It's possible to derive rate index from bitrate
without any additional mapping structures/logic.
This should have little to none impact on
performance since this is only done for management
frames and the previous approach wasn't
particularly optimized.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using a hacky table and magic values
use supported band information advertised to
mac80211.
This may impact performance a little when dealing
with legacy rx rates depending on system
architecture. It's probably negligible.
This also fixes a highly theoretical corner case
when HT/VHT rates weren't reported correctly if
channel frequency wasn't known.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the existing ieee80211_rate array instead of
definining separate one. This gets rid of the ugly
4-index offset when dealing with 5GHz band.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using raw values is discouraged. Having
defines/enums is preferred.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was superfluous and confusing. It's better to
define the structure explicitly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to store rate values in hw_value.
This frees up the hw_value for better future use.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Prepare the code for future changes so that new
code can refer to rate-related stuff without
forward declarations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch introduces tdls without tdls peer uapsd and tdls channel switching.
Transmitting tdls data frames works only for ethernet type frames, that's why
data addressed to tdls sta is in ethernet format.
This patch depends on commit c23e31cf7b ("mac80211: initialize rate control
earlier for tdls station").
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently station counting functions
(inc_num_stations/dec_num_stations) does not handle
tdls type of stations. Tdls station should be counted
because it consumes peer in firmware. Only not tdls
stations are excluded from this counting.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Peer type was hardcoded to default value.
For future implementation it is required
to make is configurable.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are a few different tx paths depending on
firmware and frame itself.
Creating a uniform decision will make it possible
to switch between different txmode easier, both
for testing and for future features as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If htt.freq isn't cleared and contains garbage fw
may discard tx packets. Prevent this from
happening by clearing htt.freq properly.
Possible manifestation of the problem could be not
being able to send auth request/response frames on
firmware with HTT >= 3.4 (when freq param was
introduced), e.g. on qca6174.
Fixes: 8d6d362436 ("ath10k: fix offchan reliability")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Patch "ath10k: introduce basic tdls functionality" depends on this mac80211
patch:
c23e31cf7b mac80211: initialize rate control earlier for tdls station
Add support for WOW disconnect and magic-packet.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that ANI is enabled by default, allow user to disable or enable ANI feature
from debugfs
echo 0|1 > /sys/kernel/debug/ieee80211/phyX/ath10k/ani_enable
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ANI helps to improve connectvity and performance in a noisy environment.
Enabling this feature would help the user experience a better and stable
wireless connection in a noisy environmnet. This feature is currently not
enabled for ath10k. Enable this feature by default.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable channel 144 on 5GHz band since 802.11ac introduced it.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Thermal throttling is not handled in software restart and device
bootup. Also it needs to be configured whenever quiet period got
updated. Fix that.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By default rts protection is enabled in firmware for the second
rateset. Currently ath10k selects RTS profile (only for software
retries), when legacy stations are associated or asked by mac80211.
On congested environment, when AP is running in HT/VHT mode and
there are no legacy clients associated, this will impact the
robustness. Also enabling RTS protection only for second rateset will
not impact performance on clear environment. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setup maximum number of associated stations supported in
AP/P2P_GO mode.
This allow hostapd/wpa_supplicant to play with that limit
and set more information (eg. P2P group limit bit for P2P_GO).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
NativeWifi tx mode expects QoS Data frames to be
delivered as Data frames with QoS part (e.g. tid)
being delievered out-of-band in fw tx command.
The QoS bit wasn't stripped before submitting to
firmware.
Stripping fixes two known problems:
* qca6174 IOT with some APs, e.g.
Cisco AIR-AP 1252 (which would crash after
ath10k association). Some ath9k APs would
crash as well.
* sniffing own tx frames via radiotap because,
e.g. wireshark was seeing QoS bit set but
since QoS Control was stripped in ath10k it
would parse beginning of LLC/SNAP
>From debugability point of view this removes the
ability to distinguish QoS from non-QoS frames
when sniffing own tx via radiotap. On the other
hand frames can be now parsed correctly without
special software modification.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While testing with older supplicant, .drv_set_key() was failing due to
higher than ath10k firmware could handle key_index (WMI_MAX_KEY_INDEX == 3).
