During the nocow writeback path, we currently iterate the rbtree of block
groups twice: once for checking if the target block group is RO with the
call to btrfs_extent_readonly()), and once again for getting a nocow
reference on the block group with a call to btrfs_inc_nocow_writers().
Since btrfs_inc_nocow_writers() already returns false when the target
block group is RO, remove the call to btrfs_extent_readonly(). Not only
we avoid searching the blocks group rbtree twice, it also helps reduce
contention on the lock that protects it (specially since it is a spin
lock and not a read-write lock). That may make a noticeable difference
on very large filesystems, with thousands of allocated block groups.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When truncating a file, file buffers which have already been allocated
but not yet written may be truncated. Truncating these buffers could
cause breakage of a sequential write pattern in a block group if the
truncated blocks are for example followed by blocks allocated to another
file. To avoid this problem, always wait for write out of all unwritten
buffers before proceeding with the truncate execution.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If more than one IO is issued for one file extent, these IO can be
written to separate regions on a device. Since we cannot map one file
extent to such a separate area on a zoned filesystem, we need to follow
the "one IO == one ordered extent" rule.
The normal buffered, uncompressed and not pre-allocated write path (used
by cow_file_range()) sometimes does not follow this rule. It can write a
part of an ordered extent when specified a region to write e.g., when
its called from fdatasync().
Introduce a dedicated (uncompressed buffered) data write path for zoned
filesystems, that will COW the region and write it at once.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Likewise to buffered IO, enable zone append writing for direct IO when
its used on a zoned block device.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Enable zone append writing for zoned mode. When using zone append, a
bio is issued to the start of a target zone and the device decides to
place it inside the zone. Upon completion the device reports the actual
written position back to the host.
Three parts are necessary to enable zone append mode. First, modify the
bio to use REQ_OP_ZONE_APPEND in btrfs_submit_bio_hook() and adjust the
bi_sector to point the beginning of the zone.
Second, record the returned physical address (and disk/partno) to the
ordered extent in end_bio_extent_writepage() after the bio has been
completed. We cannot resolve the physical address to the logical address
because we can neither take locks nor allocate a buffer in this end_bio
context. So, we need to record the physical address to resolve it later
in btrfs_finish_ordered_io().
And finally, rewrite the logical addresses of the extent mapping and
checksum data according to the physical address using btrfs_rmap_block.
If the returned address matches the originally allocated address, we can
skip this rewriting process.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
To ensure that an ordered extent maps to a contiguous region on disk, we
need to maintain a "one bio == one ordered extent" rule.
Ensure that constructing bio does not span more than an ordered extent.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
For a zone append write, the device decides the location the data is being
written to. Therefore we cannot ensure that two bios are written
consecutively on the device. In order to ensure that an ordered extent
maps to a contiguous region on disk, we need to maintain a "one bio ==
one ordered extent" rule.
Implement splitting of an ordered extent and extent map on bio submission
to adhere to the rule.
extract_ordered_extent() hooks into btrfs_submit_data_bio() and splits the
corresponding ordered extent so that the ordered extent's region fits into
one bio and the corresponding device limits.
Several sanity checks need to be done in extract_ordered_extent() e.g.
- We cannot split once end_bio'd ordered extent because we cannot divide
ordered->bytes_left for the split ones
- We do not expect a compressed ordered extent
- We should not have checksum list because we omit the list splitting.
Since the function is called before btrfs_wq_submit_bio() or
btrfs_csum_one_bio(), this should be always ensured.
We also need to split an extent map by creating a new one. If not,
unpin_extent_cache() complains about the difference between the start of
the extent map and the file's logical offset.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Zoned filesystems use REQ_OP_ZONE_APPEND bios for writing to actual
devices.
Let btrfs_end_bio() and btrfs_op be aware of it, by mapping
REQ_OP_ZONE_APPEND to BTRFS_MAP_WRITE and using btrfs_op() instead of
bio_op().
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
To support subpage sector size, data also need extra info to make sure
which sectors in a page are uptodate/dirty/...
This patch will make pages for data inodes get btrfs_subpage structure
attached, and detached when the page is freed.
This patch also slightly changes the timing when
set_page_extent_mapped() is called to make sure:
- We have page->mapping set
page->mapping->host is used to grab btrfs_fs_info, thus we can only
call this function after page is mapped to an inode.
One call site attaches pages to inode manually, thus we have to modify
the timing of set_page_extent_mapped() a bit.
- As soon as possible, before other operations
Since memory allocation can fail, we have to do extra error handling.
Calling set_page_extent_mapped() as soon as possible can simply the
error handling for several call sites.
The idea is pretty much the same as iomap_page, but with more bitmaps
for btrfs specific cases.
Currently the plan is to switch iomap if iomap can provide sector
aligned write back (only write back dirty sectors, but not the full
page, data balance require this feature).
So we will stick to btrfs specific bitmap for now.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
PAGE_CLEAR_DIRTY and PAGE_SET_WRITEBACK are two defines used in
__process_pages_contig(), to let the function know to clear page dirty
bit and then set page writeback.
However page writeback and dirty bits are conflicting (at least for
sector size == PAGE_SIZE case), this means these two have to be always
updated together.
This means we can merge PAGE_CLEAR_DIRTY and PAGE_SET_WRITEBACK to
PAGE_START_WRITEBACK.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Before this change, the btrfs_get_io_geometry() function was calling
btrfs_get_chunk_map() to get the extent mapping, necessary for
calculating the I/O geometry. It was using that extent mapping only
internally and freeing the pointer after its execution.
That resulted in calling btrfs_get_chunk_map() de facto twice by the
__btrfs_map_block() function. It was calling btrfs_get_io_geometry()
first and then calling btrfs_get_chunk_map() directly to get the extent
mapping, used by the rest of the function.
Change that to passing the extent mapping to the btrfs_get_io_geometry()
function as an argument.
This could improve performance in some cases. For very large
filesystems, i.e. several thousands of allocated chunks, not only this
avoids searching two times the rbtree, saving time, it may also help
reducing contention on the lock that protects the tree - thinking of
writeback starting for multiple inodes, other tasks allocating or
removing chunks, and anything else that requires access to the rbtree.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Michal Rostecki <mrostecki@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add Filipe's analysis ]
Signed-off-by: David Sterba <dsterba@suse.com>
Commit dbfdb6d1b3 ("Btrfs: Search for all ordered extents that could
span across a page") make btrfs_invalidapage() to search all ordered
extents.
The offending code looks like this:
again:
start = page_start;
ordered = btrfs_lookup_ordered_range(inode, start, page_end - start + 1);
if (ordred) {
end = min(page_end,
ordered->file_offset + ordered->num_bytes - 1);
/* Do the cleanup */
start = end + 1;
if (start < page_end)
goto again;
}
The behavior is indeed necessary for the incoming subpage support, but
when it iterates through all the ordered extents, it also resets the
search range @start.
This means, for the following cases, we can double account the ordered
extents, causing its bytes_left underflow:
Page offset
0 16K 32K
|<--- OE 1 --->|<--- OE 2 ---->|
As the first iteration will find ordered extent (OE) 1, which doesn't
cover the full page, thus after cleanup code, we need to retry again.
But again label will reset start to page_start, and we got OE 1 again,
which causes double accounting on OE 1, and cause OE 1's byte_left to
underflow.
This problem can only happen for subpage case, as for regular sectorsize
== PAGE_SIZE case, we will always find a OE ends at or after page end,
thus no way to trigger the problem.
Move the again label after start = page_start. There will be more
comprehensive rework to convert the open coded loop to a proper while
loop for subpage support.
Fixes: dbfdb6d1b3 ("Btrfs: Search for all ordered extents that could span across a page")
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The comment for can_nocow_extent() says that the function will flush
ordered extents, however that never happens and was never true before the
comment was added in commit e4ecaf90bc ("btrfs: add comments for
btrfs_check_can_nocow() and can_nocow_extent()"). This is true only for
the function btrfs_check_can_nocow(), which after that commit was renamed
to check_can_nocow(). So just remove that part of the comment.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Fixes fs/btrfs/inode.c:3101: warning: Function parameter or member 'fs_info' not described in 'btrfs_wait_on_delayed_iputs'
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
There is a long existing bug in the last parameter of
btrfs_add_ordered_extent(), in commit 771ed689d2 ("Btrfs: Optimize
compressed writeback and reads") back to 2008.
In that ancient commit btrfs_add_ordered_extent() expects the @type
parameter to be one of the following:
- BTRFS_ORDERED_REGULAR
- BTRFS_ORDERED_NOCOW
- BTRFS_ORDERED_PREALLOC
- BTRFS_ORDERED_COMPRESSED
But we pass 0 in cow_file_range(), which means BTRFS_ORDERED_IO_DONE.
Ironically extra check in __btrfs_add_ordered_extent() won't set the bit
if we see (type == IO_DONE || type == IO_COMPLETE), and avoid any
obvious bug.
But this still leads to regular COW ordered extent having no bit to
indicate its type in various trace events, rendering REGULAR bit
useless.
[FIX]
Change the following aspects to avoid such problem:
- Reorder btrfs_ordered_extent::flags
Now the type bits go first (REGULAR/NOCOW/PREALLCO/COMPRESSED), then
DIRECT bit, finally extra status bits like IO_DONE/COMPLETE/IOERR.
- Add extra ASSERT() for btrfs_add_ordered_extent_*()
- Remove @type parameter for btrfs_add_ordered_extent_compress()
As the only valid @type here is BTRFS_ORDERED_COMPRESSED.
- Remove the unnecessary special check for IO_DONE/COMPLETE in
__btrfs_add_ordered_extent()
This is just to make the code work, with extra ASSERT(), there are
limited values can be passed in.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The refactoring involves the following modifications:
- Return bool instead of int
- Parameter update for @cached of btrfs_dec_test_first_ordered_pending()
For btrfs_dec_test_first_ordered_pending(), @cached is only used to
return the finished ordered extent.
Rename it to @finished_ret.
- Comment updates
* Change one stale comment
Which still refers to btrfs_dec_test_ordered_pending(), but the
context is calling btrfs_dec_test_first_ordered_pending().
* Follow the common comment style for both functions
Add more detailed descriptions for parameters and the return value
* Move the reason why test_and_set_bit() is used into the call sites
- Change how the return value is calculated
The most anti-human part of the return value is:
if (...)
ret = 1;
...
return ret == 0;
This means, when we set ret to 1, the function returns 0.
Change the local variable name to @finished, and directly return the
value of it.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Following the rework in e076ab2a2c ("btrfs: shrink delalloc pages
instead of full inodes") the nr variable is no longer passed by
reference to start_delalloc_inodes hence it cannot change. Additionally
we are always guaranteed for it to be positive number hence it's
redundant to have it as a condition in the loop. Simply remove that
usage.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's currently u64 which gets instantly translated either to LONG_MAX
(if U64_MAX is passed) or cast to an unsigned long (which is in fact,
wrong because writeback_control::nr_to_write is a signed, long type).
Just convert the function's argument to be long time which obviates the
need to manually convert u64 value to a long. Adjust all call sites
which pass U64_MAX to pass LONG_MAX. Finally ensure that in
shrink_delalloc the u64 is converted to a long without overflowing,
resulting in a negative number.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's no longer used. While at it also remove new_dirid in create_subvol
as it's used in a single place and open code it. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Adjust the way free_objectid is being initialized, it now stores
BTRFS_FIRST_FREE_OBJECTID rather than the, somewhat arbitrary,
BTRFS_FIRST_FREE_OBJECTID - 1. This change also has the added benefit
that now it becomes unnecessary to explicitly initialize free_objectid
for a newly create fs root.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This better reflects the semantics of the function i.e no search is
performed whatsoever.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Extend some inode methods with an additional user namespace argument. A
filesystem that is aware of idmapped mounts will receive the user
namespace the mount has been marked with. This can be used for
additional permission checking and also to enable filesystems to
translate between uids and gids if they need to. We have implemented all
relevant helpers in earlier patches.
As requested we simply extend the exisiting inode method instead of
introducing new ones. This is a little more code churn but it's mostly
mechanical and doesnt't leave us with additional inode methods.
Link: https://lore.kernel.org/r/20210121131959.646623-25-christian.brauner@ubuntu.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
The generic_fillattr() helper fills in the basic attributes associated
with an inode. Enable it to handle idmapped mounts. If the inode is
accessed through an idmapped mount map it into the mount's user
namespace before we store the uid and gid. If the initial user namespace
is passed nothing changes so non-idmapped mounts will see identical
behavior as before.
Link: https://lore.kernel.org/r/20210121131959.646623-12-christian.brauner@ubuntu.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Morris <jamorris@linux.microsoft.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
The posix acl permission checking helpers determine whether a caller is
privileged over an inode according to the acls associated with the
inode. Add helpers that make it possible to handle acls on idmapped
mounts.
The vfs and the filesystems targeted by this first iteration make use of
posix_acl_fix_xattr_from_user() and posix_acl_fix_xattr_to_user() to
translate basic posix access and default permissions such as the
ACL_USER and ACL_GROUP type according to the initial user namespace (or
the superblock's user namespace) to and from the caller's current user
namespace. Adapt these two helpers to handle idmapped mounts whereby we
either map from or into the mount's user namespace depending on in which
direction we're translating.
