fm10k supports up to 184 bytes of inner+outer headers. Add an initial
check to fail encap offload if these are too large.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.
It also cleans up how we clear the descriptor status bits. Previously they
were zeroed as a part of clearing the hdr_addr. However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems. Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared. As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that dma_rmb is used when reading the Rx
descriptor. The advantage of dma_rmb is that it allows for a much
lower cost barrier on x86, powerpc, arm, and arm64 architectures than a
traditional memory barrier when dealing with reads that only have to
synchronize to coherent memory.
In addition I have updated the code so that it just checks to see if any
bits have been set instead of just the DD bit since the DD bit will always
be set as a part of a descriptor write-back so we just need to check for a
non-zero value being present at that memory location rather than just
checking for any specific bit. This allows the code itself to appear much
cleaner and allows the compiler more room to optimize.
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces calls to netdev_alloc_skb_ip_align with
napi_alloc_skb. The advantage of napi_alloc_skb is currently the fact that
the page allocation doesn't make use of any irq disable calls.
There are few spots where I couldn't replace the calls as the buffer
allocation routine is called as a part of init which is outside of the
softirq context.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.
Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel drivers were pretty much just using the plain vanilla GFP flags
in their calls to __skb_alloc_page so this change makes it so that they use
dev_alloc_page which just uses GFP_ATOMIC for the gfp_flags value.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for skb->xmit_more based on the changes that were
made to igb to support the feature. The main changes are moving up the
check for maybe_stop_tx so that we can check netif_xmit_stopped to determine
if we must write the tail because we can add no further buffers.
Acked-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is illegal to use atomic_set(&page->_count, 2) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for the Linux PTP Hardware clock and timestamping
functionality provided by the hardware. There are actually two cases that
this timestamping is meant to support.
The first case would be an ordinary clock scenario. In this configuration
the host interface does not have access to BAR 4. However all of the host
interfaces should be locked into the same boundary clock region and as such
they are all on the same clock anyway. With this being the case they can
synchronize among themselves and only need to adjust the offset since they
are all on the same clock with the same frequency.
The second case is a boundary clock scenario. This is a special case and
would require both BAR 4 access, and a means of presenting a netdev per
boundary region. The current plan is to use DSA at some point in the
future to provide these interfaces, but the DSA portion is still under
development.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds limited debugfs support for the driver. Most of the
functionality needed for dumping registers is already provided via ethtool.
The only thing we saw that we really neeed was the ability to dump the
descriptor rings so as such this patch will add a fm10k directory containing a
listing of directories each one with a unique PCI Bus, Device, and Function
number. Each of those BDF directories will have a list of q_vectors, and
the q_vectors will contain a file for each of the Rx/Tx rings that are a part
of the vector. For example:
# ls -RD /sys/kernel/debug/fm10k/
/sys/kernel/debug/fm10k/:
0000:01:00.0
/sys/kernel/debug/fm10k/0000:01:00.0:
q_vector.000 q_vector.001 q_vector.002 q_vector.003
/sys/kernel/debug/fm10k/0000:01:00.0/q_vector.000:
rx_ring.000 tx_ring.000
/sys/kernel/debug/fm10k/0000:01:00.0/q_vector.001:
rx_ring.001 tx_ring.001
/sys/kernel/debug/fm10k/0000:01:00.0/q_vector.002:
rx_ring.002 tx_ring.002
/sys/kernel/debug/fm10k/0000:01:00.0/q_vector.003:
rx_ring.003 tx_ring.003
# cat /sys/kernel/debug/fm10k/0000:01:00.0/q_vector.000/rx_ring.000
DES DATA RSS STATERR LENGTH VLAN DGLORT SGLORT TIMESTAMP
---------------------------------------------------------------------------
000 0x00000000 0x00000000 0x00000003 0x002a 0x0000 0x0000 0x0000 0x13951807dc4fedf0
001 0x00000000 0x00000000 0x00000003 0x002a 0x0000 0x0000 0x0000 0x1395180906c9f2c8
002 0x3731c000 0x00000000 0x00000000 0x0000 0x0000 0x0000 0x0000 0x0000000000000000
003 0x3731d000 0x00000000 0x00000000 0x0000 0x0000 0x0000 0x0000 0x0000000000000000
004 0xaab3a000 0x00000000 0x00000000 0x0000 0x0000 0x0000 0x0000 0x0000000000000000
...
# cat /sys/kernel/debug/fm10k/0000:01:00.0/q_vector.000/tx_ring.000
DES BUFFER_ADDRESS LENGTH VLAN MSS HDRLEN FLAGS
---------------------------------------------------------
000 0x00000000aa8a1002 0x005a 0x0000 0x0000 0x0000 0xc0
001 0x00000000aa8a2002 0x005a 0x0000 0x0000 0x0000 0xc0
002 0x000000006bc13202 0x004e 0x0000 0x0000 0x0000 0xc0
003 0x000000006bc13c02 0x002a 0x0000 0x0000 0x0000 0xe1
004 0x000000006bc13602 0x0062 0x0000 0x0000 0x0000 0xc0
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for L2 MACVLAN by making use of the fact that the
RRC provides a unique tag per filter called a Global Resource Tag, or GLORT.
In the case of this offload what I have done is assigned a linear block of
these so that each GLORT represents one of the MACVLAN netdevs. By doing
this I can share the Rx queues and Tx queues for all of the MACVLAN netdevs
while allowing them to be demuxed in the Rx cleanup path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for basic offloads including TSO, Tx checksum, Rx
checksum, Rx hash, and the same features applied to VXLAN/NVGRE tunnels.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch takes the driver from supporting a single queue to supporting
multiple queues. The upper queue limit for the PF is 128 queues and the
upper limit for the VF is (128 / num_vfs) rounded down to nearest power of 2.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds the transmit and receive fastpath and interrupt handlers.
With this code in place the network device is now able to send and receive
frames over the network interface using a single queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds the defines and structures necessary to support both Tx
and Rx descriptor rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch set adds interrupt support for the fm10k interfaces. The
interfaces themselves only support MSI-X, so neither MSI or legacy
interrupts are used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the basic defines and structures needed by the PF for
operation.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the beginning framework onto which I am going to add the
fm10k driver which supports the Intel(R) FM10000 Ethernet Switch Host
Interface.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
