Currently we don't clear MSDC interrupts when cqe off/disable, which led
to the data complete interrupt will be reserved for the next command.
If the next command with data transfer after cqe off/disable, we process
the CMD ready interrupt and trigger DMA start for data, but the data
complete interrupt is already exists, then SW assume that the data transfer
is complete, SW will trigger DMA stop, but the data may not be transmitted
yet or is transmitting, so we may encounter the following error:
mtk-msdc 11230000.mmc: CMD bus busy detected.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Fixes: 88bd652b3c ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220728080048.21336-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for eint IRQ when MSDC is used as an SDIO host. This
feature requires SDIO device support async IRQ function. With this
feature, SDIO host can be awakened by SDIO card in suspend state,
without additional pin.
MSDC driver will time-share the SDIO DAT1 pin. During suspend, MSDC
turn off clock and switch SDIO DAT1 pin to GPIO mode. And during
resume, switch GPIO function back to DAT1 mode then turn on clock.
Some device tree property should be added or modified in MSDC node
to support SDIO eint IRQ. Pinctrls "state_eint" is mandatory. Since
this feature depends on asynchronous interrupts, "wakeup-source",
"keep-power-in-suspend" and "cap-sdio-irq" flags are necessary, and
the interrupts list should be extended(the interrupt named with
sdio_wakeup):
&mmcX {
...
interrupt-names = "msdc", "sdio_wakeup";
interrupts-extended = <...>,
<&pio xxx IRQ_TYPE_LEVEL_LOW>;
...
pinctrl-names = "default", "state_uhs", "state_eint";
...
pinctrl-2 = <&mmc2_pins_eint>;
...
cap-sdio-irq;
keep-power-in-suspend;
wakeup-source;
...
};
Co-developed-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-4-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MediaTek IP requires that after dma stop, it need to wait this dma stop
bit auto-reset to 0. When bus is in high loading state, it will take a
while for the dma stop complete. If there is no waiting operation here,
when program runs to clear fifo and reset, bus will hang.
In addition, there should be no return in msdc_data_xfer_next() if
there is data need be transferred, because no matter what error occurs
here, it should continue to excute to the following mmc_request_done.
Otherwise the core layer may wait complete forever.
Signed-off-by: Mengqi Zhang <mengqi.zhang@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220609112239.18911-1-mengqi.zhang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 3c1a884436 ("mmc: mediatek: add support of source_cg clock")
an independent cg was introduced to avoid a hardware hang issue during
clock mode switches (subsequent commits will set that clock as optional).
When this clock is not present in device-tree, any operation is being
done on src_clk's parent (calling clk_get_parent()): to simplify this
and avoid checking for src_clk_cg presence everytime, just assign the
parent clock to src_clk_cg and remove the now useless checks.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to JEDEC Spec, there is no need to do tuning under HS400 mode
since the Rx signal is aligned with the DS signal. However, MediaTek's IC
need set its "DS delay" internally to ensure it can latch Rx signal
correctly.
In previous version, We provide an "hs400-ds-delay" in device tree to cover
different chipset/PCB design, and it works fine in most cases. But, with
the development of process technology and the big VCore voltage scale
range(may have 0.7V/0.6V/0.55V), it is difficult to find a suitable
"hs400-ds-delay" to cover all of IC corner cases(SSSS/TTTT/FFFF). So that
We must have the ability to do hs400 online tuning.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20210917124803.22871-4-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We found this issue on a 5G platform, during CMDQ error handling, if DMA
status is active when it call msdc_reset_hw(), it means mmc host hw reset
and DMA transfer will be parallel, mmc host may access sram region
unexpectedly. According to the programming guide of mtk-sd host, it needs
to wait for dma stop done after set dma stop.
This change should be applied to all SoCs.
Signed-off-by: Derong Liu <derong.liu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210827071537.1034-1-derong.liu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when get request SW timeout, if CMD/DAT xfer done irq coming right now,
then there is race between the msdc_request_timeout work and irq handler,
and the host->cmd and host->data may set to NULL in irq handler. also,
current flow ensure that only one path can go to msdc_request_done(), so
no need check the return value of cancel_delayed_work().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The #ifdef check for the suspend/resume functions is wrong:
drivers/mmc/host/mtk-sd.c:2765:12: error: unused function 'msdc_suspend' [-Werror,-Wunused-function]
static int msdc_suspend(struct device *dev)
drivers/mmc/host/mtk-sd.c:2779:12: error: unused function 'msdc_resume' [-Werror,-Wunused-function]
static int msdc_resume(struct device *dev)
Remove the #ifdef and mark all four as __maybe_unused to aovid the
problem.
Fixes: c0a2074ac5 ("mmc: mediatek: Fix system suspend/resume support for CQHCI")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201203222922.1067522-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MediaTek MMC driver uses pointer to get from private
msdc_host structure to the generic mmc_host structure.
However mmc_host always precedes msdc_host in memory so compute
its address with a subtraction (which is cheaper than a dereference)
using mmc_from_priv() and drop the extra pointer.
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Link: https://lore.kernel.org/r/20200917192624.548720-1-ameynarkhede03@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixs eMMC-Access on mt7622/Bpi-64.
Before we got these Errors on mounting eMMC ion R64:
[ 48.664925] blk_update_request: I/O error, dev mmcblk0, sector 204800 op 0x1:(WRITE)
flags 0x800 phys_seg 1 prio class 0
[ 48.676019] Buffer I/O error on dev mmcblk0p1, logical block 0, lost sync page write
This patch adds a optional reset management for msdc.
Sometimes the bootloader does not bring msdc register
to default state, so need reset the msdc controller.
Cc: <stable@vger.kernel.org> # v5.4+
Fixes: 966580ad23 ("mmc: mediatek: add support for MT7622 SoC")
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20200814014346.6496-4-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support command queue for mt6779 platform.
a. Add msdc_set_busy_timeout() to calculate emmc write timeout.
b. Connect mtk msdc driver to cqhci driver through
host->cq_host->ops = &msdc_cmdq_ops;
c. msdc_cmdq_irq() will link up with cqchi_irq(). Besides, it provides
more irq error messages like RSPCRCERR/CMDTO/DATACRCERR/DATTMO.
d. Select kernel config MMC_CQHCI for MMC_MTK
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/1595205759-5825-4-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for
the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would
happen if the signal voltage switch did NOT happen, because the voltage was
already set correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de
[Ulf: Re-worked/simplified the code a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO irq is not triggered by low level, but by falling edge in our
previous IC. This mechanism only have one chance to catch the SDIO irq
if a SDIO irq comes within the multiple block transmission. This SDIO
irq may be easily lost, because falling edge appears only once within 2
clock after data transmission is completed.
SDIO irq recheck mechanism will make sure all irqs can be
processed correctly.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/1585299097-6897-2-git-send-email-yong.mao@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means msdc_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the mtk-sd
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the mtk-sd driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the mtk-sd driver, so let's do that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO IRQ is not defaultly triggered by low level,
but by falling edge. It needs to set related register
to enable SDIO IRQ low level trigger function.
Otherwise the SDIO IRQ may be lost in some specail condition.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MSDC IP which support 64G DRAM will support 24bits BDMA buffer length,
so add support it.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when plug out SD card, may get data CRC error, the MMC core will issue
CMD13 to get card status, then CMD13 timeout(due to card plug out) will
trigger CMD19 tuning, first CMD19 timeout has not call msdc_reset_hw()
and cause the next CMD19 gets controller busy.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
