* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
percpu: unbreak alpha percpu
mutex: have non-spinning mutexes on s390 by default
Since the first argument to I2C_BOARD_INFO() must be a string constant,
there is no need to parenthesise it, and adding parentheses results in
an invalid initialiser for char[]. gcc obviously accepts this syntax as
an extension, but sparse complains, e.g.:
drivers/net/sfc/boards.c:173:2: warning: array initialized from parenthesized string constant
Therefore, remove the parentheses.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Impact: provide useful missing info for developers
Kernel taint can occur in several situations such as warnings,
load of prorietary or staging modules, bad page, etc...
But when such taint happens, a developer might still be working on
the kernel, expecting that lockdep is still enabled. But a taint
disables lockdep without ever warning about it.
Such a kernel behaviour doesn't really help for kernel development.
This patch adds this missing warning.
Since the taint is done most of the time after the main message that
explain the real source issue, it seems safe to warn about it inside
add_taint() so that it appears at last, without hurting the main
information.
v2: Use a generic helper to disable lockdep instead of an
open coded xchg().
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <1239412638-6739-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Noises can be introduced when LCD signals are being driven, some platforms
provide a signal to assist the synchronization of this sampling procedure.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For the time being, move the generic percpu_*() accessors to
linux/percpu.h.
asm-generic/percpu.h is meant to carry generic stuff for low level
stuff - declarations, definitions and pointer offset calculation
and so on but not for generic interface.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
Separate out the proc- and unit-specific header directories from the general
Move arch headers from include/asm-mn10300/ to arch/mn10300/include/asm/.
For example:
__stringify(__entry->irq, __entry->ret)
will now convert it to:
"REC->irq, REC->ret"
It also still supports single arguments as the old macro did.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <49DC6751.30308@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some drivers like Intel8x0 or Intel HDA are broken for some hardware variants.
This patch adds more strict buffer position checks based on jiffies when
internal hw_ptr is updated. Enable xrun_debug to see mangling of wrong
positions.
As a side effect, the hw_ptr interrupt update routine might do slightly better
job when many interrupts are lost.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (27 commits)
xsysace: Fix dereferencing of cf_id after hd_driveid removal
at91_ide: turn on PIO 6 support
at91_ide: remove unused ide_mm_{outb,inb}
ide-cd: reverse NOT_READY sense key logic
ide: refactor tf_read() method
ide: refactor tf_load() method
ide: call write_devctl() method from tf_read() method
ide: move common code out of tf_load() method
ide: simplify 'struct ide_taskfile'
ide: replace IDE_TFLAG_* flags by IDE_VALID_*
ide-cd: fix intendation in cdrom_decode_status()
ide-cd: unify handling of fs and pc requests in cdrom_decode_status()
ide-cd: convert cdrom_decode_status() to use switch statements
ide-cd: update debugging support
ide-cd: respect REQ_QUIET for fs requests in cdrom_decode_status()
ide: remove unused #include <linux/version.h>
tx4939ide: Fix tx4939ide_{in,out}put_data_swap argument
tx493[89]ide: Remove big endian version of tx493[89]ide_tf_{load,read}
ide-cd: carve out an ide_cd_breathe()-helper for fs write requests
ide-cd: move status checking into the IRQ handler
...
asm-frv/pgtable.h could just #include <asm-generic/pgtable.h> in NOMMU mode
rather than #defining macros for lazy MMU and CPU stuff.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: consolidate documents
blktrace: pass the right pointer to kfree()
tracing/syscalls: use a dedicated file header
tracing: append a comma to INIT_FTRACE_GRAPH
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: do not count frozen tasks toward load
sched: refresh MAINTAINERS entry
sched: Print sched_group::__cpu_power in sched_domain_debug
cpuacct: add per-cgroup utime/stime statistics
posixtimers, sched: Fix posix clock monotonicity
sched_rt: don't allocate cpumask in fastpath
cpuacct: make cpuacct hierarchy walk in cpuacct_charge() safe when rcupreempt is used -v2
Since the whole point of try_then_request_module is to retry
the operation after a module has been loaded, we must wait for
the module to fully load.
Otherwise all sort of things start breaking, e.g., you won't
be able to read your encrypted disks on the first attempt.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Tested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Freezing tasks via the cgroup freezer causes the load average to climb
because the freezer's current implementation puts frozen tasks in
uninterruptible sleep (D state).
Some applications which perform job-scheduling functions consult the
load average when making decisions. If a cgroup is frozen, the load
average does not provide a useful measure of the system's utilization
to such applications. This is especially inconvenient if the job
scheduler employs the cgroup freezer as a mechanism for preempting low
priority jobs. Contrast this with using SIGSTOP for the same purpose:
the stopped tasks do not count toward system load.
Change task_contributes_to_load() to return false if the task is
frozen. This results in /proc/loadavg behavior that better meets
users' expectations.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Tested-by: Nigel Cunningham <nigel@tuxonice.net>
Cc: <stable@kernel.org>
Cc: containers@lists.linux-foundation.org
Cc: linux-pm@lists.linux-foundation.org
Cc: Matt Helsley <matthltc@us.ibm.com>
LKML-Reference: <20090408194512.47a99b95@manatee.lan>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix build warnings and possibe compat misbehavior on IA64
Building a kernel on ia64 might trigger these ugly build warnings:
CC arch/ia64/ia32/sys_ia32.o
In file included from arch/ia64/ia32/sys_ia32.c:55:
arch/ia64/ia32/ia32priv.h:290:1: warning: "elf_check_arch" redefined
In file included from include/linux/elf.h:7,
from include/linux/module.h:14,
from include/linux/ftrace.h:8,
from include/linux/syscalls.h:68,
from arch/ia64/ia32/sys_ia32.c:18:
arch/ia64/include/asm/elf.h:19:1: warning: this is the location of the previous definition
[...]
sys_ia32.c includes linux/syscalls.h which in turn includes linux/ftrace.h
to import the syscalls tracing prototypes.
But including ftrace.h can pull too much things for a low level file,
especially on ia64 where the ia32 private headers conflict with higher
level headers.
Now we isolate the syscall tracing headers in their own lightweight file.
Reported-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jason Baron <jbaron@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Michael Rubin <mrubin@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Michael Davidson <md@google.com>
LKML-Reference: <20090408184058.GB6017@nowhere>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
igb: remove sysfs entry that was used to set the number of vfs
igbvf: add new driver to support 82576 virtual functions
drivers/net/eql.c: Fix a dev leakage.
niu: Fix unused variable warning.
r6040: set MODULE_VERSION
bnx2: Don't use reserved names
FEC driver: add missing #endif
niu: Fix error handling
mv643xx_eth: don't reset the rx coal timer on interface up
smsc911x: correct debugging message on mii read timeout
ethoc: fix library build errors
netfilter: ctnetlink: fix regression in expectation handling
netfilter: fix selection of "LED" target in netfilter
netfilter: ip6tables regression fix
Prepare for full barrier implementation: first remove the restricted support.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
x86 ACPI: Add support for Always Running APIC timer
ACPI x86: Make aperf/mperf MSR access in acpi_cpufreq read_only
ACPI x86: Cleanup acpi_cpufreq structures related to aperf/mperf
ACPICA: delete check for AML access to port 0x81-83
ACPI: WMI: use .notify method instead of installing handler directly
sony-laptop: use .notify method instead of installing handler directly
panasonic-laptop: use .notify method instead of installing handler directly
fujitsu-laptop: use .notify method instead of installing hotkey handler directly
fujitsu-laptop: use .notify method instead of installing handler directly
ACPI: video: use .notify method instead of installing handler directly
ACPI: thermal: use .notify method instead of installing handler directly
ACPI battery: fix async boot oops
ACPI: delete acpi_device.g_list
NULL noise: drivers/platform/x86/panasonic-laptop.c
ACPI: cpufreq: remove dupilcated #include
ACPI: Adjust Kelvin offset to match local implementation
ACPI: convert acpi_device_lock spinlock to mutex
Thou shalt remember to use 'git add' or errors shall be visited on your
downloads and there shall be wrath from on list and much gnashing of teeth.
Thou shalt remember to use git status or there shall be catcalls and much
embarrasment shall come to pass.
Signed-off-by: Alan "I'm hiding" Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Save the bit 17 state of the pages when freeing the page list, and
reswizzle them if necessary when rebinding the pages (in case they were
swapped out). Since we have userland with expectations that the swizzle
enums let it pread and pwrite contents accurately, we can't expose a new
swizzle enum for bit 17 (which it would have to GTT map to handle), so we
handle it down in pread and pwrite by swizzling the copy when bit 17 of the
page address is set.
Signed-off-by: Eric Anholt <eric@anholt.net>
Simplify tf_read() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and factoring out the code that
deals with the high order bytes into ide_tf_readback() to be called from the
only two functions interested, ide_complete_cmd() and ide_dump_sector().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for
the method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_load() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and moving the code that deals
with the high order bytes into the only function interested, do_rw_taskfile().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for the
method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make 'struct ide_taskfile' cover only 8 register values and thus put two such
fields ('tf' and 'hob') into 'struct ide_cmd', dropping unnecessary 'tf_array'
field from it.
