Noticed this while trying to debug some unrelated issues: this laptop has
the ability to use rmi4 but doesn't by default. So let's fix that.
Tested locally, including mouse buttons, on my ThinkPad P1 G3. This might
also enable the X1 Extreme G3, but I don't have such a system to test
locally (presumably Mark can chime in if that's the case).
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20220909202127.141761-1-lyude@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices expose an ultra-low-power (ULP) mode entry mask for
each channel. If the mask is set, the device cannot enter ULP so
long as the corresponding channel remains in an active state.
The vendor has advised setting the mask for any disabled channel.
To accommodate this suggestion, initially set all masks and then
clear them only if specified in the device tree.
Fixes: e505edaedc ("Input: add support for Azoteq IQS7222A/B/C")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20220908131548.48120-8-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
An effort has been made to support every official model and firmware
version I could track down info on. The following controllers _should_
have working paddles with this PR:
- Xbox Elite (**untested**)
- Xbox Elite Series 2 on early firmwares (**untested**)
- Xbox Elite Series 2 on v4 firmwares (Tested v4.8.1908.0)
- Xbox Elite Series 2 on v5 pre-BLE firmwares (**untested**)
- Xbox Elite Series 2 on v5 post-BLE firmwares (Tested v5.13.3143.0)
This patch also introduces correct handling for the Elite 1 controller
and properly suppresses paddle inputs when using a custom profile slot.
Starting with firmware v5.11, certain inputs for the Elite 2 were moved
to an extra packet that is not enabled by default.
We must first manually enable this extra packet in order to correctly
process paddle input data with these later firmwares.
Signed-off-by: Christopher Crockett <chaorace@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20220818154411.510308-5-rojtberg@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Suspending and resuming the system can sometimes cause the out
URB to get hung after a reset_resume. This causes LED setting
and force feedback to break on resume. To avoid this, just drop
the reset_resume callback so the USB core rebinds xpad to the
wireless pads on resume if a reset happened.
A nice side effect of this change is the LED ring on wireless
controllers is now set correctly on system resume.
Cc: stable@vger.kernel.org
Fixes: 4220f7db1e ("Input: xpad - workaround dead irq_out after suspend/ resume")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Link: https://lore.kernel.org/r/20220818154411.510308-3-rojtberg@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- GT1158 ID added to Goodix touchscreen driver
- Boeder Force Feedback Wheel USB added to iforce joystick driver
- fixup for iforce driver to avoid hangups
- fix autoloading of rk805-pwrkey driver.
* tag 'input-for-v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: iforce - add support for Boeder Force Feedback Wheel
Input: iforce - wake up after clearing IFORCE_XMIT_RUNNING flag
Input: goodix - add compatible string for GT1158
MAINTAINERS: add include/dt-bindings/input to INPUT DRIVERS
Input: rk805-pwrkey - fix module autoloading
Input: goodix - add support for GT1158
dt-bindings: input: touchscreen: add compatible string for Goodix GT1158
Use firmware properties (eg: OF) to get the device specific
configuration. This change just replaces the platform data since there
was no platform using it and so, it makes no sense having both.
Special note to the PULL-UP disable setting that is now supported as
part of the gpio subsystem (using 'set_config()' callback).
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220829131553.690063-5-nuno.sa@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change replaces the support for GPIs as key event generators.
Instead of reporting the events directly, we add a gpio based irqchip
so that these events can be consumed by keys defined in the gpio-keys
driver (as it's goal is indeed for keys on GPIOs capable of generating
interrupts). With this, the gpio-adp5588 driver can also be dropped.
The basic idea is that all the pins that are not being used as part of
the keymap matrix can be possibly requested as GPIOs by gpio-keys
(it's also fine to use these pins as plain interrupts though that's not
really the point).
Since the gpiochip now also has irqchip capabilities, we should only
remove it after we free the device interrupt (otherwise we could, in
theory, be handling GPIs interrupts while the gpiochip is concurrently
removed). Thus the call 'adp5588_gpio_add()' is moved and since the
setup phase also needs to come before making the gpios visible, we also
need to move 'adp5588_setup()'.
While at it, always select GPIOLIB so that we don't need to use #ifdef
guards.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220829131553.690063-2-nuno.sa@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- changes to input core to properly queue synthetic events (such as
autorepeat) and to release multitouch contacts when an input device
is inhibited or suspended
- reworked quirk handling in i8042 driver that consolidates multiple
DMI tables into one and adds several quirks for TUXEDO line of
laptops
- update to mt6779 keypad to better reflect organization of the
hardware
- changes to mtk-pmic-keys driver preparing it to handle more variants
- facelift of adp5588-keys driver
- improvements to iqs7222 driver
- adjustments to various DT binding documents for input devices
- other assorted driver fixes.