--
wpa_driver_nl80211_set_key: ifindex=15 alg=4 addr=0x7f02b129fbe3 key_idx=4 set_tx=0 seq_len=6 key_len=16
broadcast key
nl80211: set_key failed; err=-22 Invalid argument)
wlan0: WPA: Failed to configure IGTK to the driver
wlan0: RSN: Failed to configure IGTK
--
In order to fix this case (PMF: AES-CMAC/IGTK) force the AES_CMAC cipher to
be handled by software.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions (e.g. qca6174 with fw73)
don't deliver beacons to host reliably. This
causes random disconnects even in perfect
conditions. This is most visible with
multi-channel operation.
All available firmware revisions seem to support
beacon miss offloading so there shouldn't be any
problems.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 370e567363 ("ath10k: fix broken traffic for 802.1x in client mode")
introduced a regression on WPA crypto. All keys were treated as if they were
WEP which resulted in WPA being incorrectly installed to fw/hw and subsequently
no traffic.
Reported-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 548462133d ("ath10k: fix interrupt storm") introduced a
regression. The condition responsible for bringing up monitor vdev was broken
and it was never started for CAC so effectivelly CAC would not detect radar
pulses.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Mistakenly v1 of `ath10k: fix AP/IBSS CSA with
template based fw`
(81a9a17db5) was
applied.
This patch applies the missing bits from v2:
* remove unnecessary locking
* add some (sanity) checks
There are no practical functionality differences
between v1 and v2.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Promiscuous mode is enabled when wlan interface is added to
bridge. ath10k creates a monitor mode when promiscuous mode
is enabled. When monitor vdev is running along with other
vdev(s) there is a huge number of interrupts generated
especially in noisy condition. Fix this by not enabling
promiscuous(monitor) mode when already a vdev is running.
As disabling promiscuous mode may have issues with 4-address
bridging in STA mode, the change is done specific to non-sta/ibss
mode types. This does not change the support of virtual interface of
type monitor along with other vdevs of any type.
This could fix management frame drop in fw due to unavailable
buffers because in monitor mode device receives everything seen
on the air. In noisy condition, disabling monitor mode helps assoc
go through without any issue.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patches does not modify any functionality. Just a code move
so that ath10k_vdev_stop() can be used in ath10k_vdev_start_restart()
for any failure cases which involves vdev_stop().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This improves coexistance with 11b legacy devices
on wmi-tlv and qca6174.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware doesn't report a complete and
ready-to-use vht cap. Instead the driver is
supposed to fill in the missing bits related to
number of chains.
This effectively increases Compressed Steering
Number and Number of Sounding Dimensions in
AssocReq frames for devices with more than one RF
chain and should improve TxBF performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When WEP keys are uploaded it's possible that
there are stations associated already (e.g. when
merging) without any keys. Static WEP needs an
explicit per-peer key upload.
Make sure to re-upload wep keys if necessary.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When running 802.1x WEP keys must be installed
without pairwise-groupwise swap (which is
necessary for static WEP).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 with wmi-tlv firmware uses offloaded
beaconing scheme (i.e. templates). This requires a
little different approach when implementing CSA.
Add missing code to update CS count and report CSA
completion to mac80211. Without it channel switch
was never finished.
