RTLX communication is based on lock-free shared memory buffers. It
happened to be working by luck so far but relies on the optimizer doing
certain optimizations but no reordering.
Fixed by inserting proper barriers in rtlx_read and rtlx_write, and careful
pointer dereferencing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 6d6671066a is incomplete and misses
non-r4k CPUs. This patch reverts the commit and fixes in other way.
o Do FCSR checking in caller of restore_fp_context.
o Send SIGFPE if the signal handler set any FPU exception bits.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have to make sure to use base-pagesize TLB entries even during the
early transition period where we need TLB miss handling but don't have
the kernel page tables setup yet for the linear region.
Also, it is necessary therefore to not use the 4MB TSB for these
translations, and instead use the normal kernel TSB. This allows us
to also get rid of the 4MB tsb for debug builds which shrinks the
kernel a little bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
The symbol is not actually used, but the compiler unforunately generates
a (unused) reference to it. This can happen even in modules. So export it.
Signed-off-by: Andi Kleen <ak@suse.de>
Fix the following section mismatch warnings on x86_64:
(build using defconfig)
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:mtrr_bp_init from .text between 'identify_cpu' (at offset 0x65eb) and 'IRQ0x20_interrupt'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data: from .text between 'finish_e820_parsing' (at offset 0x7dc2) and 'early_panic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:e820_print_map from .text between 'finish_e820_parsing' (at offset 0x7de1) and 'early_panic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:num_processors from .text between 'acpi_unmap_lsapic' (at offset 0xc88f) and 'acpi_register_ioapic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:disabled_cpus from .text between 'MP_processor_info' (at offset 0x11f35) and 'mp_register_lapic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:num_processors from .text between 'MP_processor_info' (at offset 0x11f6e) and 'mp_register_lapic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:num_processors from .text between 'MP_processor_info' (at offset 0x11f93) and 'mp_register_lapic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:fix_aperture from .text between 'gart_parse_options' (at offset 0x15517) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:fix_aperture from .text between 'gart_parse_options' (at offset 0x1552c) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_allowed from .text between 'gart_parse_options' (at offset 0x1553d) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_allowed from .text between 'gart_parse_options' (at offset 0x15552) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_allowed from .text between 'gart_parse_options' (at offset 0x15561) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_allowed from .text between 'gart_parse_options' (at offset 0x15577) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:fallback_aper_force from .text between 'gart_parse_options' (at offset 0x1558a) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:fallback_aper_order from .text between 'gart_parse_options' (at offset 0x155bf) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:timer_over_8254 from .text between 'ati_bugs' (at offset 0x16344) and 'via_bugs'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:timer_over_8254 from .text between 'ati_bugs' (at offset 0x16356) and 'via_bugs'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_allowed from .text between 'via_bugs' (at offset 0x16380) and 'nvidia_bugs'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_disabled from .text between 'via_bugs' (at offset 0x16397) and 'nvidia_bugs'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:acpi_use_timer_override from .text between 'nvidia_bugs' (at offset 0x163a7) and 'arch_unregister_cpu'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:nvidia_hpet_check from .text between 'nvidia_bugs' (at offset 0x163b1) and 'arch_unregister_cpu'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data: from .text between 'nvidia_bugs' (at offset 0x163be) and 'arch_unregister_cpu'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data: from .text between 'nvidia_bugs' (at offset 0x163d1) and 'arch_unregister_cpu'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:acpi_skip_timer_override from .text between 'nvidia_bugs' (at offset 0x163e1) and 'arch_unregister_cpu'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:quirk_intel_irqbalance from .text between 'intel_bugs' (at offset 0x1633c) and 'ati_bugs'
But adds:
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:get_mtrr_state from .text between 'mtrr_bp_init' (at offset 0xb887) and 'ipi_handler'
The warnings does not show up during a normal build due to kbuild
failing to check for section mismatch in vmlinux.
To see these warnings run:
scripts/mod/modpost arch/x86_64/kernel/built-in.o
kbuild will be fixed but the 'noise-level' had to be decresed first.
