DM9000 revision B needs 1 ms delay after PHY power-on.
PHY must be powered on by writing 0 into register DM9000_GPR before
all other settings will change (see Davicom spec and example code).
Remember, that register DM9000_GPR was not changed by reset sequence.
Without this fix the FIFO is out of sync and sends wrong data after
sequence of "ifconfig ethX down ; ifconfig ethX up".
Signed-off-by: David S. Miller <davem@davemloft.net>
netem_skb_cb() does :
return (struct netem_skb_cb *)qdisc_skb_cb(skb)->data;
Unfortunatly struct qdisc_skb_cb data is not long word aligned, so
access to psched_time_t time_to_send uses a non aligned access.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/sfc/ethtool.c: In function ‘efx_ethtool_self_test’:
drivers/net/sfc/ethtool.c:613: warning: the frame size of 1200 bytes
is larger than 1024 bytes
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge multicast snooping feature periodically issues
IPv6 general multicast listener queries to sense the absence of a
listener.
For this, it uses :: as its source address - however RFC 2710 requires:
"To be valid, the Query message MUST come from a link-local IPv6 Source
Address". Current Linux kernel versions seem to follow this requirement
and ignore our bogus MLD queries.
With this commit a link local address from the bridge interface is being
used to issue the MLD query, resulting in other Linux devices which are
multicast listeners in the network to respond with a MLD response (which
was not the case before).
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Map the IPv6 header's destination multicast address to an ethernet
source address instead of the MLD queries multicast address.
For instance for a general MLD query (multicast address in the MLD query
set to ::), this would wrongly be mapped to 33:33:00:00:00:00, although
an MLD queries destination MAC should always be 33:33:00:00:00:01 which
matches the IPv6 header's multicast destination ff02::1.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the multicast bridge snooping support is not active for
link local multicast. I assume this has been done to leave
important multicast data untouched, like IPv6 Neighborhood Discovery.
In larger, bridged, local networks it could however be desirable to
optimize for instance local multicast audio/video streaming too.
With the transient flag in IPv6 multicast addresses we have an easy
way to optimize such multimedia traffic without tempering with the
high priority multicast data from well-known addresses.
This patch alters the multicast bridge snooping for IPv6, to take
effect for transient multicast addresses instead of non-link-local
addresses.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the missing IPv6 multicast address flag defines to
complement the already existing multicast address scope defines and to
be able to check these flags nicely in the future.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nsrcs number is 2 Byte wide, therefore we need to call ntohs()
before using it.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We actually want a pointer to the grec_nsrcr and not the following
field. Otherwise we can get very high values for *nsrcs as the first two
bytes of the IPv6 multicast address are being used instead, leading to
a failing pskb_may_pull() which results in MLDv2 reports not being
parsed.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The protocol type for IPv6 entries in the hash table for multicast
bridge snooping is falsely set to ETH_P_IP, marking it as an IPv4
address, instead of setting it to ETH_P_IPV6, which results in negative
look-ups in the hash table later.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/DMA-API-HOWTO.txt states:
"DMA transfers need to be synced properly in order for
the cpu and device to see the most uptodate and correct
copy of the DMA buffer."
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported and found by Johannes Stezenbach:
rt2800{pci,usb} do not report the Michael MIC in RXed frames, but do check
the Michael MIC in hardware. Therefore we have to report to mac80211 that the
received frame does not include the Michael MIC.
https://bugzilla.kernel.org/show_bug.cgi?id=16608
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast channel change fixes:
a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC
https://bugzilla.kernel.org/show_bug.cgi?id=27382
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a bug that undo_retrans is incorrectly decremented when undo_marker is
not set or undo_retrans is already 0. This happens when sender receives
more DSACK ACKs than packets retransmitted during the current
undo phase. This may also happen when sender receives DSACK after
the undo operation is completed or cancelled.
Fix another bug that undo_retrans is incorrectly incremented when
sender retransmits an skb and tcp_skb_pcount(skb) > 1 (TSO). This case
is rare but not impossible.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Eric W. Biederman <ebiederm@xmission.com>
In the beginning with batching unreg_list was a list that was used only
once in the lifetime of a network device (I think). Now we have calls
using the unreg_list that can happen multiple times in the life of a
network device like dev_deactivate and dev_close that are also using the
unreg_list. In addition in unregister_netdevice_queue we also do a
list_move because for devices like veth pairs it is possible that
unregister_netdevice_queue will be called multiple times.