To avoid races during interface teardown data_lock
has been used to protect is_up and is_started so
they can be compared against before scheduling
count down work.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
brcmfmac:
* sdio improvements
* add a debugfs file so users can provide us all the revinfo we could
ask for
iwlwifi:
* add triggers for firmware dump collection
* remove support for -9.ucode
* new statitics API
* rate control improvements
ath9k:
* add per-vif TX power capability
* BT coexistance fixes
ath10k:
* qca6174: enable STA transmit beamforming (TxBF) support
* disable multi-vif power save by default
bcma:
* enable support for PCIe Gen 2 host devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU+dliAAoJEG4XJFUm622bsqQH/RO1Gxuw6hmiHPeeIcoDmlvt
MZKvy6xcAiFqREfGwDxjVminlTZ7/MB9bABeaoQKzpQFpCJW/ftjIqwfbRqZWsvG
3IC0s2nPTwWU8YSsZTbifnyXCVNQDJuE+5nQ3hMO2rE/dZDi1zt1fS2hiSXtlASS
kgBJcfXgoVxvhZ1WI+uVpbU0RtwXmI7tVylREE1sbgCrg7AuJx4Q2QmZ1GioPRLy
20HnFVFcIcbHk4eXVwAJOspdjctujoR858pg/oxlcVXWb7MOOCV/Fk8WMursZxFh
qj/I/kbDcFYh3H5uC+6qL/kRByY80/yckLDiMbghA0QR5/PSx2nvp/UfkqIf008=
=qgVl
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-03-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Major changes:
brcmfmac:
* sdio improvements
* add a debugfs file so users can provide us all the revinfo we could
ask for
iwlwifi:
* add triggers for firmware dump collection
* remove support for -9.ucode
* new statitics API
* rate control improvements
ath9k:
* add per-vif TX power capability
* BT coexistance fixes
ath10k:
* qca6174: enable STA transmit beamforming (TxBF) support
* disable multi-vif power save by default
bcma:
* enable support for PCIe Gen 2 host devices
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all firmware revisions have a proper
multi-interface client powersaving implementation,
e.g. qca6174 WLAN.RM.2.0-00073.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6184 WLAN.RM.2.0-00073 has a bug in sta
powersave state machine and requires peer param to
be poked to enable the powersave.
Calling this unconditionally should be safe for
other chips/firmwares.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the built-in function instead of memset.
Miscellanea:
Add #include <linux/etherdevice.h> where appropriate
Use ETH_ALEN instead of 6
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.11ad adds new a network type (PBSS) and changes the capability
field interpretation for the DMG (60G) band.
The same 2 bits that were interpreted as "ESS" and "IBSS" before are
re-used as a 2-bit field with 3 valid values (and 1 reserved). Valid
values are: "IBSS", "PBSS" (new) and "AP".
In order to get the BSS struct for the new PBSS networks, change the
cfg80211_get_bss() function to take a new enum ieee80211_bss_type
argument with the valid network types, as "capa_mask" and "capa_val"
no longer work correctly (the search must be band-aware now.)
The remaining bits in "capa_mask" and "capa_val" are used only for
privacy matching so replace those two with a privacy enum as well.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
[rewrite commit log, tiny fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If firmware advertises support for TxBF then the
driver has to instruct the firmware accordingly
during runtime. Without this patch connecting to
an AP with beamformer support would yield abysmal
Rx performance.
This has been tested with wmi-tlv and qca6174
while acting as a STA beamformee only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't notify host about
self-bss-peer removal until after associated vdev
is deleted. This has been observed with qca6174
WLAN.RM.2.0-00073 firmware.
This patch fixes AP teardown slowdowns and
prevents delays and warnings:
ath10k_pci 0000:00:05.0: failed to remove peer for AP vdev 0: -110
ath10k_pci 0000:00:05.0: removing stale peer xx:xx:xx:xx:xx:xx from vdev_id 0
ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 24
ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 8
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A bit of general cleanup to make debug messages more useful.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case firmware fails to start the scan, then complete
the start condition and clean up so that driver does not
block on timeout.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
iwlwifi:
* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)
* add support for beamforming
* enable stuck queue detection for iwlmvm
* a few fixes for EBS scan
* fixes for various failure paths
* improvements for TDLS Offchannel
wil6210:
* performance tuning
* some AP features
brcm80211:
* rework some code in SDIO part of the brcmfmac driver related to
suspend/resume that were found doing stress testing
* in PCIe part scheduling of worker thread needed to be relaxed
* minor fixes and exposing firmware revision information to
user-space, ie. ethtool.