Similarly, cap_convert_nscap() is used by the vfs to translate user
namespace and non-user namespace aware filesystem capabilities from the
superblock's user namespace to the caller's user namespace. Enable it to
handle idmapped mounts by accounting for the mount's user namespace.
In addition the fileystems targeted in the first iteration of this patch
series make use of the posix_acl_chmod() and, posix_acl_update_mode()
helpers. Both helpers perform permission checks on the target inode. Let
them handle idmapped mounts. These two helpers are called when posix
acls are set by the respective filesystems to handle this case we extend
the ->set() method to take an additional user namespace argument to pass
the mount's user namespace down.
Link: https://lore.kernel.org/r/20210121131959.646623-9-christian.brauner@ubuntu.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
When file attributes are changed most filesystems rely on the
setattr_prepare(), setattr_copy(), and notify_change() helpers for
initialization and permission checking. Let them handle idmapped mounts.
If the inode is accessed through an idmapped mount map it into the
mount's user namespace. Afterwards the checks are identical to
non-idmapped mounts. If the initial user namespace is passed nothing
changes so non-idmapped mounts will see identical behavior as before.
Helpers that perform checks on the ia_uid and ia_gid fields in struct
iattr assume that ia_uid and ia_gid are intended values and have already
been mapped correctly at the userspace-kernelspace boundary as we
already do today. If the initial user namespace is passed nothing
changes so non-idmapped mounts will see identical behavior as before.
Link: https://lore.kernel.org/r/20210121131959.646623-8-christian.brauner@ubuntu.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
The inode_owner_or_capable() helper determines whether the caller is the
owner of the inode or is capable with respect to that inode. Allow it to
handle idmapped mounts. If the inode is accessed through an idmapped
mount it according to the mount's user namespace. Afterwards the checks
are identical to non-idmapped mounts. If the initial user namespace is
passed nothing changes so non-idmapped mounts will see identical
behavior as before.
Similarly, allow the inode_init_owner() helper to handle idmapped
mounts. It initializes a new inode on idmapped mounts by mapping the
fsuid and fsgid of the caller from the mount's user namespace. If the
initial user namespace is passed nothing changes so non-idmapped mounts
will see identical behavior as before.
Link: https://lore.kernel.org/r/20210121131959.646623-7-christian.brauner@ubuntu.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Morris <jamorris@linux.microsoft.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
The two helpers inode_permission() and generic_permission() are used by
the vfs to perform basic permission checking by verifying that the
caller is privileged over an inode. In order to handle idmapped mounts
we extend the two helpers with an additional user namespace argument.
On idmapped mounts the two helpers will make sure to map the inode
according to the mount's user namespace and then peform identical
permission checks to inode_permission() and generic_permission(). If the
initial user namespace is passed nothing changes so non-idmapped mounts
will see identical behavior as before.
Link: https://lore.kernel.org/r/20210121131959.646623-6-christian.brauner@ubuntu.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Morris <jamorris@linux.microsoft.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Commit 38d715f494 ("btrfs: use btrfs_start_delalloc_roots in
shrink_delalloc") cleaned up how we do delalloc shrinking by utilizing
some infrastructure we have in place to flush inodes that we use for
device replace and snapshot. However this introduced a pretty serious
performance regression. To reproduce the user untarred the source
tarball of Firefox (360MiB xz compressed/1.5GiB uncompressed), and would
see it take anywhere from 5 to 20 times as long to untar in 5.10
compared to 5.9. This was observed on fast devices (SSD and better) and
not on HDD.
The root cause is because before we would generally use the normal
writeback path to reclaim delalloc space, and for this we would provide
it with the number of pages we wanted to flush. The referenced commit
changed this to flush that many inodes, which drastically increased the
amount of space we were flushing in certain cases, which severely
affected performance.
We cannot revert this patch unfortunately because of 3d45f221ce
("btrfs: fix deadlock when cloning inline extent and low on free
metadata space") which requires the ability to skip flushing inodes that
are being cloned in certain scenarios, which means we need to keep using
our flushing infrastructure or risk re-introducing the deadlock.
Instead to fix this problem we can go back to providing
btrfs_start_delalloc_roots with a number of pages to flush, and then set
up a writeback_control and utilize sync_inode() to handle the flushing
for us. This gives us the same behavior we had prior to the fix, while
still allowing us to avoid the deadlock that was fixed by Filipe. I
redid the users original test and got the following results on one of
our test machines (256GiB of ram, 56 cores, 2TiB Intel NVMe drive)
5.9 0m54.258s
5.10 1m26.212s
5.10+patch 0m38.800s
5.10+patch is significantly faster than plain 5.9 because of my patch
series "Change data reservations to use the ticketing infra" which
contained the patch that introduced the regression, but generally
improved the overall ENOSPC flushing mechanisms.
Additional testing on consumer-grade SSD (8GiB ram, 8 CPU) confirm
the results:
5.10.5 4m00s
5.10.5+patch 1m08s
5.11-rc2 5m14s
5.11-rc2+patch 1m30s
Reported-by: René Rebe <rene@exactcode.de>
Fixes: 38d715f494 ("btrfs: use btrfs_start_delalloc_roots in shrink_delalloc")
CC: stable@vger.kernel.org # 5.10
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Tested-by: David Sterba <dsterba@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add my test results ]
Signed-off-by: David Sterba <dsterba@suse.com>
When cloning an inline extent there are cases where we can not just copy
the inline extent from the source range to the target range (e.g. when the
target range starts at an offset greater than zero). In such cases we copy
the inline extent's data into a page of the destination inode and then
dirty that page. However, after that we will need to start a transaction
for each processed extent and, if we are ever low on available metadata
space, we may need to flush existing delalloc for all dirty inodes in an
attempt to release metadata space - if that happens we may deadlock:
* the async reclaim task queued a delalloc work to flush delalloc for
the destination inode of the clone operation;
* the task executing that delalloc work gets blocked waiting for the
range with the dirty page to be unlocked, which is currently locked
by the task doing the clone operation;
* the async reclaim task blocks waiting for the delalloc work to complete;
* the cloning task is waiting on the waitqueue of its reservation ticket
while holding the range with the dirty page locked in the inode's
io_tree;
* if metadata space is not released by some other task (like delalloc for
some other inode completing for example), the clone task waits forever
and as a consequence the delalloc work and async reclaim tasks will hang
forever as well. Releasing more space on the other hand may require
starting a transaction, which will hang as well when trying to reserve
metadata space, resulting in a deadlock between all these tasks.
When this happens, traces like the following show up in dmesg/syslog:
[87452.323003] INFO: task kworker/u16:11:1810830 blocked for more than 120 seconds.
[87452.323644] Tainted: G B W 5.10.0-rc4-btrfs-next-73 #1
[87452.324248] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[87452.324852] task:kworker/u16:11 state:D stack: 0 pid:1810830 ppid: 2 flags:0x00004000
[87452.325520] Workqueue: btrfs-flush_delalloc btrfs_work_helper [btrfs]
[87452.326136] Call Trace:
[87452.326737] __schedule+0x5d1/0xcf0
[87452.327390] schedule+0x45/0xe0
[87452.328174] lock_extent_bits+0x1e6/0x2d0 [btrfs]
[87452.328894] ? finish_wait+0x90/0x90
[87452.329474] btrfs_invalidatepage+0x32c/0x390 [btrfs]
[87452.330133] ? __mod_memcg_state+0x8e/0x160
[87452.330738] __extent_writepage+0x2d4/0x400 [btrfs]
[87452.331405] extent_write_cache_pages+0x2b2/0x500 [btrfs]
[87452.332007] ? lock_release+0x20e/0x4c0
[87452.332557] ? trace_hardirqs_on+0x1b/0xf0
[87452.333127] extent_writepages+0x43/0x90 [btrfs]
[87452.333653] ? lock_acquire+0x1a3/0x490
[87452.334177] do_writepages+0x43/0xe0
[87452.334699] ? __filemap_fdatawrite_range+0xa4/0x100
[87452.335720] __filemap_fdatawrite_range+0xc5/0x100
[87452.336500] btrfs_run_delalloc_work+0x17/0x40 [btrfs]
[87452.337216] btrfs_work_helper+0xf1/0x600 [btrfs]
[87452.337838] process_one_work+0x24e/0x5e0
[87452.338437] worker_thread+0x50/0x3b0
[87452.339137] ? process_one_work+0x5e0/0x5e0
[87452.339884] kthread+0x153/0x170
[87452.340507] ? kthread_mod_delayed_work+0xc0/0xc0
[87452.341153] ret_from_fork+0x22/0x30
[87452.341806] INFO: task kworker/u16:1:2426217 blocked for more than 120 seconds.
[87452.342487] Tainted: G B W 5.10.0-rc4-btrfs-next-73 #1
[87452.343274] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[87452.344049] task:kworker/u16:1 state:D stack: 0 pid:2426217 ppid: 2 flags:0x00004000
[87452.344974] Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs]
[87452.345655] Call Trace:
[87452.346305] __schedule+0x5d1/0xcf0
[87452.346947] ? kvm_clock_read+0x14/0x30
[87452.347676] ? wait_for_completion+0x81/0x110
[87452.348389] schedule+0x45/0xe0
[87452.349077] schedule_timeout+0x30c/0x580
[87452.349718] ? _raw_spin_unlock_irqrestore+0x3c/0x60
[87452.350340] ? lock_acquire+0x1a3/0x490
[87452.351006] ? try_to_wake_up+0x7a/0xa20
[87452.351541] ? lock_release+0x20e/0x4c0
[87452.352040] ? lock_acquired+0x199/0x490
[87452.352517] ? wait_for_completion+0x81/0x110
[87452.353000] wait_for_completion+0xab/0x110
[87452.353490] start_delalloc_inodes+0x2af/0x390 [btrfs]
[87452.353973] btrfs_start_delalloc_roots+0x12d/0x250 [btrfs]
[87452.354455] flush_space+0x24f/0x660 [btrfs]
[87452.355063] btrfs_async_reclaim_metadata_space+0x1bb/0x480 [btrfs]
[87452.355565] process_one_work+0x24e/0x5e0
[87452.356024] worker_thread+0x20f/0x3b0
[87452.356487] ? process_one_work+0x5e0/0x5e0
[87452.356973] kthread+0x153/0x170
[87452.357434] ? kthread_mod_delayed_work+0xc0/0xc0
[87452.357880] ret_from_fork+0x22/0x30
(...)
< stack traces of several tasks waiting for the locks of the inodes of the
clone operation >
(...)
[92867.444138] RSP: 002b:00007ffc3371bbe8 EFLAGS: 00000246 ORIG_RAX: 0000000000000052
[92867.444624] RAX: ffffffffffffffda RBX: 00007ffc3371bea0 RCX: 00007f61efe73f97
[92867.445116] RDX: 0000000000000000 RSI: 0000560fbd5d7a40 RDI: 0000560fbd5d8960
[92867.445595] RBP: 00007ffc3371beb0 R08: 0000000000000001 R09: 0000000000000003
[92867.446070] R10: 00007ffc3371b996 R11: 0000000000000246 R12: 0000000000000000
[92867.446820] R13: 000000000000001f R14: 00007ffc3371bea0 R15: 00007ffc3371beb0
[92867.447361] task:fsstress state:D stack: 0 pid:2508238 ppid:2508153 flags:0x00004000
[92867.447920] Call Trace:
[92867.448435] __schedule+0x5d1/0xcf0
[92867.448934] ? _raw_spin_unlock_irqrestore+0x3c/0x60
[92867.449423] schedule+0x45/0xe0
[92867.449916] __reserve_bytes+0x4a4/0xb10 [btrfs]
[92867.450576] ? finish_wait+0x90/0x90
[92867.451202] btrfs_reserve_metadata_bytes+0x29/0x190 [btrfs]
[92867.451815] btrfs_block_rsv_add+0x1f/0x50 [btrfs]
[92867.452412] start_transaction+0x2d1/0x760 [btrfs]
[92867.453216] clone_copy_inline_extent+0x333/0x490 [btrfs]
[92867.453848] ? lock_release+0x20e/0x4c0
[92867.454539] ? btrfs_search_slot+0x9a7/0xc30 [btrfs]
[92867.455218] btrfs_clone+0x569/0x7e0 [btrfs]
[92867.455952] btrfs_clone_files+0xf6/0x150 [btrfs]
[92867.456588] btrfs_remap_file_range+0x324/0x3d0 [btrfs]
[92867.457213] do_clone_file_range+0xd4/0x1f0
[92867.457828] vfs_clone_file_range+0x4d/0x230
[92867.458355] ? lock_release+0x20e/0x4c0
[92867.458890] ioctl_file_clone+0x8f/0xc0
[92867.459377] do_vfs_ioctl+0x342/0x750
[92867.459913] __x64_sys_ioctl+0x62/0xb0
[92867.460377] do_syscall_64+0x33/0x80
[92867.460842] entry_SYSCALL_64_after_hwframe+0x44/0xa9
(...)
< stack traces of more tasks blocked on metadata reservation like the clone
task above, because the async reclaim task has deadlocked >
(...)