This required changing the prototype of ide_get_lba_addr() and ide_tf_dump().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: fix setting of ATA_LBA bit for LBA48 commands in __ide_do_rw_disk()]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace IDE_TFLAG_{IN|OUT}_* flags meaning to the taskfile register validity on
input/output by the IDE_VALID_* flags and introduce 4 symmetric 8-bit register
validity indicator subfields, 'valid.{input/output}.{tf|hob}', into the 'struct
ide_cmd' instead of using the 'tf_flags' field for that purpose (this field can
then be turned from 32-bit into 8-bit one).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: dont break future extensions of INIT_TASK
While not a problem right now, due to lack of a comma, build fails if
elements are appended to INIT_TASK() macro in development code:
arch/x86/kernel/init_task.c:33: error: request for member `XXXXXXXXXX' in something not a structure or union
arch/x86/kernel/init_task.c:33: error: initializer element is not constant
arch/x86/kernel/init_task.c:33: error: (near initialization for `init_task.ret_stack')
make[1]: *** [arch/x86/kernel/init_task.o] Error 1
make: *** [arch/x86/kernel] Error 2
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: srostedt@redhat.com
LKML-Reference: <200904080505.n3855hcn017109@www262.sakura.ne.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch documents the new bindings for the MPC I2C bus driver.
Furthermore, it removes obsolete FSL device related definitions
for I2C.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'core/softlockup' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softlockup: make DETECT_HUNG_TASK default depend on DETECT_SOFTLOCKUP
softlockup: move 'one' to the softlockup section in sysctl.c
softlockup: ensure the task has been switched out once
softlockup: remove timestamp checking from hung_task
softlockup: convert read_lock in hung_task to rcu_read_lock
softlockup: check all tasks in hung_task
softlockup: remove unused definition for spawn_softlockup_task
softlockup: fix potential race in hung_task when resetting timeout
softlockup: fix to allow compiling with !DETECT_HUNG_TASK
softlockup: decouple hung tasks check from softlockup detection
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y
branch tracer: Fix for enabling branch profiling makes sparse unusable
ftrace: Correct a text align for event format output
Update /debug/tracing/README
tracing/ftrace: alloc the started cpumask for the trace file
tracing, x86: remove duplicated #include
ftrace: Add check of sched_stopped for probe_sched_wakeup
function-graph: add proper initialization for init task
tracing/ftrace: fix missing include string.h
tracing: fix incorrect return type of ns2usecs()
tracing: remove CALLER_ADDR2 from wakeup tracer
blktrace: fix pdu_len when tracing packet command requests
blktrace: small cleanup in blk_msg_write()
blktrace: NUL-terminate user space messages
tracing: move scripts/trace/power.pl to scripts/tracing/power.pl
* 'irq/threaded' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: fix devres.o build for GENERIC_HARDIRQS=n
genirq: provide old request_irq() for CONFIG_GENERIC_HARDIRQ=n
genirq: threaded irq handlers review fixups
genirq: add support for threaded interrupts to devres
genirq: add threaded interrupt handler support
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: pci_slot: grab refcount on slot's bus
PCI Hotplug: acpiphp: grab refcount on p2p subordinate bus
PCI: allow PCI core hotplug to remove PCI root bus
PCI: Fix oops in pci_vpd_truncate
PCI: don't corrupt enable_cnt when doing manual resource alignment
PCI: annotate pci_rescan_bus as __ref, not __devinit
PCI-IOV: fix missing kernel-doc
PCI: Setup disabled bridges even if buses are added
PCI: SR-IOV quirk for Intel 82576 NIC
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
loop: mutex already unlocked in loop_clr_fd()
cfq-iosched: don't let idling interfere with plugging
block: remove unused REQ_UNPLUG
cfq-iosched: kill two unused cfqq flags
cfq-iosched: change dispatch logic to deal with single requests at the time
mflash: initial support
cciss: change to discover first memory BAR
cciss: kernel scan thread for MSA2012
cciss: fix residual count for block pc requests
block: fix inconsistency in I/O stat accounting code
block: elevator quiescing helpers
The code that enables branch tracing for all (non-constant) branches
plays games with the preprocessor and #define's the C 'if ()' construct
to do tracing.
That's all fine, but it fails for some unusual but valid C code that is
sometimes used in macros, notably by the intel-iommu code:
if (i=drhd->iommu, drhd->ignored) ..
because now the preprocessor complains about multiple arguments to the
'if' macro.
So make the macro expansion of this particularly horrid trick use
varargs, and handle the case of comma-expressions in if-statements. Use
another macro to do it cleanly in just one place.
This replaces a patch by David (and acked by Steven) that did this all
inside that one already-too-horrid macro.
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-2630-v2' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c: imx: Make disable_delay a per-device variable
i2c: xtensa s6000 i2c driver
powerpc/85xx: i2c-mpc: use new I2C bindings for the Socates board
i2c: i2c-mpc: make I2C bus speed configurable
i2c: i2c-mpc: use dev based printout function
i2c: i2c-mpc: various coding style fixes
i2c: imx: Add missing request_mem_region in probe()
i2c: i2c-s3c2410: Initialise Samsung I2C controller early
i2c-s3c2410: Simplify bus frequency calculation
i2c-s3c2410: sda_delay should be in ns, not clock ticks
i2c: iMX/MXC support
PCI parallel port devices can IRQ share so we should stop them hogging
the line and making a mess on modern PC systems. We know the sharing
side works as the PCMCIA driver has shared the parallel port IRQ for
some time.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(akpm: queued pending confirmation of the new major number)
[randy.dunlap@oracle.com: select SERIAL_CORE]
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tty_driver_kref_get() should be static inline and not extern inline
(the latter even changed it's semantics in gcc >= 4.3).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After a review of user's feedback for finding out other compatibility
issues, I found nilfs improperly initializes timestamps in inode;
CURRENT_TIME was used there instead of CURRENT_TIME_SEC even though nilfs
didn't have nanosecond timestamps on disk. A few users gave us the report
that the tar program sometimes failed to expand symbolic links on nilfs,
and it turned out to be the cause.
Instead of applying the above displacement, I've decided to support
nanosecond timestamps on this occation. Fortunetaly, a needless 64-bit
field was in the nilfs_inode struct, and I found it's available for this
purpose without impact for the users.
So, this will do the enhancement and resolve the tar problem.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The former versions didn't have extra super blocks. This improves the
weak point by introducing another super block at unused region in tail of
the partition.
This doesn't break disk format compatibility; older versions just ingore
the secondary super block, and new versions just recover it if it doesn't
exist. The partition created by an old mkfs may not have unused region,
but in that case, the secondary super block will not be added.
This doesn't make more redundant copies of the super block; it is a future
work.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nilfs creates checkpoints even for garbage collection or metadata updates
such as checkpoint mode change. So, user often sees checkpoints created
only by such internal operations.
This is inconvenient in some situations. For example, application that
monitors checkpoints and changes them to snapshots, will fall into an
infinite loop because it cannot distinguish internally created
checkpoints.
This patch solves this sort of problem by adding a flag to checkpoint for
identification.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sketch file is a file to mark checkpoints with user data. It was
experimentally introduced in the original implementation, and now
obsolete. The file was handled differently with regular files; the file
size got truncated when a checkpoint was created.
This stops the special treatment and will treat it as a regular file.
Most users are not affected because mkfs.nilfs2 no longer makes this file.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a new argument to the nilfs_sustat structure.
The extended field allows to delete volatile active state of segments,
which was needed to protect freshly-created segments from garbage
collection but has confused code dealing with segments. This
extension alleviates the mess and gives room for further
simplifications.
The volatile active flag is not persistent, so it's eliminable on this
occasion without affecting compatibility other than the ioctl change.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This removes compat code from the nilfs ioctls and applies the same
function for both .ioctl and .compat_ioctl file operations.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nilfs ioctl had structures not having fixed sized types such as:
struct nilfs_argv {
void *v_base;
size_t v_nmembs;
size_t v_size;
int v_index;
int v_flags;
};
Further, some of them are wrongly aligned:
e.g.
struct nilfs_cpmode {
__u64 cm_cno;
int cm_mode;
};
The size of wrongly aligned structures varies depending on
architectures, and it breaks the identity of ioctl commands, which
leads to arch dependent errors.
Previously, these are compensated by using compat_ioctl.
This fixes these problems and allows removal of compat ioctl.
Since this will change sizes of those structures, binary compatibility
for the past utilities will once break; new utilities have to be used
instead. However, it would be helpful to avoid platform dependent
problems in the long term.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This removes NILFS_IOCTL_TIMEDWAIT command from ioctl interface along
with the related flags and wait queue.
The command is terrible because it just sleeps in the ioctl. I prefer
to avoid this by devising means of event polling in userland program.
