Revert "dc: skip audio setup when audio stream is enabled"
This reverts commit 65fbfb02c2
[why]
We have minimal pipe split transition method to avoid pipe
allocation outage.However, this method will invoke audio setup
which cause audio output stuck once pipe reallocate.
[how]
skip audio setup for pipelines which audio stream has been enabled
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We rely on DMCUB to do this when disabling the link but it should
actually come before we disable the DP VID stream.
If we don't then the FIFO can end up with underflow that persists
the next time it's enabled.
[How]
Add a DCN314 specific blank sequence that will disable the DIG FIFO
first.
Reviewed-by: Syed Hassan <Syed.Hassan@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DIO FIFO will underflow if we turn off the OTG before we turn
off the FIFO.
Since this happens as part of the OTG workaround and we don't reset
the FIFO afterwards we see the error persist.
[How]
Add disable FIFO before the disable CRTC and enable FIFO after enabling
the CRTC.
Reviewed-by: Syed Hassan <Syed.Hassan@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Partially valid EDIDs on MST sinks are treated the same way as broken
EDIDs or read failures and result in a fallback EDID being used instead.
[How]
If edid_status is EDID_PARTIAL_VALID, prefer to use the valid EDID
blocks instead of using a fallback EDID.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Avoids a race condition where DIO FIFO can underflow due to no incoming
data available.
[How]
Shift the FIFO enable below stream enable.
Make sure fullness level is written before the DIO reset takes place
and that we're not doing it twice.
Reviewed-by: Syed Hassan <Syed.Hassan@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Only a single VLINE interrupt is available so interface should not
expose the second one which is used by DMU firmware.
[how]
Remove references to periodic_interrupt1 and VLINE1 from DC interfaces.
Reviewed-by: Jaehyun Chung <jaehyun.chung@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Most of the arguments are identical between the two call sites and they
can be accessed through the 'struct vba_vars_st' pointer. This reduces
the total amount of stack space that
dml314_ModeSupportAndSystemConfigurationFull() uses by 112 bytes with
LLVM 16 (1976 -> 1864), helping clear up the following clang warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn314/display_mode_vba_314.c:4020:6: error: stack frame size (2216) exceeds limit (2048) in 'dml314_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
void dml314_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
^
1 error generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/1710
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Tested-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Most of the arguments are identical between the two call sites and they
can be accessed through the 'struct vba_vars_st' pointer. This reduces
the total amount of stack space that
dml314_ModeSupportAndSystemConfigurationFull() uses by 240 bytes with
LLVM 16 (2216 -> 1976), helping clear up the following clang warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn314/display_mode_vba_314.c:4020:6: error: stack frame size (2216) exceeds limit (2048) in 'dml314_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
void dml314_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
^
1 error generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/1710
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Tested-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This shouldn't trigger during tiled display hotplug/unplug but it does
because one of the tiles can end up with a NULL plane state.
This also doesn't guard against the hang that it was originally trying
to resolve, and can instead cause DIO corruption due to OTG sync
being lost.
[How]
This was reverted at one point out of DCN31 so revert it here too.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When USB4 DP link training failed and fell back to lower link rate,
the time slot calculation uses the verified_link_cap.
And the verified_link_cap was not updated to the new one.
It caused the wrong VC payload time-slot was allocated.
[How]
Updated verified_link_cap with the new one from cur_link_settings
after the LT completes successfully.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During hot plug of specific 5K tiled display, sometimes both the tiles
are not synchronized resulting in distortion. The reason is that otgs of
both the tiles goes out of sync when otg workaround (dcnxxx_disable_otg_wa)
is applied for bandwidth optimization. The otg workaround reenables otg
but otg synchronization context is not reset and hence dc_trigger_sync()
does not resynchronize otg again.
[How]
Implement reset_sync_context_for_pipe() to reset the otg synchronization
context for the disabled pipe and its slave pipes when otg workaround is
applied.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current DCN3.2 logic for finding the dummy P-state index uses the
DCN3.0 DML validation function instead of DCN3.2 DML.
This can result in either unexpected DML VBA values, or unexpected
dummy P-state index to be used.
[How]
Update the dummy P-state logic to use DCN3.2 DML validation function.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We have minimal pipe split transition method to avoid pipe
allocation outage.However, this method will invoke audio setup
which cause audio output stuck once pipe reallocate.
[how]
skip audio setup for pipelines which audio stream has been enabled
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: zhikzhai <zhikai.zhai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The desktop plane and full-screen game plane may have different
gamut remap coefficients, if switching between desktop and
full-screen game without updating the gamut remap will cause
incorrect color.
[How]
Update gamut remap if planes change.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
LTTPRs can in very rare instsances fail to increment DPCD LTTPR count.
This results in aux-i LTTPR requests to be sent to the wrong DPCD
address, which causes link training failure.
