Non-continuous clock mode doesn't work because driver doesn't support it
properly. The bridge driver programs wrong bitfields that are required by
the non-continuous mode (BTACNTRL1 register bitfields are swapped in the
code), but fixing them doesn't help.
Display panel of ASUS Transformer TF700T tablet supports non-continuous
mode and display doesn't work at all using that mode. There are no
device-trees that are actively using this DSI bridge in upstream yet,
so clearly the broken mode wasn't ever tested properly. It's a bit too
difficult to get LP mode working, hence let's disable the offending mode
for now and fall back to continuous mode.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> #TF700T
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211002233447.1105-5-digetx@gmail.com
Current code always sets reset line low in .pre_enable callback and
holds it low for 10ms. This is sub-optimal and increases the time
between enablement of the DSI83 and valid LVDS clock.
Rework the reset handling such that the reset line is held low for 10ms
both in probe() of the driver and .disable callback, which guarantees
that the reset line was always held low for more than 10ms and therefore
the reset line timing requirement is satisfied. Furthermore, move the
reset handling into .enable callback so the entire DSI83 initialization
is now in one place.
This reduces DSI83 enablement delay by up to 10ms.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211016210402.171595-1-marex@denx.de
Components further up in the chain might ask us for supported formats.
Without this MEDIA_BUS_FMT_FIXED is assumed which then breaks display
output with mxsfb since it can't determine a proper bus format.
We handle the bus formats that correspond to the DSI formats the bridge
can potentially output (see chapter 13.6 of the i.MX 8MQ reference
manual) - which matches what xsfb can input.
Fixes: b776b0f00f ("drm: mxsfb: Use bus_format from the nearest bridge if present")
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1712f2b952694fd4484dfd8576fbc5b4d7adf042.1633959458.git.agx@sigxcpu.org
By depending on devm_drm_panel_bridge_add(), devm_drm_of_get_bridge()
introduces a circular dependency between the modules drm (where
devm_drm_of_get_bridge() ends up) and drm_kms_helper (where
devm_drm_panel_bridge_add() is).
Fix this by moving devm_drm_of_get_bridge() to bridge/panel.c and thus
drm_kms_helper.
Fixes: 87ea95808d ("drm/bridge: Add a function to abstract away panels")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210917180925.2602266-1-maxime@cerno.tech
Currently it66121_probe returns -EPROBE_DEFER if the there is no remote
endpoint found in the device tree which doesn't seem helpful, since this
is not going to change later and it is never checked if the next bridge
has been initialized yet. It will fail in that case later while doing
drm_bridge_attach for the next bridge in it66121_bridge_attach.
Since the bindings documentation for it66121 bridge driver states
there has to be a remote endpoint defined, its safe to return -EINVAL
in that case.
This additonally adds a check, if the remote endpoint is enabled and
returns -EPROBE_DEFER, if the remote bridge hasn't been initialized
(yet).
Fixes: 988156dc2f ("drm: bridge: add it66121 driver")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210918140420.231346-1-knaerzche@gmail.com
These two arrays are populated with data read from the I2C device
through regmap_read(), and the data is then compared with hardcoded
vendor/product ID values of supported chips.
However, the return value of regmap_read() was never checked. This is
fine, as long as the two arrays are zero-initialized, so that we don't
compare the vendor/product IDs against whatever garbage is left on the
stack.
Address this issue by zero-initializing these two arrays.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 988156dc2f ("drm: bridge: add it66121 driver")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827163956.27517-1-paul@crapouillou.net
When testing with a panel that's apparently a little more persnickety
about the correct power sequence (specifically Samsung ATNA33XC20), we
found that the ti-sn65dsi86 was doing things just slightly wrong.
