Bumping DC version for DMU FW fix
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt would not be enabled promptly if a pipe is disabled
and re-enabled, causing flip_done timeout error during DP
compliance tests
[How]
Enable pflip interrupt upon pipe enablement
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.
[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating. Add additional delay
time for single rank dimm.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Some existing DC interfaces are optimized to return a single eDP
link/stream. Refactored those DC interfaces to support multiple eDP.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To process AUX transactions with DMUB using inbox1 and outbox1 mail boxes.
[HOW]
1) Added inbox1 command DMUB_CMD__DP_AUX_ACCESS to issue AUX commands
to DMUB in dc_process_dmub_aux_transfer_async(). DMUB processes AUX cmd
with DCN and sends reply back in an outbox1 message triggering an
outbox1 interrupt to driver.
2) In existing driver implementation, AUX commands are processed
synchronously by configuring DCN reg. But in DMUB AUX, driver sends an
inbox1 message and waits for a conditional variable (CV) which will be
signaled by outbox1 ISR.
3) As the driver holds dal and dc locks while waiting for CV, the outbox1
ISR is registered with noMutexWait set to true, which allows ISR to run
and signal CV. This sets a constraint on ISR to not modify variables
such as dc, dmub, etc.
4) Created dmub_outbox.c with dmub_enable_outbox_notification() to enable
outbox1 mailbox.
5) New mailbox address ranges allocated for outbox1 of size DMUB_RB_SIZE.
Created dmub functions for Outbox1: dmub_dcn20_setup_out_mailbox(),
dmub_dcn20_get_outbox1_wptr() and dmub_dcn20_set_outbox1_rptr().
6) Added functions dc_stat_get_dmub_notification() and
dmub_srv_stat_get_notification() to retrieve Outbox1 message.
7) Currently, DMUB doesn't opens DDC in AUX mode before issuing AUX
transaction. A workaround is added in dce_aux_transfer_dmub_raw() to
open in DDC in AUX mode for every AUX transaction.
8) Added dc debug option enable_dmub_aux_for_legacy_ddc enable/disable
DMUB AUX. This debug option is checked dce_aux_transfer_with_retries()
to select the method to process AUX transactions.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vendor based fan noise improvement
[how]
Report timing synchronizable when DP streams time frame
difference is less than 0.05 percent. Adjust DP DTOs and
sync displays using MASTER_UPDATE_LOCK_DB_X_Y
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.123 brings improvements in multiple areas.
In summary, we highlight:
- Firmware release 0.0.52
- Bug fixes on MPC OGAM sequence, display experience, etc.
- Improvements on timing, transmitter control, etc.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In following sequence driver will add counter twice on
same edp stream.
1. Boot into OS.
2. Set timing with edp only.
3. Set timing with edp and external monitor.
4. Set visibility on for edp.
Step 2 and 3 will add seamless boot counter twice and
subtract it once in step 4.
[How]
Remove global counter and calculate it is used.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fix error handling in dc/dcn10/dcn10_hw_sequencer_debug.c
- DIO Supported for virtual displays
- memset dmub_rb_cmd to 0 which fixes issues talking with firmware
- fix 64bit division issue on 32bit OS
- move edp sink present detection to hw init to fix hang
- reverts a patch that caused 3x4K60 displays over MST
with DSC enabled to not light up
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Better handling of dummy p-state table
- Workaround for some legacy DP-VGA dongles
- Add Freesync HDMI support to DMCU
- Enable "trigger_hotplug" debugfs on all outputs
- fix initial bounding box values for dcn3.02
- implement support for DID2.0 dsc passthrough
- fix calculation for the pwl backlight curve
- Fix multiple memory leaks
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Overlay won't move to a new positon if viewport size is smaller than
what can be handled. It'd either disappear or stay at the old
position. This condition is for example hit if overlay is moved too
much outside of left or top edge of the screen, but it applies to
any non-cursor plane type.
