rcar_mipi_dsi_startup() writes correct values to VCLKSET, but as it uses
or-operation to add the new values to the current value in the register,
it should first make sure the fields are cleared.
Do this by using rcar_mipi_dsi_write() to write the VCLKSET register
with a variable that has all the unused bits zeroed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The rcar crtc depends on the clock provided from the rcar DSI bridge.
When the DSI bridge is disabled, the clock is stopped, which causes the
crtc disable to timeout.
Also, while I have no issue with the enable, the documentation suggests
to enable the DSI before the crtc so that the crtc has its clock enabled
at enable time. This is also not done by the current driver.
To fix this, we need to keep the DSI bridge enabled until the crtc has
disabled itself, and enable the DSI bridge before crtc enables itself.
Add functions rcar_mipi_dsi_pclk_enable and rcar_mipi_dsi_pclk_disable
to the rcar DSI bridge driver which the rcar driver can use to
enable/disable the DSI clock when needed. This is similar to what is
already done with the rcar LVDS bridge.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The driver does not explicitly stop the video mode transmission when
disabling the output. While this doesn't seem to be causing any issues,
lets follow the steps described in the documentation and add a
rcar_mipi_dsi_stop_video() which stop the video mode transmission. This
function will also be used in later patches to stop the video
transmission even if the DSI IP is not shut down.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The DU driver uses the rcar_lvds_clk_enable() and
rcar_lvds_clk_disable() functions enable or disable the pixel clock
generated by the LVDS encoder, as it requires that clock for proper DU
operation. Rename the functions by replacing "clk" with "pclk" to make
it clearer that they related to the pixel clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Commit 841281fe52 ("drm: rcar-du: Drop LVDS device tree backward
compatibility") has removed device tree overlay sources used for
backward compatibility with old bindings, but forgot to remove related
variables from the Makefile. Fix it.
Fixes: 841281fe52 ("drm: rcar-du: Drop LVDS device tree backward compatibility")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The rcar DU driver on r8a779a0 has a bug causing some specific colors
getting converted to transparent colors, which then (usually) show as
black pixels on the screen.
The reason seems to be that the driver sets PnMR_SPIM_ALP bit in
PnMR.SPIM field, which is an illegal setting on r8a779a0. The
PnMR_SPIM_EOR bit also illegal.
Add a new feature flag for this (lack of a) feature and make sure the
bits are zero on r8a779a0.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
DRM_MODE_BLEND_PIXEL_NONE ignores an alpha channel.
Rcar-du driver supports only 3 formats with an alpha channel
(DRM_FORMAT_ARGB1555, DRM_FORMAT_ARGB8888 and DRM_FORMAT_ARGB4444). We
simply override the format passed to VSP1 for blending with the pixel
format without alpha channel.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
R-Car DU driver implicitly supports DRM_MODE_BLEND_COVERAGE only.
This adds a support for DRM_MODE_BLEND_PREMULTI. As a consequence,
DRM_MODE_BLEND_PREMULTI becomes the default. If DRM_MODE_BLEND_COVERAGE
is desired, it should be set explicitly.
This behavior comes from how DRM blend mode is supported.
drm_plane_create_blend_mode_property() creates the blend mode property
with the default value of DRM_MODE_BLEND_PREMULTI. This default value
cannot be modified from the atomic driver.
Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The field paddr of struct drm_gem_dma_object holds a DMA address, which
might actually be a physical address. However, depending on the platform,
it can also be a bus address or a virtual address managed by an IOMMU.
Hence, rename the field to dma_addr, which is more applicable.
In order to do this renaming the following coccinelle script was used:
```
@@
struct drm_gem_dma_object *gem;
@@
- gem->paddr
+ gem->dma_addr
@@
struct drm_gem_dma_object gem;
@@
- gem.paddr
+ gem.dma_addr
@exists@
typedef dma_addr_t;
symbol paddr;
@@
dma_addr_t paddr;
<...