By reconsidering the userland GC daemon, I found this is possible
without changing behaviour of the daemon and sacrificing efficiency.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a header file which specifies the on-disk format and ioctl
interface of the nilfs2 file system.
Signed-off-by: Koji Sato <sato.koji@lab.ntt.co.jp>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Largely inspired from ipc/ipc_sysctl.c. This patch isolates the mqueue
sysctl stuff in its own file.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Nadia Derbey <Nadia.Derbey@bull.net>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement multiple mounts of the mqueue file system, and link it to usage
of CLONE_NEWIPC.
Each ipc ns has a corresponding mqueuefs superblock. When a user does
clone(CLONE_NEWIPC) or unshare(CLONE_NEWIPC), the unshare will cause an
internal mount of a new mqueuefs sb linked to the new ipc ns.
When a user does 'mount -t mqueue mqueue /dev/mqueue', he mounts the
mqueuefs superblock.
Posix message queues can be worked with both through the mq_* system calls
(see mq_overview(7)), and through the VFS through the mqueue mount. Any
usage of mq_open() and friends will work with the acting task's ipc
namespace. Any actions through the VFS will work with the mqueuefs in
which the file was created. So if a user doesn't remount mqueuefs after
unshare(CLONE_NEWIPC), mq_open("/ab") will not be reflected in "ls
/dev/mqueue".
If task a mounts mqueue for ipc_ns:1, then clones task b with a new ipcns,
ipcns:2, and then task a is the last task in ipc_ns:1 to exit, then (1)
ipc_ns:1 will be freed, (2) it's superblock will live on until task b
umounts the corresponding mqueuefs, and vfs actions will continue to
succeed, but (3) sb->s_fs_info will be NULL for the sb corresponding to
the deceased ipc_ns:1.
To make this happen, we must protect the ipc reference count when
a) a task exits and drops its ipcns->count, since it might be dropping
it to 0 and freeing the ipcns
b) a task accesses the ipcns through its mqueuefs interface, since it
bumps the ipcns refcount and might race with the last task in the ipcns
exiting.
So the kref is changed to an atomic_t so we can use
atomic_dec_and_lock(&ns->count,mq_lock), and every access to the ipcns
through ns = mqueuefs_sb->s_fs_info is protected by the same lock.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move mqueue vfsmount plus a few tunables into the ipc_namespace struct.
The CONFIG_IPC_NS boolean and the ipc_namespace struct will serve both the
posix message queue namespaces and the SYSV ipc namespaces.
The sysctl code will be fixed separately in patch 3. After just this
patch, making a change to posix mqueue tunables always changes the values
in the initial ipc namespace.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mqueuefs filesystem will use this helper as well. Proc's main get_sb
could also be made to use it, but that will require a bit more rework.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The I2C functionality provided by the i2c-voodoo3 driver is moved into the
tdfxfb (frame buffer driver for Voodoo3 cards). This way there is no
conflict between the i2c driver and the fb driver.
The tdfxfb does not make use from the DDC functionality yet but provides
all the functionality of the i2c-voodoo3 driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add disable/enable_kretprobe() and disable/enable_jprobe().
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add disable_kprobe() and enable_kprobe() to disable/enable kprobes
temporarily.
disable_kprobe() asynchronously disables probe handlers of specified
kprobe. So, after calling it, some handlers can be called at a while.
enable_kprobe() enables specified kprobe.
aggr_pre_handler and aggr_post_handler check disabled probes. On the
other hand aggr_break_handler and aggr_fault_handler don't check it
because these handlers will be called while executing pre or post handlers
and usually those help error handling.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix comment style in kprobes.h.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SPI controllers have restrictions on DMAable buffers alignemt.
Currently if the buffer supplied by protocol driver is not properly
aligned, the controller silently performs transfer in PIO mode. Addition
of dma_alignment field to spi_master allows protocol drivers to perform
proper alignment.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add /proc entries to give the admin the ability to control the minimum and
maximum number of pdflush threads. This allows finer control of pdflush
on both large and small machines.
The rationale is simply one size does not fit all. Admins on large and/or
small systems may want to tune the min/max pdflush thread count to best
suit their needs. Right now the min/max is hardcoded to 2/8. While
probably a fair estimate for smaller machines, large machines with large
numbers of CPUs and large numbers of filesystems/block devices may benefit
from larger numbers of threads working on different block devices.
Even if the background flushing algorithm is radically changed, it is
still likely that multiple threads will be involved and admins would still
desire finer control on the min/max other than to have to recompile the
kernel.
The patch adds '/proc/sys/vm/nr_pdflush_threads_min' and
'/proc/sys/vm/nr_pdflush_threads_max' with r/w permissions.
The minimum value for nr_pdflush_threads_min is 1 and the maximum value is
the current value of nr_pdflush_threads_max. This minimum is required
since additional thread creation is performed in a pdflush thread itself.
The minimum value for nr_pdflush_threads_max is the current value of
nr_pdflush_threads_min and the maximum value can be 1000.
Documentation/sysctl/vm.txt is also updated.
[akpm@linux-foundation.org: fix comment, fix whitespace, use __read_mostly]
Signed-off-by: Peter W Morreale <pmorreale@novell.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the changes between kernels 2.6.28 and 2.6.29 is that a branch profiler
has been added for if() statements. Unfortunately this patch makes the sparse
output unusable with CONFIG_TRACE_BRANCH_PROFILING=y: when branch profiling is
enabled, sparse prints so much false positives that the real issues are no
longer visible. This behavior can be reproduced as follows:
* enable CONFIG_TRACE_BRANCH_PROFILING, e.g. by running make allyesconfig or
make allmodconfig.
* run make C=2
Result: a huge number of the following sparse warnings.
...
include/linux/cpumask.h:547:2: warning: symbol '______r' shadows an earlier one
include/linux/cpumask.h:547:2: originally declared here
...
The patch below fixes this by disabling branch profiling while analyzing the
kernel code with sparse.
See also:
* http://lkml.org/lkml/2008/11/21/18
* http://bugzilla.kernel.org/show_bug.cgi?id=12925
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Steven Rostedt <srostedt@redhat.com>
LKML-Reference: <200904051620.02311.bart.vanassche@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
powerpc: Fix oops when loading modules
powerpc: Wire up preadv and pwritev
powerpc/ftrace: Fix printf format warning
powerpc/ftrace: Fix #if that should be #ifdef
powerpc: Fix ptrace compat wrapper for FPU register access
powerpc: Print information about mapping hw irqs to virtual irqs
powerpc: Correct dependency of KEXEC
powerpc: Disable VSX or current process in giveup_fpu/altivec
powerpc/pseries: Enable relay in pseries_defconfig
powerpc/pseries: Fix ibm,client-architecture comment
powerpc/pseries: Scan for all events in rtasd
powerpc/pseries: Add dispatch dispersion statistics
powerpc: Clean up some prom printouts
powerpc: Print progress of ibm,client-architecture method
powerpc: Remove duplicated #include's
powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
fsl-diu-fb: Pass the proper device for dma mapping routines
powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
...
Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.
There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).
Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Impact: fix to crash going to kexec
The init task did not properly initialize the function graph pointers.
Altough these pointers are NULL, they can not be assumed to be NULL
for the init task, and must still be properly initialize.
This usually is not an issue since a problem only arises when a task
exits, and the init tasks do not usually exit. But when doing tests
with kexec, the init tasks do exit, and the bug appears.
This patch properly initializes the init tasks function graph data
structures.
Reported-and-Tested-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <alpine.DEB.2.00.0903252053080.5675@gandalf.stny.rr.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Support for the s6000 on-chip i2c controller.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The request inherits the unplug flag from the bio, but it isn't actually
used. The bio flag stops at __make_request(), which tells it to unplug
after submission. Passing it on to the request doesn't make any sense.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This driver supports mflash IO mode for linux.
Mflash is embedded flash drive and mainly targeted mobile and consumer
electronic devices.
Internally, mflash has nand flash and other hardware logics and supports 2
different operation (ATA, IO) modes. ATA mode doesn't need any new driver
and currently works well under standard IDE subsystem. Actually it's one
chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
IDE interface.
Followings are brief descriptions about IO mode.
A. IO mode based on ATA protocol and uses some custom command. (read confirm,
write confirm)
B. IO mode uses SRAM bus interface.
C. IO mode supports 4kB boot area, so host can boot from mflash.
This driver is quitely similar to a standard ATA driver, but because of
following reasons it is currently seperated with ATA layer.
1. ATA layer deals standard ATA protocol. ATA layer have many low-
level device specific interface, but data transfer keeps ATA rule.
But, mflash IO mode doesn't.
2. Even though currently not used in mflash driver code, mflash has
some custom command and modes. (nand fusing, firmware patch, etc) If
this feature supported in linux kernel, ATA layer more altered.
3. Currently PATA platform device driver doesn't support interrupt.
(I'm not sure) But, mflash uses interrupt (polling mode is just for
debug).