There remains a few section mismatch warnigns for x86_64 for areas where I did
not feel confident.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
VMI ROMs are pretty intimate to the kernel, so enforce their GPLness.
No \0 tricks checking for now
This rules out BSD/MIT modules for now, sorry -- the trouble is those
could come without source.
Acked-by: Zachary Amsden <zach@vmware.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix atomicity of TIF update in flush_thread() for powerpc
Fixes it correctly with *_ti_thread_flag.
Race :
parent process executing :
sys_ptrace()
(lock_kernel())
(ptrace_get_task_struct(pid))
arch_ptrace()
ptrace_detach()
ptrace_disable(child);
clear_singlestep(child);
clear_tsk_thread_flag(child, TIF_SINGLESTEP);
(which clears the TIF_SINGLESTEP flag atomically from a different
process)
(put_task_struct(child))
(unlock_kernel())
And at the same time, in the child process :
sys_execve()
do_execve()
search_binary_handler()
load_elf_binary()
flush_old_exec()
flush_thread()
doing a non-atomic thread flag update
Applies on 2.6.20.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
and no, it's not the case of "let's pull bits from underlying architecture"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PGALLOC_DMA is defined only if we have CONFIG_ZONE_DMA
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SH-3 and SH-4 were trampling the register, and SH-2 wasn't even
setting it in the first place. This ended up with some rather
broken behaviour in the sysrq show_regs().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A defconfig file and the 10 lines of code (including comments ...) that
are rotting since lmo commit 6516a42dc8b40c6c00010346dd51496125b16644
don't quite make proper support, so let's trash it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
72486f1f8f inverted the sense for
enabling hotplug CPU controls without reference to any other
architecture other than i386, ia64 and PowerPC. This left
everyone else without hotplug CPU control.
Fix ARM for this brain damage.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These pte loops all assume the passed in address is HPAGE
aligned, make sure that is actually true.
Signed-off-by: David S. Miller <davem@davemloft.net>
sys_mbind
sys_get_mempolicy
sys_set_mempolicy
sys_kexec_load
sys_move_pages
sys_getcpu
sys_epoll_pwait
This work is largely a result of David Woodhouse's most
excellent missing syscalls patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] sys_move_pages should be callable from an SPU
[POWERPC] Wire up sys_epoll_pwait
[POWERPC] Allocate syscall number for sys_getcpu
[POWERPC] update cell_defconfig
[POWERPC] ps3: always make sure were running on a PS3
[POWERPC] Fix spu SLB invalidations
[POWERPC] avoid SPU_ACTIVATE_NOWAKE optimization
[POWERPC] spufs: fix possible memory corruption is spufs_mem_write
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC]: Fix TIF_USEDFPU flag atomicity
[SPARC64]: Fix atomicity of TIF update in flush_thread()
[BW2]: Fix section mismatch warnings.
[CG14]: Fix section mismatch warnings.
[SPARC]: We do not need OLD_GETRLIMIT.
VMI is broken under COMPAT_VDSO, as Xen and other non hardware assisted
hypervisors will be. I have been working on a fix for this which works
for older glibcs that panic when the new relocatable VDSO is used.
However, I believe at this time that the fix is going to be too radical
to consider at this stage in the release of 2.6.21. We don't expect
this config option to be turned on by vendors for new distributions, so
at this point we are willing to drop support for it when VMI is compiled
in, and work on a patch for 2.6.22 which more fully addresses the
problem.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only System PLL clock source is selectable by CSCR_SYSTEM_SEL
bit. MPU PLL is driven by 512*CLK32 for each case.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The minimal bus clock prescaler should be kept at value
selected by the board / boot loader designer.
Switching frequency above startup limit could
lead to the external memory/devices misbehave.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code for performing the calculation was only in the SH-4 probe
path, move it out to the common path so the other parts get this
right too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When a SH7751R system includes a card that has wide range space
like a graphics card, the pci-pci bridge controller can't set the
correct address range.
For example, when *lower_limit is 0xfd000000 and bar_size is
0x4000000, in the following code at arch/sh/drivers/pci/pci-auto.c,
0x0 is set in bar_value.
pciauto_setup_bars()
{
...
bar_value = ((*lower_limit - 1) & ~(bar_size - 1)) + bar_size;
...