mwifiex:
* enhancements for change virtual interface handling
* remove coupling between netdev and FW supported interface
combination, now conversion from any type of supported interface
types to any other type is possible
* DFS support in AP mode
ath9k:
* fix calibration issues on some boards
* Wake-on-WLAN improvements
ath10k:
* add support for qca6174 hardware
* enable RX batching to reduce CPU load
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU1fUoAAoJEG4XJFUm622bnjMH/25f2kyLAJSLJmiIhpEcYlNJ
CJMAYsSTcqhKaMEbx742StUUDH3pa1oV4mQ5csVa2QJIsS90WzPpB1eRnNtQ69Nj
89Zfwa6bbX0TXDgw1Aa28NewPY/3xWpCjI03HBQaMIncToWv3/dzNUr0bEmIuBds
wsr5Y+fy80VKnkoXG7XzGFOqmxxFwNS+UF3M1WNtQ+xcr9rK3/LLxyWFy84S9UIe
4lVOb+df91YFIJeLs28/hfTiRhvV0fWIbupGv8UhuBMho+F0dpLvra+3xksEqALu
4+AzI0j9GjqFfMzbmRBcPcT4Rl37nLmvQ+7XokrFgAYS5zp7OGylOMU3nHyvkuY=
=iL8v
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Major changes:
iwlwifi:
* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)
* add support for beamforming
* enable stuck queue detection for iwlmvm
* a few fixes for EBS scan
* fixes for various failure paths
* improvements for TDLS Offchannel
wil6210:
* performance tuning
* some AP features
brcm80211:
* rework some code in SDIO part of the brcmfmac driver related to
suspend/resume that were found doing stress testing
* in PCIe part scheduling of worker thread needed to be relaxed
* minor fixes and exposing firmware revision information to
user-space, ie. ethtool.
mwifiex:
* enhancements for change virtual interface handling
* remove coupling between netdev and FW supported interface
combination, now conversion from any type of supported interface
types to any other type is possible
* DFS support in AP mode
ath9k:
* fix calibration issues on some boards
* Wake-on-WLAN improvements
ath10k:
* add support for qca6174 hardware
* enable RX batching to reduce CPU load
Conflicts:
drivers/net/wireless/rtlwifi/pci.c
Conflict resolution is to get rid of the 'end' label and keep
the rest.
Signed-off-by: David S. Miller <davem@davemloft.net>
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
-----BEGIN PGP SIGNATURE-----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=wOaR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-02-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
Ath10k driver sets wrong default key idx that results in
sending unicast frames with multicast key.
The reason for this behavior is that cached broadcast key
is installed for station MAC address on association. After
dot1x completes, unicast key is installed for station
MAC address. Default key idx is set to broadcast key id when
driver tries to send broadcast frame. This causes firmware
to use broadcast key id to transmit unicast frames to stations.
Used TX_USAGE flag to set default key for stations.
Added callback for setting unicast default idx which will be
invoked on every default key idx configuration.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable the MCS8 and MCS9 support for 2.4G band, it will
use these data rate with other devices having the same
capability.
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware revisions providing sta keepalive service
have it enabled by default.
mac80211 already does idle connection polling so
it makes no sense to duplicate this in ath10k.
mac80211 wouldn't even know of the offloaded
keepalive NullFunc frames.
This prevents sending out some extraneous frames
on the air.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New wmi-tlv firmware for qca6174 supports this.
This should fix issues related to multi-vif WMM.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 already requests WMM per vif but firmware
wasn't able to handle this until now. However new
wmi-tlv firmware for qca6174 is capable of this.
This prepares per-vif WMM param setup.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Software encryption was never necessary.
Tested with fw 636 and fw 10.x.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only userspace can make an educated decision when
a trigger frame is required so make sure the
autotrigger service is disabled.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The workaround couldn't work correctly because the
802.11 header wasn't properly stripped of QoS Data
bit so it wasn't recognized in the later parts of
tx path as NullFunc frame and ended up in HTT Tx
instead of HTT Mgmt Tx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware supporting beacon templates (i.e. wmi-tlv
for qca6174) doesn't implicitly take dtim period
from the template. Instead it requires vdev param
to be set accordingly.
This fixes dtim period being stuck at 3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath10k driver only supports HW crypto (except for management
frames or so - CMAC needs to be done in software). Make it use
the new IEEE80211_HW_SW_CRYPTO_CONTROL flag to ensure mac80211
doesn't erroneously attempt to use software crypto.
Taking through my tree after Kalle's ACK to avoid breaking the
ath10k driver with the next crypto patches.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a comment for indicating that the ATH10K_SCAN_RUNNING case falls
through to the ATH10K_SCAN_ABORTING case in __ath10k_scan_finish. This
will document that the lack of a break is intentional.
