This patch adds polling mode support for i2c-s3c2410 driver.The
SATA PHY controller's CMU and TRSV block's are of I2C register
map in exynos5250.These blocks can be configured using i2c.
But i2c controller instance on which these block's sits lacks an
interrupt line.Also the current i2c-s3c2410 driver is only interrupt
driven, thus a polling mode support is required in the driver for
supporting this controller. This patch adds this support to the driver.
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a reset GPIO support is specified, request the GPIO and get the chip
out of reset at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested with a r7s72100 genmai board acessing an eeprom.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Commit 89ce376c6b (drivers/net: Use of_match_ptr() macro in smc91x.c)
added minimal device tree support to smc91x, but it's not working on
many platforms because of the lack of some key configuration bits.
Fix the issue by parsing the necessary configuration like the
smc911x driver is doing. As most smc91x users seem to use 16-bit
access, let's default to that if no reg-io-width is specified.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When booted with device tree, we may still have platform data passed
as auxdata. For am3517 this is needed for passing the interrupt_enable
and interrupt_disable callbacks that access the omap system control module
registers. These callback functions will eventually go away when we have
a separate system control module driver.
Some of the things that are currently passed as platform data we don't need
to set up as device tree properties as they are always the same on am3517.
So let's use a new compatible flag for those so we can get those from
the device tree match data.
Also note that we need to fix setting of phy_dev to NULL instead of an empty
string as the code later on uses that to find the first phy on the mdio bus.
This seems to have been caused by 5d69e0076a (net: davinci_emac: switch to
new mdio).
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from board
files to DT. Tony thinks this was the last major set of fixes, with
maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed PCIe
hardware, i.e. incorrect number of busses on some SoCs, etc. The line
delta adds up due to various ranges moving around when this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in my
test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91, a couple
of reverts for ux500, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PljB
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from
board files to DT. Tony thinks this was the last major set of
fixes, with maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed
PCIe hardware, i.e. incorrect number of busses on some SoCs, etc.
The line delta adds up due to various ranges moving around when
this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in
my test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91,
a couple of reverts for ux500, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk
arm: socfpga: Enable ARM_TWD for socfpga
ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
ARM: multi_v7_defconfig: enable network for BeagleBone Black
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
...
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
re-format and re-word the device tree binding documentation for MPC8xxx
and compatibles, reference the common document for interrupt controllers
and remove outdated duplicate SoC specific information
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <Pawel.Moll@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <devicetree@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This binding shouldn't exist; Tegra20 has two forms of SPI controller
that are documented separately in nvidia,tegra20-sflash.txt and
nvidia,tegra20-slink.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This patch fix typo of property name from 'pullup-uV' to 'pullup-uv'.
The ntc_thermistor.c use 'pullup-uv' when parsing dt data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Adding Global Mixed-mode Technology Inc. to the list
of devicetree vendor prefixes.
Signed-off-by: Wei Ni <wni@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
phy-supply is an optional property of the fec driver, so add it to the binding
documentation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The binding and support for omap5-mpu which has a cortex-a15
smp core, gic and integrated L2 cache has been existing for sometime.
So Documenting the missing binding here.
Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Some features can be configured by the companion I2C chips,
which may not be available at the probe time. Fix the issue
by returning -EPROBE_DEFER when the MMC controller slots
are not configured.
While at it, let's also add minimal device tree support so
omap24xx platforms can use this driver without legacy mode
since we claim to support device tree for mach-omap2 based
systems.
Although adding the minimal device tree support is not strictly
a fix, it does remove one of the last blockers for dropping a
bunch of legacy platform data for mach-omap2.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on OMAP,
finding new breakage of things that don't work quite right yet without
the traditional board files. I expect a bit more of this to come in this
release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec work and
to stop the MCPM core to produce a warning (the warning was new to 3.13-rc1).
- A handful of minor fixes for various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zdhe
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on
OMAP, finding new breakage of things that don't work quite right
yet without the traditional board files. I expect a bit more of
this to come in this release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec
work and to stop the MCPM core to produce a warning (the warning
was new to 3.13-rc1).
