Andy Shevchenko says:
====================
enc28j60: messaging clean up and ACPI improvements
Most of the patches in the series dedicated to update messaging to use modern
APIs, such as netdev, with a benefit to distinguish devices, if more than one
installed on the system.
Besides that, patch 1 targeting ACPI enabled systems when MAC address provided
there via properties.
And few clean ups are included, such as:
- switching to module_spi_driver()
- converting to use ether_addr_copy() API
- converting to use SPDX
Since v2:
- cover letter is added
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix few indentation splats. No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amend comments in the code:
- adding periods to the multi-line comments
- fixing typos
- capitalize first word in the sentences
- etc
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug prints of network operations will look better if network
device name is printed. The benefit of that is a possibility to distinguish
the actual hardware when more than one is installed on the system.
Convert appropriate printk(KERN_DEBUG) to netdev_print(KERN_DEBUG, ndev).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug prints of hardware status and operations will look better
if SPI device name is printed. The benefit of that is a possibility
to distinguish the actual hardware when more than one is installed
on the system.
Convert appropriate printk(KERN_DEBUG) to dev_print(KERN_DEBUG, &spi->dev).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using open coded printk(KERN_<LEVEL>) switch the driver to use
dev_<level> macros.
Note, the device name will be printed in full, which is beneficial when
more than one card installed on the system.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ether_addr_copy() instead of memcpy() to copy the mac address.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate some boilerplate code by using module_spi_driver() instead of
->init() / ->exit(), moving the salient bits from ->init() into ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev_<level>() macros are used against SPI device, the driver's name
is printed as well. No need to duplicate this explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open coded netdev_<level>() macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->probe() and ->remove() stages can be easily debugged with
initcall_debug or function tracer. There is no need to repeat the same
explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the DT-specific of_get_mac_address() function with
device_get_mac_address, which works on both DT and ACPI platforms.
This change makes it easier to add ACPI support.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add show and configure network flow classification (NFC) methods
to the ethtool. Show the specifies Rx ntuple filters.
Configures receive network flow classification option or rules.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable the multi queues to receive.
Program the direction of packets to specified queues according
to the mode selected in the MRQC register.
Multiple receive queues defined by filters and RSS for 4 queues.
Enable/disable RSS hashing and also to enable multiple receive queues.
This patch will allow further ethtool support development.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are some new e1000e devices can only be woken up from D3 one time,
by plugging Ethernet cable. Subsequent cable plugging does set PME bit
correctly, but it still doesn't get woken up.
Since e1000e connects to the root complex directly, we rely on ACPI to
wake it up. In this case, the GPE from _PRW only works once and stops
working after that. Though it appears to be a platform bug, e1000e
maintainers confirmed that I219 does not support D3.
So disable runtime PM on CNP+ chips. We may need to disable earlier
generations if this bug also hit older platforms.
Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=280819
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are some lines that have indentation issues, fix these
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IPv4 has icmp_echo_ignore_broadcast to prevent responding to broadcast pings.
IPv6 needs a similar mechanism.
v1->v2:
- Remove NET_IPV6_ICMP_ECHO_IGNORE_MULTICAST.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb sets different WoL settings in system suspend callback and runtime
suspend callback.
The suspend direct complete optimization leaves igb in runtime suspended
state with wrong WoL setting during system suspend.
To fix this, we need to disable suspend direct complete optimization to
let igb always use suspend callback to set correct WoL during system
suspend.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to comments in <linux/netdevice.h> we should return either >0
or -errno from ->ndo_set_features() if changing dev->features by itself.
Return 1 in such places to notify netdev_update_features() about applied
changes in dev->features.
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix sparse warning:
drivers/net/ethernet/pasemi/pasemi_mac.c:1842:5: warning:
symbol 'pasemi_mac_init_module' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the request socket is created locally, it'd make more sense to
use reqsk_free() instead of reqsk_put() in TFO and syncookies' error
path.
However, tcp_get_cookie_sock() may set ->rsk_refcnt before freeing the
socket; tcp_conn_request() may also have non-null ->rsk_refcnt because
of tcp_try_fastopen(). In both cases 'req' hasn't been exposed
to the outside world and is safe to free immediately, but that'd
trigger the WARN_ON_ONCE in reqsk_free().
Define __reqsk_free() for these situations where we know nobody's
referencing the socket, even though ->rsk_refcnt might be non-null.
Now we can consolidate the error path of tcp_get_cookie_sock() and
tcp_conn_request().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
net/core/datagram.c:411:5: warning:
symbol '__skb_datagram_iter' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c:407:6:
warning: symbol 'hclgevf_update_link_mode' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/ibm/ibmveth.c:96:21:
warning: symbol 'ibmveth_stats' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP ipv6 fast path dereferences a pointer to get to the inet6
part of a tcp socket, but given the fixed memory placement,
we can do better and avoid a possible cache line miss.
This also reduces register pressure, since we let the compiler
know about this memory placement.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver currently reports a fixed value for both speed and
duplex settings regardless of the actual backing device that is being
used. By adding support to the QUERY_PHYS_PARMS command defined by the
PAPR+ we can query the current physical port state and report the proper
values for these feilds.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a multicast stream may start out using replicast, because
there are few destinations, and then it should ideally switch to
L2/broadcast IGMP/multicast when the number of destinations grows beyond
a certain limit. The opposite should happen when the number decreases
below the limit.
To eliminate the risk of message reordering caused by method change,
a sending socket must stick to a previously selected method until it
enters an idle period of 5 seconds. Means there is a 5 seconds pause
in the traffic from the sender socket.
