[Why]
The DIO FIFO will underflow if we turn off the OTG before we turn
off the FIFO.
Since this happens as part of the OTG workaround and we don't reset
the FIFO afterwards we see the error persist.
[How]
Add disable FIFO before the disable CRTC and enable FIFO after enabling
the CRTC.
Reviewed-by: Syed Hassan <Syed.Hassan@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Partially valid EDIDs on MST sinks are treated the same way as broken
EDIDs or read failures and result in a fallback EDID being used instead.
[How]
If edid_status is EDID_PARTIAL_VALID, prefer to use the valid EDID
blocks instead of using a fallback EDID.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Avoids a race condition where DIO FIFO can underflow due to no incoming
data available.
[How]
Shift the FIFO enable below stream enable.
Make sure fullness level is written before the DIO reset takes place
and that we're not doing it twice.
Reviewed-by: Syed Hassan <Syed.Hassan@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Only a single VLINE interrupt is available so interface should not
expose the second one which is used by DMU firmware.
[how]
Remove references to periodic_interrupt1 and VLINE1 from DC interfaces.
Reviewed-by: Jaehyun Chung <jaehyun.chung@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Shader wave interrupts were getting dropped in event_interrupt_wq_v11
if the PRIV bit was set to 1. This would often lead to a hang. Until
debugger logic is upstreamed, expand comment to stop early return.
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update mes_v11_api_def.h add_queue API with is_aql_queue parameter. Also
re-use gds_size for the queue size (unused for KFD). MES requires the
queue size in order to compute the actual wptr offset within the queue
RB since it increases monotonically for AQL queues.
v2: Make is_aql_queue assign clearer
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are used by umr to sort the hive nodes since the kernel
initializes the nodes in order of bus enumeration not XGMI hive
enumeration.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's vbios and pmfw instead of driver who decide whether some dpm features
is supported or not. Driver just de-selects those features which are not
permitted on user's request. Thus, we use adverse selects model.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable verbose while getting p2p distance. With verbose, it shows
warning if ACS redirect is set between the devices. Adds noise
to dmesg logs when a few GPU devices are on the same platform.
Example log:
amdgpu 0000:34:00.0: ACS redirect is set between the client and provider (0000:31:00.0)
amdgpu 0000:34:00.0: to disable ACS redirect for this path, add the kernel parameter:
pci=disable_acs_redir=0000:30:00.0;0000:2e:00.0;0000:33:00.0;0000:2e:10.0
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For the asic using smu v13_0_2, there is the following
warning when uninstalling amdgpu:
amdgpu: ras disable gfx failed poison:1 ret:-22.
[Why]:
For the asic using smu v13_0_2, the psp .suspend and
mode1reset is called before amdgpu_ras_pre_fini during
amdgpu uninstall, it has disabled all ras features and
reset the psp. Since the psp is reset, calling
amdgpu_ras_disable_all_features in amdgpu_ras_pre_fini
to disable ras features will fail.
[How]:
If all ras features are disabled, amdgpu_ras_disable_all_features
will not be called to disable all ras features again.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Register GT0_PERF_LIMIT_REASONS (0x1381a8) is available only for
Gen11+. Therefore ensure perf_limit_reasons sysfs files are created only
for Gen11+. Otherwise on Gen < 5 accessing these files results in the
following oops:
<1> [88.829420] BUG: unable to handle page fault for address: ffffc90000bb81a8
<1> [88.829438] #PF: supervisor read access in kernel mode
<1> [88.829447] #PF: error_code(0x0000) - not-present page
This patch is a backport of the drm-tip commit 0d2d201095e9
("drm/i915: Perf_limit_reasons are only available for Gen11+") to
drm-intel-fixes. The backport is not identical to the original, it only
includes the sysfs portions of if. The debugfs portion is not available
in drm-intel-fixes so has not been backported.
Bspec: 20008
Bug: https://gitlab.freedesktop.org/drm/intel/-/issues/6863
Fixes: fa68bff7cf ("drm/i915/gt: Add sysfs throttle frequency interfaces")
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220919162401.2077713-1-ashutosh.dixit@intel.com
(backported from commit 0d2d201095e9f141d6a9fb44320afce761f8b5c2)
The sequence for Source DP PHY CTS automation is [2][1]:
1- Emulate successful Link Training(LT)
2- Short HPD and change link rates and number of lanes by LT.
(This is same flow for Link Layer CTS)
3- Short HPD and change PHY test pattern and swing/pre-emphasis
levels (This step should not trigger LT)
The problem is with DP PHY compliance setup as follow:
[DPTX + on board LTTPR]------Main Link--->[Scope]
^ |
| |
| |
----------Aux Ch------>[Aux Emulator]
At step 3, before writing TRAINING_LANEx_SET/LINK_QUAL_PATTERN_SET
to declare the pattern/swing requested by scope, we write link
config in LINK_BW_SET/LANE_COUNT_SET on a port that has LTTPR.