Looking closely at the ti-sn65dsi86's datasheet, the power off
sequence is supposed to be:
1. Clear VSTREAM_ENABLE bit
2. Stop DSI stream from GPU. DSI lanes must be placed in LP11 state.
3. Program the ML_TX_MODE to 0x0 (OFF)
4. Program the DP_NUM_LANES register to 0x0
5. Clear the DP_PLL_EN bit.
6. Deassert the EN pin.
7. Remove power from supply pins
Since we were doing the whole sequence in the "disable", I believe
that step #2 (stopping the DSI stream from the GPU) wasn't
happening. We also weren't setting DP_NUM_LANES to 0.
Let's fix this.
NOTE: things are a little asymmetric now. For instance, we turn the
PLL on in "enable" but now we're not turning it off until
"post_disable". It would seem to make sense to move the PLL turning on
to "pre_enable" to match. Unfortunately, I don't believe that's
allowed. It looks as if (in the non-refclk mode which probably nobody
is using) we have to wait until the MIPI clock is there before we can
enable the PLL. In any case, the way it is here won't really
hurt--it'll just leave the PLL on a little longer.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730084534.v2.2.If8a8ec3bf1855cf0dbb62c005a71d6698c99c125@changeid
drm-misc-next for v5.15:
UAPI Changes:
- Add modifiers for arm fixed rate compression.
Cross-subsystem Changes:
- Assorted dt binding fixes.
- Convert ssd1307fb to json-schema.
- Update a lot of irc channels to point to OFTC, as everyone moved there.
- Fix the same divide by zero for asilantfb, kyro, rivafb.
Core Changes:
- Document requirements for new atomic properties.
- Add drm_gem_fb_(begin/end)_cpu_access helpers, and use them in some drivers.
- Document drm_property_enum.value for bitfields.
- Add explicit _NO_ for MIPI_DSI flags that disable features.
- Assorted documentation fixes.
- Update fb_damage handling, and move drm_plane_enable_fb_damage_clips to core.
- Add logging and docs to RMFB ioctl.
- Assorted small fixes to dp_mst, master handling.
- Clarify drm lease usage.
Driver Changes:
- Assorted small fixes to panfrost, hibmc, bridge/nwl-dsi, rockchip, vc4.
- More drm -> linux irq conversions.
- Add support for some Logic Technologies and Multi-Inno panels.
- Expose phy-functionality for drm/rockchip, to allow controlling from the media subsystem.
- Add support for 2 AUO panels.
- Add damage handling to ssd1307fb.
- Improve FIFO handling on mxsfb.
- Assorted small fixes to vmwgfx, and bump version to 2.19 for the new ioctls.
- Improve sony acx424akp backlight handling.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a753221a-e23e-0dc4-7ca6-8c1b179738d0@linux.intel.com
On all platforms except i.MX and Rockchip, the dw-hdmi DT bindings
require a video output port connected to an HDMI sink (most likely an
HDMI connector, in rare cases another bridges converting HDMI to another
protocol). For those platforms, retrieve the next bridge and attach it
from the dw-hdmi bridge attach handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Don't populate the const array frs_limits on the stack but instead make
it static. Makes the object code smaller by 128 bytes:
Before:
text data bss dec hex filename
24845 7440 64 32349 7e5d ./drivers/gpu/drm/bridge/tc358768.o
After:
text data bss dec hex filename
24749 7408 64 32221 7ddd ./drivers/gpu/drm/bridge/tc358768.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Finding panel_or_bridge might vary based on associated
DSI devices like DSI panel, bridge, and I2C based DSI
bridge.
1. DSI panels and bridges will invoke the host attach
from probe in order to find the panel_or_bridge.
chipone_probe()
dw_mipi_dsi_host_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_host_attach().start
chipone_attach(). start
chipone_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
2. I2C based DSI bridge will invoke the drm_bridge_attach
from bridge attach in order to find the panel_or_bridge.
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
dw_mipi_dsi_host_attach().start
sn65dsi83_attach(). start
sn65dsi83_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
So, invoke the panel_or_bridge from host attach and
bridge attach in order to find all possible DSI devices.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210704140309.268469-1-jagan@amarulasolutions.com
