Add support for HW QAT Power Management (PM) feature.
This feature is enabled at init time (1) by sending an admin message to
the firmware, targeting the admin AE, that sets the idle time before
the device changes state and (2) by unmasking the PM source of interrupt
in ERRMSK2.
The interrupt handler is extended to handle a PM interrupt which
is triggered by HW when a PM transition occurs. In this case, the
driver responds acknowledging the transaction using the HOST_MSG
mailbox.
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Co-developed-by: Marcinx Malinowski <marcinx.malinowski@intel.com>
Signed-off-by: Marcinx Malinowski <marcinx.malinowski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add and use the new helper function adf_get_pmisc_base() where convenient.
Also:
- remove no longer shared variables
- leverage other utilities, such as GET_PFVF_OPS(), as a consequence
- consistently use the "pmisc_addr" name for the returned value of this
new helper
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Introduce admin AE mask. If this mask set, the fw constant message is
sent only to engines that belong to that set, otherwise it is sent to
all engines.
This is in preparation for the qat_4xxx driver where the constant message
should be sent only to admin engines.
In GEN2 devices (c62x, c3xxx and dh895xcc), the admin AE mask is 0 and
the fw constants message is sent to all AEs.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Call adf_set_fw_constants() before adf_init_ae().
This is required by QAT GEN4 devices, which expect that the
FW_CONSTANTS_CFG command is sent to the admin AEs before the FW_INIT_AE
command.
Swapping the order of the two commands (FW_INIT_AE and FW_CONSTANTS_CFG)
is allowed in QAT GEN2 devices as the firmware can handle those in any
order.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The mailbox CSR register has a write latency and requires a delay before
being read. This patch replaces readl_poll_timeout with read_poll_timeout
that allows to sleep before read.
The initial sleep was removed when the mailbox poll loop was replaced with
readl_poll_timeout.
Fixes: a79d471c65 ("crypto: qat - update timeout logic in put admin msg")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the logic that sends admin messages to be able to target a subset
of Acceleration Engines (AEs) in the device.
In future not all admin messages need to be sent to all the AEs.
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch tidies up the definition of init/admin request and response
messages by removing the icp_qat_fw_init_admin_resp_pars structure
and embedding it into icp_qat_fw_init_admin_resp.
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move qat_isr.c and qat_isrvf.c files to qat_common dir
so that they can be reused by all devices.
Remove adf_drv.h files because thay are not longer needed.
Move adf_dev_configure() function to qat_common so it can be reused.
Also some minor updates to common code for multidevice.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adf admin and HW arbiter function can be used by dh895xcc specific code
well as the new dh895xccvf and future devices so moving them to
qat_common so that they can be shared.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
