This allows other threads to run when the serial driver polls the CTS
PIN in a loop.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
This is the patch that follows Linus's modification about set_ldisc.
Graf has built and tested it on BF537 using Linus's git Tree.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
I made a change to u-boot that used the FP (Fractional Part) field of BRGR
to achieve more accurate baud rate generation. Unfortunately, the
atmel_serial driver looks at the whole BRGR register when trying to detect
the baud rate that the port is currently running at, so setting FP to a
nonzero value breaks the baud rate detection.
I'll sit on the u-boot patch for a while longer, but this is clearly a
bug in the atmel_serial driver which should be fixed.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers are using too generic "serial" name for driver_name, this
might cause issues, like this:
Freescale QUICC Engine UART device driver
proc_dir_entry 'serial' already registered
Call Trace:
[cf82de50] [c0007f7c] show_stack+0x4c/0x1ac (unreliable)
[cf82de90] [c00b03fc] proc_register+0xfc/0x1ac
[cf82dec0] [c00b05c8] create_proc_entry+0x60/0xac
[cf82dee0] [c00b23dc] proc_tty_register_driver+0x60/0x98
[cf82def0] [c016dbd8] tty_register_driver+0x1b4/0x228
[cf82df20] [c0184d70] uart_register_driver+0x144/0x194
[cf82df40] [c030a378] ucc_uart_init+0x2c/0x94
[cf82df50] [c02f21a0] kernel_init+0x98/0x27c
[cf82dff0] [c000fa74] kernel_thread+0x44/0x60
^^ The board is using ucc_uart.c and 8250.c, both registered as
"serial".
This patch fixes two drivers that are using "serial" for driver_name and
not "ttyS" for dev_name. Drivers that are using "ttyS" for dev_name, will
conflict anyway, so we don't bother with these.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-By: Timur Tabi <timur@freescale.com>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 64e9159f5d ("serial_core:
uart_set_ldisc infrastructure") introduced the ability for low-level
serial drivers to be informed when the tty ldisc changes.
However, the actual tty-layer function that does this callback for
serial devices was declared with the wrong type, having a spurious and
unused 'ldisc' argument.
This fixed the resulting compiler warning by just removing it.
Acked-by: Blithering Idiot <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty layer provides a callback that is used when the line discipline
is changed. Some hardware uses this to configure hardware specific
features such as IrDA mode on serial ports. Unfortunately the serial
layer does not provide this feature or pass it down to drivers.
Blackfin used to hack around this by rewriting the tty ops, but those are
now properly shared and const so the hack fails. Instead provide the
proper operations.
This change plus a follow up from the Blackfin guys is needed to avoid
blackfin losing features in this release.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Russell pointed out, original patch will break some serial configurations
because of the dependency of the <asm/serial.h> header file.
Revert it first and try to find out other solution later
Cc: Javier Herrero <jherrero@hvsistemas.es>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
enable_irq_wake() and disable_irq_wake() need to be balanced. However,
serial_core.c calls these for different conditions during the suspend and
resume functions...
This is causing a regular WARN_ON() as found at
http://www.kerneloops.org/search.php?search=set_irq_wake
This patch makes the conditions for triggering the _wake enable/disable
sequence identical.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the InstaShield IS-400 four port RS-232 PCI card.
Signed-off-by: Ignacio García Pérez <iggarpe@t2i.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin SPORTS UART Driver: converting BFIN->BLACKFIN
Blackfin serial driver: add extra IRQ flag for 8250 serial driver
8250 Serial Driver: Added support for 8250-class UARTs in HV Sistemas H8606 board
Blackfin arch: Fix bug - USB fails to build for BF524/BF526
Blackfin arch: update boards defconfig files
Blackfin arch: IO Port functions to read/write unalligned memory
Blackfin arch: enable a choice to provide 4M DMA memory
Blackfin arch: cleanup the icplb/dcplb multiple hit checks
Blackfin arch: Add workaround to read edge triggered GPIOs
Blackfin arch: Sync channel defines with struct dma_register dma_io_base_addr.