4. mflash is somewhat under-develop product. Even though some company
already using mflash their own product, I think more time is needed for
standardization of custom command and mode. That time (maybe October)
I will talk to with ATA people. If they accept integration, I will
integrate.
Signed-off-by: unsik Kim <donari75@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This forces in_flight to be zero when turning off or on the I/O stat
accounting and stops updating I/O stats in attempt_merge() when
accounting is turned off.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add support to the SQ-905 driver to pass back to user space the
sensor orientation information obtained from the camera during init.
Modifies gspca and the videodev2.h header to create the necessary
API.
[mchehab@redhat.com: Changed "Output is" to "Frames are" at the comments, as suggested at LMML]
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove support for the debug call VIDIOC_INT_S_AUDIO_ROUTING from cx18
and ivtv. These internal ioctls shouldn't be exposed. These were only
used through the cx18-ctl and ivtv-ctl utilities, and only when testing
a new card variant.
This cleanup allows the removal of this ioctl from v4l2-common.h.
Cc: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is no longer needed to use a struct pointer as argument, since v4l2_subdev
doesn't require that ioctl-like approach anymore. Instead just pass the input,
output and config (new!) arguments directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With all the v4l2_subdev changes that were made to these drivers it is a
good idea to increase the version number of each driver.
It's just the patch level that is increased, except for the zoran and saa7146
drivers where the minor number was increased due to the more substantial
changes that were made to those two drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than duplicating this list everywhere, just put it in tvaudio.h.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions v4l2_i2c_new_subdev and v4l2_i2c_new_probed_subdev relied on
i2c_get_adapdata to return the v4l2_device. However, this is not always
possible on embedded platforms. So modify the API to pass the v4l2_device
pointer explicitly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add utility function to probe for a single address, rather than a list
of addresses.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Originally the intention was to switch to the new style i2c API starting with
the introduction of the API in 2.6.22. However, the i2c_new_probed_device()
function has a lethal bug that wasn't fixed until 2.6.25. Or more accurately,
it was only fixed in the stable series of 2.6.25 and 2.6.26.
Given the fact that the new i2c API also changed starting with 2.6.26 (the
addition of i2c_device_id), it is easiest to switch APIs starting with
2.6.26.
This patch updates all the legacy code accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_std didn't belong in the tuner ops. Stricly speaking it should be part of
the video ops, but it is used by audio and tuner devices as well, so it is
more efficient to make it part of the core ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init callback was used in several places to load firmware. Make a separate
load_fw callback for that. This makes the code a lot more understandable.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_standby is only used to put the tuner in powersaving mode, so move it
from core to tuner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that all drivers are converted to v4l2_subdev we can remove legacy code
in v4l2-common. Also move the documentation of the internal API to
v4l2-subdev.h where it really belongs.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-subdev.c and v4l2-i2c-drv-legacy.h were used to support the old i2c
API. All v4l drivers are now converted to v4l2_subdev, so these two files
can be removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is common code shared between the IDE and libata implementations
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.infradead.org/mtd-2.6: (53 commits)
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] [NOR] Fixup for Numonyx M29W128 chips
[MTD] mtdpart: Make ecc_stats more realistic.
powerpc/85xx: TQM8548: Update DTS file for multi-chip support
powerpc: NAND: FSL UPM: document new bindings
[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
[MTD] [NAND] FSL-UPM: add multi chip support
[MTD] [NOR] Add device parent info to physmap_of
[MTD] [NAND] Add support for NAND on the Socrates board
[MTD] [NAND] Add support for 4KiB pages.
[MTD] sysfs support should not depend on CONFIG_PROC_FS
[MTD] [NAND] Add parent info for CAFÉ controller
[MTD] support driver model updates
[MTD] driver model updates (part 2)
[MTD] driver model updates
[MTD] [NAND] move gen_nand's probe function to .devinit.text
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
[MTD] fix use after free in register_mtd_blktrans
[MTD] [MAPS] Drop now unused sharpsl-flash map
[MTD] ofpart: Check name property to determine partition nodes.
...
Manually fix trivial conflict in drivers/mtd/maps/Makefile
Fixes:
In file included from drivers/serial/mux.c:37:
include/linux/serial_core.h: In function 'uart_handle_sysrq_char':
include/linux/serial_core.h:467: error: 'struct uart_port' has no member named 'sysrq'
include/linux/serial_core.h:468: error: 'struct uart_port' has no member named 'sysrq'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implements basic support for all 843x RS232 devices, but does not
add DMA support. This means that sustained data transfers at high baud
rates may not be possible on multiple ports simultaneously.
Signed-off-by: Shawn Bohrer <shawn.bohrer@ni.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'kmemtrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
kmemtrace: trace kfree() calls with NULL or zero-length objects
kmemtrace: small cleanups
kmemtrace: restore original tracing data binary format, improve ABI
kmemtrace: kmemtrace_alloc() must fill type_id
kmemtrace: use tracepoints
kmemtrace, rcu: don't include unnecessary headers, allow kmemtrace w/ tracepoints
kmemtrace, rcu: fix rcupreempt.c data structure dependencies
kmemtrace, rcu: fix rcu_tree_trace.c data structure dependencies
kmemtrace, rcu: fix linux/rcutree.h and linux/rcuclassic.h dependencies
kmemtrace, mm: fix slab.h dependency problem in mm/failslab.c
kmemtrace, kbuild: fix slab.h dependency problem in lib/decompress_unlzma.c
kmemtrace, kbuild: fix slab.h dependency problem in lib/decompress_bunzip2.c
kmemtrace, kbuild: fix slab.h dependency problem in lib/decompress_inflate.c
kmemtrace, squashfs: fix slab.h dependency problem in squasfs
kmemtrace, befs: fix slab.h dependency problem
kmemtrace, security: fix linux/key.h header file dependencies
kmemtrace, fs: fix linux/fdtable.h header file dependencies
kmemtrace, fs: uninline simple_transaction_set()
kmemtrace, fs, security: move alloc_secdata() and free_secdata() to linux/security.h
* 'for-2.6.30' of git://linux-nfs.org/~bfields/linux: (81 commits)
nfsd41: define nfsd4_set_statp as noop for !CONFIG_NFSD_V4
nfsd41: define NFSD_DRC_SIZE_SHIFT in set_max_drc
nfsd41: Documentation/filesystems/nfs41-server.txt
nfsd41: CREATE_EXCLUSIVE4_1
nfsd41: SUPPATTR_EXCLCREAT attribute
nfsd41: support for 3-word long attribute bitmask
nfsd: dynamically skip encoded fattr bitmap in _nfsd4_verify
nfsd41: pass writable attrs mask to nfsd4_decode_fattr
nfsd41: provide support for minor version 1 at rpc level
nfsd41: control nfsv4.1 svc via /proc/fs/nfsd/versions
nfsd41: add OPEN4_SHARE_ACCESS_WANT nfs4_stateid bmap
nfsd41: access_valid
nfsd41: clientid handling
nfsd41: check encode size for sessions maxresponse cached
nfsd41: stateid handling
nfsd: pass nfsd4_compound_state* to nfs4_preprocess_{state,seq}id_op
nfsd41: destroy_session operation
nfsd41: non-page DRC for solo sequence responses
nfsd41: Add a create session replay cache
nfsd41: create_session operation
...
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: introduce lp5521 led driver
leds: just ignore invalid GPIOs in leds-gpio
leds: Fix &&/|| confusion in leds-pca9532.c
leds: move h1940-leds's probe function to .devinit.text
leds: remove an unnecessary "goto" on drivers/leds/leds-s3c24.c
leds: add BD2802GU LED driver
leds: remove experimental flag from leds-clevo-mail
leds: Prevent multiple LED triggers with the same name
leds: Add gpio-led trigger
leds: Add rb532 LED driver for the User LED
leds: Add suspend/resume state flags to leds-gpio
leds: simple driver for pwm driven LEDs
leds: Fix leds-gpio driver multiple module_init/exit usage
leds: Add dac124s085 driver
leds: allow led-drivers to use a variable range of brightness values
leds: Add openfirmware platform device support
This patch sets up disabled bridges even if buses have already been
added.
pci_assign_unassigned_resources is called after buses are added.
pci_assign_unassigned_resources calls pci_bus_assign_resources.
pci_bus_assign_resources calls pci_setup_bridge to configure BARs of
bridges.
Currently pci_setup_bridge returns immediately if the bus have already
been added. So pci_assign_unassigned_resources can't configure BARs of
bridges that were added in a disabled state; this patch fixes the issue.
On logical hot-add, we need to prevent the kernel from re-initializing
bridges that have already been initialized. To achieve this,
pci_setup_bridge returns immediately if the bridge have already been
enabled.
We don't need to check whether the specified bus is a root bus or not.
pci_setup_bridge is not called on a root bus, because a root bus does
not have a bridge.