- A handful of minor fixes for various platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm2835: add missing #xxx-cells to I2C nodes
ARM: dts: Add max77686 RTC interrupt to cros5250-common
ARM: vexpress/TC2: Implement MCPM power_down_finish()
ARM: tegra: Provide dummy powergate implementation
ARM: omap: fix warning with LPAE build
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: imx6qdl: disable spdif "rxtx5" clock option
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Pull crypto update from Herbert Xu:
- Made x86 ablk_helper generic for ARM
- Phase out chainiv in favour of eseqiv (affects IPsec)
- Fixed aes-cbc IV corruption on s390
- Added constant-time crypto_memneq which replaces memcmp
- Fixed aes-ctr in omap-aes
- Added OMAP3 ROM RNG support
- Add PRNG support for MSM SoC's
- Add and use Job Ring API in caam
- Misc fixes
[ NOTE! This pull request was sent within the merge window, but Herbert
has some questionable email sending setup that makes him public enemy
#1 as far as gmail is concerned. So most of his emails seem to be
trapped by gmail as spam, resulting in me not seeing them. - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (49 commits)
crypto: s390 - Fix aes-cbc IV corruption
crypto: omap-aes - Fix CTR mode counter length
crypto: omap-sham - Add missing modalias
padata: make the sequence counter an atomic_t
crypto: caam - Modify the interface layers to use JR API's
crypto: caam - Add API's to allocate/free Job Rings
crypto: caam - Add Platform driver for Job Ring
hwrng: msm - Add PRNG support for MSM SoC's
ARM: DT: msm: Add Qualcomm's PRNG driver binding document
crypto: skcipher - Use eseqiv even on UP machines
crypto: talitos - Simplify key parsing
crypto: picoxcell - Simplify and harden key parsing
crypto: ixp4xx - Simplify and harden key parsing
crypto: authencesn - Simplify key parsing
crypto: authenc - Export key parsing helper function
crypto: mv_cesa: remove deprecated IRQF_DISABLED
hwrng: OMAP3 ROM Random Number Generator support
crypto: sha256_ssse3 - also test for BMI2
crypto: mv_cesa - Remove redundant of_match_ptr
crypto: sahara - Remove redundant of_match_ptr
...
acpi_power_meter: Fix return value check from call to acpi_bus_get_device
nct6775: Fix/improve NCT6791 support
lm75: Add support for GMT G751
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ObF6
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- acpi_power_meter: Fix return value check from call to
acpi_bus_get_device
- nct6775: Fix/improve NCT6791 support
- lm75: Add support for GMT G751
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (acpi_power_meter) Fix acpi_bus_get_device() return value check
hwmon: (nct6775) NCT6791 supports weight control only for CPUFAN
hwmon: (nct6775) Monitor additional temperature registers
hwmon: (lm75) Add support for GMT G751 chip
Pull security subsystem updates from James Morris:
"In this patchset, we finally get an SELinux update, with Paul Moore
taking over as maintainer of that code.
Also a significant update for the Keys subsystem, as well as
maintenance updates to Smack, IMA, TPM, and Apparmor"
and since I wanted to know more about the updates to key handling,
here's the explanation from David Howells on that:
"Okay. There are a number of separate bits. I'll go over the big bits
and the odd important other bit, most of the smaller bits are just
fixes and cleanups. If you want the small bits accounting for, I can
do that too.
(1) Keyring capacity expansion.
KEYS: Consolidate the concept of an 'index key' for key access
KEYS: Introduce a search context structure
KEYS: Search for auth-key by name rather than target key ID
Add a generic associative array implementation.
KEYS: Expand the capacity of a keyring
Several of the patches are providing an expansion of the capacity of a
keyring. Currently, the maximum size of a keyring payload is one page.
Subtract a small header and then divide up into pointers, that only gives
you ~500 pointers on an x86_64 box. However, since the NFS idmapper uses
a keyring to store ID mapping data, that has proven to be insufficient to
the cause.
Whatever data structure I use to handle the keyring payload, it can only
store pointers to keys, not the keys themselves because several keyrings
may point to a single key. This precludes inserting, say, and rb_node
struct into the key struct for this purpose.
