The prandom_bytes() function has been a deprecated inline wrapper around
get_random_bytes() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. This was done as a basic find and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> # powerpc
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
If the DMA consumer driver does not expect the callback for TX done, then
we need not perform the channel RT byte counter calculations and estimate
the completion but return complete on first attempt itself.This assumes
that the consumer who did not request DMA_PREP_INTERRUPT has its own
mechanism for understanding TX completion, example: MCSPI EOW interrupt
can be used as TX completion signal for a SPI transaction.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20220914110049.5842-1-vaishnav.a@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dmaengine_synchronize implementation is required to synchronize proper
termination of current transfers so that any memory resources are not freed
while still in use.
Implement this callback in the driver so that framework can use the same
(in dmaengine_terminate_sync/ dmaengine_synchronize).
Signed-off-by: Swati Agarwal <swati.agarwal@amd.com>
Link: https://lore.kernel.org/r/20220915090516.5812-1-swati.agarwal@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, the dw-edma driver enables the runtime_pm for parent device
(chip->dev) and increments/decrements the refcount during alloc/free
chan resources callbacks.
This leads to a problem when the eDMA driver has been probed, but the
channels were not used. This scenario can happen when the DW PCIe driver
probes eDMA driver successfully, but the PCI EPF driver decides not to
use eDMA channels and use iATU instead for PCI transfers.
In this case, the underlying device would be runtime suspended due to
pm_runtime_enable() in dw_edma_probe() and the PCI EPF driver would have
no knowledge of it.
Ideally, the eDMA driver should not be the one doing the runtime PM of
the parent device. The responsibility should instead belong to the client
drivers like PCI EPF.
So let's remove the runtime PM support from eDMA driver.
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20220910054700.12205-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DSA 2.0 add the capability of configuring DMA ops on a per workqueue basis.
This means that certain ops can be disabled by the system administrator for
certain wq. By default, all ops are available. A bitmap is used to store
the ops due to total op size of 256 bits and it is more convenient to use a
range list to specify which bits are enabled.
One of the usage to support this is for VM migration between different
iteration of devices. The newer ops are disabled in order to allow guest to
migrate to a host that only support older ops. Another usage is to
restrict the WQ to certain operations for QoS of performance.
A sysfs of ops_config attribute is added per wq. It is only usable when the
ops_config bit is set under WQ_CAP register. This means that this attribute
will return -EOPNOTSUPP on DSA 1.x devices. The expected input is a range
list for the bits per operation the WQ supports.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220917161222.2835172-4-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To make input and output consistent and prepping for the per WQ operation
configuration support, change the output of opcap display to match the
input that is expected by bitmap_parse() helper function. The output will
be a bitmap with field width as the number of bits using the %*pb format
specifier for printk() family.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220917161222.2835172-3-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
User reports observing timer event report channel halted but no error
observed in CHANERR register. The driver finished self-test and released
channel resources. Debug shows that __cleanup() can call
mod_timer() after the timer has been deleted and thus resurrect the
timer. While harmless, it causes suprious error message to be emitted.
Use mod_timer_pending() call to prevent deleted timer from being
resurrected.
Fixes: 3372de5813 ("dmaengine: ioatdma: removal of dma_v3.c and relevant ioat3 references")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/166360672197.3851724.17040290563764838369.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The calling convention for pre_slave_sg is to return NULL on error and
provide an error log to the system. Qcom-adm instead provide error
pointer when an error occur. This indirectly cause kernel panic for
example for the nandc driver that checks only if the pointer returned by
device_prep_slave_sg is not NULL. Returning an error pointer makes nandc
think the device_prep_slave_sg function correctly completed and makes
the kernel panics later in the code.
While nandc is the one that makes the kernel crash, it was pointed out
that the real problem is qcom-adm not following calling convention for
that function.
To fix this, drop returning error pointer and return NULL with an error
log.
Fixes: 03de6b2738 ("dmaengine: qcom-adm: stop abusing slave_id config")
Fixes: 5c9f8c2dbd ("dmaengine: qcom: Add ADM driver")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.11+
Link: https://lore.kernel.org/r/20220916041256.7104-1-ansuelsmth@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix broken slave_config function that uncorrectly compare the
peripheral_size with the size of the config pointer instead of the size
of the config struct. This cause the crci value to be ignored and cause
a kernel panic on any slave that use adm driver.
To fix this, compare to the size of the struct and NOT the size of the
pointer.
Fixes: 03de6b2738 ("dmaengine: qcom-adm: stop abusing slave_id config")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.17+
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220915204844.3838-1-ansuelsmth@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
These functions are defined in the edma.c file, but not called elsewhere,
so delete these unused functions.
drivers/dma/ti/edma.c:746:31: warning: unused function 'to_edma_cc'.
drivers/dma/ti/edma.c:420:20: warning: unused function 'edma_param_or'.
drivers/dma/ti/edma.c:414:20: warning: unused function 'edma_param_and'.
drivers/dma/ti/edma.c:402:20: warning: unused function 'edma_param_write'.
drivers/dma/ti/edma.c:373:28: warning: unused function 'edma_shadow0_read'.
drivers/dma/ti/edma.c:396:28: warning: unused function 'edma_param_read'.
drivers/dma/ti/edma.c:355:20: warning: unused function 'edma_or_array'.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2152
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20220914101943.83929-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver registration fails on SOC imx8mn as its supplier, the clock
control module, is probed later than subsys initcall level. This driver
uses platform_driver_probe which is not compatible with deferred probing
and won't be probed again later if probe function fails due to clock not
being available at that time.