Another thing to notice is that the worker task that is deadlocked when
trying to flush the destination inode of the clone operation is at
btrfs_invalidatepage(). This is simply because the clone operation has a
destination offset greater than the i_size and we only update the i_size
of the destination file after cloning an extent (just like we do in the
buffered write path).
Since the async reclaim path uses btrfs_start_delalloc_roots() to trigger
the flushing of delalloc for all inodes that have delalloc, add a runtime
flag to an inode to signal it should not be flushed, and for inodes with
that flag set, start_delalloc_inodes() will simply skip them. When the
cloning code needs to dirty a page to copy an inline extent, set that flag
on the inode and then clear it when the clone operation finishes.
This could be sporadically triggered with test case generic/269 from
fstests, which exercises many fsstress processes running in parallel with
several dd processes filling up the entire filesystem.
CC: stable@vger.kernel.org # 5.9+
Fixes: 05a5a7621c ("Btrfs: implement full reflink support for inline extents")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Refactor btrfs_lookup_bio_sums() by:
- Remove the @file_offset parameter
There are two factors making the @file_offset parameter useless:
* For csum lookup in csum tree, file offset makes no sense
We only need disk_bytenr, which is unrelated to file_offset
* page_offset (file offset) of each bvec is not contiguous.
Pages can be added to the same bio as long as their on-disk bytenr
is contiguous, meaning we could have pages at different file offsets
in the same bio.
Thus passing file_offset makes no sense any more.
The only user of file_offset is for data reloc inode, we will use
a new function, search_file_offset_in_bio(), to handle it.
- Extract the csum tree lookup into search_csum_tree()
The new function will handle the csum search in csum tree.
The return value is the same as btrfs_find_ordered_sum(), returning
the number of found sectors which have checksum.
- Change how we do the main loop
The only needed info from bio is:
* the on-disk bytenr
* the length
After extracting the above info, we can do the search without bio
at all, which makes the main loop much simpler:
for (cur_disk_bytenr = orig_disk_bytenr;
cur_disk_bytenr < orig_disk_bytenr + orig_len;
cur_disk_bytenr += count * sectorsize) {
/* Lookup csum tree */
count = search_csum_tree(fs_info, path, cur_disk_bytenr,
search_len, csum_dst);
if (!count) {
/* Csum hole handling */
}
}
- Use single variable as the source to calculate all other offsets
Instead of all different type of variables, we use only one main
variable, cur_disk_bytenr, which represents the current disk bytenr.
All involved values can be calculated from that variable, and
all those variable will only be visible in the inner loop.
The above refactoring makes btrfs_lookup_bio_sums() way more robust than
it used to be, especially related to the file offset lookup. Now
file_offset lookup is only related to data reloc inode, otherwise we
don't need to bother file_offset at all.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently btrfs_verify_data_csum() just passes the whole page to
check_data_csum(), which is fine since we only support sectorsize ==
PAGE_SIZE.
To support subpage, we need to properly honor per-sector
checksum verification, just like what we did in dio read path.
This patch will do the csum verification in a for loop, starts with
pg_off == start - page_offset(page), with sectorsize increase for
each loop.
For sectorsize == PAGE_SIZE case, the pg_off will always be 0, and we
will only loop once.
For subpage case, we do the iterate over each sector and if we found any
error, we return error.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Parameter icsum for check_data_csum() is a little hard to understand.
So is the phy_offset for btrfs_verify_data_csum().
Both parameters are calculated values for csum lookup.
Instead of some calculated value, just pass bio_offset and let the
final and only user, check_data_csum(), calculate whatever it needs.
Since we are here, also make the bio_offset parameter and some related
variables to be u32 (unsigned int).
As bio size is limited by its bi_size, which is unsigned int, and has
extra size limit check during various bio operations.
Thus we are ensured that bio_offset won't overflow u32.
Thus for all involved functions, not only rename the parameter from
@phy_offset to @bio_offset, but also reduce its width to u32, so we
won't have suspicious "u32 = u64 >> sector_bits;" lines anymore.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The parameter bio_offset of extent_submit_bio_start_t is very confusing.
If it's really bio_offset (offset to bio), then it should be u32. But
in fact, it's only utilized by dio read, and that member is used as file
offset, which must be u64.
Rename it to dio_file_offset since the only user uses it as file offset,
and add comment for who is using it.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's been deprecated since commit b547a88ea5 ("btrfs: start
deprecation of mount option inode_cache") which enumerates the reasons.
A filesystem that uses the feature (mount -o inode_cache) tracks the
inode numbers in bitmaps, that data stay on the filesystem after this
patch. The size is roughly 5MiB for 1M inodes [1], which is considered
small enough to be left there. Removal of the change can be implemented
in btrfs-progs if needed.
[1] https://lore.kernel.org/linux-btrfs/20201127145836.GZ6430@twin.jikos.cz/
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
The former is going away as part of the inode map removal so switch
callers to btrfs_find_free_objectid. No functional changes since with
INODE_MAP disabled (default) find_free_objectid was called anyway.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since commit 72deb455b5 ("block: remove CONFIG_LBDAF") (5.2) the
sector_t type is u64 on all arches and configs so we don't need to
typecast it. It used to be unsigned long and the result of sector size
shifts were not guaranteed to fit in the type.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Use only a single 'ret' to control whether we should abort the
transaction or not. That's fine, because if we abort a transaction then
btrfs_end_transaction will return the same value as passed to
btrfs_abort_transaction. No semantic changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we are attempting to start writeback for an existing extent in NOCOW
mode, at run_delalloc_nocow(), we must check if the extent is shared, and
if it is, fallback to a COW write. However we do such check while still
holding a read lock on the leaf that contains the file extent item, and
that check, the call to btrfs_cross_ref_exist(), can take some time
because:
1) It needs to do a search on the extent tree, which obviously takes some
time, specially if delayed references are being run at the moment, as
we can block when trying to lock currently write locked btree nodes;
2) It needs to check the delayed references for any existing reference
for our data extent, this requires acquiring the delayed references'
spinlock and maybe block on the mutex of a delayed reference head in the
case where there is a delayed reference for our data extent, in the
worst case it makes us release the path on the extent tree and retry
the whole process again (going back to step 1).
There are other operations we do while holding the leaf locked that can
take some significant time as well (specially all together):
* btrfs_extent_readonly() - to check if the block group containing the
extent is currently in RO mode. This requires taking a spinlock and
searching for the block group in a rbtree that can be big on large
filesystems;
* csum_exist_in_range() - to search if there are any checksums in the
csum tree for the extent. Like before, this can take some time if we are
in a filesystem that has both COW and NOCOW files, in which case the
csum tree is not empty;
* btrfs_inc_nocow_writers() - increment the number of nocow writers in the
block group that contains the data extent. Needs to acquire a spinlock
and search for the block group in a rbtree that can be big on large
filesystems.
So just unlock the leaf (release the path) before doing all those checks,
since we do not need it anymore. In case we can not do a NOCOW write for
the extent, due to any of those checks failing, and the writeback range
goes beyond that extents' length, we will do another btree search for the
next file extent item.
The following script that calls dbench was used to measure the impact of
this change on a VM with 8 CPUs, 16Gb of ram, using a raw NVMe device
directly (no intermediary filesystem on the host) and using a non-debug
kernel (default configuration on Debian):
$ cat test-dbench.sh
#!/bin/bash
DEV=/dev/sdk
MNT=/mnt/sdk
MOUNT_OPTIONS="-o ssd -o nodatacow"
MKFS_OPTIONS="-m single -d single"
mkfs.btrfs -f $MKFS_OPTIONS $DEV
mount $MOUNT_OPTIONS $DEV $MNT
dbench -D $MNT -t 300 64
umount $MNT
Before this change:
Operation Count AvgLat MaxLat
----------------------------------------
NTCreateX 9326331 0.317 399.957
Close 6851198 0.002 6.402
Rename 394894 2.621 402.819
Unlink 1883131 0.931 398.082
Deltree 256 19.160 303.580
Mkdir 128 0.003 0.016
Qpathinfo 8452314 0.068 116.133
Qfileinfo 1481921 0.001 5.081
Qfsinfo 1549963 0.002 4.444
Sfileinfo 759679 0.084 17.079
Find 3268168 0.396 118.196
WriteX 4653310 0.056 110.993
ReadX 14618818 0.005 23.314
LockX 30364 0.003 0.497
UnlockX 30364 0.002 1.720
Flush 653619 16.954 569.299
Throughput 966.651 MB/sec 64 clients 64 procs max_latency=569.377 ms
After this change:
Operation Count AvgLat MaxLat
----------------------------------------
NTCreateX 9710433 0.302 232.449
Close 7132948 0.002 11.496
Rename 411144 2.452 131.805
Unlink 1960961 0.893 230.383
Deltree 256 14.858 198.646
Mkdir 128 0.002 0.005
Qpathinfo 8800890 0.066 111.588
Qfileinfo 1542556 0.001 3.852
Qfsinfo 1613835 0.002 5.483
Sfileinfo 790871 0.081 19.492
Find 3402743 0.386 120.185
WriteX 4842918 0.054 179.312
ReadX 15220407 0.005 32.435
LockX 31612 0.003 1.533
UnlockX 31612 0.002 1.047
Flush 680567 16.320 463.323
Throughput 1016.59 MB/sec 64 clients 64 procs max_latency=463.327 ms
+5.0% throughput, -20.5% max latency
Also, the following test using fio was run:
$ cat test-fio.sh
#!/bin/bash
DEV=/dev/sdk
MNT=/mnt/sdk
MOUNT_OPTIONS="-o ssd -o nodatacow"
MKFS_OPTIONS="-d single -m single"
if [ $# -ne 4 ]; then
echo "Use $0 NUM_JOBS FILE_SIZE FSYNC_FREQ BLOCK_SIZE"
exit 1
fi
NUM_JOBS=$1
FILE_SIZE=$2
FSYNC_FREQ=$3
BLOCK_SIZE=$4
cat <<EOF > /tmp/fio-job.ini
[writers]
rw=randwrite
fsync=$FSYNC_FREQ
fallocate=none
group_reporting=1
direct=0
bs=$BLOCK_SIZE
ioengine=sync
size=$FILE_SIZE
directory=$MNT
numjobs=$NUM_JOBS
EOF
echo
echo "Using fio config:"
echo
cat /tmp/fio-job.ini
echo
echo "mount options: $MOUNT_OPTIONS"
echo
mkfs.btrfs -f $MKFS_OPTIONS $DEV > /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
echo "Creating nodatacow files before fio runs..."
for ((i = 0; i < $NUM_JOBS; i++)); do
xfs_io -f -c "pwrite -b 128M 0 $FILE_SIZE" "$MNT/writers.$i.0"
done
sync
fio /tmp/fio-job.ini
umount $MNT
Before this change:
$ ./test-fio.sh 16 512M 2 4K
(...)
WRITE: bw=28.3MiB/s (29.6MB/s), 28.3MiB/s-28.3MiB/s (29.6MB/s-29.6MB/s), io=8192MiB (8590MB), run=289800-289800msec
After this change:
$ ./test-fio.sh 16 512M 2 4K
(...)
WRITE: bw=31.2MiB/s (32.7MB/s), 31.2MiB/s-31.2MiB/s (32.7MB/s-32.7MB/s), io=8192MiB (8590MB), run=262845-262845msec
+9.7% throughput, -9.8% runtime
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
At inode.c:cow_file_range_inline(), after we insert the inline extent
in the fs/subvolume btree, we call btrfs_drop_extent_cache() to drop
all extent maps in the file range, however that is not necessary because
we have already done it in the call to btrfs_drop_extents(), which calls
btrfs_drop_extent_cache() for us, and since at this point we have the file
range locked in the inode's iotree (we are in the writeback path), we know
no other task can come in and read stale file extent items or find none
and therefore create either stale extent maps or an extent map that
represents a hole.
So just remove that unnecessary call to btrfs_drop_extent_cache(), as it's
doing nothing and only wasting time. This call has been around since 2008,
introduced in commit c8b978188c ("Btrfs: Add zlib compression support"),
but even back then it seems it was not necessary, since we had the range
locked in the inode's iotree and the call to btrfs_drop_extents() already
used to always call btrfs_drop_extent_cache().
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are only 2 direct calls to set_extent_bit outside of extent-io -
in btrfs_find_new_delalloc_bytes and btrfs_truncate_block, the rest are
thin wrappers around __set_extent_bit. This adds unnecessary indirection
and just makes it more annoying when looking at the various extent bit
manipulation functions. This patch renames __set_extent_bit to
set_extent_bit effectively removing a level of indirection. No
functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ reformat and remove __must_check ]
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are several occasions where we do not update the inode's number of
used bytes atomically, resulting in a concurrent stat(2) syscall to report
a value of used blocks that does not correspond to a valid value, that is,
a value that does not match neither what we had before the operation nor
what we get after the operation completes.
