On the SII9022, the IOVCC and CVCC12 supplies must reach the correct
voltage before the reset sequence is initiated. On most boards, this
assumption is true at boot-up, so initialization succeeds.
However, when we try to initialize the chip with incorrect supply
voltages, it will not respond to I2C requests. sii902x_probe() fails
with -ENXIO.
To resolve this, look for the "iovcc" and "cvcc12" regulators, and
make sure they are enabled before starting the reset sequence. If
these supplies are not available in devicetree, then they will default
to dummy-regulator. In that case everything will work like before.
This was observed on a STM32MP157C-DK2 booting in u-boot falcon mode.
On this board, the supplies would be set by the second stage
bootloader, which does not run in falcon mode.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
[Fix checkpatch warnings]
Link: https://patchwork.freedesktop.org/patch/msgid/20201020221501.260025-2-mr.nuke.me@gmail.com
We should be setting the drm_dp_aux_msg::reply field if a NACK or a
SHORT reply happens. Update the error bit handling logic in
ti_sn_aux_transfer() to handle these cases and notify upper layers that
such errors have happened. This helps the retry logic understand that a
timeout has happened, or to shorten the read length if the panel isn't
able to handle the longest read possible.
Note: I don't have any hardware that exhibits these code paths so this
is written based on reading the datasheet for this bridge and inspecting
the code and how this is called.
Changes in v2:
- Move WRITE_STATUS_UPDATE check from case to assignment
Changes in v2:
- Handle WRITE_STATUS_UPDATE properly
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Sean Paul <seanpaul@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201102181144.3469197-5-swboyd@chromium.org
On some panels hooked up to the ti-sn65dsi86 bridge chip we found that
link training was failing. Specifically, we'd see:
ti_sn65dsi86 2-002d: [drm:ti_sn_bridge_enable] *ERROR* Link training failed, link is off (-5)
The panel was hooked up to a logic analyzer and it was found that, as
part of link training, the bridge chip was writing a 0x1 to DPCD
address 00600h and the panel responded NACK. As can be seen in header
files, the write of 0x1 to DPCD address 0x600h means we were trying to
write the value DP_SET_POWER_D0 to the register DP_SET_POWER. The
panel vendor says that a NACK in this case is not unexpected and means
"not ready, try again".
In testing, we found that this panel would respond with a NACK in
about 1/25 times. Adding the retry logic worked fine and the most
number of tries needed was 3. Just to be safe, we'll add 10 tries
here and we'll add a little blurb to the logs if we ever need more
than 5.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002135920.1.I2adbc90b2db127763e2444bd5a4e5bf30e1db8e5@changeid
This patch restores DRM connector registration in the TC358764 bridge
driver and restores usage of the old drm_panel_* API, thus allows dynamic
panel registration. This fixes panel operation on Exynos5250-based
Arndale board.
This is equivalent to the revert of the following commits:
1644127f83 "drm/bridge: tc358764: add drm_panel_bridge support"
385ca38da2 "drm/bridge: tc358764: drop drm_connector_(un)register"
and removal of the calls to drm_panel_attach()/drm_panel_detach(), which
were no-ops and has been removed in meanwhile.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200930114042.5806-1-m.szyprowski@samsung.com
drm-misc-next for 5.10:
UAPI Changes:
Cross-subsystem Changes:
- virtio: Merged a PR for patches that will affect drm/virtio
Core Changes:
- dev: More devm_drm convertions and removal of drm_dev_init
- atomic: Split out drm_atomic_helper_calc_timestamping_constants of
drm_atomic_helper_update_legacy_modeset_state
- ttm: More rework
Driver Changes:
- i915: selftests improvements
- panfrost: support for Amlogic SoC
- vc4: one fix
- tree-wide: conversions to devm_drm_dev_alloc,
- ast: simplifications of the atomic modesetting code
- panfrost: multiple fixes
- vc4: multiple fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921152956.2gxnsdgxmwhvjyut@gilmour.lan
Add a new DRM bridge driver for Cadence MHDP8546 DPTX IP used in TI J721E
SoC. MHDP DPTX IP is the component that complies with VESA DisplayPort (DP)
and embedded Display Port (eDP) standards. It integrates uCPU running the
embedded Firmware (FW) interfaced over APB interface.
Basically, it takes a DPI stream as input and outputs it encoded in DP
format. Currently, it supports only SST mode.
Co-developed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Co-developed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The get_edid() callback can be triggered anytime by an ioctl, i.e
drm_mode_getconnector (ioctl)
-> drm_helper_probe_single_connector_modes
-> drm_bridge_connector_get_modes
-> ps8640_bridge_get_edid
Actually if the bridge pre_enable() function was not called before
get_edid(), the driver will not be able to get the EDID properly and
display will not work until a second get_edid() call is issued and if
pre_enable() is called before. The side effect of this, for example, is
that you see anything when `Frecon` starts, neither the splash screen,
until the graphical session manager starts.
To fix this we need to make sure that all we need is enabled before
reading the EDID. This means the following:
1. If get_edid() is called before having the device powered we need to
power on the device. In such case, the driver will power off again the
device.
2. If get_edid() is called after having the device powered, all should
just work. We added a powered flag in order to avoid recurrent calls
to ps8640_bridge_poweron() and unneeded delays.
3. This seems to be specific for this device, but we need to make sure
the panel is powered on before do a power on cycle on this device.
Otherwise the device fails to retrieve the EDID.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Bilal Wasim <bwasim.lkml@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200827085911.944899-2-enric.balletbo@collabora.com
Backmerging drm-next into drm-misc-next for nouveau and panel updates.
Resolves a conflict between ttm and nouveau, where struct ttm_mem_res got
renamed to struct ttm_resource.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
This driver is tested with two panels individually with Apq8016-IFC6309 board
https://www.inforcecomputing.com/products/single-board-computers-sbc/qualcomm-snapdragon-410-inforce-6309-micro-sbc
1. 1366x768@60 auo,b101xtn01 data-mapping = "jeida-24"
2. 800x480@60 innolux,at070tn92 data-mapping = "vesa-24"
- power off sequence in proper order
- put_unaligned_be16, put_unaligned_le32 macros used
- static function for mode_valid
- len initialized
- MODE_CLOCK_HIGH handled properly
- bus_formats handled in mode_valid
- GENMASK and FIELD_PREP used
- Kconfig proper indentation
- error handling endpoint data-lanes
- check for bus_formats unsupported
- display_timings naming local variables
- help modified
- ~vsdelay dynamic value set based on the
calculation of dsi speed, output speed, blanking
- panel->connector_type removed
- dual port implemented
- devm_drm_panel_bridge_add method used instead of panel
description modified
- regulator enable and disable with proper orders and delays
as per the spec
- removed drm_connector_status
- added bus_formats
- mdelay to usleep_range
- magic number to macros for CLRSI and mux registers
description modified
- replaced u32 instead of uint32_t
- updated alphabetic order of headers
- added SPDX identifier license
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam.ravnborg@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1594388491-15129-2-git-send-email-simhavcs@gmail.com