Coverity: CID 1260017
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions support beacon and probe
response templates instead. This means SWBA events
are no longer delivered for these firmware
revisions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wait_for_completion_timeout does not return negative values so the tests
for <= 0 are not needed and the case differentiation in the error handling
path unnecessary.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add per station debugfs files when a station is added to mac80211's
station list. This helps to group peer specific debugfs entries
altogether. Right now this callback adds support to test aggregation
procedures (addba/addba_resp/delba) manually.
To enable automatic aggregation in target,
echo 0 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
For manual mode,
echo 1 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
phymode should use 11b only if NO_OFDM flags is set.
Hence check up channel flag for NO_OFDM and set to
11b.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Assoc peer command contain information about NSS.
When we will get IEEE80211_RC_NSS_CHANGED we should
also send (re) assoc peer command to be sure firmware
will know about it and RC will work correctly.
This was found during code review.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fix TX problem when IBSS used in HT mode.
Before we used 6Mbps all the time for TX direction.
Reported-by: Yeoh Chun-Yeow <yeohchunyeow@gmail.com>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4 firmware uses bitmask in wmi_resource_config to configure
10.2 firmware features like airtime fairness and rx batch mode instead
of maintaining separete bool entry. This allows new features that can be
configure during init time without breaking backward compatibility.
kvalo: use WMI op version, bump up FW API to 4 to not break older versions of
ath10k
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ATH10K_FW_FEATURE_WMI_10X should not be used for anymore as that's
now deprecated, instead use wmi op version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware doesn't allow precise tx rate control so
P2P wasn't entirely spec compliant (it was using
CCK rates in some cases).
The only way to make sure firmware doesn't use CCK
rates is to have a vdev with P2P subtype used for
scanning and tx. This can be done via a special
dedicated P2P device interface support.
This also removes the ancient hack from ath10k in
favor of p2pdev.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per-vif bss_conf.ps should be used to configure
powersave.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting 0 ps timeout to firmware yields very poor
latency and traffic issues. This is the case when
multi-vif is active.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To comply with WMM-PS the device shouldn't wake up
with a NullFunc frame pair when tx-ing. Instead PM
bit on each tx frame should be used.
To make this work correctly firmware needs to be
told to use a different STA PS wake threshold when
u-APSD is enabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions need peer phymode to be
specified as MODE_11B when associating as station
to a 11b AP. Otherwise they can starve other
stations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting fragmentation threshold has not been supported by
any of firmware versions, hence unregister the callback and
remove the function.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the 10.x fw branch support was introduced it
became apparent ath10k will need to be able to
deal with different fw ABIs eventually.
The patch creates an abstraction for dealing with
command and event structures across different ABIs
and mostly gets rid of the
ATH10K_FW_FEATURE_WMI_10X flag usage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Increase the rts threshold from the legacy value of 2347 to support higher
threshold limit.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of peers isn't directly translatable to
the number of stations because ath10k needs to
reserve a few extra peers for special cases like
multi-vif concurrency.
The previous limit was 126 and 15 stations in AP
mode for 10.x and main firmware branches
respectively. The limit is now 128 and 16 which
was the original intention.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The var was supposed to be protected by data_lock
but it wasn't so in all instances. It's actually
not necessary to have a spinlock protected
num_peers so drop it.
All instances of num_peers are already within
conf_mutex sections so use that.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents warning spamming if peer creation
fails during sta_state in some cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_tx_wep_key_work() acquires conf_mutex, so
cancelling it when conf_mutex is already taken
in ath10k_remove_interface() is incorrect, so
move it outside the lock.
Snippet from the lockdep report:
kernel: ======================================================
kernel: [ INFO: possible circular locking dependency detected ]
kernel: 3.18.0-rc5-wl-debug #34 Tainted: G O
kernel: -------------------------------------------------------
kernel: hostapd/451 is trying to acquire lock:
kernel: ((&arvif->wep_key_work)){+.+...}, at: [<ffffffff810872d5>] flush_work+0x5/0x290
kernel: but task is already holding lock:
kernel: (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa0b99f00>] ath10k_remove_interface+0x40/0x290 [ath10k_core]
kernel: which lock already depends on the new lock.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
peer->keys needs to be protected by data_lock
since it is also accessed from the WMI path.