In extreme cases it can result in stat(2) reporting zero used blocks, which
can cause problems for some userspace tools where they can consider a file
with a non-zero size and zero used blocks as completely sparse and skip
reading data, as reported/discussed a long time ago in some threads like
the following:
https://lists.gnu.org/archive/html/bug-tar/2016-07/msg00001.html
The cases where this can happen are the following:
-> Case 1
If we do a write (buffered or direct IO) against a file region for which
there is already an allocated extent (or multiple extents), then we have a
short time window where we can report a number of used blocks to stat(2)
that does not take into account the file region being overwritten. This
short time window happens when completing the ordered extent(s).
This happens because when we drop the extents in the write range we
decrement the inode's number of bytes and later on when we insert the new
extent(s) we increment the number of bytes in the inode, resulting in a
short time window where a stat(2) syscall can get an incorrect number of
used blocks.
If we do writes that overwrite an entire file, then we have a short time
window where we report 0 used blocks to stat(2).
Example reproducer:
$ cat reproducer-1.sh
#!/bin/bash
MNT=/mnt/sdi
DEV=/dev/sdi
stat_loop()
{
trap "wait; exit" SIGTERM
local filepath=$1
local expected=$2
local got
while :; do
got=$(stat -c %b $filepath)
if [ $got -ne $expected ]; then
echo -n "ERROR: unexpected used blocks"
echo " (got: $got expected: $expected)"
fi
done
}
mkfs.btrfs -f $DEV > /dev/null
# mkfs.xfs -f $DEV > /dev/null
# mkfs.ext4 -F $DEV > /dev/null
# mkfs.f2fs -f $DEV > /dev/null
# mkfs.reiserfs -f $DEV > /dev/null
mount $DEV $MNT
xfs_io -f -s -c "pwrite -b 64K 0 64K" $MNT/foobar >/dev/null
expected=$(stat -c %b $MNT/foobar)
# Create a process to keep calling stat(2) on the file and see if the
# reported number of blocks used (disk space used) changes, it should
# not because we are not increasing the file size nor punching holes.
stat_loop $MNT/foobar $expected &
loop_pid=$!
for ((i = 0; i < 50000; i++)); do
xfs_io -s -c "pwrite -b 64K 0 64K" $MNT/foobar >/dev/null
done
kill $loop_pid &> /dev/null
wait
umount $DEV
$ ./reproducer-1.sh
ERROR: unexpected used blocks (got: 0 expected: 128)
ERROR: unexpected used blocks (got: 0 expected: 128)
(...)
Note that since this is a short time window where the race can happen, the
reproducer may not be able to always trigger the bug in one run, or it may
trigger it multiple times.
-> Case 2
If we do a buffered write against a file region that does not have any
allocated extents, like a hole or beyond EOF, then during ordered extent
completion we have a short time window where a concurrent stat(2) syscall
can report a number of used blocks that does not correspond to the value
before or after the write operation, a value that is actually larger than
the value after the write completes.
This happens because once we start a buffered write into an unallocated
file range we increment the inode's 'new_delalloc_bytes', to make sure
any stat(2) call gets a correct used blocks value before delalloc is
flushed and completes. However at ordered extent completion, after we
inserted the new extent, we increment the inode's number of bytes used
with the size of the new extent, and only later, when clearing the range
in the inode's iotree, we decrement the inode's 'new_delalloc_bytes'
counter with the size of the extent. So this results in a short time
window where a concurrent stat(2) syscall can report a number of used
blocks that accounts for the new extent twice.
Example reproducer:
$ cat reproducer-2.sh
#!/bin/bash
MNT=/mnt/sdi
DEV=/dev/sdi
stat_loop()
{
trap "wait; exit" SIGTERM
local filepath=$1
local expected=$2
local got
while :; do
got=$(stat -c %b $filepath)
if [ $got -ne $expected ]; then
echo -n "ERROR: unexpected used blocks"
echo " (got: $got expected: $expected)"
fi
done
}
mkfs.btrfs -f $DEV > /dev/null
# mkfs.xfs -f $DEV > /dev/null
# mkfs.ext4 -F $DEV > /dev/null
# mkfs.f2fs -f $DEV > /dev/null
# mkfs.reiserfs -f $DEV > /dev/null
mount $DEV $MNT
touch $MNT/foobar
write_size=$((64 * 1024))
for ((i = 0; i < 16384; i++)); do
offset=$(($i * $write_size))
xfs_io -c "pwrite -S 0xab $offset $write_size" $MNT/foobar >/dev/null
blocks_used=$(stat -c %b $MNT/foobar)
# Fsync the file to trigger writeback and keep calling stat(2) on it
# to see if the number of blocks used changes.
stat_loop $MNT/foobar $blocks_used &
loop_pid=$!
xfs_io -c "fsync" $MNT/foobar
kill $loop_pid &> /dev/null
wait $loop_pid
done
umount $DEV
$ ./reproducer-2.sh
ERROR: unexpected used blocks (got: 265472 expected: 265344)
ERROR: unexpected used blocks (got: 284032 expected: 283904)
(...)
Note that since this is a short time window where the race can happen, the
reproducer may not be able to always trigger the bug in one run, or it may
trigger it multiple times.
-> Case 3
Another case where such problems happen is during other operations that
replace extents in a file range with other extents. Those operations are
extent cloning, deduplication and fallocate's zero range operation.
The cause of the problem is similar to the first case. When we drop the
extents from a range, we decrement the inode's number of bytes, and later
on, after inserting the new extents we increment it. Since this is not
done atomically, a concurrent stat(2) call can see and return a number of
used blocks that is smaller than it should be, does not match the number
of used blocks before or after the clone/deduplication/zero operation.
Like for the first case, when doing a clone, deduplication or zero range
operation against an entire file, we end up having a time window where we
can report 0 used blocks to a stat(2) call.
Example reproducer:
$ cat reproducer-3.sh
#!/bin/bash
MNT=/mnt/sdi
DEV=/dev/sdi
mkfs.btrfs -f $DEV > /dev/null
# mkfs.xfs -f -m reflink=1 $DEV > /dev/null
mount $DEV $MNT
extent_size=$((64 * 1024))
num_extents=16384
file_size=$(($extent_size * $num_extents))
# File foo has many small extents.
xfs_io -f -s -c "pwrite -S 0xab -b $extent_size 0 $file_size" $MNT/foo \
> /dev/null
# File bar has much less extents and has exactly the same data as foo.
xfs_io -f -c "pwrite -S 0xab 0 $file_size" $MNT/bar > /dev/null
expected=$(stat -c %b $MNT/foo)
# Now deduplicate bar into foo. While the deduplication is in progres,
# the number of used blocks/file size reported by stat should not change
xfs_io -c "dedupe $MNT/bar 0 0 $file_size" $MNT/foo > /dev/null &
dedupe_pid=$!
while [ -n "$(ps -p $dedupe_pid -o pid=)" ]; do
used=$(stat -c %b $MNT/foo)
if [ $used -ne $expected ]; then
echo "Unexpected blocks used: $used (expected: $expected)"
fi
done
umount $DEV
$ ./reproducer-3.sh
Unexpected blocks used: 2076800 (expected: 2097152)
Unexpected blocks used: 2097024 (expected: 2097152)
Unexpected blocks used: 2079872 (expected: 2097152)
(...)
Note that since this is a short time window where the race can happen, the
reproducer may not be able to always trigger the bug in one run, or it may
trigger it multiple times.
So fix this by:
1) Making btrfs_drop_extents() not decrement the VFS inode's number of
bytes, and instead return the number of bytes;
2) Making any code that drops extents and adds new extents update the
inode's number of bytes atomically, while holding the btrfs inode's
spinlock, which is also used by the stat(2) callback to get the inode's
number of bytes;
3) For ranges in the inode's iotree that are marked as 'delalloc new',
corresponding to previously unallocated ranges, increment the inode's
number of bytes when clearing the 'delalloc new' bit from the range,
in the same critical section that decrements the inode's
'new_delalloc_bytes' counter, delimited by the btrfs inode's spinlock.
An alternative would be to have btrfs_getattr() wait for any IO (ordered
extents in progress) and locking the whole range (0 to (u64)-1) while it
it computes the number of blocks used. But that would mean blocking
stat(2), which is a very used syscall and expected to be fast, waiting
for writes, clone/dedupe, fallocate, page reads, fiemap, etc.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are many arguments for __btrfs_drop_extents() and its wrapper
btrfs_drop_extents(), which makes it hard to add more arguments to it and
requires changing every caller. I have added a couple myself back in 2014
commit 1acae57b16 ("Btrfs: faster file extent item replace operations")
and therefore know firsthand that it is a bit cumbersome to add additional
arguments to these functions.
Since I will need to add more arguments in a subsequent bug fix, this
change is preparatory work and adds a data structure that holds all the
arguments, for both input and output, that are passed to this function,
with some comments in the structure's definition mentioning what each
field is and how it relates to other fields.
Callers of this function need only to zero out the content of the
structure and setup only the fields they need. This also removes the
need to have both __btrfs_drop_extents() and btrfs_drop_extents(), so
now we have a single function named btrfs_drop_extents() that takes a
pointer to this new data structure (struct btrfs_drop_extents_args).
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Historically we've allowed recursive locking specifically for the free
space inode. This is because we are only doing reads and know that it's
safe. However we don't actually need this feature, we can get away with
reading the commit root for the extents. In fact if we want to allow
asynchronous loading of the free space cache we have to use the commit
root, otherwise we will deadlock.
Switch to using the commit root for the file extents. These are only
read at load time, and are replaced as soon as we start writing the
cache out to disk. The cache is never read again, so this is
legitimate. This matches what we do for the inode itself, as we read
that from the commit root as well.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We no longer distinguish between blocking and spinning, so rip out all
this code.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that we're using a rw_semaphore we no longer need to indicate if a
lock is blocking or not, nor do we need to flip the entire path from
blocking to spinning. Remove these helpers and all the places they are
called.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The fs_info value is 32bit, switch also the local u16 variables. This
leads to a better assembly code generated due to movzwl.
This simple change will shave some bytes on x86_64 and release config:
text data bss dec hex filename
1090000 17980 14912 1122892 11224c pre/btrfs.ko
1089794 17980 14912 1122686 11217e post/btrfs.ko
DELTA: -206
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_get_16 shows up in the system performance profiles (helper to read
16bit values from on-disk structures). This is partially because of the
checksum size that's frequently read along with data reads/writes, other
u16 uses are from item size or directory entries.
Replace all calls to btrfs_super_csum_size by the cached value from
fs_info.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The value of super_block::s_blocksize_bits is the same as
fs_info::sectorsize_bits, but we don't need to do the extra dereferences
in many functions and storing the bits as u32 (in fs_info) generates
shorter assembly.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
For check_data_csum(), the page we're using is directly from the inode
mapping, thus it has valid page_offset().
We can use (page_offset() + pg_off) to replace @start parameter
completely, while the @len should always be sectorsize.
Since we're here, also add some comment, as there are quite some
confusion in words like start/offset, without explaining whether it's
file_offset or logical bytenr.
This should not affect the existing behavior, as for current sectorsize
== PAGE_SIZE case, @pgoff should always be 0, and len is always
PAGE_SIZE (or sectorsize from the dio read path).
Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All callers of btrfs_wq_submit_bio() pass struct inode as @private_data,
so there is no need for it to be (void *), replace it with "struct inode
*inode".
While we can extract fs_info from struct inode, also remove the @fs_info
parameter.
Since we're here, also replace all the (void *private_data) into (struct
inode *inode).
Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The @failed_start parameter is only paired with @exclusive_bits, and
those parameters are only used for EXTENT_LOCKED bit, which have their
own wrappers lock_extent_bits().
Thus for regular set_extent_bit() calls, the failed_start makes no
sense, just sink the parameter.
Also, since @failed_start and @exclusive_bits are used in pairs, add
an assert to make it obvious.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The drop_level member is used directly unlike all the other int types in
root_item. Add the definition and use it everywhere. The type is u8 so
there's no conversion necessary and the helpers are properly inlined,
this is for consistency.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This effectively reverts 09745ff88d93 ("btrfs: dio iomap DSYNC
workaround") now that the iomap API has been updated to allow
iomap_dio_complete() not to be called under i_rwsem anymore.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The inode dio_sem can be eliminated because all DIO synchronization is
now performed through inode->i_rwsem that provides the same guarantees.
This reduces btrfs_inode size by 40 bytes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_inode_lock/unlock() are wrappers around inode locks, separating
the type of lock and actual locking.
- 0 - default, exclusive lock
- BTRFS_ILOCK_SHARED - for shared locks, for possible parallel DIO
- BTRFS_ILOCK_TRY - for the RWF_NOWAIT sequence
The bits SHARED and TRY can be combined together.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The read and write DIO don't have anything in common except for the
call to iomap_dio_rw. Extract the write call into a new function to get
rid of conditional statements for direct write.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Sterba <dsterba@suse.com>
In the face of extent root corruption, or any other core fs wide root
corruption we will fail to mount the file system. This makes recovery
kind of a pain, because you need to fall back to userspace tools to
scrape off data. Instead provide a mechanism to gracefully handle bad
roots, so we can at least mount read-only and possibly recover data from
the file system.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we move to being able to handle NULL csum_roots it'll be cleaner to
just check in btrfs_lookup_bio_sums instead of at all of the caller
locations, so push the NODATASUM check into it as well so it's unified.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing a buffered write, through one of the write family syscalls, we
look for ranges which currently don't have allocated extents and set the
'delalloc new' bit on them, so that we can report a correct number of used
blocks to the stat(2) syscall until delalloc is flushed and ordered extents
complete.