The patch adds a new helper function, pci_is_enabled. I made the
function name similar to pci_is_managed. The codes which use
enable_cnt directly are changed to use pci_is_enabled.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fixes the following compiler error:
fs/nfsd/nfssvc.c: In function 'set_max_drc':
fs/nfsd/nfssvc.c:240: error: 'NFSD_DRC_SIZE_SHIFT' undeclared
CONFIG_NFSD_V4 is not set
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
The new i2c binding model makes the client_register and
client_unregister methods of struct i2c_adapter useless, so we can
remove them with the rest of the legacy model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch fixes a regression (introduced by myself in commit 19abb7b:
netfilter: ctnetlink: deliver events for conntracks changed from
userspace) that results in an expectation re-insertion since
__nf_ct_expect_check() may return 0 for expectation timer refreshing.
This patch also removes a unnecessary refcount bump that
pretended to avoid a possible race condition with event delivery
and expectation timers (as said, not needed since we hold a
reference to the object since until we finish the expectation
setup). This also merges nf_ct_expect_related_report() and
nf_ct_expect_related() which look basically the same.
Reported-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
ROHM BD2802GU is a RGB LED controller attached to i2c bus and specifically
engineered for decoration purposes. This RGB controller incorporates
lighting patterns and illuminates.
This driver is designed to minimize power consumption, so when there is no
emitting LED, it enters to reset state. And because the BD2802GU has lots
of features that can't be covered by the current LED framework, it
provides Advanced Configuration Function(ADF) mode, so that user
applications can set registers of BD2802GU directly.
Here are basic usage examples :
; to turn on LED (not blink)
$ echo 1 > /sys/class/leds/led1_R/brightness
; to blink LED
$ echo timer > /sys/class/leds/led1_R/trigger
$ echo 1 > /sys/class/leds/led1_R/delay_on
$ echo 1 > /sys/class/leds/led1_R/delay_off
; to turn off LED
$ echo 0 > /sys/class/leds/led1_R/brightness
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add an option to preserve LED state when suspending/resuming to the LED
gpio driver. Based on a suggestion from Robert Jarzmik.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add a simple driver for pwm driver LEDs. pwm_id and period can be defined
in board file. It is developed for pxa, however it is probably generic
enough to be used on other platforms with pwm.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This patch allows drivers to override the default maximum brightness value
of 255. We take care to preserve backwards-compatibility as much as
possible, so that user-space ABI doesn't change for existing drivers.
LED trigger code has also been updated to use the per-LED maximum.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
By default, CFQ will anticipate more IO from a given io context if the
previously completed IO was sync. This used to be fine, since the only
sync IO was reads and O_DIRECT writes. But with more "normal" sync writes
being used now, we don't want to anticipate for those.
Add a bio/request flag that informs the IO scheduler that this is a sync
request that we should not idle for. Introduce WRITE_ODIRECT specifically
for O_DIRECT writes, and make sure that the other sync writes set this
flag.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(S)WRITE_SYNC always unplugs the device right after IO submission.
Sometimes we want to build up a queue before doing so, so add
variants that explicitly DON'T unplug the queue. The caller must
then do that after submitting all the IO.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes sure that we never wait on async IO for sync requests, instead
of doing the split on writes vs reads.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently the 9p code crashes when a operation is interrupted, i.e. for
example when the user presses ^C while reading from a file.
This patch fixes the code that is responsible for interruption and flushing
of 9P operations.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide-cd: fix REQ_QUIET tests in cdrom_decode_status
Fix up trivial conflicts in include/linux/blkdev.h
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: document the multi-touch (MT) protocol
Input: add detailed multi-touch finger data report protocol
Input: allow certain EV_ABS events to bypass all filtering
Input: bcm5974 - add documentation for the driver
Input: bcm5974 - augment debug information
Input: bcm5974 - Add support for the Macbook 5 (Unibody)
Input: bcm5974 - add quad-finger tapping
Input: bcm5974 - prepare for a new trackpad header type
Input: appletouch - fix DMA to/from stack buffer
Input: wacom - fix TabletPC touch bug
Input: lifebook - add DMI entry for Fujitsu B-2130
Input: ALPS - add signature for Toshiba Satellite Pro M10
Input: elantech - make sure touchpad is really in absolute mode
Input: elantech - provide a workaround for jumpy cursor on firmware 2.34
Input: ucb1400 - use disable_irq_nosync() in irq handler
Input: tsc2007 - use disable_irq_nosync() in irq handler
Input: sa1111ps2 - use disable_irq_nosync() in irq handlers
Input: omap-keypad - use disable_irq_nosync() in irq handler
See http://bugzilla.kernel.org/show_bug.cgi?id=13034
If the port gets into a TIME_WAIT state, then we cannot reconnect without
binding to a new port.
Tested-by: Petr Vandrovec <petr@vandrovec.name>
Tested-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Committed_AS field can underflow in certain situations:
> # while true; do cat /proc/meminfo | grep _AS; sleep 1; done | uniq -c
> 1 Committed_AS: 18446744073709323392 kB
> 11 Committed_AS: 18446744073709455488 kB
> 6 Committed_AS: 35136 kB
> 5 Committed_AS: 18446744073709454400 kB
> 7 Committed_AS: 35904 kB
> 3 Committed_AS: 18446744073709453248 kB
> 2 Committed_AS: 34752 kB
> 9 Committed_AS: 18446744073709453248 kB
> 8 Committed_AS: 34752 kB
> 3 Committed_AS: 18446744073709320960 kB
> 7 Committed_AS: 18446744073709454080 kB
> 3 Committed_AS: 18446744073709320960 kB
> 5 Committed_AS: 18446744073709454080 kB
> 6 Committed_AS: 18446744073709320960 kB
Because NR_CPUS can be greater than 1000 and meminfo_proc_show() does
not check for underflow.
But NR_CPUS proportional isn't good calculation. In general,
possibility of lock contention is proportional to the number of online
cpus, not theorical maximum cpus (NR_CPUS).
The current kernel has generic percpu-counter stuff. using it is right
way. it makes code simplify and percpu_counter_read_positive() don't
make underflow issue.
Reported-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Eric B Munson <ebmunson@us.ibm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: <stable@kernel.org> [All kernel versions]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers using of_register_platform_driver() wrapper break on sparc
because the wrapper isn't in the header file. This patch moves it from
Microblaze and PowerPC implementations and makes it common code.
Fixes this sparc64 allmodconfig build error (at least):
drivers/leds/leds-gpio.c: In function `gpio_led_init':
drivers/leds/leds-gpio.c:295: error: implicit declaration of function `of_register_platform_driver'
drivers/leds/leds-gpio.c: In function `gpio_led_exit':
drivers/leds/leds-gpio.c:311: error: implicit declaration of function `of_unregister_platform_driver'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the problem introduced by commit 3bfacef412 (get rid of
special-casing the /sbin/loader on alpha): osf/1 ecoff binary segfaults
when binfmt_aout built as module. That happens because aout binary
handler gets on the top of the binfmt list due to late registration, and
kernel attempts to execute the binary without preparatory work that must
be done by binfmt_loader.
Fixed by changing the registration order of the default binfmt handlers
using list_add_tail() and introducing insert_binfmt() function which
places new handler on the top of the binfmt list. This might be generally
useful for installing arch-specific frontends for default handlers or just
for overriding them.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Richard Henderson <rth@twiddle.net
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current mem_cgroup_shrink_usage() has two problems.
1. It doesn't call mem_cgroup_out_of_memory and doesn't update
last_oom_jiffies, so pagefault_out_of_memory invokes global OOM.
2. Considering hierarchy, shrinking has to be done from the
mem_over_limit, not from the memcg which the page would be charged to.
mem_cgroup_try_charge_swapin() does all of these things properly, so we
use it and call cancel_charge_swapin when it succeeded.
The name of "shrink_usage" is not appropriate for this behavior, so we
change it too.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.cn>
Cc: Paul Menage <menage@google.com>
Cc: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a linux-next allyesconfig build:
kernel/trace/ring_buffer.c:1726:
warning: passing argument 1 of 'atomic_cmpxchg' from incompatible pointer type
linux-next/arch/s390/include/asm/atomic.h:112:
note: expected 'struct atomic_t *' but argument is of type 'struct atomic64_t *'
atomic_long_cmpxchg and atomic_long_xchg are incorrectly defined for 64
bit architectures. They should be mapped to the atomic64_* variants.
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original patch (dfa4411cc3) was buggy.
This is a more proper fix which introduces blk_rq_quiet() macro
alleviating the need for dumb, too short caching variables.
Thanks to Helge Deller and Bart for debugging this.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-and-tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In order to utilize the full power of the new multi-touch devices, a
way to report detailed finger data to user space is needed. This patch
adds a multi-touch (MT) protocol which allows drivers to report details
for an arbitrary number of fingers.
The driver sends a SYN_MT_REPORT event via the input_mt_sync() function
when a complete finger has been reported.
In order to stay compatible with existing applications, the data
reported in a finger packet must not be recognized as single-touch
events. In addition, all finger data must bypass input filtering,
since subsequent events of the same type refer to different fingers.