Both install() and clear() routines for peer
keys modify the key contents, so use the data_lock
to avoid races.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When static keys are used in shared WEP, when a
station is associated, message 3 is sent with an
encrypted payload. But, for subsequent
authentications that are triggered without a
deauth, the auth frame is decrypted by the HW.
To handle this, check if the WEP keys have already
been set for the peer and if so, mark the
frame as decrypted. This scenario can happen
when a station changes its default TX key and initiates
a new authentication sequence.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When mac80211 requests driver to cancel a hw roc
the driver must not call the expired() callback or
else roc will fail in some cases depending on how
things get scheduled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With P2P concurrency requested hw roc duration
time can be very small. Some firmware revisions
refuse scan requests with too small channel dwell
time.
This prevents messages like, e.g. with connected
STA vif and performing P2P Find:
ath10k_pci 0000:00:05.0: failed to switch to channel for roc scan
ieee80211 phy3: failed to start next HW ROC (-110)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions don't need peer creation
when doing offchannel tx. Earlier revisions would
queue and never release frames without a peer.
This prevent new firmware revisions from stopping
replenishing wmi-htc tx credits and improves
reliability of offchannel tx which would sometimes
silently fail.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Comment was out-of-date. The headroom is no longer
necessary because HTT Tx fragment list is stored
in dma pool item associated with each sk_buff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When re-associating a station, the nss was set back to
maximum value even if user had configured small number
of tx chains. So, pay attention to user's config in
this case as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It appears it takes more than just setting the
hardware's chainmask to make things work well. Without
this patch, a vdev would only use 1x1 rates when chainmask
was set to 0x3.
Setting the 'nss' (number of spatial streams) on the vdev
helps the firmware's rate-control algorithm work properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo <kvalo@qca.qualcomm.com> says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions
-----BEGIN PGP SIGNATURE-----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=6GIj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This relatively large batch of changes is comprised of the
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
Conflicts:
drivers/net/wireless/ath/wil6210/cfg80211.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).
Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.
Update the current users with the new prototype.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases hw recovery was taking an absurdly
long time due to ath10k waiting for things that
would never really complete.
Instead of waiting for inevitable timeouts poke
all completions and wakequeues and check if it's
still worth waiting.
Reading/writing ar->state requires conf_mutex.
Since waiters might be holding it introduce a new
flag CRASH_FLUSH so it's possible to tell waiters
to abort whatever they were waiting for.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rts threshold was being configured instead of
fragmentation threshold.
Keep in mind available firmware binaries don't
seem to support fragmentation anyway so this
doesn't fix fragmentation threshold per se.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When user space requests survey info, it is useful to know which of the survey
data refers to the channel that is currently actively being used. One of the
use cases is getting the current channel noise for status output. Without this
flag you would have to look up the channel separately and then compare it
against the frequency in the survey output in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This simply changes the source for txpower setup.
It does not make ath10k use different txpower
values for different vifs.
This will make it easier to implement chanctx in
ath10k in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code can be symmetrical so make it so. This
makes it easier to understand and work with.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to reconfigure peer
completely upon reassociation. This will make it
easier to have a more uniform association code
across different modes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to pass bss_conf explicitly as it
is accessible via vif pointer. This requires
slight changes in function prototypes. While at it
clean up listen interval workaround/command.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Based on GFP flag given to DMA coherent allocation, the behaviour of
dma_free_coherent is changed. This behavioural diffrence is noticeable
in ARM platform. If DMA memory is allocated with GFP_KERNEL, free
coherent can not be called inside spin lock. This is causing kernel
crash in ARM platforms. Fix this by changing GFP flag to atomic.
This is most likely a regression from commit 64badcb6d6 ("ath10k: workaround
fw beaconing bug").
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary to create bssid peer for
bssid. Self-address peer is sufficient.
This prevents some firmware revisions from crashing.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can allow more than 32 stations to be supported
without over-running the bitmap.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for reading firmware stats through the ethtool
API. This may be easier for applications to manipulate
compared to parsing a text based debugfs file.
kvalo: remove unneeded ifdefs, call ath10k_debug_fw_stats_request() and added
simple error handling
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The structure is being set up in 2 places.