If the sender never makes such a pause, the method will never change,
and transmission may become very inefficient as the cluster grows.
With this commit, we allow such a switch between replicast and
broadcast without any need for a traffic pause.
Solution is to send a dummy message with only the header, also with
the SYN bit set, via broadcast or replicast. For the data message,
the SYN bit is set and sending via replicast or broadcast (inverse
method with dummy).
Then, at receiving side any messages follow first SYN bit message
(data or dummy message), they will be held in deferred queue until
another pair (dummy or data message) arrived in other link.
v2: reverse christmas tree declaration
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for introducing a smooth switching between replicast
and broadcast method for multicast message, We have to introduce a new
capability flag TIPC_MCAST_RBCTL to handle this new feature.
During a cluster upgrade a node can come back with this new capabilities
which also must be reflected in the cluster capabilities field.
The new feature is only applicable if all node in the cluster supports
this new capability.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a multicast stream uses either broadcast or replicast as
transmission method, based on the ratio between number of actual
destinations nodes and cluster size.
However, when an L2 interface (e.g., VXLAN) provides pseudo
broadcast support, this becomes very inefficient, as it blindly
replicates multicast packets to all cluster/subnet nodes,
irrespective of whether they host actual target sockets or not.
The TIPC multicast algorithm is able to distinguish real destination
nodes from other nodes, and hence provides a smarter and more
efficient method for transferring multicast messages than
pseudo broadcast can do.
Because of this, we now make it possible for users to force
the broadcast link to permanently switch to using replicast,
irrespective of which capabilities the bearer provides,
or pretend to provide.
Conversely, we also make it possible to force the broadcast link
to always use true broadcast. While maybe less useful in
deployed systems, this may at least be useful for testing the
broadcast algorithm in small clusters.
We retain the current AUTOSELECT ability, i.e., to let the broadcast link
automatically select which algorithm to use, and to switch back and forth
between broadcast and replicast as the ratio between destination
node number and cluster size changes. This remains the default method.
Furthermore, we make it possible to configure the threshold ratio for
such switches. The default ratio is now set to 10%, down from 25% in the
earlier implementation.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an explanation of what is expected with respect to sending new
versions of specific patches within a patch series, as well as what
happens if an earlier patch series accidentally gets merged).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2019-03-18
please apply the following three patches to -net. The first two are fixes
for minor race conditions in the probe code, while the third one gets
dropwatch working (again).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the TX completion path, qeth_release_skbs() frees the completed
skbs with __skb_queue_purge(). This ends in kfree_skb(), reporting every
completed skb as dropped.
On the other hand when dropping an skb in .ndo_start_xmit, we end up
calling consume_skb()... where we should be using kfree_skb() so that
drop monitors get notified.
Switch the drop/consume logic around, and also don't accumulate dropped
packets in the tx_errors statistics.
Fixes: dc149e3764 ("s390/qeth: replace open-coded skb_queue_walk()")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ucast IP table is utilized by some of the L3-specific sysfs attributes
that qeth_l3_create_device_attributes() provides. So initialize the table
_before_ registering the attributes.
Fixes: ebccc7397e ("s390/qeth: add missing hash table initializations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW trap and VNICC configuration is exposed via sysfs, and may have
already been modified when qeth_l?_probe_device() attempts to initialize
them. So (1) initialize the VNICC values a little earlier, and (2) don't
bother about the HW trap mode, it was already initialized before.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device ID alone does not uniquely identify a device. Test both the
vendor and device ID to make sure we don't mistakenly think some other
vendor's 0xB410 device is a Digium HFC4S. Also, instead of the bare hex
ID, use the same constant (PCI_DEVICE_ID_DIGIUM_HFC4S) used in the device
ID table.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
sctp: fix ignoring asoc_id for tcp-style sockets on some setsockopts
This is a patchset to fix ignoring asoc_id for tcp-style sockets on
some setsockopts, introduced by SCTP_CURRENT_ASSOC of the patchset:
[net-next,00/24] sctp: support SCTP_FUTURE/CURRENT/ALL_ASSOC
(https://patchwork.ozlabs.org/cover/1031706/)
As Marcelo suggested, we fix it on each setsockopt that is using
SCTP_CURRENT_ASSOC one by one by adding the check:
if (sctp_style(sk, TCP))
xxx.xxx_assoc_id = SCTP_FUTURE_ASSOC;
so that assoc_id will be completely ingored for tcp-style socket on
setsockopts, and works as SCTP_FUTURE_ASSOC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_STREAM_SCHEDULER sockopt.
Fixes: 7efba10d6b ("sctp: add SCTP_FUTURE_ASOC and SCTP_CURRENT_ASSOC for SCTP_STREAM_SCHEDULER sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_EVENT sockopt.
Fixes: d251f05e3b ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_EVENT sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_ENABLE_STREAM_RESET sockopt.
Fixes: 99a62135e1 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_ENABLE_STREAM_RESET sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_DEFAULT_PRINFO sockopt.
Fixes: 3a583059d1 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_DEFAULT_PRINFO sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_DEACTIVATE_KEY sockopt.
Fixes: 2af66ff3ed ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_DEACTIVATE_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_DELETE_KEY sockopt.
Fixes: 3adcc30060 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_DELETE_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_ACTIVE_KEY sockopt.
Fixes: bf9fb6ad4f ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_ACTIVE_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_KEY sockopt.
Fixes: 7fb3be13a2 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_MAX_BURST sockopt.
Fixes: e0651a0dc8 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_MAX_BURST sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_CONTEXT sockopt.
Fixes: 49b037acca ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_CONTEXT sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