However there are a few other places where we can do a buffered write
against a range that is mapped to a hole (no extent allocated) and where
we do not set the 'new delalloc' bit. Those places are:
- Doing a memory mapped write against a hole;
- Cloning an inline extent into a hole starting at file offset 0;
- Calling btrfs_cont_expand() when the i_size of the file is not aligned
to the sector size and is located in a hole. For example when cloning
to a destination offset beyond EOF.
So after such cases, until the corresponding delalloc range is flushed and
the respective ordered extents complete, we can report an incorrect number
of blocks used through the stat(2) syscall.
In some cases we can end up reporting 0 used blocks to stat(2), which is a
particular bad value to report as it may mislead tools to think a file is
completely sparse when its i_size is not zero, making them skip reading
any data, an undesired consequence for tools such as archivers and other
backup tools, as reported a long time ago in the following thread (and
other past threads):
https://lists.gnu.org/archive/html/bug-tar/2016-07/msg00001.html
Example reproducer:
$ cat reproducer.sh
#!/bin/bash
MNT=/mnt/sdi
DEV=/dev/sdi
mkfs.btrfs -f $DEV > /dev/null
# mkfs.xfs -f $DEV > /dev/null
# mkfs.ext4 -F $DEV > /dev/null
# mkfs.f2fs -f $DEV > /dev/null
mount $DEV $MNT
xfs_io -f -c "truncate 64K" \
-c "mmap -w 0 64K" \
-c "mwrite -S 0xab 0 64K" \
-c "munmap" \
$MNT/foo
blocks_used=$(stat -c %b $MNT/foo)
echo "blocks used: $blocks_used"
if [ $blocks_used -eq 0 ]; then
echo "ERROR: blocks used is 0"
fi
umount $DEV
$ ./reproducer.sh
blocks used: 0
ERROR: blocks used is 0
So move the logic that decides to set the 'delalloc bit' bit into the
function btrfs_set_extent_delalloc(), since that is what we use for all
those missing cases as well as for the cases that currently work well.
This change is also preparatory work for an upcoming patch that fixes
other problems related to tracking and reporting the number of bytes used
by an inode.
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing a fallocate() we have a short time window, after reserving an
extent and before starting a transaction, where if relocation for the block
group containing the reserved extent happens, we can end up missing the
extent in the data relocation inode causing relocation to fail later.
This only happens when we don't pass a transaction to the internal
fallocate function __btrfs_prealloc_file_range(), which is for all the
cases where fallocate() is called from user space (the internal use cases
include space cache extent allocation and relocation).
When the race triggers the relocation failure, it produces a trace like
the following:
[200611.995995] ------------[ cut here ]------------
[200611.997084] BTRFS: Transaction aborted (error -2)
[200611.998208] WARNING: CPU: 3 PID: 235845 at fs/btrfs/ctree.c:1074 __btrfs_cow_block+0x3a0/0x5b0 [btrfs]
[200611.999042] Modules linked in: dm_thin_pool dm_persistent_data (...)
[200612.003287] CPU: 3 PID: 235845 Comm: btrfs Not tainted 5.9.0-rc6-btrfs-next-69 #1
[200612.004442] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[200612.006186] RIP: 0010:__btrfs_cow_block+0x3a0/0x5b0 [btrfs]
[200612.007110] Code: 1b 00 00 02 72 2a 83 f8 fb 0f 84 b8 01 (...)
[200612.007341] BTRFS warning (device sdb): Skipping commit of aborted transaction.
[200612.008959] RSP: 0018:ffffaee38550f918 EFLAGS: 00010286
[200612.009672] BTRFS: error (device sdb) in cleanup_transaction:1901: errno=-30 Readonly filesystem
[200612.010428] RAX: 0000000000000000 RBX: ffff9174d96f4000 RCX: 0000000000000000
[200612.011078] BTRFS info (device sdb): forced readonly
[200612.011862] RDX: 0000000000000001 RSI: ffffffffa8161978 RDI: 00000000ffffffff
[200612.013215] RBP: ffff9172569a0f80 R08: 0000000000000000 R09: 0000000000000000
[200612.014263] R10: 0000000000000000 R11: 0000000000000000 R12: ffff9174b8403b88
[200612.015203] R13: ffff9174b8400a88 R14: ffff9174c90f1000 R15: ffff9174a5a60e08
[200612.016182] FS: 00007fa55cf878c0(0000) GS:ffff9174ece00000(0000) knlGS:0000000000000000
[200612.017174] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[200612.018418] CR2: 00007f8fb8048148 CR3: 0000000428a46003 CR4: 00000000003706e0
[200612.019510] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[200612.020648] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[200612.021520] Call Trace:
[200612.022434] btrfs_cow_block+0x10b/0x250 [btrfs]
[200612.023407] do_relocation+0x54e/0x7b0 [btrfs]
[200612.024343] ? do_raw_spin_unlock+0x4b/0xc0
[200612.025280] ? _raw_spin_unlock+0x29/0x40
[200612.026200] relocate_tree_blocks+0x3bc/0x6d0 [btrfs]
[200612.027088] relocate_block_group+0x2f3/0x600 [btrfs]
[200612.027961] btrfs_relocate_block_group+0x15e/0x340 [btrfs]
[200612.028896] btrfs_relocate_chunk+0x38/0x110 [btrfs]
[200612.029772] btrfs_balance+0xb22/0x1790 [btrfs]
[200612.030601] ? btrfs_ioctl_balance+0x253/0x380 [btrfs]
[200612.031414] btrfs_ioctl_balance+0x2cf/0x380 [btrfs]
[200612.032279] btrfs_ioctl+0x620/0x36f0 [btrfs]
[200612.033077] ? _raw_spin_unlock+0x29/0x40
[200612.033948] ? handle_mm_fault+0x116d/0x1ca0
[200612.034749] ? up_read+0x18/0x240
[200612.035542] ? __x64_sys_ioctl+0x83/0xb0
[200612.036244] __x64_sys_ioctl+0x83/0xb0
[200612.037269] do_syscall_64+0x33/0x80
[200612.038190] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[200612.038976] RIP: 0033:0x7fa55d07ed87
[200612.040127] Code: 00 00 00 48 8b 05 09 91 0c 00 64 c7 00 26 (...)
[200612.041669] RSP: 002b:00007ffd5ebf03e8 EFLAGS: 00000206 ORIG_RAX: 0000000000000010
[200612.042437] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007fa55d07ed87
[200612.043511] RDX: 00007ffd5ebf0470 RSI: 00000000c4009420 RDI: 0000000000000003
[200612.044250] RBP: 0000000000000003 R08: 000055d8362642a0 R09: 00007fa55d148be0
[200612.044963] R10: fffffffffffff52e R11: 0000000000000206 R12: 00007ffd5ebf1614
[200612.045683] R13: 00007ffd5ebf0470 R14: 0000000000000002 R15: 00007ffd5ebf0470
[200612.046361] irq event stamp: 0
[200612.047040] hardirqs last enabled at (0): [<0000000000000000>] 0x0
[200612.047725] hardirqs last disabled at (0): [<ffffffffa6eb5ab3>] copy_process+0x823/0x1bc0
[200612.048387] softirqs last enabled at (0): [<ffffffffa6eb5ab3>] copy_process+0x823/0x1bc0
[200612.049024] softirqs last disabled at (0): [<0000000000000000>] 0x0
[200612.049722] ---[ end trace 49006c6876e65227 ]---
The race happens like this:
1) Task A starts an fallocate() (plain or zero range) and it calls
__btrfs_prealloc_file_range() with the 'trans' parameter set to NULL;
2) Task A calls btrfs_reserve_extent() and gets an extent that belongs to
block group X;
3) Before task A gets into btrfs_replace_file_extents(), through the call
to insert_prealloc_file_extent(), task B starts relocation of block
group X;
4) Task B enters btrfs_relocate_block_group() and it sets block group X to
RO mode;
5) Task B enters relocate_block_group(), it calls prepare_to_relocate()
whichs joins/starts a transaction and then commits the transaction;
6) Task B then starts scanning the extent tree looking for extents that
belong to block group X - it does not find yet the extent reserved by
task A, since that extent was not yet added to the extent tree, as its
delayed reference was not even yet created at this point;
7) The data relocation inode ends up not having the extent reserved by
task A associated to it;
8) Task A then starts a transaction through btrfs_replace_file_extents(),
inserts a file extent item in the subvolume tree pointing to the
reserved extent and creates a delayed reference for it;
9) Task A finishes and returns success to user space;
10) Later on, while relocation is still in progress, the leaf where task A
inserted the new file extent item is COWed, so we end up at
__btrfs_cow_block(), which calls btrfs_reloc_cow_block(), and that in
turn calls relocation.c:replace_file_extents();
11) At relocation.c:replace_file_extents() we iterate over all the items in
the leaf and find the file extent item pointing to the extent that was
allocated by task A, and then call relocation.c:get_new_location(), to
find the new location for the extent;
12) However relocation.c:get_new_location() fails, returning -ENOENT,
because it couldn't find a corresponding file extent item associated
with the data relocation inode. This is because the extent was not seen
in the extent tree at step 6). The -ENOENT error is propagated to
__btrfs_cow_block(), which aborts the transaction.
So fix this simply by decrementing the block group's number of reservations
after calling insert_prealloc_file_extent(), as relocation waits for that
counter to go down to zero before calling prepare_to_relocate() and start
looking for extents in the extent tree.
This issue only started to happen recently as of commit 8fccebfa53
("btrfs: fix metadata reservation for fallocate that leads to transaction
aborts"), because now we can reserve an extent before starting/joining a
transaction, and previously we always did it after that, so relocation
ended up waiting for a concurrent fallocate() to finish because before
searching for the extents of the block group, it starts/joins a transaction
and then commits it (at prepare_to_relocate()), which made it wait for the
fallocate task to complete first.
Fixes: 8fccebfa53 ("btrfs: fix metadata reservation for fallocate that leads to transaction aborts")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit 8d875f95da ("btrfs: disable strict file flushes for
renames and truncates") eliminated the notion of ordered operations and
instead BTRFS_INODE_ORDERED_DATA_CLOSE only remained as a flag
indicating that a file's content should be synced to disk in case a
file is truncated and any writes happen to it concurrently. In fact
this intendend behavior was broken until it was fixed in
f6dc45c7a9 ("Btrfs: fix filemap_flush call in btrfs_file_release").
All things considered let's give the flag a more descriptive name. Also
slightly reword comments.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since we now perform direct reads using i_rwsem, we can remove this
inode flag used to co-ordinate unlocked reads.
The truncate call takes i_rwsem. This means it is correctly synchronized
with concurrent direct reads.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's no longer used just remove the function and any related code which
was initialising it for inodes. No functional changes.
Removing 8 bytes from extent_io_tree in turn reduces size of other
structures where it is embedded, notably btrfs_inode where it reduces
size by 24 bytes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead export and rename the function to btrfs_submit_data_bio and
call it directly in submit_one_bio. This avoids paying the cost for
speculative attacks mitigations and improves code readability.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's no longer used so let's remove it.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Don't call readpage_end_io_hook for the btree inode. Instead of relying
on indirect calls to implement metadata buffer validation simply check
if the inode whose page we are processing equals the btree inode. If it
does call the necessary function.
This is an improvement in 2 directions:
1. We aren't paying the penalty of indirect calls in a post-speculation
attacks world.
2. The function is now named more explicitly so it's obvious what's
going on
This is in preparation to removing struct extent_io_ops altogether.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The passed in ordered_extent struct is always well-formed and contains
the inode making the explicit argument redundant.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's used to reference the csum root which can be done from the trans
handle as well. Simplify the signature and while at it also remove the
noinline attribute as the function uses only at most 16 bytes of stack
space.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This makes reading the code a tad easier by decreasing the level of
indirection by one.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's always set to 0 by its sole caller - btrfs_readpage. Simply remove
it.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's always set to 0 from the sole caller - btrfs_readpage.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that btrfs_readpage is the only caller of extent_read_full_page the
latter can be open coded in the former. Use the occassion to rename
__extent_read_full_page to extent_read_full_page. To facillitate this
change submit_one_bio has to be exported as well.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's called only from btrfs_readpage which always passes 0 so just sink
the argument into extent_read_full_page.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that this function is only responsible for reading data pages it's
no longer necessary to pass get_extent_t parameter across several
layers of functions. This patch removes this parameter from multiple
functions: __get_extent_map/__do_readpage/__extent_read_full_page/
extent_read_full_page and simply calls btrfs_get_extent directly in
__get_extent_map.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The function btrfs_punch_hole_range() is now used to replace all the file
extents in a given file range with an extent described in the given struct
btrfs_replace_extent_info argument. This extent can either be an existing
extent that is being cloned or it can be a new extent (namely a prealloc
extent). When that argument is NULL it only punches a hole (drops all the
existing extents) in the file range.
So rename the function to btrfs_replace_file_extents().