So I think the change below to fix dev_deactivate which Eric D. missed
will fix this problem. Now to go test that.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5fa782c2f5 re-worked the
handling of unknown parameters. sctp_init_cause_fixed() can now
return -ENOSPC if there is not enough tailroom in the error
chunk skb. When this happens, the error header is not appended to
the error chunk. In that case, the payload of the unknown parameter
should not be appended either.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dcb_app protocol field is a __u32 however the 802.1Qaz
specification defines it as a 16 bit field. This patch brings
the structure inline with the spec making it a __u16.
CC: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman reported a lockdep splat in inet_twsk_deschedule()
This is caused by inet_twsk_purge(), run from process context,
and commit 575f4cd5a5 (net: Use rcu lookups in inet_twsk_purge.)
removed the BH disabling that was necessary.
Add the BH disabling but fine grained, right before calling
inet_twsk_deschedule(), instead of whole function.
With help from Linus Torvalds and Eric W. Biederman
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Pavel Emelyanov <xemul@openvz.org>
CC: Arnaldo Carvalho de Melo <acme@redhat.com>
CC: stable <stable@kernel.org> (# 2.6.33+)
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
net: deinit automatic LIST_HEAD
net: dont leave active on stack LIST_HEAD
net: provide default_advmss() methods to blackhole dst_ops
tg3: Restrict phy ioctl access
drivers/net: Call netif_carrier_off at the end of the probe
ixgbe: work around for DDP last buffer size
ixgbe: fix panic due to uninitialised pointer
e1000e: flush all writebacks before unload
e1000e: check down flag in tasks
isdn: hisax: Use l2headersize() instead of dup (and buggy) func.
arp_notify: unconditionally send gratuitous ARP for NETDEV_NOTIFY_PEERS.
cxgb4vf: Use defined Mailbox Timeout
cxgb4vf: Quiesce Virtual Interfaces on shutdown ...
cxgb4vf: Behave properly when CONFIG_DEBUG_FS isn't defined ...
cxgb4vf: Check driver parameters in the right place ...
pch_gbe: Fix the MAC Address load issue.
iwlwifi: Delete iwl3945_good_plcp_health.
net/can/softing: make CAN_SOFTING_CS depend on CAN_SOFTING
netfilter: nf_iterate: fix incorrect RCU usage
pch_gbe: Fix the issue that the receiving data is not normal.
...
Correct channel setting function must be used for AR2317.
When I tested ahb patch on bullet2 all seemed to work fine,
but it couldn't connect another host (using ibss for example).
During an analysis I observed that it's transmitting on another
channel. I looked into madwifi code and understood that
the problem is in channel setting function. So atheros RF2317 not
fully handled in the current ath5k version and must be patched.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
taken two RT35XX EDIMAX from DPO_RT3562_3592_3062_LinuxSTA_V2.4.1.1_20101217
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure MAYDAY_INITIAL_TIMEOUT is at least 2 jiffies long
workqueue, freezer: unify spelling of 'freeze' + 'able' to 'freezable'
workqueue: wake up a worker when a rescuer is leaving a gcwq
commit 9b5e383c11 (net: Introduce
unregister_netdevice_many()) left an active LIST_HEAD() in
rollback_registered(), with possible memory corruption.
Even if device is freed without touching its unreg_list (and therefore
touching the previous memory location holding LISTE_HEAD(single), better
close the bug for good, since its really subtle.
(Same fix for default_device_exit_batch() for completeness)
Reported-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Eric W. Biderman <ebiderman@xmission.com>
Tested-by: Eric W. Biderman <ebiderman@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Octavian Purdila <opurdila@ixiacom.com>
CC: stable <stable@kernel.org> [.33+]
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biderman and Michal Hocko reported various memory corruptions
that we suspected to be related to a LIST head located on stack, that
was manipulated after thread left function frame (and eventually exited,
so its stack was freed and reused).
Eric Dumazet suggested the problem was probably coming from commit
443457242b (net: factorize
sync-rcu call in unregister_netdevice_many)
This patch fixes __dev_close() and dev_close() to properly deinit their
respective LIST_HEAD(single) before exiting.
References: https://lkml.org/lkml/2011/2/16/304
References: https://lkml.org/lkml/2011/2/14/223
Reported-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Eric W. Biderman <ebiderman@xmission.com>
Tested-by: Eric W. Biderman <ebiderman@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0dbaee3b37 (net: Abstract default ADVMSS behind an
accessor.) introduced a possible crash in tcp_connect_init(), when
dst->default_advmss() is called from dst_metric_advmss()
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When list debugging is enabled, we aim to readably show list corruption
errors, and the basic list_add/list_del operations end up having extra
debugging code in them to do some basic validation of the list entries.