I could make an rbtree of records such that each record has an rb_node
and a key pointer, but that would use four words of space per key stored
in the keyring. It would, however, be able to use much existing code.
I selected instead a non-rebalancing radix-tree type approach as that
could have a better space-used/key-pointer ratio. I could have used the
radix tree implementation that we already have and insert keys into it by
their serial numbers, but that means any sort of search must iterate over
the whole radix tree. Further, its nodes are a bit on the capacious side
for what I want - especially given that key serial numbers are randomly
allocated, thus leaving a lot of empty space in the tree.
So what I have is an associative array that internally is a radix-tree
with 16 pointers per node where the index key is constructed from the key
type pointer and the key description. This means that an exact lookup by
type+description is very fast as this tells us how to navigate directly to
the target key.
I made the data structure general in lib/assoc_array.c as far as it is
concerned, its index key is just a sequence of bits that leads to a
pointer. It's possible that someone else will be able to make use of it
also. FS-Cache might, for example.
(2) Mark keys as 'trusted' and keyrings as 'trusted only'.
KEYS: verify a certificate is signed by a 'trusted' key
KEYS: Make the system 'trusted' keyring viewable by userspace
KEYS: Add a 'trusted' flag and a 'trusted only' flag
KEYS: Separate the kernel signature checking keyring from module signing
These patches allow keys carrying asymmetric public keys to be marked as
being 'trusted' and allow keyrings to be marked as only permitting the
addition or linkage of trusted keys.
Keys loaded from hardware during kernel boot or compiled into the kernel
during build are marked as being trusted automatically. New keys can be
loaded at runtime with add_key(). They are checked against the system
keyring contents and if their signatures can be validated with keys that
are already marked trusted, then they are marked trusted also and can
thus be added into the master keyring.
Patches from Mimi Zohar make this usable with the IMA keyrings also.
(3) Remove the date checks on the key used to validate a module signature.
X.509: Remove certificate date checks
It's not reasonable to reject a signature just because the key that it was
generated with is no longer valid datewise - especially if the kernel
hasn't yet managed to set the system clock when the first module is
loaded - so just remove those checks.
(4) Make it simpler to deal with additional X.509 being loaded into the kernel.
KEYS: Load *.x509 files into kernel keyring
KEYS: Have make canonicalise the paths of the X.509 certs better to deduplicate
The builder of the kernel now just places files with the extension ".x509"
into the kernel source or build trees and they're concatenated by the
kernel build and stuffed into the appropriate section.
(5) Add support for userspace kerberos to use keyrings.
KEYS: Add per-user_namespace registers for persistent per-UID kerberos caches
KEYS: Implement a big key type that can save to tmpfs
Fedora went to, by default, storing kerberos tickets and tokens in tmpfs.
We looked at storing it in keyrings instead as that confers certain
advantages such as tickets being automatically deleted after a certain
amount of time and the ability for the kernel to get at these tokens more
easily.
To make this work, two things were needed:
(a) A way for the tickets to persist beyond the lifetime of all a user's
sessions so that cron-driven processes can still use them.
The problem is that a user's session keyrings are deleted when the
session that spawned them logs out and the user's user keyring is
deleted when the UID is deleted (typically when the last log out
happens), so neither of these places is suitable.
I've added a system keyring into which a 'persistent' keyring is
created for each UID on request. Each time a user requests their
persistent keyring, the expiry time on it is set anew. If the user
doesn't ask for it for, say, three days, the keyring is automatically
expired and garbage collected using the existing gc. All the kerberos
tokens it held are then also gc'd.
(b) A key type that can hold really big tickets (up to 1MB in size).