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that we can use btrfs_clone_extent_info to convey information for a
new prealloc extent as well, and not just for existing extents that are
being cloned, rename it to btrfs_replace_extent_info, which reflects the
fact that this is now more generic and it is used to replace all existing
extents in a file range with the extent described by the structure.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The value of item_size of struct btrfs_clone_extent_info is always set to
the size of a non-inline file extent item, and in fact the infrastructure
that uses this structure (btrfs_punch_hole_range()) does not work with
inline file extents at all (and it is not supposed to).
So just remove that field from the structure and use directly
sizeof(struct btrfs_file_extent_item) instead. Also assert that the
file extent type is not inline at btrfs_insert_clone_extent().
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing an fallocate(), specially a zero range operation, we assume
that reserving 3 units of metadata space is enough, that at most we touch
one leaf in subvolume/fs tree for removing existing file extent items and
inserting a new file extent item. This assumption is generally true for
most common use cases. However when we end up needing to remove file extent
items from multiple leaves, we can end up failing with -ENOSPC and abort
the current transaction, turning the filesystem to RO mode. When this
happens a stack trace like the following is dumped in dmesg/syslog:
[ 1500.620934] ------------[ cut here ]------------
[ 1500.620938] BTRFS: Transaction aborted (error -28)
[ 1500.620973] WARNING: CPU: 2 PID: 30807 at fs/btrfs/inode.c:9724 __btrfs_prealloc_file_range+0x512/0x570 [btrfs]
[ 1500.620974] Modules linked in: btrfs intel_rapl_msr intel_rapl_common kvm_intel (...)
[ 1500.621010] CPU: 2 PID: 30807 Comm: xfs_io Tainted: G W 5.9.0-rc3-btrfs-next-67 #1
[ 1500.621012] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 1500.621023] RIP: 0010:__btrfs_prealloc_file_range+0x512/0x570 [btrfs]
[ 1500.621026] Code: 8b 40 50 f0 48 (...)
[ 1500.621028] RSP: 0018:ffffb05fc8803ca0 EFLAGS: 00010286
[ 1500.621030] RAX: 0000000000000000 RBX: ffff9608af276488 RCX: 0000000000000000
[ 1500.621032] RDX: 0000000000000001 RSI: 0000000000000027 RDI: 00000000ffffffff
[ 1500.621033] RBP: ffffb05fc8803d90 R08: 0000000000000001 R09: 0000000000000001
[ 1500.621035] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000003200000
[ 1500.621037] R13: 00000000ffffffe4 R14: ffff9608af275fe8 R15: ffff9608af275f60
[ 1500.621039] FS: 00007fb5b2368ec0(0000) GS:ffff9608b6600000(0000) knlGS:0000000000000000
[ 1500.621041] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1500.621043] CR2: 00007fb5b2366fb8 CR3: 0000000202d38005 CR4: 00000000003706e0
[ 1500.621046] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1500.621047] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1500.621049] Call Trace:
[ 1500.621076] btrfs_prealloc_file_range+0x10/0x20 [btrfs]
[ 1500.621087] btrfs_fallocate+0xccd/0x1280 [btrfs]
[ 1500.621108] vfs_fallocate+0x14d/0x290
[ 1500.621112] ksys_fallocate+0x3a/0x70
[ 1500.621117] __x64_sys_fallocate+0x1a/0x20
[ 1500.621120] do_syscall_64+0x33/0x80
[ 1500.621123] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1500.621126] RIP: 0033:0x7fb5b248c477
[ 1500.621128] Code: 89 7c 24 08 (...)
[ 1500.621130] RSP: 002b:00007ffc7bee9060 EFLAGS: 00000293 ORIG_RAX: 000000000000011d
[ 1500.621132] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fb5b248c477
[ 1500.621134] RDX: 0000000000000000 RSI: 0000000000000010 RDI: 0000000000000003
[ 1500.621136] RBP: 0000557718faafd0 R08: 0000000000000000 R09: 0000000000000000
[ 1500.621137] R10: 0000000003200000 R11: 0000000000000293 R12: 0000000000000010
[ 1500.621139] R13: 0000557718faafb0 R14: 0000557718faa480 R15: 0000000000000003
[ 1500.621151] irq event stamp: 1026217
[ 1500.621154] hardirqs last enabled at (1026223): [<ffffffffba965570>] console_unlock+0x500/0x5c0
[ 1500.621156] hardirqs last disabled at (1026228): [<ffffffffba9654c7>] console_unlock+0x457/0x5c0
[ 1500.621159] softirqs last enabled at (1022486): [<ffffffffbb6003dc>] __do_softirq+0x3dc/0x606
[ 1500.621161] softirqs last disabled at (1022477): [<ffffffffbb4010b2>] asm_call_on_stack+0x12/0x20
[ 1500.621162] ---[ end trace 2955b08408d8b9d4 ]---
[ 1500.621167] BTRFS: error (device sdj) in __btrfs_prealloc_file_range:9724: errno=-28 No space left
When we use fallocate() internally, for reserving an extent for a space
cache, inode cache or relocation, we can't hit this problem since either
there aren't any file extent items to remove from the subvolume tree or
there is at most one.
When using plain fallocate() it's very unlikely, since that would require
having many file extent items representing holes for the target range and
crossing multiple leafs - we attempt to increase the range (merge) of such
file extent items when punching holes, so at most we end up with 2 file
extent items for holes at leaf boundaries.
However when using the zero range operation of fallocate() for a large
range (100+ MiB for example) that's fairly easy to trigger. The following
example reproducer triggers the issue:
$ cat reproducer.sh
#!/bin/bash
umount /dev/sdj &> /dev/null
mkfs.btrfs -f -n 16384 -O ^no-holes /dev/sdj > /dev/null
mount /dev/sdj /mnt/sdj
# Create a 100M file with many file extent items. Punch a hole every 8K
# just to speedup the file creation - we could do 4K sequential writes
# followed by fsync (or O_SYNC) as well, but that takes a lot of time.
file_size=$((100 * 1024 * 1024))
xfs_io -f -c "pwrite -S 0xab -b 10M 0 $file_size" /mnt/sdj/foobar
for ((i = 0; i < $file_size; i += 8192)); do
xfs_io -c "fpunch $i 4096" /mnt/sdj/foobar
done
# Force a transaction commit, so the zero range operation will be forced
# to COW all metadata extents it need to touch.
sync
xfs_io -c "fzero 0 $file_size" /mnt/sdj/foobar
umount /mnt/sdj
$ ./reproducer.sh
wrote 104857600/104857600 bytes at offset 0
100 MiB, 10 ops; 0.0669 sec (1.458 GiB/sec and 149.3117 ops/sec)
fallocate: No space left on device
$ dmesg
<shows the same stack trace pasted before>
To fix this use the existing infrastructure that hole punching and
extent cloning use for replacing a file range with another extent. This
deals with doing the removal of file extent items and inserting the new
one using an incremental approach, reserving more space when needed and
always ensuring we don't leave an implicit hole in the range in case
we need to do multiple iterations and a crash happens between iterations.
A test case for fstests will follow up soon.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead of using a flag bit for exclusive operation, use a variable to
store which exclusive operation is being performed. Introduce an API
to start and finish an exclusive operation.
This would enable another way for tools to check which operation is
running on why starting an exclusive operation failed. The followup
patch adds a sysfs_notify() to alert userspace when the state changes, so
userspace can perform select() on it to get notified of the change.
This would enable us to enqueue a command which will wait for current
exclusive operation to complete before issuing the next exclusive
operation. This has been done synchronously as opposed to a background
process, or else error collection (if any) will become difficult.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Our current tree locking stuff allows us to recurse with read locks if
we're already holding the write lock. This is necessary for the space
cache inode, as we could be holding a lock on the root_tree root when we
need to cache a block group, and thus need to be able to read down the
root_tree to read in the inode cache.
We can get away with this in our current locking, but we won't be able
to with a rwsem. Handle this by purposefully annotating the places
where we require recursion, so that in the future we can maybe come up
with a way to avoid the recursion. In the case of the free space inode,
this will be superseded by the free space tree.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
When quota is enabled for TEST_DEV, generic/013 sometimes fails like this:
generic/013 14s ... _check_dmesg: something found in dmesg (see xfstests-dev/results//generic/013.dmesg)
And with the following metadata leak:
BTRFS warning (device dm-3): qgroup 0/1370 has unreleased space, type 2 rsv 49152
------------[ cut here ]------------
WARNING: CPU: 2 PID: 47912 at fs/btrfs/disk-io.c:4078 close_ctree+0x1dc/0x323 [btrfs]
Call Trace:
btrfs_put_super+0x15/0x17 [btrfs]
generic_shutdown_super+0x72/0x110
kill_anon_super+0x18/0x30
btrfs_kill_super+0x17/0x30 [btrfs]
deactivate_locked_super+0x3b/0xa0
deactivate_super+0x40/0x50
cleanup_mnt+0x135/0x190
__cleanup_mnt+0x12/0x20
task_work_run+0x64/0xb0
__prepare_exit_to_usermode+0x1bc/0x1c0
__syscall_return_slowpath+0x47/0x230
do_syscall_64+0x64/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace a6cfd45ba80e4e06 ]---
BTRFS error (device dm-3): qgroup reserved space leaked
BTRFS info (device dm-3): disk space caching is enabled
BTRFS info (device dm-3): has skinny extents
[CAUSE]
The qgroup preallocated meta rsv operations of that offending root are:
btrfs_delayed_inode_reserve_metadata: rsv_meta_prealloc root=1370 num_bytes=131072
btrfs_delayed_inode_reserve_metadata: rsv_meta_prealloc root=1370 num_bytes=131072
btrfs_subvolume_reserve_metadata: rsv_meta_prealloc root=1370 num_bytes=49152
btrfs_delayed_inode_release_metadata: convert_meta_prealloc root=1370 num_bytes=-131072
btrfs_delayed_inode_release_metadata: convert_meta_prealloc root=1370 num_bytes=-131072
It's pretty obvious that, we reserve qgroup meta rsv in
btrfs_subvolume_reserve_metadata(), but doesn't have corresponding
release/convert calls in btrfs_subvolume_release_metadata().
This leads to the leakage.
[FIX]
To fix this bug, we should follow what we're doing in
btrfs_delalloc_reserve_metadata(), where we reserve qgroup space, and
add it to block_rsv->qgroup_rsv_reserved.
And free the qgroup reserved metadata space when releasing the
block_rsv.
To do this, we need to change the btrfs_subvolume_release_metadata() to
accept btrfs_root, and record the qgroup_to_release number, and call
btrfs_qgroup_convert_reserved_meta() for it.
Fixes: 733e03a0b2 ("btrfs: qgroup: Split meta rsv type into meta_prealloc and meta_pertrans")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There's no practical reason too use 'err' as a variable to convey
errors. In fact it's value is either set explicitly in the beginning of
the function or it simply takes the value of 'ret'. Not conforming to
the usual pattern of having ret be the only variable used to convey
errors makes the code more error prone to bugs. In fact one such bug
was introduced by 6bf9e4bd6a ("btrfs: inode: Verify inode mode toi
avoid NULL pointer dereference") by assigning the error value to 'ret'
and not 'err'.
Let's fix that issue and make the function less tricky by leaving only
ret to convey error values.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
iomap dio will run generic_write_sync() for us if the iocb is DSYNC.
This is problematic for us because of 2 reasons:
1. we hold the inode_lock() during this operation, and we take it in
generic_write_sync()
2. we hold a read lock on the dio_sem but take the write lock in fsync
Since we don't want to rip out this code right now, but reworking the
locking is a bit much to do at this point, work around this problem with
this masterpiece of a patch.
First, we clear DSYNC on the iocb so that the iomap stuff doesn't know
that it needs to handle the sync. We save this fact in
current->journal_info, because we need to see do special things once
we're in iomap_begin, and we have no way to pass private information
into iomap_dio_rw().
Next we specify a separate iomap_dio_ops for sync, which implements an
->end_io() callback that gets called when the dio completes. This is
important for AIO, because we really do need to run generic_write_sync()
if we complete asynchronously. However if we're still in the submitting
context when we enter ->end_io() we clear the flag so that the submitter
knows they're the ones that needs to run generic_write_sync().
This is meant to be temporary. We need to work out how to eliminate the
inode_lock() and the dio_sem in our fsync and use another mechanism to
protect these operations.
Tested-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We're using direct io implementation based on buffer heads. This patch
switches to the new iomap infrastructure.
Switch from __blockdev_direct_IO() to iomap_dio_rw(). Rename
btrfs_get_blocks_direct() to btrfs_dio_iomap_begin() and use it as
iomap_begin() for iomap direct I/O functions. This function allocates
and locks all the blocks required for the I/O. btrfs_submit_direct() is
used as the submit_io() hook for direct I/O ops.
Since we need direct I/O reads to go through iomap_dio_rw(), we change
file_operations.read_iter() to a btrfs_file_read_iter() which calls
btrfs_direct_IO() for direct reads and falls back to
generic_file_buffered_read() for incomplete reads and buffered reads.
We don't need address_space.direct_IO() anymore: set it to noop.
Similarly, we don't need flags used in __blockdev_direct_IO(). iomap is
capable of direct I/O reads from a hole, so we don't need to return
-ENOENT.