[how]
Reject this contidion at validation time. This gives the calling
level a chance to handle this gracefully and avoid inconsistent
behaivor.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Remove force_ignore_link_settings debug option as it is no longer used.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This DC update brings improvements in multiple areas. In summary, we highlight:
- Fix display detection on HDMI ComboPHY
- Drop SOC bounding box hookup
- Fix DPCD values
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There aren't any ASIC where we use these binaries and they aren't
useful for future use since it's inconvenient to extend and maintain
these structures.
[How]
Drop the support from DM and DC for now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the function for idle optimizations
-remove hardcoded size
-enable no memory-request case
-add cursor copy
-update mall eligibility check case
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we use the maximum possible cursor cache size when deciding if we
should attempt to enable MALL, but this prevents us from enabling the
feature for certain key use cases.
[How]
- consider cursor bpp when calculating if the cursor fits
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DSCL memory blocks should be powered down when they're not in use.
This will reduce power consumption.
[How]
1. Write to DSCL_MEM_PWR_FORCE to put memory to shutdown when DSCL is not
used.
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
only apply multiple display power optimization in case there are more
than one internal display.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some platforms, DMCU is no longer used. In these cases, some DMCU
memory should be completely powered off to save power.
[How]
1. Set DMCU_ERAM_MEM_PWR_FORCE to shutdown memory when DMCU is not in
use
2. Added a debug option to allow this behaviour to be turned off
3. Set all memory low power debug options to off first, to not
immediately cause problems
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should use int for counting variable
[How]
Change type from bool to uint32_t
Signed-off-by: Raymond Yang <rayyang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The I2C memory blocks should be powered down when they are not in use.
This will reduce power consumption.
[How]
1. Write to I2C_LIGHT_SLEEP_FORCE to put memory in light sleep when
released
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Check if the eDP sink supports the dynamic backlight control
[How]
Query the dynamic backlight capability in DPCD (eDP case only)
Signed-off-by: Roy Chan <roy.chan@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Actual dpp/disp clock PMFW set are always equal or more than requested.
Need to cache the actual clock for debugging purpose.
[How]
Add actuall dpp/disp clk in clock manager and save it when set clocks.
Add an ASSERT in case of actual clock less than requested.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.
[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoids confusion in configurations.
v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The OPTC memory blocks should be powered down when they are not in use.
This will reduce power consumption.
[How]
1. Set ODM_MEM_UNASSIGNED_PWR_MODE to shutdown memory when unassigned
2. Set ODM_MEM_VBLANK_PWR_MODE to light sleep mode when in vblank
3. Added a debug option to allow this behaviour to be turned off
4. Restructured debug options to use a bitfield in a way that's more clear
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The MPC memory blocks in DCN3 should be powered down completely when
they are not in use. This will reduce power consumption.
[How]
This commits changes behaviour for dcn3 and does the following:
1. Write to MPC_RMU<X>_LOW_PWR_MODE and MPCC_OGAM_MEM_LOW_PWR_MODE to
automatically shut down memory when not in use
2. mpc3_power_on_shaper_3dlut and mpc3_power_on_ogam_lut are called
to disable force power on when configuration finishes
3. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.
[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Functions (disable_all_writeback_pipes_for_stream &
dc_enable_stereo & dc_post_update_surfaces_to_stream)
always return true, there is no need to keep the return value.
This change is to make the code a bit more readable.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.
This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During driver unload, it is expected that p-state switching is supported.
If it's not supported, PMFW will hang due to a forced p-state switch. Even
if the current timing does not support p-state normally, we still want to
force allow because the worst that can happen is underflow. This will
match Navi10 behaviour.
[How]
- new hubbub func to control the force pstate register
- force allow when releasing display ownership
- registers are inaccessible after due to m_cgs.hwNotAvailable
- explicitly disable force signal during hw_init
- if driver is disabled and re-enabled, register not cleared otherwise
Also, remove DCN3 part of dcn10_init_hw, we will not be going back to it.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
At the moment, some tests are failing because cur_link_settings is
invalid. As a workaround, add an option to force dio disable.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The ctx field of dc_transfer_func is not always populated and therefore
isn't reliable.