*lower_limit = bar_value + bar_size;
}
As a result, 0x4000000 is set in *lower_limit, but this value is wrong.
The following patch avoids this problem by checking the range of the
value and refusing to update the BAR if the calculated value ends up
being bogus.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix atomicity of TIF update in flush_thread() for sparc64
Fixes correctly the race by using *_ti_thread_flag.
Race :
parent process executing :
sys_ptrace()
(lock_kernel())
(ptrace_get_task_struct(pid))
arch_ptrace()
ptrace_detach()
ptrace_disable(child);
clear_singlestep(child);
clear_tsk_thread_flag(child, TIF_SINGLESTEP);
(which clears the TIF_SINGLESTEP flag atomically from a different
process)
(put_task_struct(child))
(unlock_kernel())
And at the same time, in the child process :
sys_execve()
do_execve()
search_binary_handler()
load_elf_binary()
flush_old_exec()
flush_thread()
doing a non-atomic thread flag update
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing checks to PS3 specific drivers ps3av and sys-manager to verify that
we are actually running on a PS3 (pointed out by Arnd).
Correct existing checks in other subsystems/drivers to return -ENODEV instead
of zero.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The SPU code doesn't properly invalidate SPUs SLBs when necessary,
for example when changing a segment size from the hugetlbfs code. In
addition, it saves and restores the SLB content on context switches
which makes it harder to properly handle those invalidations.
This patch removes the saving & restoring for now, something more
efficient might be found later on. It also adds a spu_flush_all_slbs(mm)
that can be used by the core mm code to flush the SLBs of all SPEs that
are running a given mm at the time of the flush.
In order to do that, it adds a spinlock to the list of all SPEs and move
some bits & pieces from spufs to spu_base.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Due to a buggy unsigned comparison, it was possible to write
beyond the end of the local store file in spufs under some
circumstances.
This rewrites the buggy function to look more like
simple_copy_from_buffer.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
* 'merge' of master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] 85xx: Enable CONFIG_SERIAL_8250_SHARE_IRQ
[POWERPC] Select u-image as default image for Linkstation
[POWERPC] 83xx: Minor fixes for 834x_mds USB setup code
[POWERPC] Fix warning in powermac pci.c
[POWERPC] Fix warning in powermac feature.c
[POWERPC] Fix warning in prom_parse.c of_irq_map_oldworld()
[POWERPC] Celleb: bug fix caused by not casting pointer types
[POWERPC] Add missing newline in xmon help output
[POWERPC] No DEEPNAP on 970MP 1.0
o Fix build error.
o Handle error returns.
o Deal with signals received while sleeping.
o Don't allow to be selected when we're not building the directory with
the driver anyway.
o Coding style cleanups.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
x86_64 nvidia_bugs() broke when we bailed out on not finding the HPET.
However, the quirk works by checking for _not_ finding the HPET...
Delete the nvidia_hpet_detected flag and simply test for
not finding the HPET, which is simple to do now that
acpi_table_parse returns 1 on failure.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring defconfig, tiger_defconfig and zx1_defconfig up to date. Also
sprinkle KEXEC and KDUMP combinations around liberally so that my
usual regression test builds will see all combinations:
tiger_defconfig gets KEXEC=y, CRASH_DUMP=n
zx1_defconfig gets KEXEC=n, CRASH_DUMP=y
defconfig gets KEXEC=y, CRASH_DUMP=y
others remain at KEXEC=n, CRASH_DUMP=n
Signed-off-by: Tony Luck <tomy.luck@intel.com>
kdump_find_rsvd_region() is only called by
reserve_memory() which is in __init, so it seems that
kdump_find_rsvd_region() should also be in there.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ptrace misses clearing the syscall trace flag.
The increased syscall overhead is retained after the trace is finished.
This case happens when strace is terminated by force.
Signed-off-by: Akiyama, Nobuyuki <akiyama.nobuyuk@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Grammatical fixes (s/freezed/frozen/)
Make some variables static
Change a C++ "//" comment to "/* ... */"
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Similar to memory error recovery, when a cache error is consumed
by a user process terminate the user instead of crashing the system.
