[Why]
When waking from low-power states, a DP sink may remain unresponsive to
AUX transactions.
[How]
Try to toggle DPCD SET_POWER register repeatedly (up to a maximum
timeout value) until DP sink becomes responsive.
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In init_hw() we call init_pipes() before enabling power gating.
init_pipes() tries to power gate dsc but it may fail because
required force-ons are not released yet.
As a result with dsc config the following errors observed on resume:
"REG_WAIT timeout 1us * 1000 tries - dcn20_dsc_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_dpp_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_hubp_pg_control"
[How]
Move enable_power_gating_plane() before init_pipes() in init_hw()
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC Power down code has been moved from dcn31_init_hw into init_pipes()
Need to remove it from dcn10_init_hw() as well to avoid duplicated action
on dcn1.x/2.x
[How]
Remove DSC power down code from dcn10_init_hw()
Fixes: 8fa6f4c571 ("drm/amd/display: fixed the DSC power off sequence during Driver PnP")
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Once DSC slice cannot fit pixel clock, we incorrectly
reset min slices to 0 and allow max slice to operate,
even when max slice itself cannot fit the pixel clock
properly.
[How]
Change the sequence such that we correctly determine
DSC is not possible when both min slices and max
slices cannot fit pixel clock per slice.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Make dcn315 base its clock table off dcfclk rather than fclk.
This change also adds some sanity checking to make sure an
empty pmfw table does not result in invalid dal clocks.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- [FW Promotion] Release 0.0.111.0
- Check for invalid input params when building scaling params
- Move link_trace for edp to dp_trace
- Fix missing-prototypes warning
- Enable 3 plane for DCN 3.0 and 3.02
- Extract set stream attribute into link_hwss
- Revert Power down hardware if timer not trigger
- Add support for handling 128b/132b link training test request
- Add configuration options for AUX wake work around
- Remove underflow IRQ type
- Add flip interval workaround for low FPS in some game
- Remove assert for odm transition case
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP2.x added new enum values for UHBR link rates in link training test
request for test automation. We need to add UHBR link rates test request
support in preparation for compliance test automation.
[how]
added a function that translate test link rate to dc link rate. Call
the translation function to decide the requested test link rate.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Work around to try to wake unresponsive DP sinks may need to be adjusted
for certain sinks.
[How]
Add options to disable work around or adjust time spent trying to wake
unresponsive DPRX.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some games experience low FPS issues when FreeSync is on and VSync is
toggled to half refresh rate.
[HOW]
First create a function to determine workaround conditions, which is
when we detect 2 or more VSync interrupts between flips and a very short
VSync to flip interval. We do the workaround during VSync interrupts and
set the v_total_max and min to nominal. We also cleanup after we exit
the game.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Angus Wang <Angus.Wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the kernel test robot warning below:
drivers/gpu/drm/amd/amdgpu/../display/dmub/inc/dmub_cmd.h:2893:12:
warning: variable 'temp' set but not used [-Wunused-but-set-variable]
Replaced the assignment to the unused temp variable with READ_ONCE()
macro to flush the writes. READ_ONCE() helps avoid the use of
volatile and makes it obvious from the code that the read here is
intentional. Also verified on x86 that the generated code is exactly the
same as before.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Aashish Sharma <shraash@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
FPU documentation states that developers must not use DC_FP_START/END
inside dml files, but use this macro to wrap calls to FPU functions in
dc folder (outside dml folder). Therefore, this patch removes DC_FP_*
wrappers from dml folder and wraps calls for these FPU operations
outside dml, as required.
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn10_validate_bandwidth is only used on dcn10 files, but is declared in
dcn_calcs files. Rename dcn10_* to dcn_* in calcs, remove DC_FP_* wrapper
inside DML folder and create an specific dcn10_validate_bandwidth in
dcn10_resources that calls dcn_validate_bandwidth and properly wraps that
FPU function with DC_FP_* macro.
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
comparing pwm bl values (coverted) with user brightness(converted)
levels in commit_tail leads to continuous setting of backlight via dmub
as they don't to match.