Deduplicate the code by creating a helper.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware reports the number of RF chains so use
that for initialization of supp_{tx,rx}_chainmask
instead of using a macro for 3x3 chips.
This should make tx/rx chainmask reports correct
for chips other than 3x3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't wait for beacon tx
completion before sending another SWBA event. This
could lead to hardware using old (freed) beacon
data in some cases, e.g. tx credit starvation
combined with missed TBTT. This is very very rare.
On non-IOMMU-enabled hosts this could be a
possible security issue because hw could beacon
some random data on the air. On IOMMU-enabled
hosts DMAR faults would occur in most cases and
target device would crash.
Since there are no beacon tx completions (implicit
nor explicit) propagated to host the only
workaround for this is to allocate a DMA-coherent
buffer for a lifetime of a vif and use it for all
beacon tx commands. Worst case for this approach
is some beacons may become corrupted, e.g. garbled
IEs or out-of-date TIM bitmap.
Keep the original beacon-related code as-is in
case future firmware revisions solve this problem
so that the old path can be easily re-enabled with
a fw_feature flag.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As suggeested by checkpatch:
WARNING: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)
In wmi.c I had to change due to sparse warnings copying of struct wmi_mac_addr
from form &cmd->peer_macaddr.addr to cmd->peer_macaddr.addr. In
ath10k_wmi_set_ap_ps_param() I also added the missing ".addr" to the copy
command.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
WARNING: Missing a blank line after declarations
Please note that some of the cases I fixed by moving the variable declarations
to the beginning of the function, which is the preferred style in ath10k.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed.
-----BEGIN PGP SIGNATURE-----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=OPIp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
Conflicts:
net/mac80211/iface.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add testmode interface for starting and using UTF firmware which is used to run
factory tests. This is implemented by adding new state ATH10K_STATE_UTF and user
space can enable this state with ATH10K_TM_CMD_UTF_START command. To go back to
normal mode user space can send ATH10K_TM_CMD_UTF_STOP.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the new static_smps / dynamic_smps feature bits
instead of mac80211-internal hw flags.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Nothing important was being overwritten so it
didn't yield any bugs yet.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents some fw revisions from crashing in
many cases when user is trying to run a
promiscuous station interface (e.g. sniffing,
4addr bridge).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix some cases where monitor start failure left
the driver in a confused state.
This also makes the monitor code simpler.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If a station was reassociated, i.e. due to change
of supported rates update via sta_rc_update() the
num_legacy_stations would be (incorrectly) bumped
up leading to unbalanced usage of the var. This in
turn could lock rtscts protection up as enabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it a lot easier to log and debug
messages if there's more than 1 ath10k device on a
system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Check vdev map has space before calling ffs,
fix invalid cleanup in failure to create vdev
case.
Open-code the BIT() logic since BIT does not properly
handle 64-bit bitfields and future patches will make
use of larger bitfields.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the common convention of embedding private
structures inside parent structures. This
reduces allocations and simplifies pci probing
code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This aims at fixing some rare scan bugs related to
firmware reporting unexpected scan event
sequences.
One such bug was if spectral scan phyerr reporting
prevented firmware from properly propagating scan
events to host. This led to scan timeout. After
that next scan would trigger scan completed event
first (before scan started event) leading to
ar->scan.in_progress and timeout timer states to
be overwritten incorrectly and making the very
next scan to hang forever.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adds the spectral scan feature for ath10k. The spectral scan is triggered by
configuring a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.
Essentially, to try it out:
ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples
This feature is still experimental. Based on the original RFC patch of
Sven Eckelmann.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases during heavy tx vdev stop-start
would timeout on vdev synchronization causing
traffic to stall for a few seconds.
Instead of stop-starting use a dedicated vdev
restart command and down vdevs explicitly before
doing so.
This gets rid of the synchronization
warnings/timeouts and makes channel switching
smoother during traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.x firmware does not support IBSS mode at
all. It can't beacon and it crashes when trying to
scan.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware doesn't perform Rx reordering so it is
left to the host driver to do that.
Use mac80211 to perform reordering instead of
re-inventing the wheel.
This fixes TCP throughput issues in some
environments.