Signed-off-by: Russ Anderson (rja@sgi.com)
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Jack Steiner noticed that duplicate TLB DTC entries do not cause a
linux panic. See discussion:
http://www.gelato.unsw.edu.au/archives/linux-ia64/0307/6108.html
The current TLB recovery code is recovering from the duplicate itr.d
dropins, masking the underlying problem. This change modifies
the MCA recovery code to look for the TLB check signature of the
duplicate TLB entry and panic in that case.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
In my previous x86_64 thread fix, I forgot to initialize thread.arch.fs in
arch_prctl. A process calling arch_prctl to set %fs would lose it on the
next context switch.
It also turns out that you can switch to a process which is in the process
of exiting and which has lost its mm. In this case, it's worse than
useless to try to call arch_prctl on the host process.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IA64 and ARM-OABI are currently using their own version of epoll compat_
code.
An architecture needs epoll_event translation if alignof(u64) in 32 bit
mode is different from alignof(u64) in 64 bit mode. If an architecture
needs epoll_event translation, it must define struct compat_epoll_event in
asm/compat.h and set CONFIG_HAVE_COMPAT_EPOLL_EVENT and use
compat_sys_epoll_ctl and compat_sys_epoll_wait.
All 64 bit architecture should use compat_sys_epoll_pwait.
[sfr: restructure and move to fs/compat.c, remove MIPS version
of compat_sys_epoll_pwait, use __put_user_unaligned]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also PTRACE_OLDSETOPTIONS should be accepted, as done by kernel/ptrace.c
and forced by binary compatibility. UML/32bit breaks because of this -
since it is wise enough to use PTRACE_OLDSETOPTIONS to be binary compatible
with 2.4 host kernels.
Until 2.6.17 (commit f0f2d6536e) we had:
default:
return sys_ptrace(request, pid, addr, data);
Instead here we have:
case PTRACE_GET_THREAD_AREA:
case ...:
return sys_ptrace(request, pid, addr, data);
default:
return -EINVAL;
This change was a style change - when a case is added, it must be
explicitly tested this way. In this case, not enough testing was done.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid reusing userspace errno twice - it can be cleared by libc code
everywhere (in particular printk() does clear it in my setup).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid returning ENOMEM in case of a duplicate IRQ - ENOMEM was saved into err
earlier.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix confusion about call context - comments and code are inconsistent and
plain wrong, my fault.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since both UML consoles do not use percpu variables, they may be called when
the cpu is still offline, and they may be marked CON_ANYTIME (this is
documented in kernel/printk.c, grep for CON_ANYTIME to find mentions of this).
Works well in testing done with lock debug enabled, should be safe but is not
needed for next release.
This would probably help also stderr_console.c, but this is yet to test.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
os_usr1_signal() is totally unused, os_usr1_process() is used only by TT mode.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memory allocated by mcast_user_init must be freed in the matching mcast_remove.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sharpsl_pm code depends on some symbols in the APM emulation code.
Add the dependency for now until a better solution can be found.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix tosa compile failure from commit
32f3f49910
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Product Manager of the cc9p insist on using the correct product names.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The root cause of this bug shows that this machine
could not possibly run an ACPI-aware OS without a
model specific workaround.
http://bugzilla.kernel.org/show_bug.cgi?id=5966
Signed-off-by: Len Brown <len.brown@intel.com>
Fix broken node manipulating code, and clarify inaccurate comment.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] fsys_getcpu for IA64
[IA64] remove duplicate declaration of efi_initialize_iomem_resources
[IA64] Pick highest possible saved_max_pfn for crash_dump
[IA64] fix NULL pointer in ia64/irq_chip-mask/unmask function
CC arch/mips/arc/init.o
arch/mips/arc/init.c: In function 'prom_init':
arch/mips/arc/init.c:27: warning: ISO C90 forbids mixed declarations and code
arch/mips/arc/init.c:35: warning: format ‘%08lx’ expects type ‘long unsigned int’, but argument 2 has type 'ULONG'
arch/mips/arc/init.c:28: warning: unused variable 'c'
arch/mips/arc/init.c:27: warning: unused variable ‘cnt’
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On 1.6GHz Montectio Tiger4, the following performance data is measured with
kernel built with defconfig which has NUMA configured:
Fastest sys_getcpu: 502 itc counts.