[How]
Remove dc context from dc_transfer_func
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
with eDP + DP, each display use one pipe. after DP unplugged, eDP switch
from one pipe to two pipes -- pipe split. dpp1_cm_set_regamma_pwl will
be executed too. The duration from switch single pipe to dual pipes is a
little long which could let eDP enter PSR mode. upon two pipes for eDP
are setup, eDP PHY is disabled. front pipe is not really running to
fetch data from frame buffer. i.e., dchubp is not in normal working
status. execution of hubbub1_wm_change_req_wa may cause p-state warning.
[How]
disable eDP PSR before dc_commit_state. psr is disabled when execute
hubbub1_wm_change_req_wa.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Implement an interface to obtain plane size caps
[How]
Add min_width, min_height fields to dc_plane_cap structure.
Set values to 16x16 for discrete ASICs, and 64x64 for others.
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless systems, if set mode is not called, hardware will not be
powered down on boot, causing HW/SW discrepancies. Powering down
hardware on boot will ensure SW state is accurate.
[HOW]
Set a timer callback on boot for 10 seconds. If set mode is not called
within that time, power down hardware. Otherwise, do not power down.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Register key for AE or QA do regression test. New edid status for
check.
[How]
Add register key edid_read_retry_times.
Add new edid status EDID_FALL_BACK.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.
[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And set back to 400us if LTTPR feature is not enabled.
We will set 3.2ms and always enable LTTPR non transparent mode
if LTTPR feature is enabled and LTTPR is present.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is using pixelclk AVFS for dppclk, that would cause issue.
[How]
To use dispclk AVFS for both dispclk and dppclk. There would choose
dppclk for request voltage when dispclk wouldn't be updated case. If
dispclk need to be updated, then it'll choose the bigger one from dppclk
and dispclk for request voltage.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC is very fast at link training and stream enablement
which causes issues such as blackscreens for non-compliant
monitors.
[How]
After debugging with scaler vendors we implement the
minimum delays at the necessary locations to ensure
the monitor does not hang. Delays are generic due to
lack of IEEE OUI information on the failing displays.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The change causes some regression in a common use case.
Will need more investigation before fixing the original issue.
[how]
This reverts commit fb8cf277b1.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sprcified monitor scalar cannot recognize timing
change on demand. Once the link phy disable and enable
during a short period then the Sink protection mechanism
could keep the screen in blank and cannot be recoverred.
[How]
To add 100ms delay between enable link phy and link training.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for managing resources for DCN3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for handling of clocking relevant to the DCN3 block
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dal side nv12 wa has a lot of side effects.
KMD side wa is used, so this should be remove.
[How]
Removed wa from dal side.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.
[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And only set to 400us if LTTPR is not present.
Before this piece of logic is interwined with LTTPR support.
Now we will default to 3.2ms aux timeout even if LTTPR support is not
enabled by driver.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Want to make use of detile buffer of all 4 pipes to maximize amount of
data stored to hide certain memory latency cases.
[How]
In case of 1 plane and 1 stream, program 4 pipes to each retrieve 1/4 of
plane later mixed together by the MPCs. Added support for transition
from 4 to 1 MPC to 2 to 1 MPC or no pipe split case and vice versa.
Currently, only enabled if debug flag is set.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain display configurations we want to allow PSTATE
switch when one display can switch in VACTIVE and the
other display can switch in VBLANK
[How]
Add extra condition to dcn2 pstate support check
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
modules/color calculates various colour operations which are translated
to abstracted HW. DCE 5-12 had almost no important changes, but
starting with DCN1, every new generation comes with fairly major
differences in color pipeline.
We would hack it with some DCN checks, but a better approach is to
abstract color pipe capabilities so modules/DM can decide mapping to
HW block based on logical capabilities,
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging, it can be useful to be able to modify the dummy
p-state latency, this will make it easier to do so.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Backlight adjustment is tied to a specific display. So make the calls
target a link rather than making it a global state.
[How]
make all backlight calls link based
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Driver does not recognize new definitions of psr states.
- Internal tool is required for checking if psr is active.
[How]
- Parse psr state correctly so that driver will recognize psr state.
- Add visual confirmation that psr is active using existing mechanisms.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