[HOW]
Override internal repeater count if fixed_vs flag is set for a given link
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC makes use of layer_index (zpos) when picking the HW plane to enable
HW cursor on. However, some compositors will not attach zpos information
to each DRM plane. Consequently, in amdgpu, we default layer_index to 0
and do not update it.
This causes said DC logic to enable HW cursor on all planes of the same
layer_index, which manifests as a double cursor issue if one of the
planes is scaled (and hence scaling the cursor as well).
[How]
Use DRM core helpers to calculate a normalized_zpos value for each
drm_plane_state under each crtc, within the atomic state.
This helper will first consider existing zpos values, and if
identical/unset, fallback to plane ID ordering.
The normalized_zpos is then passed to dc_plane_info during atomic check
for later use by the cursor logic.
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
420 modes are limited by FMT buffer width of 4096
which requires multi-pipe support in form of ODM
combine. If 420 modes have greater HActive than
4096, the DML logic should accomodate whether
it should be rejected, or ODM combine 2:1 or 4:1
is triggered accordingly.
[How]
FMT Buffer limit of 4096 in DCN32. Force ODM
combine depending on HActive and FMT Buffer limit.
Reject modes if TMDS 420 and above 4096.
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Most of the arguments are identical between the two call sites and they
can be accessed through the 'struct vba_vars_st' pointer. This reduces
the total amount of stack space that
dml314_ModeSupportAndSystemConfigurationFull() uses by 112 bytes with
LLVM 16 (1976 -> 1864), helping clear up the following clang warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn314/display_mode_vba_314.c:4020:6: error: stack frame size (2216) exceeds limit (2048) in 'dml314_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
void dml314_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
^
1 error generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/1710
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Tested-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Most of the arguments are identical between the two call sites and they
can be accessed through the 'struct vba_vars_st' pointer. This reduces
the total amount of stack space that
dml314_ModeSupportAndSystemConfigurationFull() uses by 240 bytes with
LLVM 16 (2216 -> 1976), helping clear up the following clang warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn314/display_mode_vba_314.c:4020:6: error: stack frame size (2216) exceeds limit (2048) in 'dml314_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
void dml314_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
^
1 error generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/1710
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Tested-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fix urgent latency override for DCN32/DCN321
- Correct hostvm flag in DCN31
- Added new Asic Id for DCN301
- Adjust to 2 phys in DCN301
- Update dummy P-state search to use DCN32 DML
- Increase dcn315 pstate change latency
- Disable OTG WA for the plane_state NULL case on DCN314
- Update dccg based on HW delta
- Correct num_dsc for DCN314
- Fix DP DSC compliance failure with DCN314
- Refactor edp power sequencer codes
- update gamut remap if plane has changed
- Skip audio setup when audio stream is enabled
- Display distortion after hotplug LG Ultrafine 5K tiled display
- Fix DP MST timeslot issue when fallback happened
- Uncomment SubVP pipe split assignment in driver
- Enable committing subvp config
- Do second pass through DML for DET calculation
- Don't allocate DET for phantom pipes
- Modify DML to adjust Vstartup Position
- Ignore k1/k2 values for virtual signal to avoid assert
- Fix failures of disabling primary planes
- Do not compare integers of different widths
- Fix empty slot problem of EDID management
- Revise Sink device string ID width in dmub psr
- Log vertical interrupt 1 for debug
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a coding error when moving dp disable link phy to
hw sequencer, where the receiver power control is missed during
this refactor.
[how]
1. Add back missing receiver power control in disable link phy.
2. minor modifications to ensure there is no undesired sequence
changes in dp link enable/disable.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The Vstartup position should be as late as possible to
maximize power saving with the current. Calculation of
Vstartup in DML does not take into account as SDP signal.
[HOW]
Made necessary changes to calculate the correct Vstartup
position in DML to account for AS SDP
* Overriding the VBlankNom value in certain cases
otherwise it will use the default value
* Bypassing the condition for adjust_sync_Vstartup
* Overriding vblank_nom_input with VBlankNom that is
set in the SW Layer
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: muansari <muansari@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This shouldn't trigger during tiled display hotplug/unplug but it does
because one of the tiles can end up with a NULL plane state.
This also doesn't guard against the hang that it was originally trying
to resolve, and can instead cause DIO corruption due to OTG sync
being lost.
[How]
This was reverted at one point out of DCN31 so revert it here too.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
v1_5 display object table has no way for connectors to
indicate which slot they are a part of, resulting in additional
empty slots to appear in EDID management UI.
[How]
Assume that all connectors belong to the same slot.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and How]
We are hitting k1/k2 assert when we are using a virtual signal in the
test; as a result, we are failing some automated tests with a false
positive. This commit addresses this issue by ignoring the assert
condition if we use SIGNAL_TYPE_VIRTUAL.
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When USB4 DP link training failed and fell back to lower link rate,
the time slot calculation uses the verified_link_cap.
And the verified_link_cap was not updated to the new one.
It caused the wrong VC payload time-slot was allocated.
[How]
Updated verified_link_cap with the new one from cur_link_settings
after the LT completes successfully.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