Fastest fsys_getcpu: 28 itc counts.
fsys_getcpu performance is largly impacted by whether data (node_to_cpu_map
etc) is in cache. It can take fsys_getcpu up to ~150 itc counts in cold
cache case.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
efi_initialize_iomem_resources() is declared in both include/linux/efi.h
and arch/ia64/kernel/setup.c. This patch removes the latter.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Berhhard Walle noted that on his HP rx8640 he ended up with saved_max_pfn
smaller than the highest address of system ram in /proc/iomem and proposed
a patch to base the address on the unrounded and unfiltered EFI memory
map address. Simon Horman and Magnus Damm suggested that the whole test
be moved earlier in the function. This is the combination of both of
these patches.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes boot failure because irq_desc->mask() is NULL.
- Added mask/unmask functions to ia64's irq desc function table.
- rename hw_interrupt_type to irq_chip. hw_interrupt_type is old name.
- Tony: Added same change to arch/ia64/sn/kernel/irq.c as pointed out
by Eric Biederman ... mask/unmask functions there can be no-op.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
avr32: dma-mapping.h
[AVR32] Don't use kmap() in flush_icache_page()
[AVR32] Fix bogus ti->flags manipulation in debug handler
[AVR32] Fix typo in include/asm-avr32/Kbuild
[AVR32] show_trace: Only walk valid stack addresses
[AVR32] at32_spi_setup_slaves should be __init
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Kill off I/O cruft for R7780RP.
sh: Revert lazy dcache writeback changes.
sh: Enable SM501 support for RTS7751R2D.
sh: Use L1_CACHE_BYTES for .data.cacheline_aligned.
sysctl: Support vdso_enabled sysctl on SH.
sh: Fix kernel thread stack corruption with preempt.
doc: Add SH to vdso and earlyprintk in kernel-parameters.txt
sh: Fix sigmask trampling in signal delivery.
sh: Clear UBC when not in use.
check_tsc_sync_source() depends on being called with irqs disabled (it
checks whether the TSC is coherent across two specific CPUs). This is
incidentally true during bootup, but not during cpu hotplug __cpu_up().
This got found via smp_processor_id() debugging.
disable irqs explicitly and remove the unconditional enabling of
interrupts. Add touch_nmi_watchdog() to the cpu_online_map busy loop.
this bug is present both on i386 and on x86_64.
Reported-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a warning due to unused result from pci_enable_device() in
powermac pci.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a warning due to unused return from pci_enable_device() in
powermac feature.c core99_ata100_enable() function.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This function spews a warning due to possible use of an uninitialized
variable. This can happen on broken device-trees or when called with
a NULL argument. Makes ure we properly fail instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a bug caused by changes of pointer type in
commit f1fda89522.
hose->cfg_addr type is "volatile unsigned int __iomem *", so
"hose->cfg_addr + X" will not make an intended address.
This patch also adds comments for usage of cfg_addr and cfg_data in
pci_controller structure. We use them in irregular way, and the
original code is short of explanations about them.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My patch to add spu disassembly (af89fb8041)
removed a newline from the xmon help that it shouldn't have, put it back.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
970MP rev 1.0 is reported to have nonworking DEEPNAP support, we've had
bug reports of lockups on those machines. Appearantly Apple used them
on some dual-core dual-cpu systems. Rev 1.1 is OK, and that's the one
that all 4-way systems seem to use.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
flush_icache_page() can be called from atomic context, so we can't
use kmap(). Use page_address() instead.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
We should OR in a bitmask, not a bit offset, into ti->flags. This
might fix some strange behaviour when single stepping.