This leads overdrive in queuing of commands to DMCU that sometimes lead
to depending on load on DMCU fw:
"[drm:dc_dmub_srv_wait_idle] *ERROR* Error waiting for DMUB idle: status=3"
[How]
Store last successfully set backlight value and compare with it instead
of pwm reads which is not what we should compare with.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The value actual_pix_clk_100Hz is dereferencing pointer pix_clk_params
before pix_clk_params is being null checked. Fix this by assigning
pix_clk_params->requested_pix_clk_100hz to actual_pix_clk_100Hz only if
pix_clk_params is not NULL, otherwise just NULL.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The pointer edid_buf is dereferencing pointer edid before edid is being
null checked. Fix this by assigning edid->raw_edid to edid_buf only if
edid is not NULL, otherwise just NULL.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume we do link detection for all non-MST connectors.
MST is handled separately. However the condition for telling
if connector is on mst branch is not enough for mst hub case.
Link detection for mst branch link leads to mst topology reset.
That causes assert in dc_link_allocate_mst_payload()
[How]
Use link type as indicator for mst link.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- [FW Promotion] Release 0.0.110.0
- Revert FEC check in validation
- Update LTTPR UHBR link rate support struct
- Add support for USBC connector
- Add work around for AUX failure on wake
- Clear optc false state when disable otg
- Enable power gating before init_pipes
- Remove redundant dsc power gating from init_hw
- Power down hardware if timer not trigger
- Correct Slice reset calculation
- Enable 3-plane MPO for DCN31
- Set fec register init value
- Remove SW w/a for HDCP 1.4 1A-07 failure based on ECO fix
- Create underflow interrupt IRQ type
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When waking from low-power states, a DP sink may remain unresponsive to
AUX transactions.
[How]
Try to toggle DPCD SET_POWER register repeatedly (up to a maximum
timeout value) until DP sink becomes responsive.
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In init_hw() we call init_pipes() before enabling power gating.
init_pipes() tries to power gate dsc but it may fail because
required force-ons are not released yet.
As a result with dsc config the following errors observed on resume:
"REG_WAIT timeout 1us * 1000 tries - dcn20_dsc_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_dpp_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_hubp_pg_control"
[How]
Move enable_power_gating_plane() before init_pipes() in init_hw()
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC Power down code has been moved from dcn31_init_hw into init_pipes()
Need to remove it from dcn10_init_hw() as well to avoid duplicated action
on dcn1.x/2.x
[How]
Remove DSC power down code from dcn10_init_hw()
Fixes: 8fa6f4c571 ("drm/amd/display: fixed the DSC power off sequence during Driver PnP")
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless systems, if SetMode/Power down timer
is not called, hardware will not be powered down
causing HW/SW discrepancies. Powering down hardware
on SetPowerState to D3 will ensure SW/HW state is accurate.
[HOW]
If PowerDownThread timer is not trigger but OS call
SetPowerState to D3, power down hardware.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Once DSC slice cannot fit pixel clock, we incorrectly
reset min slices to 0 and allow max slice to operate,
even when max slice itself cannot fit the pixel clock
properly.
[How]
Change the sequence such that we correctly determine
DSC is not possible when both min slices and max
slices cannot fit pixel clock per slice.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ATOMIC and DRIVER log categories do not typically contain per-frame log
messages. This patch re-classifies some messages in amd to chattier
categories to keep ATOMIC/DRIVER quiet.
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Moves FPU-related structs and dcn316_update_bw_bounding_box from dcn316
driver to dml/dcn31 that centralize FPU operations for DCN 3.1x
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Moves related structs and dcn315_update_bw_bounding_box from dcn315
driver code to dml/dcn31_fpu that centralizes FPU code for DCN 3.1x.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Creates FPU files in dml/dcn31 folder to centralize FPU operations
from 3.1x drivers and moves all FPU-associated code from dcn31 driver
to there. It includes the struct _vcs_dpi_ip_params_st and
_vcs_dpi_soc_bounding_box_st and functions:
- dcn31_calculate_wm_and_dlg_fp()
- dcn31_update_bw_bounding_box()
adding dc_assert_fp_enabled to them and drop DC_FP_START/END inside
functions that was moved to dml folder, as required.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- HDCP SEND AKI INIT error
- fix audio format not updated after edid updated
- Reduce stack size
- FEC check in timing validation
- Add fSMC_MSG_SetDtbClk support
- Update VTEM Infopacket definition
- [FW Promotion] Release 0.0.109.0
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