This patch replaces the use of platform_driver_probe with
platform_driver_register which will allow probing the driver later again
when the clock control module will be available.
The __init annotation has been dropped because it is not compatible with
deferred probing. The code is not executed once and its memory cannot be
freed.
Fixes: a580b8c542 ("dmaengine: mxs-dma: add dma support for i.MX23/28")
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220921170556.1055962-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220803223448.6f08095b@endymion.delvare
Signed-off-by: Vinod Koul <vkoul@kernel.org>
>From the coccinelle check:
./drivers/dma/sf-pdma/sf-pdma.c
Error:line 409 is redundant because platform_get_irq() already prints an
error
./drivers/dma/sf-pdma/sf-pdma.c
Error:line 424 is redundant because platform_get_irq() already prints an
error
So,remove the unnecessary print function dev_err()
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220810062532.13425-1-ye.xingchen@zte.com.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
UDMA_CHAN_RT_*BCNT_REG stores the real-time channel bytecount statistics.
These registers are 32-bit hardware counters and the driver uses these
counters to monitor the operational progress status for a channel, when
transferring more than 4GB of data it was observed that these counters
overflow and completion calculation of a operation gets affected and the
transfer hangs indefinitely.
This commit adds changes to decrease the byte count for every complete
transaction so that these registers never overflow and the proper byte
count statistics is maintained for ongoing transaction by the RT counters.
Earlier uc->bcnt used to maintain a count of the completed bytes at driver
side, since the RT counters maintain the statistics of current transaction
now, the maintenance of uc->bcnt is not necessary.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20220802054835.19482-1-vaishnav.a@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32 MDMA can be triggered by STM32 DMA channels transfer complete.
In case of non-null struct dma_slave_config .peripheral_size, it means the
DMA client wants the DMA to trigger the MDMA.
stm32-mdma driver gets the request id, the mask_addr, and the mask_data in
struct stm32_mdma_dma_config passed by DMA with struct dma_slave_config
.peripheral_config/.peripheral_size.
Then, as DMA is configured in Double-Buffer mode, and MDMA channel will
transfer data from/to SRAM to/from DDR, then bursts are optimized.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220829154646.29867-7-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32 MDMA can be triggered by STM32 DMA channels transfer complete.
The "request line number" triggering STM32 MDMA is the STM32 DMAMUX channel
id set by stm32-dmamux driver in dma_spec->args[3].
stm32-dma driver fills the struct stm32_dma_mdma_config used to configure
the MDMA with struct dma_slave_config .peripheral_config/.peripheral_size.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220829154646.29867-6-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32 DMAMUX is used with STM32 DMA1 and DMA2:
- DMAMUX channels 0 to 7 are connected to DMA1 channels 0 to 7
- DMAMUX channels 8 to 15 are connected to DMA2 channels 0 to 7
STM32 MDMA can be triggered by DMA1 and DMA2 channels transfer complete,
and the "request line number" is the DMAMUX channel id (e.g. DMA2 channel 0
triggers MDMA with request line 8).
To well configure MDMA, set DMAMUX channel id in DMA features bitfield,
so that DMA can update struct dma_slave_config peripheral_config properly.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220829154646.29867-5-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Channels 0 to 3 flags are described in DMA_LISR and DMA_LIFCR (L as Low).
Channels 4 to 7 flags are described in DMA_HISR and DMA_HIFCR (H as High).
Macro STM32_DMA_ISR(n) returns the interrupt status register offset for the
channel id (n).
Macro STM32_DMA_IFCR(n) returns the interrupt flag clear register offset
for the channel id (n).
If chan->id % 4 = 2 or 3, then its flags are left-shifted by 16 bits.
If chan->id % 4 = 1 or 3, then its flags are additionally left-shifted by 6
bits.
If chan->id % 4 = 0, then its flags are not shifted.
Macro STM32_DMA_FLAGS_SHIFT(n) returns the required shift to get or set the
channel flags mask.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220829154646.29867-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The HiSilicon IP08 and HiSilicon IP09 are DMA iEPs, they
have the same pci device id but different pci revision.
Unfortunately, they have different register layouts, so
the origin driver cannot run on HiSilicon IP09 correctly.
This patch enables the driver to adapt to HiSilicon IP09.
HiSilicon IP09 offers 4 channels, each channel has a send
queue, a complete queue and an interrupt to help to do tasks.
This DMA engine can do memory copy between memory blocks.
Signed-off-by: Jie Hai <haijie1@huawei.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Link: https://lore.kernel.org/r/20220830062251.52993-6-haijie1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