A set of ABS_MT events with the desired properties are defined. The
events are divided into categories, to allow for partial implementation.
The minimum set consists of ABS_MT_TOUCH_MAJOR, ABS_MT_POSITION_X and
ABS_MT_POSITION_Y, which allows for multiple fingers to be tracked.
If the device supports it, the ABS_MT_WIDTH_MAJOR may be used to provide
the size of the approaching finger. Anisotropy and direction may be
specified with ABS_MT_TOUCH_MINOR, ABS_MT_WIDTH_MINOR and
ABS_MT_ORIENTATION. Devices with more granular information may specify
general shapes as blobs, i.e., as a sequence of rectangular shapes
grouped together by a ABS_MT_BLOB_ID. Finally, the ABS_MT_TOOL_TYPE
may be used to specify whether the touching tool is a finger or a pen.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The integrated button on the new unibody Macbooks presents a need to
report explicit four-finger actions. Evidently, the finger pressing
the button is also touching the trackpad, so in order to fully support
three-finger actions, the driver must be able to report four-finger
actions. This patch adds a new button, BTN_TOOL_QUADTAP, which
achieves this.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
OSC's OSD2 target: [git clone git://git.open-osd.org/osc-osd/ master]
(Initiator code prior to this patch must use: "git checkout CDB_VER_OSD2r01"
in the target tree above)
This is a summery of the wire changes:
* OSDv2_ADDITIONAL_CDB_LENGTH == 192 => 228 (Total CDB is now 236 bytes)
* Attributes List Element Header grew, so attribute values are 8 bytes
aligned.
* Cryptographic keys and signatures are 20 => 32
* Few new definitions.
(Still missing new standard definitions attribute values, these do not change
wire format and will be added later when needed)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In OSD2r04 draft, cryptographic key size changed to 32 bytes from
OSD1's 20 bytes. This causes a couple of on-the-wire structures
to change, including the CDB.
In this patch the OSD1/OSD2 handling is separated out in regard
to affected structures, but on-the-wire is still the same. All
on the wire changes will be submitted in one patch for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In OSD2r05 draft each attribute list element header was changed
so attribute-value would be 8 bytes aligned. In OSD2r01-r04
it was aligned on 2 bytes. (This is because in OSD2r01 the complete
element was 8 bytes padded at end but the header was not adjusted
and caused permanent miss-alignment.)
OSD1 elements are not padded and might be or might not be aligned.
OSD1 is still supported.
In this code we do all the code re-factoring to separate OSD1/OSD2
differences but do not change actual wire format. All wire format
changes will happen in one patch later, for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When building with a .config generated from 'make allmodconfig'
some build warnings are generated. This patch corrects the warnings,
adds a FC_FID_NONE (= 0) enumeration for FC-IDs and cleans up one
variable naming to meet our variable naming conventions. For example,
fc_lport's should be named "lport," not "lp."
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rogue ports are currently not tracked on any list. The only reference
to them is through any outstanding exchanges pending on the rogue ports.
If the module is removed while a retry is set on a rogue port
(say a Plogi retry for instance), this retry is not cancelled because there
is no reference to the rogue port in the discovery rports list. Thus the
local port can clean itself up, delete the exchange pool, and then the
rogue port timeout can fire and try to start up another exchange.
This patch tracks the rogue ports in a new list disc->rogue_rports. Creating
a new list instead of using the disc->rports list keeps remote port code
change to a minimum.
1) Whenever a rogue port is created, it is immediately added to the
disc->rogue_rports list.
2) When the rogues port goes to ready, it is removed from the rogue list
and the real remote port is added to the disc->rports list
3) The removal of the rogue from the disc->rogue_rports list is done in
the context of the fc_rport_work() workQ thread in discovery callback.
4) Real rports are removed from the disc->rports list like before. Lookup
is done only in the real rports list. This avoids making large changes
to the remote port code.
5) In fc_disc_stop_rports, the rogues list is traversed in addition to the
real list to stop the rogue ports and issue logoffs on them. This way, rogue
ports get cleaned up when the local port goes away.
6) rogue remote ports are not removed from the list right away, but
removed late in fc_rport_work() context, multiple threads can find the same
remote port in the list and call rport_logoff(). Rport_logoff() only
continues with the logoff if port is not in NONE state, thus preventing
multiple logoffs and multiple list deletions.
7) Since the rport is removed from the disc list at a later stage
(in the disc callback), incoming frames can find the rport even if
rport_logoff() has been called on the rport. When rport_logoff() is called,
the rport state is set to NONE, and we are trying to cancel all exchanges
and retries on that port. While in this state, if an incoming
Plogi/Prli/Logo or other frames match the rport, we should not reply
because the rport is in the NONE state. Just drop the frame, since the
rport will be deleted soon in the disc callback (fc_rport_work)
8) In fc_disc_single(), remove rport lookup and call to fc_disc_del_target.
fc_disc_single() is called from recv_rscn_req() where rport lookup
and rport_logoff is already done.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-next' of git://git.o-hand.com/linux-mfd:
mfd: fix da903x warning
mfd: fix MAINTAINERS entry
mfd: Use the value of the final spin when reading the AUXADC
mfd: Storage class should be before const qualifier
mfd: PASIC3: supply clock_rate to DS1WM via driver_data
mfd: remove DS1WM clock handling
mfd: remove unused PASIC3 bus_shift field
pxa/magician: remove deprecated .bus_shift from PASIC3 platform_data
mfd: convert PASIC3 to use MFD core
mfd: convert DS1WM to use MFD core
mfd: Support active high IRQs on WM835x
mfd: Use bulk read to fill WM8350 register cache
mfd: remove duplicated #include from pcf50633
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-cpumask: (36 commits)
cpumask: remove cpumask allocation from idle_balance, fix
numa, cpumask: move numa_node_id default implementation to topology.h, fix
cpumask: remove cpumask allocation from idle_balance
x86: cpumask: x86 mmio-mod.c use cpumask_var_t for downed_cpus
x86: cpumask: update 32-bit APM not to mug current->cpus_allowed
x86: microcode: cleanup
x86: cpumask: use work_on_cpu in arch/x86/kernel/microcode_core.c
cpumask: fix CONFIG_CPUMASK_OFFSTACK=y cpu hotunplug crash
numa, cpumask: move numa_node_id default implementation to topology.h
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
cpumask: remove x86 cpumask_t uses.
cpumask: use cpumask_var_t in uv_flush_tlb_others.
cpumask: remove cpumask_t assignment from vector_allocation_domain()
cpumask: make Xen use the new operators.
cpumask: clean up summit's send_IPI functions
cpumask: use new cpumask functions throughout x86
x86: unify cpu_callin_mask/cpu_callout_mask/cpu_initialized_mask/cpu_sibling_setup_mask
cpumask: convert struct cpuinfo_x86's llc_shared_map to cpumask_var_t
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
x86: unify 32 and 64-bit node_to_cpumask_map
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
module: use strstarts()
strstarts: helper function for !strncmp(str, prefix, strlen(prefix))
arm: allow usage of string functions in linux/string.h
module: don't use stop_machine on module load
module: create a request_module_nowait()
module: include other structures in module version check
module: remove the SHF_ALLOC flag on the __versions section.
module: clarify the force-loading taint message.
module: Export symbols needed for Ksplice
Ksplice: Add functions for walking kallsyms symbols
module: remove module_text_address()
module: __module_address
module: Make find_symbol return a struct kernel_symbol
kernel/module.c: fix an unused goto label
param: fix charp parameters set via sysfs
Fix trivial conflicts in kernel/extable.c manually.
* 'printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
printk: correct the behavior of printk_timed_ratelimit()
vsprintf: unify the format decoding layer for its 3 users, cleanup
fix regression from "vsprintf: unify the format decoding layer for its 3 users"
vsprintf: fix bug in negative value printing
vsprintf: unify the format decoding layer for its 3 users
vsprintf: add binary printf
printk: introduce printk_once()
Fix trivial conflicts (printk_once vs log_buf_kexec_setup() added near
each other) in include/linux/kernel.h.
This patch adds support for ACPI device driver .notify() methods. If
such a method is present, Linux/ACPI installs a handler for device
notifications (but not for system notifications such as Bus Check,
Device Check, etc). When a device notification occurs, Linux/ACPI
passes it on to the driver's .notify() method.
In most cases, this removes the need for drivers to install their own
handlers for device-specific notifications.
For fixed hardware devices like some power and sleep buttons, there's
no notification value because there's no control method to execute a
Notify opcode. When a fixed hardware device generates an event, we
handle it the same as a regular device notification, except we send
a ACPI_FIXED_HARDWARE_EVENT value. This is outside the normal 0x0-0xff
range used by Notify opcodes.
Several drivers install their own handlers for system Bus Check and
Device Check notifications so they can support hot-plug. This patch
doesn't affect that usage.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This driver requests a clock that usually is supplied by the MFD in which
the DS1WM is contained. Currently, it is impossible for a MFD to register
their clocks with the generic clock API due to different implementations
across architectures.