Also, use set_ti_thread_flag() to manipulate the flags to avoid
surprises in the future.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Terminate the frame pointer walk if (a) the address is outside the
task's kernel stack or (b) if the frame pointer isn't monotonically
increasing. Without this fix, show_trace() may enter an infinite
loop, walking through random data anywhere in memory.
Since any address within the kernel stack is guaranteed to be valid,
we may eliminate the __get_user() calls as well.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds the delayed application attribute to the dss2 clock. DSS2
can't select the 48MHz APLL with properly with out validating the
configuration as trigged by this flag.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: OMAP: Fix missing #include <linux/workqueue.h> in
board-h2.c resulting in
In file included from arch/arm/mach-omap1/board-h2.c:40:
include/asm/arch/irda.h:27: error: field 'gpio_expa' has
incomplete type
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] cio: Call cancel_halt_clear even when actl == 0.
[S390] cio: Use path verification to check for path state.
[S390] cio: Fix locking when calling notify function.
[S390] Fixed handling of access register mode faults.
[S390] dasd: Use default recovery for SNSS requests
[S390] check_bugs() should be inline.
[S390] tape: Compression overwrites crypto setting
[S390] nss: disable kexec.
[S390] reipl: move dump_prefix_page out of text section.
[S390] smp: disable preemption in smp_call_function/smp_call_function_on
[S390] kprobes breaks BUG_ON
Use irq_handler_t for passing clock handler routine around.
And use new rtc_time in place of hwclock_time.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove regs arg from bad interrupt handler.
Use irq_handler_t type for handler arg of local request_irq().
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use irq_handler_t type for passing around timer interrupt routine
in 368360 setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use irq_handler_t type for passing around timer interrupt routine.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] kexec: Use EFI_LOADER_DATA for ELF core header
[IA64] permon use-after-free fix
[IA64] sync compat getdents
[IA64] always build arch/ia64/lib/xor.o
[IA64] Remove stack hard limit on ia64
[IA64] point saved_max_pfn to the max_pfn of the entire system
Revert "[IA64] swiotlb abstraction (e.g. for Xen)"
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
sis900 warning fixes
mv643xx_eth: Place explicit port number in mv643xx_eth_platform_data
pcnet32: Fix PCnet32 performance bug on non-coherent architecutres
__devinit & __devexit cleanups for de2104x driver
3c59x: Handle pci_enable_device() failure while resuming
dmfe: Fix link detection
dmfe: fix two bugs
dmfe: trivial/spelling fixes
revert "drivers/net/tulip/dmfe: support basic carrier detection"
ucc_geth: returns NETDEV_TX_BUSY when BD ring is full
ucc_geth: Fix BD processing
natsemi: netpoll fixes
bonding: Improve IGMP join processing
bonding: only receive ARPs for us
bonding: fix double dev_add_pack
Apply commit 0550d9d13e to c-tx39.c too.
And fix a warning in local_tx39_flush_data_cache_page().
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The address where the ELF core header is stored is passed to the secondary
kernel as a kernel command line option. The memory area for this header is
also marked as a separate EFI memory descriptor on ia64.
The separate EFI memory descriptor is at the moment of the type
EFI_UNUSABLE_MEMORY. With such a type the secondary kernel skips over the
entire memory granule (config option, 16M or 64M) when detecting memory.
If we are lucky we will just lose some memory, but if we happen to have
data in the same granule (such as an initramfs image), then this data will
never get mapped and the kernel bombs out when trying to access it.
So this is an attempt to fix this by changing the EFI memory descriptor
type into EFI_LOADER_DATA. This type is the same type used for the kernel
data and for initramfs. In the secondary kernel we then handle the ELF
core header data the same way as we handle the initramfs image.
This patch contains the kernel changes to make this happen. Pretty
straightforward, we reserve the area in reserve_memory(). The address for
the area comes from the kernel command line and the size comes from the
specialized EFI parsing function vmcore_find_descriptor_size().
The kexec-tools-testing code for this can be found here:
http://lists.osdl.org/pipermail/fastboot/2007-February/005983.html
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Cc: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Perfmon associates vmalloc()ed memory with a file descriptor, and installs
a vma mapping that memory. Unfortunately, the vm_file field is not filled
in, so processes with mappings to that memory do not prevent the file from
being closed and the memory freed. This results in use-after-free bugs and
multiple freeing of pages, etc.