- paddr
+ dma_addr
...>
@@
symbol paddr;
@@
dma_addr_t
- paddr
+ dma_addr
;
```
This patch is compile-time tested with:
```
make ARCH={x86_64,arm,arm64} allyesconfig
make ARCH={x86_64,arm,arm64} drivers/gpu/drm`
```
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-5-dakr@redhat.com
Rename "GEM CMA" helpers to "GEM DMA" helpers - considering the
hierarchy of APIs (mm/cma -> dma -> gem dma) calling them "GEM
DMA" seems to be more applicable.
Besides that, commit e57924d4ae ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(GEM)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(gem)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
# Rename all 'cma_obj's to 'dma_obj'.
for ff in $(grep -RiHl "cma_obj" $DIRS)
do
sed -i -E "s/cma_obj/dma_obj/g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "GEM CMA", but not "FB CMA".
Also drivers/gpu/drm/Makefile was fixed up manually after renaming
drm_gem_cma_helper.c to drm_gem_dma_helper.c.
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-4-dakr@redhat.com
Rename "FB CMA" helpers to "FB DMA" helpers - considering the hierarchy
of APIs (mm/cma -> dma -> fb dma) calling them "FB DMA" seems to be
more applicable.
Besides that, commit e57924d4ae ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(FB)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(fb)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "FB CMA", but not "GEM CMA".
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-3-dakr@redhat.com
There's no reason to require the primary plane to always be at the
bottom of the stack, as the VSP supports arbitrary ordering of planes,
and the KMS API doesn't have such a requirement either. Lift the
restriction.
As the primary plane can now be positioned arbitrarily, enable control
of its alpha channel as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Tomohito Esaki <etom@igel.co.jp>
As per R-Car-Gen3_Common_OPC_Customer_Notifications_V30.1.pdf,
unexpected image output(such as incorrect colors or planes being
invisible) can happen on the below conditions, as PnALPHAR register
is not initialized by reset.
When alpha blending (PpMRm.PpSPIM=0b101) is performed and:
•two Planes are enabled on any DUn (n=0,1,2,3)
oDSPRn= 0x0000 0031 or 0x0000 0013
•or DU0 and DU1 is used for display at the same time
oDSPR0= 0x0000 0001 and DSPR1= 0x0000 0003
oDSPR0= 0x0000 0003 and DSPR1= 0x0000 0001
•or DU2 and DU3(H3 Only) is used for display at the same time
oDSPR2= 0x0000 0001 and DSPR3= 0x0000 0003
oDSPR2= 0x0000 0003 and DSPR3= 0x0000 0001
This patch set PnALPHAR register to 0 to avoid this issue.
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Clients of drm_writeback_connector_init() initialize the
possible_crtcs and then invoke the call to this API.
To simplify things, allow passing possible_crtcs as a parameter
to drm_writeback_connector_init() and make changes to the
other drm drivers to make them compatible with this change.
changes in v2:
- split the changes according to their functionality
changes in v3:
- allow passing possible_crtcs for existing users of
drm_writeback_connector_init()
- squash the vendor changes into the same commit so
that each patch in the series can compile individually
changes in v4:
- keep only changes related to possible_crtcs
- add line breaks after ARRAY_SIZE
- stop using temporary variables for possible_crtcs
changes in v5:
- None
changes in v6:
- None
changes in v7:
- wrap long lines to match the coding style of existing drivers
- Fix indentation and remove parenthesis where not needed
- use u32 instead of uint32_t for possible_crtcs
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Patchwork: https://patchwork.freedesktop.org/patch/483501/
Link: https://lore.kernel.org/r/1650984096-9964-2-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Improve performance of some fbdev ops, in some cases up to 6x faster.
Core Changes:
- Some small DP fixes.
- Find panels in subnodes of OF devices, and add of_get_drm_panel_display_mode
to retrieve mode.
- Add drm_object_property_get_default_value and use it for resetting
zpos in plane state reset, removing the need for individual drivers
to do it.
- Same for color encoding and color range props.
- Update panic handling todo doc.
- Add todo that format conversion helpers should be sped up similarly to fbdev ops.