The problem is that Active Directory can return huge tickets with lots
of auxiliary data attached. We don't, however, want to eat up huge
tracts of unswappable kernel space for this, so if the ticket is
greater than a certain size, we create a swappable shmem file and dump
the contents in there and just live with the fact we then have an
inode and a dentry overhead. If the ticket is smaller than that, we
slap it in a kmalloc()'d buffer"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (121 commits)
KEYS: Fix keyring content gc scanner
KEYS: Fix error handling in big_key instantiation
KEYS: Fix UID check in keyctl_get_persistent()
KEYS: The RSA public key algorithm needs to select MPILIB
ima: define '_ima' as a builtin 'trusted' keyring
ima: extend the measurement list to include the file signature
kernel/system_certificate.S: use real contents instead of macro GLOBAL()
KEYS: fix error return code in big_key_instantiate()
KEYS: Fix keyring quota misaccounting on key replacement and unlink
KEYS: Fix a race between negating a key and reading the error set
KEYS: Make BIG_KEYS boolean
apparmor: remove the "task" arg from may_change_ptraced_domain()
apparmor: remove parent task info from audit logging
apparmor: remove tsk field from the apparmor_audit_struct
apparmor: fix capability to not use the current task, during reporting
Smack: Ptrace access check mode
ima: provide hash algo info in the xattr
ima: enable support for larger default filedata hash algorithms
ima: define kernel parameter 'ima_template=' to change configured default
ima: add Kconfig default measurement list template
...
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
* Support for Perf from Mischa
* Enabling GPIO/Pinctrl drivers for Abilis TB10x platform
* New defconfig for buildroot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zVRP
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.13-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull second set of ARC changes from Vineet Gupta:
- Support for Perf from Mischa
- Enabling GPIO/Pinctrl drivers for Abilis TB10x platform
- New defconfig for buildroot
* tag 'arc-v3.13-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-arcfpga] Add defconfig without initramfs location
ARC: perf: ARC 700 PMU doesn't support sampling events
ARC: Add documentation on DT binding for ARC700 PMU
ARC: Add perf support for ARC700 cores
ARC: [TB10x] Updates for GPIO and pinctrl
Pull watchdog changes from Wim Van Sebroeck:
- addition of MOXA ART watchdog driver (moxart_wdt)
- addition of CSR SiRFprimaII and SiRFatlasVI watchdog driver
(sirfsoc_wdt)
- addition of ralink watchdog driver (rt2880_wdt)
- various fixes and cleanups (__user annotation, ioctl return codes,
removal of redundant of_match_ptr, removal of unnecessary
amba_set_drvdata(), use allocated buffer for usb_control_msg, ...)
- removal of MODULE_ALIAS_MISCDEV statements
- watchdog related DT bindings
- first set of improvements on the w83627hf_wdt driver
* git://www.linux-watchdog.org/linux-watchdog: (26 commits)
watchdog: w83627hf: Use helper functions to access superio registers
watchdog: w83627hf: Enable watchdog device only if not already enabled
watchdog: w83627hf: Enable watchdog only once
watchdog: w83627hf: Convert to watchdog infrastructure
watchdog: omap_wdt: raw read and write endian fix
watchdog: sirf: don't depend on dummy value of CLOCK_TICK_RATE
watchdog: pcwd_usb: overflow in usb_pcwd_send_command()
watchdog: rt2880_wdt: fix return value check in rt288x_wdt_probe()
watchdog: watchdog_core: Fix a trivial typo
watchdog: dw: Enable OF support for DW watchdog timer
watchdog: Get rid of MODULE_ALIAS_MISCDEV statements
watchdog: ts72xx_wdt: Propagate return value from timeout_to_regval
watchdog: pcwd_usb: Use allocated buffer for usb_control_msg
watchdog: sp805_wdt: Remove unnecessary amba_set_drvdata()
watchdog: sirf: add watchdog driver of CSR SiRFprimaII and SiRFatlasVI
watchdog: Remove redundant of_match_ptr
watchdog: ts72xx_wdt: cleanup return codes in ioctl
documentation/devicetree: Move DT bindings from gpio to watchdog
watchdog: add ralink watchdog driver
watchdog: Add MOXA ART watchdog driver
...