For now, this patch removes the clock handling from DS1WM altogether,
trusting that the MFD enable/disable functions will switch the clock if
needed. The clock rate is obtained from a new parameter in driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Removes the now-unused bus_shift field from pasic3_platform_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch converts the DS1WM driver into an MFD cell. It also
calculates the bus_shift parameter from the memory resource size.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Instead of always splitting the file offset into 32-bit 'high' and 'low'
parts, just split them into the largest natural word-size - which in C
terms is 'unsigned long'.
This allows 64-bit architectures to avoid the unnecessary 32-bit
shifting and masking for native format (while the compat interfaces will
obviously always have to do it).
This also changes the order of 'high' and 'low' to be "low first". Why?
Because when we have it like this, the 64-bit system calls now don't use
the "pos_high" argument at all, and it makes more sense for the native
system call to simply match the user-mode prototype.
This results in a much more natural calling convention, and allows the
compiler to generate much more straightforward code. On x86-64, we now
generate
testq %rcx, %rcx # pos_l
js .L122 #,
movq %rcx, -48(%rbp) # pos_l, pos
from the C source
loff_t pos = pos_from_hilo(pos_h, pos_l);
...
if (pos < 0)
return -EINVAL;
and the 'pos_h' register isn't even touched. It used to generate code
like
mov %r8d, %r8d # pos_low, pos_low
salq $32, %rcx #, tmp71
movq %r8, %rax # pos_low, pos.386
orq %rcx, %rax # tmp71, pos.386
js .L122 #,
movq %rax, -48(%rbp) # pos.386, pos
which isn't _that_ horrible, but it does show how the natural word size
is just a more sensible interface (same arguments will hold in the user
level glibc wrapper function, of course, so the kernel side is just half
of the equation!)
Note: in all cases the user code wrapper can again be the same. You can
just do
#define HALF_BITS (sizeof(unsigned long)*4)
__syscall(PWRITEV, fd, iov, count, offset, (offset >> HALF_BITS) >> HALF_BITS);
or something like that. That way the user mode wrapper will also be
nicely passing in a zero (it won't actually have to do the shifts, the
compiler will understand what is going on) for the last argument.
And that is a good idea, even if nobody will necessarily ever care: if
we ever do move to a 128-bit lloff_t, this particular system call might
be left alone. Of course, that will be the least of our worries if we
really ever need to care, so this may not be worth really caring about.
[ Fixed for lost 'loff_t' cast noticed by Andrew Morton ]
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-api@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ralf Baechle <ralf@linux-mips.org>>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update driver model support in the MTD framework, so it fits
better into the current udev-based hotplug framework:
- Each mtd_info now has a device node. MTD drivers should set
the dev.parent field to point to the physical device, before
setting up partitions or otherwise declaring MTDs.
- Those device nodes always map to /sys/class/mtdX device nodes,
which no longer depend on MTD_CHARDEV.
- Those mtdX sysfs nodes have a "starter set" of attributes;
it's not yet sufficient to replace /proc/mtd.
- Enabling MTD_CHARDEV provides /sys/class/mtdXro/ nodes and the
/sys/class/mtd*/dev attributes (for udev, mdev, etc).
- Include a MODULE_ALIAS_CHARDEV_MAJOR macro. It'll work with
udev creating the /dev/mtd* nodes, not just a static rootfs.
So the sysfs structure is pretty much what you'd expect, except
that readonly chardev nodes are a bit quirky.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We were comparing {bus,devfn} and assuming that a match meant it was the
same device. It doesn't -- the same {bus,devfn} can exist in
multiple PCI domains. Include domain number in device identification
(and call it 'segment' in most places, because there's already a lot of
references to 'domain' which means something else, and this code is
infected with ACPI thinking already).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Implement the CREATE_EXCLUSIVE4_1 open mode conforming to
http://tools.ietf.org/html/draft-ietf-nfsv4-minorversion1-26
This mode allows the client to atomically create a file
if it doesn't exist while setting some of its attributes.
It must be implemented if the server supports persistent
reply cache and/or pnfs.
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Also, use client minorversion to generate supported attrs
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Support enabling and disabling nfsv4.1 via /proc/fs/nfsd/versions
by writing the strings "+4.1" or "-4.1" correspondingly.
Use user mode nfs-utils (rpc.nfsd option) to enable.
This will allow us to get rid of CONFIG_NFSD_V4_1
[nfsd41: disable support for minorversion by default]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
For nfs41, the open share flags are used also for
delegation "wants" and "signals". Check that they are valid.
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
When sessions are used, stateful operation sequenceid and stateid handling
are not used. When sessions are used, on the first open set the seqid to 1,
mark state confirmed and skip seqid processing.
When sessionas are used the stateid generation number is ignored when it is zero
whereas without sessions bad_stateid or stale stateid is returned.
Add flags to propagate session use to all stateful ops and down to
check_stateid_generation.
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Andy Adamson <andros@netapp.com>
[nfsd4_has_session should return a boolean, not u32]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: pass nfsd4_compoundres * to nfsd4_process_open1]
[nfsd41: calculate HAS_SESSION in nfs4_preprocess_stateid_op]
[nfsd41: calculate HAS_SESSION in nfs4_preprocess_seqid_op]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Currently we only use cstate->current_fh,
will also be used by nfsd41 code.
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Implement the destory_session operation confoming to
http://tools.ietf.org/html/draft-ietf-nfsv4-minorversion1-26
[use sessionid_lock spin lock]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
A session inactivity time compound (lease renewal) or a compound where the
sequence operation has sa_cachethis set to FALSE do not require any pages
to be held in the v4.1 DRC. This is because struct nfsd4_slot is already
caching the session information.
Add logic to the nfs41 server to not cache response pages for solo sequence
responses.
Return nfserr_replay_uncached_rep on the operation following the sequence
operation when sa_cachethis is FALSE.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: use cstate session in nfsd4_replay_cache_entry]
[nfsd41: rename nfsd4_no_page_in_cache]
[nfsd41 rename nfsd4_enc_no_page_replay]
[nfsd41 nfsd4_is_solo_sequence]
[nfsd41 change nfsd4_not_cached return]
Signed-off-by: Andy Adamson <andros@netapp.com>
[changed return type to bool]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41 drop parens in nfsd4_is_solo_sequence call]
Signed-off-by: Andy Adamson <andros@netapp.com>
[changed "== 0" to "!"]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Replace the nfs4_client cl_seqid field with a single struct nfs41_slot used
for the create session replay cache.
The CREATE_SESSION slot sets the sl_session pointer to NULL. Otherwise, the
slot and it's replay cache are used just like the session slots.
Fix unconfirmed create_session replay response by initializing the
create_session slot sequence id to 0.
A future patch will set the CREATE_SESSION cache when a SEQUENCE operation
preceeds the CREATE_SESSION operation. This compound is currently only cached
in the session slot table.
Signed-off-by: Andy Adamson<andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: use bool inuse for slot state]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: revert portion of nfsd4_set_cache_entry]
Signed-off-by: Andy Adamson <andros@netpp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Implement the create_session operation confoming to
http://tools.ietf.org/html/draft-ietf-nfsv4-minorversion1-26
Look up the client id (generated by the server on exchange_id,
given by the client on create_session).
If neither a confirmed or unconfirmed client is found
then the client id is stale
If a confirmed cilent is found (i.e. we already received
create_session for it) then compare the sequence id
to determine if it's a replay or possibly a mis-ordered rpc.
If the seqid is in order, update the confirmed client seqid
and procedd with updating the session parameters.
If an unconfirmed client_id is found then verify the creds
and seqid. If both match move the client id to confirmed state
and proceed with processing the create_session.
Currently, we do not support persistent sessions, and RDMA.
alloc_init_session generates a new sessionid and creates
a session structure.
NFSD_PAGES_PER_SLOT is used for the max response cached calculation, and for
the counting of DRC pages using the hard limits set in struct srv_serv.
A note on NFSD_PAGES_PER_SLOT:
Other patches in this series allow for NFSD_PAGES_PER_SLOT + 1 pages to be
cached in a DRC slot when the response size is less than NFSD_PAGES_PER_SLOT *
PAGE_SIZE but xdr_buf pages are used. e.g. a READDIR operation will encode a
small amount of data in the xdr_buf head, and then the READDIR in the xdr_buf
pages. So, the hard limit calculation use of pages by a session is
underestimated by the number of cached operations using the xdr_buf pages.
Yet another patch caches no pages for the solo sequence operation, or any
compound where cache_this is False. So the hard limit calculation use of
pages by a session is overestimated by the number of these operations in the
cache.
TODO: improve resource pre-allocation and negotiate session
parameters accordingly. Respect and possibly adjust
backchannel attributes.
Signed-off-by: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: Dean Hildebrand <dhildeb@us.ibm.com>
[nfsd41: remove headerpadsz from channel attributes]
Our client and server only support a headerpadsz of 0.
