlan-offload on
# ethtool -K $DEV rx-vlan-stag-hw-parse on
Ctag-stripped and stag-stripped cannot be enabled at the same time
because currently the kernel supports only one layer of VLAN stripping.
The NIC supplies VLAN strip information as packet metadata.
The fields of this VLAN metadata are:
* strip flag: 1 for stripped; 0 for unstripped
* tci: VLAN TCI ID
* tpid: 1 for ETH_P_8021AD; 0 for ETH_P_8021Q
Configuration control bits NFP_NET_CFG_CTRL_RXVLAN_V2 and
NFP_NET_CFG_CTRL_RXQINQ are to signal availability of
ctag-strip and stag-strip features of the firmware.
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)"
to compute headers length for a TCP packet, but others
use more convoluted (but equivalent) ways.
Add skb_tcp_all_headers() and skb_inner_tcp_all_headers()
helpers to harmonize this a bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support VF rate limiting with NFDK by adding ndo_set_vf_rate to the NFDK
ops structure.
NFDK is used to communicate via PCIE to NFP-3800 based NICs
while NFD3 is used for other NICs supported by the NFP driver.
The VF rate limit feature is already supported by the driver for NFD3.
Signed-off-by: Bin Chen <bin.chen@corigine.com>
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of spelling and language mistakes in the flower section are
fixed. The spacing between the text inside some comments and the comment
symbols are also updated for consistency.
Signed-off-by: Walter Heymans <walter.heymans@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ethtool selftest.
e.g.
# ethtool -t DEVNAME
test result like:
The test result is PASS
The test extra info:
Link Test 0
NSP Test 0
Firmware Test 0
Register Test 0
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for VEPA mode of HW bridge.
The default remains VEB mode.
The mode may be configured using ndo_bridge_setlink,
and inspected using ndo_bridge_getlink.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During initialization of the NFP driver, a file name for loading
application firmware is composed using the NIC's AMDA information and port
type (count and speed). E.g.: "nic_AMDA0145-1012_2x10.nffw".
In practice there may be many variants for each NIC type, and many of the
variants relate to assembly components which do not concern the driver and
application firmware implementation. Yet the current scheme leads to a
different application firmware file name for each variant, because they
have different AMDA information.
To reduce proliferation of content-duplicated application firmware images
or symlinks, the NIC's management firmware will only expose differences
between variants that need different application firmware via a newly
introduced hwinfo, "nffw.partno".
Use of the existing hwinfo, "assembly.partno", is maintained in order to
support for NICs with management firmware that does not expose
"nffw.partno".
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220620103912.46164-1-simon.horman@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This reverts commit 9386ebccfc ("nfp: update nfp_X logging definitions")
The reverted patch was intended to improve logging for the NFP driver by
including information such as the source code file and number in log
messages.
Unfortunately our experience is that this has not improved things as
we had hoped. The resulting logs are inconsistent with (most) other
kernel log messages. And rely on knowledge of the source code version
in order for the extra information to be useful.
Thus, revert the change.
We acknowledge that Jakub Kicinski <kuba@kernel.org> foresaw this problem.
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
48-bit DMA addressing is supported in NFP3800 HW and implemented
in NFDK firmware, so enable this feature in driver now. Note that
with this change, NFD3 firmware, which doesn't implement 48-bit
DMA, cannot be used for NFP3800 any more.
RX free list descriptor, used by both NFD3 and NFDK, is also modified
to support 48-bit DMA. That's OK because the top bits is always get
set to 0 when assigned with 40-bit address.
Based on initial work of Jakub Kicinski <jakub.kicinski@netronome.com>.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