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=rT+j
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Highlights:
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups"
* tag 'for-v3.13' of git://git.infradead.org/battery-2.6:
pm2301-charger: Remove unneeded NULL checks
twl4030_charger: Add devicetree support
power_supply: Fix documentation for TEMP_*ALERT* properties
max17042_battery: Support regmap to access device's registers
max17042_battery: Use SIMPLE_DEV_PM_OPS
charger-manager : Replace kzalloc to devm_kzalloc and remove uneccessary code
bq2415x_charger: Fix max battery regulation voltage
tps65090-charger: Use "IS_ENABLED(CONFIG_OF)" for DT code
tps65090-charger: Drop devm_free_irq of devm_ allocated irq
power_supply: Add support for bq24735 charger
pm2301-charger: Staticize pm2xxx_charger_die_therm_mngt
pm2301-charger: Check return value of regulator_enable
ab8500-charger: Remove redundant break
ab8500-charger: Check return value of regulator_enable
isp1704_charger: Fix driver to work with changes introduced in v3.5
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Highlights:
* Support for Calxeda ECX-2000 memory controller, from Robert Richter
* Misc Calxeda Highbank drivers and EDAC core cleanups, from Rob Herring
and Robert Richter
* New maintainer for Freescale's MPC85xx EDAC driver: Johannes Thumshirn
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=pU/h
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"Following up on last week's discussion, here's my part of the EDAC
pile, highlights in the signed tag.
The last two patches have a date from just now because I've just
applied them to the tree after Johannes sent them to me earlier. I
decided to forward them now because they're trivial.
There's a third one for MPC85xx which adds PCIe error interrupt
support but since it is not so trivial and hasn't seen any linux-next
time, I'm deferring it to 3.14
EDAC update highlights:
- Support for Calxeda ECX-2000 memory controller, from Robert Richter
- Misc Calxeda Highbank drivers and EDAC core cleanups, from Rob
Herring and Robert Richter
- New maintainer for Freescale's MPC85xx EDAC driver: Johannes
Thumshirn"
* tag 'edac_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
edac/85xx: Remove mpc85xx_pci_err_remove
EDAC: Add edac-mpc85xx driver to MAINTAINERS
edac, highbank: Moving error injection to sysfs for edac
edac, highbank: Add MAINTAINERS entry
edac: Unify reporting of device info for device, mc and pci
edac, highbank: Improve and unify naming
edac, highbank: Add Calxeda ECX-2000 support
ARM: dts: calxeda: move memory-controller node out of ecx-common.dtsi
edac, highbank: Fix interrupt setup of mem and l2 controller
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=JDGc
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.13:
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield"
* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
mmc: wbsd: Silence compiler warning
mmc: core: Silence compiler warning in __mmc_switch
mmc: sh_mmcif: Convert to clk_prepare|unprepare
mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
mmc: dw_mmc: exynos: Revert the sdr_timing assignment
mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
mmc: Don't force card to active state when entering suspend/shutdown
MIPS: db1235: Don't use MMC_CLKGATE
mmc: core: Remove deprecated mmc_suspend|resume_host APIs
mmc: mmci: Move away from using deprecated APIs
mmc: via-sdmmc: Move away from using deprecated APIs
mmc: tmio: Move away from using deprecated APIs
mmc: sh_mmcif: Move away from using deprecated APIs
mmc: sdricoh_cs: Move away from using deprecated APIs
mmc: rtsx: Remove redundant suspend and resume callbacks
mmc: wbsd: Move away from using deprecated APIs
mmc: pxamci: Remove redundant suspend and resume callbacks
...
This was tested on a NETGEAR ReadyNAS 2120 device (Marvell Armada XP
based board, via DT).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On CSR SiRFprimaII and SiRFatlasVI, the 6th timer can act as a watchdog
timer when the Watchdog mode is enabled.
watchdog occur when TIMER watchdog counter matches the value software
pre-set, when this event occurs, the effect is the same as the system
software reset.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Romain Izard <romain.izard.pro@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I accidently put the devicetree bindings for the MEN A21 watchdog driver in
Documentation/devicetree/bindings/gpio instead of
Documentation/devicetree/bindings/watchdog, this patch addresses this error.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Rob Landley <rob@landley.net>
This patch adds a watchdog driver for the main hardware watchdog timer
found on MOXA ART SoCs.