Reported-by: Denton Gentry <denton.gentry@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently fw/hw generates a corrupted QoS Control
Field in Qos NullFunc frames. The only way to
workaround this is to downgrade frames to
NullFunc. This should be okay since powersave is
done by fw/hw and these frames are only used for
CQM purposes (e.g. from hostapd to check if
station is still connected).
This doesn't fix any user visible bug that I know
of. It just prevents from sending out funky frames
on the air.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It always bugged me how tid is computed and stored
in a temporary var before written to the control
buffer. It was confusing and it made it difficult
to work with tx helpers.
While at it rename the qos workaround function as
it was misleading - it's not a workaround but
preparation for nwifi tx mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.
As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
FW creates self-peer for AP internally.
This prevents ath10k from trying to create
explicit self-peer during hw recovery and thus
prevents a timeout and a warning during teardown:
ath10k: removing stale peer $AP_BSSID from vdev_id 0
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All configuration sequences should be protected
with conf_mutex to avoid concurrent/conflicting
requests.
This should make sure that wep tx key setup is not
performed while hw is restarted (at least).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes sure no further tx requests are
submitted to HTT before driver teardown.
This should prevent invalid pointer/NULL
dereference on htt tx pool in ath10k_htt_tx() in
some cases of heavy traffic.
kvalo: remove the WARN_ON() if conf_mutex is held
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reduces risk of races and prepares for more
hw restart fixes.
It also makes sense to perform teardown after
mac80211 starts its restart routine as it
guarantees it has stopped itself by then
(including tx queues).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes failpath when override AC pdev param
setup fails and makes other pdev params setting
fail as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The channel_switch_beacon callback is optional, so it doesn't have to
be defined if it's not going to do anything useful with it. Both
ath9k and ath10k define the callback and just returns. This commit
removes them.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Verified that target's tx/rx chain register is set appropriately,
and that the tx rate goes down as number of chains
decrease, but I did not actually try to verify antenna
ceased to transmit when disabled.
kvalo: move ar->supp_*_chainmask initialisation to ath10k_mac_register()
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix sending and receiveing protected managment frames.
Lack of protected flag for received protected action frames
causes report these frames as unprotected robust action frames.
If the driver in AP mode sent frame with protected flag and
CCMP header using IEEE80211_KEY_FLAG_SW_MGMT_TX flag,
the FW encrypted frames once again. From user side all
received SA Query Requests and Responses were skipped and
all protected action frames were sent as malformed packets.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Beacon data wasn't properly cleared during early
phase of recovery. This in turn caused firmware to
crash because the beacon data was submitted before
vdevs were fully re-configured. Ultimately the
device was considered wedged and nothing worked
until driver was reloaded.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If for some reason mac80211 wouldn't stop
beaconing gracefully and just removed interface of
a running AP/IBSS interface it was possible to
leak pending beacon DMA mapping. It's very
unlikely but better safe than sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If 20MHz CAC completed successfully then
subsequent CAC with wider bandwidth (40Mhz, 80Mhz)
with identical control frequency did not start
monitor vdev making it impossible to detect any
radar pulses during intended CAC.
It also was incorrect to assume ath10k_config() will
be called after CAC is finished. Theoretically for
non-HT channels nothing changes between CAC and
start_ap() (albeit in practice this can be
different). The incorrect assumption led to CAC
not being stopped on non-HT chandefs leading to
all Rx being drooped making it impossible for
clients to associate.
While at it clean up the code a bit.
kvalo: separate WARN_ON() from the if statement
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is done to avoid forward declarations with
upcomming patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will allow the low level driver to make decision based
on the vif such as queues etc...
Since the vif might be NULL, we can't add it to the tracing
functions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix staging rtl8821ae driver]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible to create/delete/start/stop
monitor vdev from a few places that were not
exclusively protected against each other. This
resulted in monitor vdev being stopped/removed by
one call origin while another one was expecting it
to continue running.
For example if CAC was started and interface's
promiscuous mode was toggled monitor vdev was
removed from the driver meaning no radar would be
detected. In additional a warning would be printed
upon CAC completion complaining it tried to stop
non-running monitor vdev.
The patch simplifies monitor code by removing
IEEE80211_HW_WANT_MONITOR_VIF (which wasn't really
ever needed) and improves state tracking. It also
unifies prints.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