[nfsd41: use DRC limits in fore channel init]
[nfsd41: do not change CREATE_SESSION back channel attrs]
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[use sessionid_lock spin lock]
[nfsd41: use bool inuse for slot state]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41 remove sl_session from alloc_init_session]
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[simplify nfsd4_encode_create_session error handling]
[nfsd41: fix comment style in init_forechannel_attrs]
[nfsd41: allocate struct nfsd4_session and slot table in one piece]
[nfsd41: no need to INIT_LIST_HEAD in alloc_init_session just prior to list_add]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Replay a request in nfsd4_sequence.
Add a minorversion to struct nfsd4_compound_state.
Pass the current slot to nfs4svc_encode_compound res via struct
nfsd4_compoundres to set an NFSv4.1 DRC entry.
Signed-off-by: Andy Adamson<andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: use bool inuse for slot state]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: use cstate session in nfs4svc_encode_compoundres]
[nfsd41 replace nfsd4_set_cache_entry]
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Use no more than 1/128th of the number of free pages at nfsd startup for the
v4.1 DRC.
This is an arbitrary default which should probably end up under the control
of an administrator.
Signed-off-by: Andy Adamson <andros@netapp.com>
[moved added fields in struct svc_serv under CONFIG_NFSD_V4_1]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[fix set_max_drc calculation of sv_drc_max_pages]
[moved NFSD_DRC_SIZE_SHIFT's declaration up in header file]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Cache all the result pages, including the rpc header in rq_respages[0],
for a request in the slot table cache entry.
Cache the statp pointer from nfsd_dispatch which points into rq_respages[0]
just past the rpc header. When setting a cache entry, calculate and save the
length of the nfs data minus the rpc header for rq_respages[0].
When replaying a cache entry, replace the cached rpc header with the
replayed request rpc result header, unless there is not enough room in the
cached results first page. In that case, use the cached rpc header.
The sessions fore channel maxresponse size cached is set to NFSD_PAGES_PER_SLOT
* PAGE_SIZE. For compounds we are cacheing with operations such as READDIR
that use the xdr_buf->pages to hold data, we choose to cache the extra page of
data rather than copying data from xdr_buf->pages into the xdr_buf->head page.
[nfsd41: limit cache to maxresponsesize_cached]
[nfsd41: mv nfsd4_set_statp under CONFIG_NFSD_V4_1]
[nfsd41: rename nfsd4_move_pages]
[nfsd41: rename page_no variable]
[nfsd41: rename nfsd4_set_cache_entry]
[nfsd41: fix nfsd41_copy_replay_data comment]
[nfsd41: add to nfsd4_set_cache_entry]
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Implement the sequence operation conforming to
http://tools.ietf.org/html/draft-ietf-nfsv4-minorversion1-26
Check for stale clientid (as derived from the sessionid).
Enforce slotid range and exactly-once semantics using
the slotid and seqid.
If everything went well renew the client lease and
mark the slot INPROGRESS.
Add a struct nfsd4_slot pointer to struct nfsd4_compound_state.
To be used for sessions DRC replay.
[nfsd41: rename sequence catchthis to cachethis]
Signed-off-by: Andy Adamson<andros@netapp.com>
[pulled some code to set cstate->slot from "nfsd DRC logic"]
[use sessionid_lock spin lock]
[nfsd41: use bool inuse for slot state]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd: add a struct nfsd4_slot pointer to struct nfsd4_compound_state]
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: add nfsd4_session pointer to nfsd4_compound_state]
[nfsd41: set cstate session]
[nfsd41: use cstate session in nfsd4_sequence]
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[simplify nfsd4_encode_sequence error handling]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
We need to distinguish between client names provided by NFSv4.0 clients
SETCLIENTID and those provided by NFSv4.1 via EXCHANGE_ID when looking
up the clientid by string.
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Andy Adamson <andros@netapp.com>
[nfsd41: use boolean values for use_exchange_id argument]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: simplify match_clientid_establishment logic]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Implement the exchange_id operation confoming to
http://tools.ietf.org/html/draft-ietf-nfsv4-minorversion1-28
Based on the client provided name, hash a client id.
If a confirmed one is found, compare the op's creds and
verifier. If the creds match and the verifier is different
then expire the old client (client re-incarnated), otherwise,
if both match, assume it's a replay and ignore it.
If an unconfirmed client is found, then copy the new creds
and verifer if need update, otherwise assume replay.
The client is moved to a confirmed state on create_session.
In the nfs41 branch set the exchange_id flags to
EXCHGID4_FLAG_USE_NON_PNFS | EXCHGID4_FLAG_SUPP_MOVED_REFER
(pNFS is not supported, Referrals are supported,
Migration is not.).
Address various scenarios from section 18.35 of the spec:
1. Check for EXCHGID4_FLAG_UPD_CONFIRMED_REC_A and set
EXCHGID4_FLAG_CONFIRMED_R as appropriate.
2. Return error codes per 18.35.4 scenarios.
3. Update client records or generate new client ids depending on
scenario.
Note: 18.35.4 case 3 probably still needs revisiting. The handling
seems not quite right.
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Andy Adamosn <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: use utsname for major_id (and copy to server_scope)]
[nfsd41: fix handling of various exchange id scenarios]
Signed-off-by: Mike Sager <sager@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: reverse use of EXCHGID4_INVAL_FLAG_MASK_A]
[simplify nfsd4_encode_exchange_id error handling]
[nfsd41: embed an xdr_netobj in nfsd4_exchange_id]
[nfsd41: return nfserr_serverfault for spa_how == SP4_MACH_CRED]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Define nfsd41_dec_ops vector and add it to nfsd4_minorversion for
minorversion 1.
Note: nfsd4_enc_ops vector is shared for v4.0 and v4.1
since we don't need to filter out obsolete ops as this is
done in the decoding phase.
exchange_id, create_session, destroy_session, and sequence ops are
implemented as stubs returning nfserr_opnotsupp at this stage.
[was nfsd41: xdr stubs]
[get rid of CONFIG_NFSD_V4_1]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Simple sessionid hashing using its monotonically increasing sequence number.
Locking considerations:
sessionid_hashtbl access is controlled by the sessionid_lock spin lock.
It must be taken for insert, delete, and lookup.
nfsd4_sequence looks up the session id and if the session is found,
it calls nfsd4_get_session (still under the sessionid_lock).
nfsd4_destroy_session calls nfsd4_put_session after unhashing
it, so when the session's kref reaches zero it's going to get freed.
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[we don't use a prime for sessionid hash table size]
[use sessionid_lock spin lock]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
This patch provides basic data structures representing the nfs41
sessions and slots, plus helpers for keeping a reference count
on the session and freeing it.
Note that our server only support a headerpadsz of 0 and
it ignores backchannel attributes at the moment.
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: remove headerpadsz from channel attributes]
[nfsd41: embed nfsd4_channel in nfsd4_session]
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: use bool inuse for slot state]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41 remove sl_session from nfsd4_slot]
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Define all NFSv4.1 common operation and error code constants.
Note that some of the definitions are used by both the nfs41 client
and the server code. This patch is duplicated in the nfs41 and nfsd41
sessions patchset.
Signed-off-by: Andy Adamson<andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfs41: add exchange id flags]
Signed-off-by: Mike Sager <sager@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[removed server-only hunk changing NFSERR_REPLAY_ME]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfs41: add SEQ4_XX to nfs41-common-protocol]
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfs41: generic error code update]
[nfs41: reverse EXCHGID4_INVAL_FLAG_MASK_{A,R}]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
On an NFSv4.1 server cache miss that causes an upcall, NFS4ERR_DELAY will be
returned. It is up to the NFSv4.1 client to resend only the operations that
have not been processed.
Initialize rq_usedeferral to 1 in svc_process(). It sill be turned off in
nfsd4_proc_compound() only when NFSv4.1 Sessions are used.
Note: this isn't an adequate solution on its own. It's acceptable as a way
to get some minimal 4.1 up and working, but we're going to have to find a
way to avoid returning DELAY in all common cases before 4.1 can really be
considered ready.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[nfsd41: reverse rq_nodeferral negative logic]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[sunrpc: initialize rq_usedeferral]
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
* 'ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
s390: remove arch specific smp_send_stop()
panic: clean up kernel/panic.c
panic, smp: provide smp_send_stop() wrapper on UP too
panic: decrease oops_in_progress only after having done the panic
generic-ipi: eliminate WARN_ON()s during oops/panic
generic-ipi: cleanups
generic-ipi: remove CSD_FLAG_WAIT
generic-ipi: remove kmalloc()
generic IPI: simplify barriers and locking
* 'locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
locking: rename trace_softirq_[enter|exit] => lockdep_softirq_[enter|exit]
lockdep: remove duplicate CONFIG_DEBUG_LOCKDEP definitions
lockdep: require framepointers for x86
lockdep: remove extra "irq" string
lockdep: fix incorrect state name