The MOXA ART SoC provides one writable timer register, restarting
the hardware once it reaches zero. The register is auto decremented
every APB clock cycle.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A first set of batches of fixes for 3.13. The diffstat is large mostly
because we're adding a defconfig for a family that's been lacking it, and
there's some missing clock information added for i.MX and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix possible
hangs due to pending wakeup interrupts coming in during early boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0oVK
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A first set of batches of fixes for 3.13. The diffstat is large
mostly because we're adding a defconfig for a family that's been
lacking it, and there's some missing clock information added for i.MX
and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix
possible hangs due to pending wakeup interrupts coming in during early
boot"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: at91: fix hanged boot due to early rtt-interrupt
ARM: at91: fix hanged boot due to early rtc-interrupt
video: exynos_mipi_dsim: Remove unused variable
ARM: highbank: only select errata 764369 if SMP
ARM: sti: only select errata 764369 if SMP
ARM: tegra: init fuse before setting reset handler
ARM: vt8500: add defconfig for v6/v7 chips
ARM: integrator_cp: Set LCD{0,1} enable lines when turning on CLCD
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
MAINTAINERS: drop discontinued mailing list
ARM: dts: i.MX51: Fix OTG PHY clock
ARM: imx: set up pllv3 POWER and BYPASS sequentially
ARM: imx: pllv3 needs relock in .set_rate() call
...
Mostly bug fixes and clean up. There is a new driver, which is actually
moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree support
in the pwm-backlight driver. Backlights can now additionally be powered
using a regulator and enabled using a GPIO in addition to just the PWM
input.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=CB+z
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Mostly bug fixes and clean up. There is a new driver, which is
actually moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree
support in the pwm-backlight driver. Backlights can now additionally
be powered using a regulator and enabled using a GPIO in addition to
just the PWM input"
* tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
Documentation/pwm: Update supported SoC name for pwm-samsung
pwm: samsung: Fix kernel warning while unexporting a channel
MAINTAINERS: Move PWM subsystem tree to kernel.org
Documentation/pwm: Fix trivial typos
pwm-backlight: Remove unused variable
pwm_backlight: avoid short blank screen while doing hibernation
pwm-backlight: Fix brightness adjustment
pwm: add ep93xx PWM support
pwm-backlight: Allow for non-increasing brightness levels
pwm-backlight: Add power supply support
pwm-backlight: Use new enable_gpio field
unicore32: Initialize PWM backlight enable_gpio field
ARM: shmobile: Initialize PWM backlight enable_gpio field
ARM: SAMSUNG: Initialize PWM backlight enable_gpio field
ARM: pxa: Initialize PWM backlight enable_gpio field
ARM: OMAP: Initialize PWM backlight enable_gpio field
pwm-backlight: Add optional enable GPIO
pwm-backlight: Track enable state
pwm-backlight: Refactor backlight power on/off
pwm-backlight: Improve readability
...
Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. You will get an new drivers for
Hyper-V synthetic keyboard and for Neonode zForce touchscreens, plus a
bunch of driver fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (49 commits)
Revert "Input: ALPS - add support for model found on Dell XT2"
arm: dts: am335x sk: add touchscreen support
Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding
Input: cyttsp4 - replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
Input: mma8450 - add missing i2c_set_clientdata() in mma8450_probe()
Input: mpu3050 - add missing i2c_set_clientdata() in mpu3050_probe()
Input: tnetv107x-keypad - make irqs signed for error handling
Input: add driver for Neonode zForce based touchscreens
Input: sh_keysc - enable the driver on all ARM platforms
Input: remove a redundant max() call
Input: mousedev - allow disabling even without CONFIG_EXPERT
Input: allow deselecting serio drivers even without CONFIG_EXPERT
Input: i8042 - add PNP modaliases
Input: evdev - fall back to vmalloc for client event buffer
Input: cypress_ps2 - do not consider data bad if palm is detected
Input: cypress_ps2 - remove useless cast
Input: fix PWM-related undefined reference errors
Input: ALPS - change secondary device's name
Input: wacom - not all multi-interface devices support touch
Input: nspire-keypad - add missing clk_disable_unprepare() on error path
...