* tag 'input-for-v5.20-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: adc-joystick - fix ordering in adc_joystick_probe()
dt-bindings: input: ariel-pwrbutton: use spi-peripheral-props.yaml
Input: deactivate MT slots when inhibiting or suspending devices
Input: properly queue synthetic events
dt-bindings: input: iqs7222: Use central 'linux,code' definition
Input: i8042 - add dritek quirk for Acer Aspire One AO532
dt-bindings: input: gpio-keys: accept also interrupt-extended
dt-bindings: input: gpio-keys: reference input.yaml and document properties
dt-bindings: input: gpio-keys: enforce node names to match all properties
dt-bindings: input: Convert adc-keys to DT schema
dt-bindings: input: Centralize 'linux,input-type' definition
dt-bindings: input: Use common 'linux,keycodes' definition
dt-bindings: input: Centralize 'linux,code' definition
dt-bindings: input: Increase maximum keycode value to 0x2ff
Input: mt6779-keypad - implement row/column selection
Input: mt6779-keypad - match hardware matrix organization
Input: i8042 - add additional TUXEDO devices to i8042 quirk tables
Input: goodix - switch use of acpi_gpio_get_*_resource() APIs
Input: i8042 - add TUXEDO devices to i8042 quirk tables
Input: i8042 - add debug output for quirks
...
MediaTek keypad has 2 modes of detecting key events:
- single key: each (row, column) can detect one key
- double key: each (row, column) is a group of 2 keys
Double key support exists to minimize cost, since it reduces the number
of pins required for physical keys.
Double key is configured by setting BIT(0) of the KP_SEL register.
Enable double key matrix support based on the mediatek,keys-per-group
device tree property.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220720-mt8183-keypad-v2-5-6d42c357cb76@baylibre.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull parisc updates from Helge Deller:
"One real bugfix to change the io_pgetevents_time64() syscall to use
the compat implementation when running in compat mode, otherwise the
signed int32 parameters min_nr and nr will be incorrectly handled as
unsigned int64 values.
Other than that just small cleanups:
- hardware database housekeeping and proper /proc/iomem output
- add proper function exit code if probe functions fail
- drop stale variables (pa_swapper_pg_lock)
- drop unneccessary zero-initializations
- typo fixes in comments"
* tag 'for-5.20/parisc-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
Input: gscps2 - check return value of ioremap() in gscps2_probe()
parisc: io_pgetevents_time64() needs compat syscall in 32-bit compat mode
parisc: Drop zero variable initialisations in mm/init.c
parisc: Do not initialise statics to 0
parisc: Check the return value of ioremap() in lba_driver_probe()
parisc: Drop pa_swapper_pg_lock spinlock
parisc: Fix comment typo in fault.c
parisc: Fix device names in /proc/iomem
parisc: Clean up names in hardware database
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
Pull EFI updates from Ard Biesheuvel:
- Enable mirrored memory for arm64
- Fix up several abuses of the efivar API
- Refactor the efivar API in preparation for moving the 'business
logic' part of it into efivarfs
- Enable ACPI PRM on arm64
* tag 'efi-next-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi: (24 commits)
ACPI: Move PRM config option under the main ACPI config
ACPI: Enable Platform Runtime Mechanism(PRM) support on ARM64
ACPI: PRM: Change handler_addr type to void pointer
efi: Simplify arch_efi_call_virt() macro
drivers: fix typo in firmware/efi/memmap.c
efi: vars: Drop __efivar_entry_iter() helper which is no longer used
efi: vars: Use locking version to iterate over efivars linked lists
efi: pstore: Omit efivars caching EFI varstore access layer
efi: vars: Add thin wrapper around EFI get/set variable interface
efi: vars: Don't drop lock in the middle of efivar_init()
pstore: Add priv field to pstore_record for backend specific use
Input: applespi - avoid efivars API and invoke EFI services directly
selftests/kexec: remove broken EFI_VARS secure boot fallback check
brcmfmac: Switch to appropriate helper to load EFI variable contents
iwlwifi: Switch to proper EFI variable store interface
media: atomisp_gmin_platform: stop abusing efivar API
efi: efibc: avoid efivar API for setting variables
efi: avoid efivars layer when loading SSDTs from variables
efi: Correct comment on efi_memmap_alloc
memblock: Disable mirror feature if kernelcore is not specified
...
When inhibiting or suspending a device we are sending release events for
all currently held keys and buttons, however we retain active MT slot
state, which causes issues with gesture recognition when we resume or
uninhibit.
Let's fix it by introducing, in addition to input_dev_release_keys(),
nput_mt_release_slots() that will deactivate all currently active slots.
Signed-off-by: Angela Czubak <acz@semihalf.com>
Link: https://lore.kernel.org/r/20220718151715.1052842-3-acz@semihalf.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