Driver Changes:
- Add panel orientation property to simpledrm for quirked panels.
- Assorted small fixes to tiny/repaper, nouveau, stm, omap, ssd130x.
- Add crc support to stm/ltdc.
- Add MIPI DBI compatible SPI driver
- Assorted small fixes to tiny panels and bridge drivers.
- Add AST2600 support to aspeed.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/48fabd78-ade9-f80b-c724-13726c7be69e@linux.intel.com
The rcar-du driver goes to great lengths to preserve device tree
backward compatibility for the LVDS encoders by patching old device
trees at runtime.
The last R-Car Gen2 platform was converted to the new bindings commit
edb0c3affe ("ARM: dts: r8a7793: Convert to new LVDS DT bindings"),
in v4.17, and the last RZ/G1 platform converted in commit
6a6a797625 ("ARM: dts: r8a7743: Convert to new LVDS DT bindings"),
in v5.0. Both are older than commit 58256143cf ("clk: renesas:
Remove R-Car Gen2 legacy DT clock support"), in v5.5, which removes
support for legacy bindings for clocks. The LVDS compatibility code is
thus not needed anymore. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
According to disable Documentation/admin-guide/kernel-parameters.txt, this
parameter can be used to disable kernel modesetting.
DRM drivers will not perform display-mode changes or accelerated rendering
and only the system framebuffer will be available if it was set-up.
But only a few DRM drivers currently check for nomodeset, make this driver
to also support the command line parameter.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211217003752.3946210-32-javierm@redhat.com
On platforms with an external clock, both the group and crtc must be
handled accordingly to correctly pass through the external clock and
configure the DU to use the external rate.
The CRTC support was missed while adding the DSI support on the r8a779a0
which led to the output clocks being incorrectly determined.
Ensure that when a CRTC is routed through the DSI encoder, the external
clock is used without any further divider being applied.
Fixes: b291fdcf51 ("drm: rcar-du: Add r8a779a0 device support")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
When the CMM is enabled, an offset of 25 pixels must be subtracted from
the HDS (horizontal display start) and HDE (horizontal display end)
registers. Fix the timings calculation, and take this into account in
the mode validation.
This fixes a visible horizontal offset in the image with VGA monitors.
HDMI monitors seem to be generally more tolerant to incorrect timings,
but may be affected too.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The meaning of the 'imply' keyword has changed recently, and neither the
old meaning (select the symbol if its dependencies are met) nor the new
meaning (enable it by default, but let the user set any other setting)
is what we want here.
Work around this by adding two more Kconfig options that lead to
the correct behavior: if DRM_RCAR_USE_CMM and DRM_RCAR_USE_LVDS
are enabled, that portion of the driver becomes usable, and no
configuration results in a link error.
This avoids a link failure:
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_crtc.o: in function `rcar_du_crtc_atomic_begin':
rcar_du_crtc.c:(.text+0x1444): undefined reference to `rcar_cmm_setup'
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_crtc.o: in function `rcar_du_crtc_atomic_enable':
rcar_du_crtc.c:(.text+0x14d4): undefined reference to `rcar_cmm_enable'
arm-linux-gnueabi-ld: rcar_du_crtc.c:(.text+0x1548): undefined reference to `rcar_cmm_setup'
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_crtc.o: in function `rcar_du_crtc_atomic_disable':
rcar_du_crtc.c:(.text+0x18b8): undefined reference to `rcar_cmm_disable'
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_kms.o: in function `rcar_du_modeset_init':
Link: https://lore.kernel.org/all/20200417155553.675905-5-arnd@arndb.de/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link drm_fb_cma_helper.o into drm_cma_helper.ko if CONFIG_DRM_KMS_HELPER
has been set. Remove CONFIG_DRM_KMS_CMA_HELPER config option. Selecting
KMS helpers and CMA will now automatically enable CMA KMS helpers.
Some drivers' Kconfig files did not correctly select KMS or CMA helpers.
Fix this as part of the change.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211106193509.17472-3-tzimmermann@suse.de