AS3722 PMIC and for STMicroelectronics STw481x PMIC.
Although this is a smaller update than usual, we also have:
- Device tree support for the max77693 driver.
- linux/of.h inclusion for all DT compatible MFD drivers, to avoid build
breakage in the future.
- Support for Intel Wildcat Point-LP PCH through the lpc_ich driver.
- A small arizona update for new wm5110 DSP registers and a few fixes.
- A small palmas update as well, including an of_device table addition
and a few minor fixes.
- Two small mfd-core changes, one including a memory leak fix for when
mfd_add_device() fails.
- Our usual round of minor cleanups and janitorial fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=nQ/p
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD updates from Samuel Ortiz:
"For the 3.13 merge window we have a couple of new drivers for the AMS
AS3722 PMIC and for STMicroelectronics STw481x PMIC.
Although this is a smaller update than usual, we also have:
- Device tree support for the max77693 driver
- linux/of.h inclusion for all DT compatible MFD drivers, to avoid
build breakage in the future
- Support for Intel Wildcat Point-LP PCH through the lpc_ich driver
- A small arizona update for new wm5110 DSP registers and a few fixes
- A small palmas update as well, including an of_device table
addition and a few minor fixes
- Two small mfd-core changes, one including a memory leak fix for
when mfd_add_device() fails
- Our usual round of minor cleanups and janitorial fixes"
* tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (63 commits)
Documentation: mfd: Update s2mps11.txt
mfd: pm8921: Potential NULL dereference in pm8921_remove()
mfd: Fix memory leak in mfd_add_devices()
mfd: Stop setting refcounting pointers in original mfd_cell arrays
mfd: wm5110: Enable micd clamp functionality
mfd: lpc_ich: Add Device IDs for Intel Wildcat Point-LP PCH
mfd: max77693: Fix up bug of wrong interrupt number
mfd: as3722: Don't export the regmap config
mfd: twl6040: Remove obsolete cleanup for i2c clientdata
mfd: tps65910: Remove warning during dt node parsing
mfd: lpc_sch: Ignore resource conflicts when adding mfd cells
mfd: ti_am335x_tscadc: Avoid possible deadlock of reg_lock
mfd: syscon: Return -ENOSYS if CONFIG_MFD_SYSCON is not enabled
mfd: Add support for ams AS3722 PMIC
mfd: max77693: Include linux/of.h header
mfd: tc3589x: Detect the precise version
mfd: omap-usb: prepare/unprepare clock while enable/disable
mfd: max77686: Include linux/of.h header
mfd: max8907: Include linux/of.h header
mfd: max8997: Include linux/of.h header
...
Pull hwmon fixes and updates from Jean Delvare:
"All lm90 driver fixes and improvements"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation: dt: hwmon: Add OF document for LM90
hwmon: (lm90) Add power control
hwmon: (lm90) Add support for TI TMP451
hwmon: (lm90) Use enums for the indexes of temp8 and temp11
hwmon: (lm90) Add support to handle IRQ
hwmon: (lm90) Define status bits
hwmon: (lm90) Fix max6696 alarm handling
Introduce support for Broadcom Serial Controller (BSC) I2C bus found
in the Kona family of Mobile SoCs. FIFO hardware is utilized but only
standard mode (100kHz), fast mode (400kHz), fast mode plus (1MHz), and
I2C high-speed (3.4 MHz) bus speeds are supported.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
[wsa: fixed Kconfig sorting, squashed broken out patches into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As we claim to support device tree for mach-omap2, we
should have the necessary flags in the driver to make it
usable.
Cc: linux-i2c@vger.kernel.org
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add documentation for the generic OMAP DES crypto modul describing the device
tree bindings.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A new compatible property "ti,omap5-sham" is added to the omap-sham driver
recently to support SHA/MD5 for OMAP5,DRA7 and AM43XX. Documenting the
same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OF document for LM90 in Documentation/devicetree/.
[JD: Add this new file to the LM90 MAINTAINERS entry.]
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Correct the SPI node compatible property items to match example code and
match current DTS usage.
Signed-off-by: Eric Witcher <ewitcher@mindspring.com>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