As LTTPR snoops aux transaction, LINK_BW_SET/LANE_COUNT_SET writes
indicate a LT will start [Check DP 2.0 E11 -Sec 3.6.8.2 & 3.6.8.6.3],
and LTTPR will reset the link and stop sending DP signals to
DPTX/Scope causing the measurements to fail. Note that step 3 will
not trigger LT and DP link will never recovered by the
Aux Emulator/Scope.
The reset of link can be tested with a monitor connected to LTTPR
port simply by writing to LINK_BW_SET or LANE_COUNT_SET as follow
igt/tools/dpcd_reg write --offset=0x100 --value 0x14 --device=2
OR
printf '\x14' | sudo dd of=/dev/drm_dp_aux2 bs=1 count=1 conv=notrunc
seek=$((0x100))
This single aux write causes the screen to blank, sending short HPD to
DPTX, setting LINK_STATUS_UPDATE = 1 in DPCD 0x204, and triggering LT.
As stated in [1]:
"Before any TX electrical testing can be performed, the link between a
DPTX and DPRX (in this case, a piece of test equipment), including all
LTTPRs within the path, shall be trained as defined in this Standard."
In addition, changing Phy pattern/Swing/Pre-emphasis (Step 3) uses the
same link rate and lane count applied on step 2, so no need to redo LT.
The fix is to not rewrite link config in step 3, and just writes
TRAINING_LANEx_SET and LINK_QUAL_PATTERN_SET
[1]: DP 2.0 E11 - 3.6.11.1 LTTPR DPTX_PHY Electrical Compliance
[2]: Configuring UnigrafDPTC Controller - Automation Test Sequence
https://www.keysight.com/us/en/assets/9922-01244/help-files/
D9040DPPC-DisplayPort-Test-Software-Online-Help-latest.chm
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Or Cochvi <or.cochvi@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916054900.415804-1-khaled.almahallawy@intel.com
msm-next for v6.1
DPU:
- simplified VBIF configuration
- cleaned up CTL interfaces to accept indices rather than flush masks
DSI:
- removed unused msm_display_dsc_config struct
- switch regulator calls to new bulk API
- switched to use PANEL_BRIDGE for directly attached panels
DSI PHY:
- converted drivers to use parent_hws instead of parent_names
DP:
- cleaned up pixel_rate handling
HDMI PHY:
- turned hdmi-phy-8996 into OF clk provider
core:
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
gpu+gem:
- Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduces lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsrfrr9v1oR9S4oYfOs9jm=jbKQiwPBTrCRHrjYerJJFA@mail.gmail.com
- Under SRIOV, we need to send REQ_GPU_FINI to the hypervisor
during the suspend time. Furthermore, we cannot request a
mode 1 reset under SRIOV as VF. Therefore, we will skip it
as it is called in suspend_noirq() function.
- In the resume code path, we need to send REQ_GPU_INIT to the
hypervisor and also resume PSP IP block under SRIOV.
Signed-off-by: Bokun Zhang <Bokun.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The function amdgpu_fence_count_emitted used in work_hander should not call
amdgpu_fence_process which must be used in irq handler.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jiadong.Zhu <Jiadong.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current position calulated in gfx_v9_0_ring_emit_patch_cond_exec
underflows when the wptr is divisible by ring->buf_mask + 1.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jiadong.Zhu <Jiadong.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For individual feature testing, PMFW may not report all clock
values back. Driver will default them to 0 but this will
cause the BB table to be skipped and default to one state
with max clocks.
[How]
Add helper function to scan through initial clock values and
populate them with default clock limits so that BB table
can be built.
Add dpm_enabled flag to check when DPM is not enabled and
to trigger helper function.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Programming pixel rate divider when FIFO is enabled can cause FIFO error.
[How]
Skip divider programming when divider values are the same to prevent FIFO
error.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Revert "dc: skip audio setup when audio stream is enabled"
This reverts commit 65fbfb02c2
[why]
We have minimal pipe split transition method to avoid pipe
allocation outage.However, this method will invoke audio setup
which cause audio output stuck once pipe reallocate.
[how]
skip audio setup for pipelines which audio stream has been enabled
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We rely on DMCUB to do this when disabling the link but it should
actually come before we disable the DP VID stream.
If we don't then the FIFO can end up with underflow that persists
the next time it's enabled.
[How]
Add a DCN314 specific blank sequence that will disable the DIG FIFO
first.
Reviewed-by: Syed Hassan <Syed.Hassan@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