Btrfs direct I/O is now done under i_rwsem, shared in case of reads and
exclusive in case of writes. This guards against simultaneous truncates.
Use iomap->iomap_end() to check for failed or incomplete direct I/O:
- for writes, call __endio_write_update_ordered()
- for reads, unlock extents
btrfs_dio_data is now hooked in iomap->private and not
current->journal_info. It carries the reservation variable and the
amount of data submitted, so we can calculate the amount of data to call
__endio_write_update_ordered in case of an error.
This patch removes last use of struct buffer_head from btrfs.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since commit d4682ba03e ("Btrfs: sync log after logging new name") we
started to commit logs, and fallback to transaction commits when we failed
to log the new names or commit the logs, after link and rename operations
when the target inodes (or their parents) were previously logged in the
current transaction. This was to avoid losing directories despite an
explicit fsync on them when they are ancestors of some inode that got a
new named logged, due to a link or rename operation. However that adds the
cost of starting IO and waiting for it to complete, which can cause higher
latencies for applications.
Instead of doing that, just make sure that when we log a new name for an
inode we don't mark any of its ancestors as logged, so that if any one
does an fsync against any of them, without doing any other change on them,
the fsync commits the log. This way we only pay the cost of a log commit
(or a transaction commit if something goes wrong or a new block group was
created) if the application explicitly asks to fsync any of the parent
directories.
Using dbench, which mixes several filesystems operations including renames,
revealed some significant latency gains. The following script that uses
dbench was used to test this:
#!/bin/bash
DEV=/dev/nvme0n1
MNT=/mnt/btrfs
MOUNT_OPTIONS="-o ssd -o space_cache=v2"
MKFS_OPTIONS="-m single -d single"
THREADS=16
echo "performance" | tee /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
mkfs.btrfs -f $MKFS_OPTIONS $DEV
mount $MOUNT_OPTIONS $DEV $MNT
dbench -t 300 -D $MNT $THREADS
umount $MNT
The test was run on bare metal, no virtualization, on a box with 12 cores
(Intel i7-8700), 64Gb of RAM and using a NVMe device, with a kernel
configuration that is the default of typical distributions (debian in this
case), without debug options enabled (kasan, kmemleak, slub debug, debug
of page allocations, lock debugging, etc).
Results before this patch:
Operation Count AvgLat MaxLat
----------------------------------------
NTCreateX 10750455 0.011 155.088
Close 7896674 0.001 0.243
Rename 455222 2.158 1101.947
Unlink 2171189 0.067 121.638
Deltree 256 2.425 7.816
Mkdir 128 0.002 0.003
Qpathinfo 9744323 0.006 21.370
Qfileinfo 1707092 0.001 0.146
Qfsinfo 1786756 0.001 11.228
Sfileinfo 875612 0.003 21.263
Find 3767281 0.025 9.617
WriteX 5356924 0.011 211.390
ReadX 16852694 0.003 9.442
LockX 35008 0.002 0.119
UnlockX 35008 0.001 0.138
Flush 753458 4.252 1102.249
Throughput 1128.35 MB/sec 16 clients 16 procs max_latency=1102.255 ms
Results after this patch:
16 clients, after
Operation Count AvgLat MaxLat
----------------------------------------
NTCreateX 11471098 0.012 448.281
Close 8426396 0.001 0.925
Rename 485746 0.123 267.183
Unlink 2316477 0.080 63.433
Deltree 288 2.830 11.144
Mkdir 144 0.003 0.010
Qpathinfo 10397420 0.006 10.288
Qfileinfo 1822039 0.001 0.169
Qfsinfo 1906497 0.002 14.039
Sfileinfo 934433 0.004 2.438
Find 4019879 0.026 10.200
WriteX 5718932 0.011 200.985
ReadX 17981671 0.003 10.036
LockX 37352 0.002 0.076
UnlockX 37352 0.001 0.109
Flush 804018 5.015 778.033
Throughput 1201.98 MB/sec 16 clients 16 procs max_latency=778.036 ms
(+6.5% throughput, -29.4% max latency, -75.8% rename latency)
Test case generic/498 from fstests tests the scenario that the previously
mentioned commit fixed.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In btrfs_orphan_cleanup, there's another instance of fs_info, but it's
the same as the one we already have.
In btrfs_backref_finish_upper_links, rb_node is same type and used
as temporary cursor to the tree.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We have btrfs_wait_ordered_roots() which takes a u64 for nr, but
btrfs_start_delalloc_roots() that takes an int for nr, which makes using
them in conjunction, especially for something like (u64)-1, annoying and
inconsistent. Fix btrfs_start_delalloc_roots() to take a u64 for nr and
adjust start_delalloc_inodes() and it's callers appropriately.
This means we've adjusted start_delalloc_inodes() to take a pointer of
nr since we want to preserve the ability for start-delalloc_inodes() to
return an error, so simply make it do the nr adjusting as necessary.
Part of adjusting the callers to this means changing
btrfs_writeback_inodes_sb_nr() to take a u64 for items. This may be
confusing because it seems unrelated, but the caller of
btrfs_writeback_inodes_sb_nr() already passes in a u64, it's just the
function variable that needs to be changed.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Tested-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
That BUG_ON cannot ever trigger because as the comment there states -
'err' is always set. Simply remove it as it brings no value.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=ONgI
-----END PGP SIGNATURE-----
Merge tag 'for-5.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix swapfile activation on subvolumes with deleted snapshots
- error value mixup when removing directory entries from tree log
- fix lzo compression level reset after previous level setting
- fix space cache memory leak after transaction abort
- fix const function attribute
- more error handling improvements
* tag 'for-5.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: detect nocow for swap after snapshot delete
btrfs: check the right error variable in btrfs_del_dir_entries_in_log
btrfs: fix space cache memory leak after transaction abort
btrfs: use the correct const function attribute for btrfs_get_num_csums
btrfs: reset compression level for lzo on remount
btrfs: handle errors from async submission
can_nocow_extent and btrfs_cross_ref_exist both rely on a heuristic for
detecting a must cow condition which is not exactly accurate, but saves
unnecessary tree traversal. The incorrect assumption is that if the
extent was created in a generation smaller than the last snapshot
generation, it must be referenced by that snapshot. That is true, except
the snapshot could have since been deleted, without affecting the last
snapshot generation.
The original patch claimed a performance win from this check, but it
also leads to a bug where you are unable to use a swapfile if you ever
snapshotted the subvolume it's in. Make the check slower and more strict
for the swapon case, without modifying the general cow checks as a
compromise. Turning swap on does not seem to be a particularly
performance sensitive operation, so incurring a possibly unnecessary
btrfs_search_slot seems worthwhile for the added usability.
Note: Until the snapshot is competely cleaned after deletion,
check_committed_refs will still cause the logic to think that cow is
necessary, so the user must until 'btrfs subvolu sync' finished before
activating the swapfile swapon.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Btrfs' async submit mechanism is able to handle errors in the submission
path and the meta-data async submit function correctly passes the error
code to the caller.
In btrfs_submit_bio_start() and btrfs_submit_bio_start_direct_io() we're
not handling the errors returned by btrfs_csum_one_bio() correctly though
and simply call BUG_ON(). This is unnecessary as the caller of these two
functions - run_one_async_start - correctly checks for the return values
and sets the status of the async_submit_bio. The actual bio submission
will be handled later on by run_one_async_done only if
async_submit_bio::status is 0, so the data won't be written if we
encountered an error in the checksum process.
Simply return the error from btrfs_csum_one_bio() to the async submitters,
like it's done in btree_submit_bio_start().
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=7b8U
-----END PGP SIGNATURE-----
Merge tag 'for-5.9-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs updates from David Sterba:
"One minor update, the rest are fixes that have arrived a bit late for
the first batch. There are also some recent fixes for bugs that were
discovered during the merge window and pop up during testing.
User visible change:
- show correct subvolume path in /proc/mounts for bind mounts
Fixes:
- fix compression messages when remounting with different level or
compression algorithm
- tree-log: fix some memory leaks on error handling paths
- restore I_VERSION on remount
- fix return values and error code mixups
- fix umount crash with quotas enabled when removing sysfs files
- fix trim range on a shrunk device"
* tag 'for-5.9-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: trim: fix underflow in trim length to prevent access beyond device boundary
btrfs: fix return value mixup in btrfs_get_extent
btrfs: sysfs: fix NULL pointer dereference at btrfs_sysfs_del_qgroups()
btrfs: check correct variable after allocation in btrfs_backref_iter_alloc
btrfs: make sure SB_I_VERSION doesn't get unset by remount
btrfs: fix memory leaks after failure to lookup checksums during inode logging
btrfs: don't show full path of bind mounts in subvol=
btrfs: fix messages after changing compression level by remount
btrfs: only search for left_info if there is no right_info in try_merge_free_space
btrfs: inode: fix NULL pointer dereference if inode doesn't need compression
btrfs_get_extent() sets variable ret, but out: error path expect error
to be in variable err so the error code is lost.
Fixes: 6bf9e4bd6a ("btrfs: inode: Verify inode mode to avoid NULL pointer dereference")
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
There is a bug report of NULL pointer dereference caused in
compress_file_extent():
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Workqueue: btrfs-delalloc btrfs_delalloc_helper [btrfs]
NIP [c008000006dd4d34] compress_file_range.constprop.41+0x75c/0x8a0 [btrfs]
LR [c008000006dd4d1c] compress_file_range.constprop.41+0x744/0x8a0 [btrfs]
Call Trace:
[c000000c69093b00] [c008000006dd4d1c] compress_file_range.constprop.41+0x744/0x8a0 [btrfs] (unreliable)
[c000000c69093bd0] [c008000006dd4ebc] async_cow_start+0x44/0xa0 [btrfs]
[c000000c69093c10] [c008000006e14824] normal_work_helper+0xdc/0x598 [btrfs]
[c000000c69093c80] [c0000000001608c0] process_one_work+0x2c0/0x5b0
[c000000c69093d10] [c000000000160c38] worker_thread+0x88/0x660
[c000000c69093db0] [c00000000016b55c] kthread+0x1ac/0x1c0
[c000000c69093e20] [c00000000000b660] ret_from_kernel_thread+0x5c/0x7c
---[ end trace f16954aa20d822f6 ]---
[CAUSE]
For the following execution route of compress_file_range(), it's
possible to hit NULL pointer dereference:
compress_file_extent()
|- pages = NULL;
|- start = async_chunk->start = 0;
|- end = async_chunk = 4095;
|- nr_pages = 1;
|- inode_need_compress() == false; <<< Possible, see later explanation
| Now, we have nr_pages = 1, pages = NULL
|- cont:
|- ret = cow_file_range_inline();
|- if (ret <= 0) {
|- for (i = 0; i < nr_pages; i++) {
|- WARN_ON(pages[i]->mapping); <<< Crash
To enter above call execution branch, we need the following race:
Thread 1 (chattr) | Thread 2 (writeback)
--------------------------+------------------------------
| btrfs_run_delalloc_range
| |- inode_need_compress = true
| |- cow_file_range_async()
btrfs_ioctl_set_flag() |
|- binode_flags |= |
BTRFS_INODE_NOCOMPRESS |
| compress_file_range()
| |- inode_need_compress = false
| |- nr_page = 1 while pages = NULL
| | Then hit the crash
[FIX]
This patch will fix it by checking @pages before doing accessing it.
This patch is only designed as a hot fix and easy to backport.
More elegant fix may make btrfs only check inode_need_compress() once to
avoid such race, but that would be another story.
Reported-by: Luciano Chavez <chavez@us.ibm.com>
Fixes: 4d3a800ebb ("btrfs: merge nr_pages input and output parameter in compress_pages")
CC: stable@vger.kernel.org # 4.14.x: cecc8d9038: btrfs: Move free_pages_out label in inline extent handling branch in compress_file_range
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Pull misc vfs updates from Al Viro:
"No common topic whatsoever in those, sorry"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: define inode flags using bit numbers
iov_iter: Move unnecessary inclusion of crypto/hash.h
dlmfs: clean up dlmfs_file_{read,write}() a bit
The possibility of extents being shared (through clone and deduplication
operations) requires special care when logging data checksums, to avoid
having a log tree with different checksum items that cover ranges which
overlap (which resulted in missing checksums after replaying a log tree).
Such problems were fixed in the past by the following commits:
commit 40e046acbd ("Btrfs: fix missing data checksums after replaying a
log tree")
commit e289f03ea7 ("btrfs: fix corrupt log due to concurrent fsync of
inodes with shared extents")
Test case generic/588 exercises the scenario solved by the first commit
(purely sequential and deterministic) while test case generic/457 often
triggered the case fixed by the second commit (not deterministic, requires
specific timings under concurrency).
The problems were addressed by deleting, from the log tree, any existing
checksums before logging the new ones. And also by doing the deletion and
logging of the cheksums while locking the checksum range in an extent io
tree (root->log_csum_range), to deal with the case where we have concurrent
fsyncs against files with shared extents.
That however causes more contention on the leaves of a log tree where we
store checksums (and all the nodes in the paths leading to them), even
when we do not have shared extents, or all the shared extents were created
by past transactions. It also adds a bit of contention on the spin lock of
the log_csums_range extent io tree of the log root.