I saw this bug on an Altix on SLES9. Haven't reproduced upstream but it
looks like the same issue is there.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add VERIFY_WRITE check in the beginning like compat_sys_getdents() (EINVAL vs
EFAULT).
Signed-off-by: Alexandr Andreev <aandreev@openvz.org>
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Always build ia64 xor.o because multiple config options now depend on it.
Necessary to build .20-mm* on ia64 when, e.g., CONFIG_ASYNC_TX_DMA is
defined. Don't know if '_ASYNC_TX_DMA makes sense on ia64. If not, maybe
Kconfig should preclude it.
Could have defined a Kconfig option that defaults to true if MD_RAID456 ||
ASYNC_TX_DMA to control building of xor.o, but xor.o is only 848 bytes and
this IS ia64...
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make saved_max_pfn point to max_pfn of entire system.
Without this patch is so that vmcore is zero length on ia64. This is
because saved_max_pfn was wrongly being set to the max_pfn of the crash
kernel's address space, rather than the max_pfg on the physical memory of
the machine - the whole purpose of vmcore is to access physical memory that
is not part of the crash kernel's addresss space.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Sort-Of-Acked-By: Jay Lan <jlan@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Comment the fact that sig_info is initialized early in boot, and thus doesn't
need any locking.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a debugging message in the case that mapping a stub fails.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a few formatting bugs in the signal code.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal. Fixup the remaining users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were using the platform_device.id field to identify which ethernet
port is used for mv643xx_eth device. This is not generally correct.
It will be incorrect, for example, if a hardware platform uses a single
port but not the first port. Here, we add an explicit port_number field
to struct mv643xx_eth_platform_data.
This makes the mv643xx_eth_platform_data structure required, but that
isn't an issue since all users currently provide it already.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replaced check_user_space() + __check_access_register with the new
check_space(). The old functions made wrong assumptions about kernel
and user space when the kernel and user address spaces are switched
(kernel in home space, user in primary/secondary space).
Secondly the user process can switch to the accress register mode if
it is running in primary or secondary mode. In addition it can load
an arbitrary value to the access registers. If any other value than
0 for primary space or 1 for secondary space is loaded and memory
is accessed using the base register related to the access register,
the program should be terminated with a SIGSEGV. To achieve that the
DUALD pointer in the DUCT and the PSALD pointer in the PASTE need
to point to an array of 8 invalid access-list entries to get a
ALEN-translation exception if an invalid alet is used.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
nss and kexec don't work together since kexec wants to write to the
read-only text section of the shared kernel image.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reipl doesn't work on older machines were s390_reset_machine() gets
called. The reason is that the text section is read-only but the
variable dump_prefix_page is there. Since s390_reset_machine() writes
to it we get a protection exception.
Therefore move dump_prefix_page to the bss section.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Avoid sprinkling a _lot_ of preempt_disable/preempt_enable pairs.
This would be necessary for e.g. the iucv driver. Also this way we
are more consistent with other architectures which disable
preemption at least for smp_call_function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The illegal operation handler calls the die notifier with DIE_BPT to
let kprobes pick up its breakpoint. If kprobes does not find its
breakpoint it returns NOTIFY_STOP instead of NOTIFY_DONE.
Since we use stop_machine_run on s390 to arm/disarm the kprobes
breakpoints the race that kprobe_handler tries to solve by checking
for the kprobes breakpoints does not exist. Removing the check makes
BUG_ON working again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CONFIG_PARAVIRT broke old glibc bootup: it silently turned off the
selectability of CONFIG_COMPAT_VDSO and thus rendered distro kernels
unbootable on old-style VDSO glibc setups.
the proper solution is to keep COMPAT_VDSO available - if a hypervisor
needs any modification of that concept then we'll judge those changes in
full context, once those changes are submitted.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do not use default=y for CONFIG_VMI (we do not do that for any driver or
special-hardware feature): the overwhelming majority of Linux users does
not need it, and interested users and distributions can enable it
as-needed.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clarify the description of the CONFIG_VMI option: describe the reality
that VMI is a VMWare-only interface for now. Once that changes and
another hypervisor adopts the VMI ABI we can change the text.