However, "list_del_init()" and "list_move[_tail]()" ended up avoiding
the debug code due to how they were written. This fixes that.
So the _next_ time we have list_move() problems with stale list entries,
we'll hopefully have an easier time finding them..
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add missing frac fb div flag for dce4+
drm/radeon/kms: do not reject X16 and Y16X16 floating-point formats on r300
drm/nouveau: fix suspend/resume on GPUs that don't have PM support
drm/nouveau: flips/flipd need to always set 'evict' for move_accel_cleanup()
drm/nv40: fix tiling-related setup for a number of chipsets
drm/nouveau: fix non-EDIDful native mode selection
drm/nouveau: Fix detection of DDC-based LVDS on DCB15 boards.
drm/nv04-nv40: Fix NULL dereference when we fail to find an LVDS native mode.
drm/nv10: Fix crash when allocating a BO larger than half the available VRAM.
Validate number of blocks in map and remove redundant variable.
Signed-off-by: Timo Warns <warns@pre-sense.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch re-enables UIE timer/polling emulation for rtc devices
that do not support alarm irqs.
CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Uwe pointed out that my alarm based UIE emulation is not sufficient
to replace the older timer/polling based UIE emulation on devices
where there is no alarm irq. This causes rtc devices without alarms
to return -EINVAL to UIE ioctls. The fix is to re-instate the old
timer/polling method for devices without alarm irqs.
This patch reverts the following commits:
042620a018 - Remove UIE emulation
1daeddd596 - Cleanup removed UIE emulation declaration
b5cc8ca1c9 - Remove Kconfig symbol for UIE emulation
The emulation mode will still need to be wired-in with a following
patch before it will work.
CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
On hardware that doesn't support alarm interrupts, rtc_alarm_irq_enable
could return without releasing the ops_lock mutex.
This was introduced in
aa0be0f (RTC: Propagate error handling via rtc_timer_enqueue properly)
This patch corrects the issue by only returning once the mutex is
released.
[john.stultz: Reworded the commit log]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
If management firmware is present and the device is down, the firmware
will assume control of the phy. If a phy access were allowed from the
host, it will collide with firmware phy accesses, resulting in
unpredictable behavior. This patch fixes the problem by disallowing phy
accesses during the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without calling of netif_carrier_off at the end of the probe the operstate
is unknown when the device is initially opened. By default the carrier is
on so when the device is opened and netif_carrier_on is called the link
watch event is not fired and operstate remains zero (unknown).
This patch fixes this behavior in forcedeth and r8169.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a double completion associated with error handling for RC QPs.
The sequence is:
- The do_rc_ack() routine fields an RNR nack and there are 0
rnr_retries configured on the QP.
- qib_error_qp() stops the pending timer
- qib_rc_send_complete() is called from sdma_complete()
- qib_rc_send_complete() starts the timer because the msb of the psn
just completed says an ack is needed.
- a bunch of flushes occur as ipoib posts WQEs to an error'ed QP
- rc_timeout() calls qib_restart_rc()
- qib_restart_rc() calls qib_send_complete() with a
IB_WC_RETRY_EXC_ERR on a wqe that has already been completed in the
past
The fix avoids starting the timer since another packet will never
arrive.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The flaw was in skipping the second byte in MAC header due to increasing
the pointer AND indexed access starting at '1'.
Signed-off-by: Joerg Marx <joerg.marx@secunet.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Assigning a socket in timewait state to skb->sk can trigger
kernel oops, e.g. in nfnetlink_log, which does:
if (skb->sk) {
read_lock_bh(&skb->sk->sk_callback_lock);
if (skb->sk->sk_socket && skb->sk->sk_socket->file) ...
in the timewait case, accessing sk->sk_callback_lock and sk->sk_socket
is invalid.
Either all of these spots will need to add a test for sk->sk_state != TCP_TIME_WAIT,
or xt_TPROXY must not assign a timewait socket to skb->sk.
This does the latter.
If a TW socket is found, assign the tproxy nfmark, but skip the skb->sk assignment,
thus mimicking behaviour of a '-m socket .. -j MARK/ACCEPT' re-routing rule.
The 'SYN to TW socket' case is left unchanged -- we try to redirect to the
listener socket.
Cc: Balazs Scheidler <bazsi@balabit.hu>
Cc: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Otherwise we fail to properly suspend/resume all of the emulated devices.
Something between 2.6.38-rc2 and rc3 appears to have exposed this
issue, but it's always been wrong not to do this.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
A HW limitation was recently discovered where the last buffer in a DDP offload
cannot be a full buffer size in length. Fix the issue with a work around by
adding another buffer with size = 1.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