This change adds a 'last_reflink_trans' field to the inode to keep track
of the last transaction where a new extent was shared between inodes
(through clone and deduplication operations). It is updated for both the
source and destination inodes of reflink operations whenever a new extent
(created in the current transaction) becomes shared by the inodes. This
field is kept in memory only, not persisted in the inode item, similar
to other existing fields (last_unlink_trans, logged_trans).
When logging checksums for an extent, if the value of 'last_reflink_trans'
is smaller then the current transaction's generation/id, we skip locking
the extent range and deletion of checksums from the log tree, since we
know we do not have new shared extents. This reduces contention on the
log tree's leaves where checksums are stored.
The following script, which uses fio, was used to measure the impact of
this change:
$ cat test-fsync.sh
#!/bin/bash
DEV=/dev/sdk
MNT=/mnt/sdk
MOUNT_OPTIONS="-o ssd"
MKFS_OPTIONS="-d single -m single"
if [ $# -ne 3 ]; then
echo "Use $0 NUM_JOBS FILE_SIZE FSYNC_FREQ"
exit 1
fi
NUM_JOBS=$1
FILE_SIZE=$2
FSYNC_FREQ=$3
cat <<EOF > /tmp/fio-job.ini
[writers]
rw=write
fsync=$FSYNC_FREQ
fallocate=none
group_reporting=1
direct=0
bs=64k
ioengine=sync
size=$FILE_SIZE
directory=$MNT
numjobs=$NUM_JOBS
EOF
echo "Using config:"
echo
cat /tmp/fio-job.ini
echo
mkfs.btrfs -f $MKFS_OPTIONS $DEV
mount $MOUNT_OPTIONS $DEV $MNT
fio /tmp/fio-job.ini
umount $MNT
The tests were performed for different numbers of jobs, file sizes and
fsync frequency. A qemu VM using kvm was used, with 8 cores (the host has
12 cores, with cpu governance set to performance mode on all cores), 16GiB
of ram (the host has 64GiB) and using a NVMe device directly (without an
intermediary filesystem in the host). While running the tests, the host
was not used for anything else, to avoid disturbing the tests.
The obtained results were the following (the last line of fio's output was
pasted). Starting with 16 jobs is where a significant difference is
observable in this particular setup and hardware (differences highlighted
below). The very small differences for tests with less than 16 jobs are
possibly just noise and random.
**** 1 job, file size 1G, fsync frequency 1 ****
before this change:
WRITE: bw=23.8MiB/s (24.9MB/s), 23.8MiB/s-23.8MiB/s (24.9MB/s-24.9MB/s), io=1024MiB (1074MB), run=43075-43075msec
after this change:
WRITE: bw=24.4MiB/s (25.6MB/s), 24.4MiB/s-24.4MiB/s (25.6MB/s-25.6MB/s), io=1024MiB (1074MB), run=41938-41938msec
**** 2 jobs, file size 1G, fsync frequency 1 ****
before this change:
WRITE: bw=37.7MiB/s (39.5MB/s), 37.7MiB/s-37.7MiB/s (39.5MB/s-39.5MB/s), io=2048MiB (2147MB), run=54351-54351msec
after this change:
WRITE: bw=37.7MiB/s (39.5MB/s), 37.6MiB/s-37.6MiB/s (39.5MB/s-39.5MB/s), io=2048MiB (2147MB), run=54428-54428msec
**** 4 jobs, file size 1G, fsync frequency 1 ****
before this change:
WRITE: bw=67.5MiB/s (70.8MB/s), 67.5MiB/s-67.5MiB/s (70.8MB/s-70.8MB/s), io=4096MiB (4295MB), run=60669-60669msec
after this change:
WRITE: bw=68.6MiB/s (71.0MB/s), 68.6MiB/s-68.6MiB/s (71.0MB/s-71.0MB/s), io=4096MiB (4295MB), run=59678-59678msec
**** 8 jobs, file size 1G, fsync frequency 1 ****
before this change:
WRITE: bw=128MiB/s (134MB/s), 128MiB/s-128MiB/s (134MB/s-134MB/s), io=8192MiB (8590MB), run=64048-64048msec
after this change:
WRITE: bw=129MiB/s (135MB/s), 129MiB/s-129MiB/s (135MB/s-135MB/s), io=8192MiB (8590MB), run=63405-63405msec
**** 16 jobs, file size 1G, fsync frequency 1 ****
before this change:
WRITE: bw=78.5MiB/s (82.3MB/s), 78.5MiB/s-78.5MiB/s (82.3MB/s-82.3MB/s), io=16.0GiB (17.2GB), run=208676-208676msec
after this change:
WRITE: bw=110MiB/s (115MB/s), 110MiB/s-110MiB/s (115MB/s-115MB/s), io=16.0GiB (17.2GB), run=149295-149295msec
(+40.1% throughput, -28.5% runtime)
**** 32 jobs, file size 1G, fsync frequency 1 ****
before this change:
WRITE: bw=58.8MiB/s (61.7MB/s), 58.8MiB/s-58.8MiB/s (61.7MB/s-61.7MB/s), io=32.0GiB (34.4GB), run=557134-557134msec
after this change:
WRITE: bw=76.1MiB/s (79.8MB/s), 76.1MiB/s-76.1MiB/s (79.8MB/s-79.8MB/s), io=32.0GiB (34.4GB), run=430550-430550msec
(+29.4% throughput, -22.7% runtime)
**** 64 jobs, file size 512M, fsync frequency 1 ****
before this change:
WRITE: bw=65.8MiB/s (68.0MB/s), 65.8MiB/s-65.8MiB/s (68.0MB/s-68.0MB/s), io=32.0GiB (34.4GB), run=498055-498055msec
after this change:
WRITE: bw=85.1MiB/s (89.2MB/s), 85.1MiB/s-85.1MiB/s (89.2MB/s-89.2MB/s), io=32.0GiB (34.4GB), run=385116-385116msec
(+29.3% throughput, -22.7% runtime)
**** 128 jobs, file size 256M, fsync frequency 1 ****
before this change:
WRITE: bw=54.7MiB/s (57.3MB/s), 54.7MiB/s-54.7MiB/s (57.3MB/s-57.3MB/s), io=32.0GiB (34.4GB), run=599373-599373msec
after this change:
WRITE: bw=121MiB/s (126MB/s), 121MiB/s-121MiB/s (126MB/s-126MB/s), io=32.0GiB (34.4GB), run=271907-271907msec
(+121.2% throughput, -54.6% runtime)
**** 256 jobs, file size 256M, fsync frequency 1 ****
before this change:
WRITE: bw=69.2MiB/s (72.5MB/s), 69.2MiB/s-69.2MiB/s (72.5MB/s-72.5MB/s), io=64.0GiB (68.7GB), run=947536-947536msec
after this change:
WRITE: bw=121MiB/s (127MB/s), 121MiB/s-121MiB/s (127MB/s-127MB/s), io=64.0GiB (68.7GB), run=541916-541916msec
(+74.9% throughput, -42.8% runtime)
**** 512 jobs, file size 128M, fsync frequency 1 ****
before this change:
WRITE: bw=85.4MiB/s (89.5MB/s), 85.4MiB/s-85.4MiB/s (89.5MB/s-89.5MB/s), io=64.0GiB (68.7GB), run=767734-767734msec
after this change:
WRITE: bw=141MiB/s (147MB/s), 141MiB/s-141MiB/s (147MB/s-147MB/s), io=64.0GiB (68.7GB), run=466022-466022msec
(+65.1% throughput, -39.3% runtime)
**** 1024 jobs, file size 128M, fsync frequency 1 ****
before this change:
WRITE: bw=115MiB/s (120MB/s), 115MiB/s-115MiB/s (120MB/s-120MB/s), io=128GiB (137GB), run=1143775-1143775msec
after this change:
WRITE: bw=171MiB/s (180MB/s), 171MiB/s-171MiB/s (180MB/s-180MB/s), io=128GiB (137GB), run=764843-764843msec
(+48.7% throughput, -33.1% runtime)
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that btrfs_io_bio have access to btrfs_device we can safely
increment the device corruption counter on error. There is one notable
exception - repair bios for raid. Since those don't go through the
normal submit_stripe_bio callpath but through raid56_parity_recover thus
repair bios won't have their device set.
Scrub increments the corruption counter for checksum mismatch as well
but does not call this function.
Link: https://lore.kernel.org/linux-btrfs/4857863.FCrPRfMyHP@liv/
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
When a lot of subvolumes are created, there is a user report about
transaction aborted caused by slow anonymous block device reclaim:
BTRFS: Transaction aborted (error -24)
WARNING: CPU: 17 PID: 17041 at fs/btrfs/transaction.c:1576 create_pending_snapshot+0xbc4/0xd10 [btrfs]
RIP: 0010:create_pending_snapshot+0xbc4/0xd10 [btrfs]
Call Trace:
create_pending_snapshots+0x82/0xa0 [btrfs]
btrfs_commit_transaction+0x275/0x8c0 [btrfs]
btrfs_mksubvol+0x4b9/0x500 [btrfs]
btrfs_ioctl_snap_create_transid+0x174/0x180 [btrfs]
btrfs_ioctl_snap_create_v2+0x11c/0x180 [btrfs]
btrfs_ioctl+0x11a4/0x2da0 [btrfs]
do_vfs_ioctl+0xa9/0x640
ksys_ioctl+0x67/0x90
__x64_sys_ioctl+0x1a/0x20
do_syscall_64+0x5a/0x110
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace 33f2f83f3d5250e9 ]---
BTRFS: error (device sda1) in create_pending_snapshot:1576: errno=-24 unknown
BTRFS info (device sda1): forced readonly
BTRFS warning (device sda1): Skipping commit of aborted transaction.
BTRFS: error (device sda1) in cleanup_transaction:1831: errno=-24 unknown
[CAUSE]
The anonymous device pool is shared and its size is 1M. It's possible to
hit that limit if the subvolume deletion is not fast enough and the
subvolumes to be cleaned keep the ids allocated.
[WORKAROUND]
We can't avoid the anon device pool exhaustion but we can shorten the
time the id is attached to the subvolume root once the subvolume becomes
invisible to the user.
Reported-by: Greed Rong <greedrong@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/CA+UqX+NTrZ6boGnWHhSeZmEY5J76CTqmYjO2S+=tHJX7nb9DPw@mail.gmail.com/
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
vfs_inode is used only for the inode number everything else requires
btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ use btrfs_ino ]
Signed-off-by: David Sterba <dsterba@suse.com>
Instead of making multiple calls to BTRFS_I simply take btrfs_inode as
an input paramter.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All of its children functions use btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All of its children take btrfs_inode so bubble up this requirement to
btrfs_delalloc_reserve_space's interface and stop calling BTRFS_I
internally.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead of calling BTRFS_I on the passed vfs_inode take btrfs_inode
directly.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It needs btrfs_inode so take it as a parameter directly.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It only uses btrfs_inode internally so take it as a parameter.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
No point in taking an inode only to get btrfs_fs_info from it, instead
take btrfs_fs_info directly.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Preparation to make btrfs_dirty_pages take btrfs_inode as parameter.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function really needs a btrfs_inode and not a generic vfs one. Take
it as a parameter and get rid of superfluous BTRFS_I() calls.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Take btrfs_inode directly and stop using superfulous BTRFS_I calls.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Simply forwards its argument so let's get rid of one extra BTRFS_I by
taking btrfs_inode directly.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All children now take btrfs_inode so convert it to taking it as a
parameter as well.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Gets rid of superfulous BTRFS_I() calls and prepare for converting
btrfs_run_delalloc_range to using btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Simply gets rid of superfluous BTRFS_I() calls.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Gets rid of superfluous BTRFS_I() calls.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Preparation to converting btrfs_run_delalloc_range to using btrfs_inode
without BTRFS_I() calls.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It really wants btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It doesn't really need vfs_inode but btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It only uses vfs inode for assigning it to the async_chunk function.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It only really uses btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It really wants btrfs_inode and is prepration to converting
run_delalloc_nocow to taking btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It just forwards its argument to __btrfs_qgroup_release_data.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All but 3 uses require vfs_inode so convert the logic to have
btrfs_inode be the main inode struct.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Majority of its uses are for btrfs_inode so take it as an argument
directly.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It simpy forwards its inode argument to __btrfs_add_ordered_extent which
already takes btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All its children functions take btrfs_inode so convert it to taking
btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Preparation to converting its callers to taking btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It has only 2 uses for the vfs_inode - insert_inline_extent and
i_size_read. On the flipside it will allow converting its callers to
btrfs_inode, so convert it to taking btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It passes btrfs_inode to its callee so change the interface.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The function btrfs_check_can_nocow() now has two completely different
call patterns.
For nowait variant, callers don't need to do any cleanup. While for
wait variant, callers need to release the lock if they can do nocow
write.
This is somehow confusing, and is already a problem for the exported
btrfs_check_can_nocow().
So this patch will separate the different patterns into different
functions.
For nowait variant, the function will be called check_nocow_nolock().
For wait variant, the function pair will be btrfs_check_nocow_lock()
btrfs_check_nocow_unlock().
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