As can be seen from the Xen paravirtualization patches submitted to lkml
the Xen project has chosen its own, non-VMI interface between Xen and
the para-Linux - so remove Xen from the description.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Temove the mistaken turning on of NO_IDLE_HZ on x86+PARAVIRT kernels.
It's an obsolete, limited form of dynticks.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CC arch/i386/kernel/vmi.o
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c: In function 'vmi_map_pt_hook':
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: 'KM_PTE0' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: 'KM_PTE1' undeclared (first use in this function)
make[2]: *** [arch/i386/kernel/vmi.o] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resolves the issue found here:
http://bugme.osdl.org/show_bug.cgi?id=7426
The basic summary is:
Currently we register most of i386/x86_64 clocksources at module_init
time. Then we enable clocksource selection at late_initcall time. This
causes some problems for drivers that use gettimeofday for init
calibration routines (specifically the es1968 driver in this case),
where durring module_init, the only clocksource available is the low-res
jiffies clocksource. This may cause slight calibration errors, due to
the small sampling time used.
It should be noted that drivers that require fine grained time may not
function on architectures that do not have better then jiffies
resolution timekeeping (there are a few). However, this does not
discount the reasonable need for such fine-grained timekeeping at init
time.
Thus the solution here is to register clocksources earlier (ideally when
the hardware is being initialized), and then we enable clocksource
selection at fs_initcall (before device_initcall).
This patch should probably get some testing time in -mm, since
clocksource selection is one of the most important issues for correct
timekeeping, and I've only been able to test this on a few of my own
boxes.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Testing NMI watchdog ... CPU#0: NMI appears to be stuck (54->54)!
CPU#1: NMI appears to be stuck (0->0)!
Keep the PIT/HPET alive when nmi_watchdog = 1 is given on the command
line.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Critical fixes for SMP.
Fix a couple functions which needed to be __devinit and fix a bogus parameter
to AP startup that just so happened to work because the low virtual mapping of
memory was still established.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use para_fill instead of directly setting the APIC ops to the result of the
vmi_get_function call - this allows one to implement a VMI ROM without
implementing APIC functions, just using the native APIC functions.
While doing this, I realized that there is a lot more cleanup that should have
been done. Basically, we should never assume that the ROM implements a
specific set of functions, and always allow fallback to the native
implementation.
This is critical for future compatibility.
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More goo from hrtimers integration. We do compile and run properly with NO_HZ
enabled. There was a period when we didn't because of a missing export, but
that was since fixed.
And with the clocksource code now firmly in place, we can get rid of code that
fixes up the wallclock, since this is done in the common infrastructure. This
actually fixes a timer bug as well, that was caused by do_settimeofday no
longer being callable with interrupts disabled due to the use of
on_each_cpu().
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The time_init_hook in paravirt-ops no longer functions in the correct manner
after the integration of the hrtimers code. The problem is that now the call
path for time initialization is:
time_init :
late_time_init = hpet_time_init;
late_time_init -> hpet_time_init:
setup_pit_timer (BAD)
do_time_init --> (via paravirt.h)
time_init_hook --> (via arch_hooks.h)
time_init_hook (in SUBARCH/setup.c)
If this isn't confusing enough, the paravirt case goes through an indirect
function pointer in the paravirt-ops table. The problem is, by the time the
paravirt hook is called, the pit timer is already enabled.
But paravirt guests have their own timer, and don't want to use the PIT.
Rather than intensify the struggle for power going on here, just make it all
nice and simple and just unconditionally do all timer setup in the
late_time_init hook. This also has the advantage of enabling timers in the
same place in all code paths, so everyone has the same bugs and we don't have
outliers who break other code because they turn on timer too early or too
late.
So the paravirt-ops time init function is now by default hpet_time_init, which
is the time init function used for native hardware. Paravirt guests have the
chance to override this when they setup the paravirt-ops table, and should
need no change.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