Blackfin arch: Check for Anomaly 05000182
[Blackfin] arch: rename bf5xx-flash to bfin-async-flash
[Blackfin] arch: Blackfin checksum annotations
Added support for 8250-class UARTs in HV Sistemas H8606 board,
modification in 8250.c driver for correct compilation with Blackfin
Besides, I think that there is more people using 8250-class UARTs
with a different hardware than the H8606 board. This code can be shared
by them.
Signed-off-by: Javier Herrero <jherrero@hvsistemas.es>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Schedule a removal for this driver. Alternative driver is available for
a while now.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (21 commits)
Blackfin Serial Driver: abstract away DLAB differences into header
Blackfin Serial Driver: macro away the IER differences between processors
[Blackfin] arch: remove useless IRQ_SW_INT defines
[Blackfin] arch: protect linux/usb/musb.h include until the driver gets mainlined
[Blackfin] arch: protect linux/usb/isp1362.h include until the driver gets mainlined
[Blackfin] arch: add EBIU supporting for BF54x EZKIT SMSC LAN911x/LAN921x families embedded ethernet driver
[Blackfin] arch: Set spi flash partition on bf527 as like bf548.
[Blackfin] arch: fix bug - Remove module will not free L1 memory used
[Blackfin] arch: fix wrong header name in comment
[Blackfin] arch: Fix BUG - spi flash on bf527 ezkit would fail at mount
[Blackfin] arch: add twi_lcd and twi_keypad i2c board info to bf527-ezkit
[Blackfin] arch: Add physmap partition for BF527-EZkit
[Blackfin] arch: fix gdb testing regression
[Blackfin] arch: disable single stepping when delivering a signal
[Blackfin] arch: Delete unused (copied from m68k) entries in asm-offsets.c.
[Blackfin] arch: In the double fault handler, set up the PT_RETI slot
[Blackfin] arch: Support for CPU_FREQ and NOHZ
[Blackfin] arch: Functional power management support: Add CPU and platform voltage scaling support
[Blackfin] arch: fix bug - breaking the atomic sections code.
[Blackfin] arch: Equalize include files: Add VR_CTL masks
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (37 commits)
SH: catch negative denormal_subf1() retval in denormal_add()
sh: Fix DMAC base address for SH7709S
sh: update smc91x platform data for se7206.
sh: Stub in cpu_to_node() and friends for NUMA build.
sh: intc register modify fix
sh: no high level trigger on some sh3 cpus
sh: clean up sh7710 and sh7720 intc tables
sh: add interrupt ack code to sh3
sh: unify external irq pin code for sh3
sh-sci: avoid writing to nonexistent registers
sh-sci: sh7722 lacks scsptr registers
sh-sci: improve sh7722 support
sh: reset hardware from early printk
sh: drain and wait for early printk
sh: use sci_out() for early printk
sh: add memory resources to /proc/iomem
sh: add kernel bss resource
sh: fix sh7705 interrupt vector typo
sh: update smc91x platform data for se7722
sh: update smc91x platform data for MigoR
...
I noticed that
static void uart_flush_buffer(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
struct uart_port *port = state->port;
unsigned long flags;
/*
* This means you called this function _after_ the port was
* closed. No cookie for you.
*/
if (!state || !state->info) {
WARN_ON(1);
return;
}
is too late for checking state != NULL.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only write to hardware in SCI_OUT() if the register size is valid.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh7722 serial ports all lack SCSPTR registers, so mark them as
nonexistent in the register table.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve sh7722 support for SCIF1 and SCIF2 and separate code
from sh7366 implementation.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
mpc52xx_uart_int and __uart_put_char both try to acquire the
port->lock. Therefore the function sequence of:
mpc52xx_uart_int--> ...-->flush_to_ldisc-->...-->__uart_put_char
can potentially trigger a deadlock. To avoid this deadlock a fix
similar to that found in the 8250.c serial driver is applied. The
deadlock is avoided by releasing the lock before pushing a buffer
and reacquiring it when completed.
Signed-off-by: Andrew Liu <shengping.liu@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add new PCI Express Neo/JSM board to the supported list of drivers in
the JSM driver.
Signed-off-by: Scott Kilau <scottk@digi.com>
Acked-by: Ananda V <avenkat@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Operations are now a shared const function block as with most other Linux
objects
- Introduce wrappers for some optional functions to get consistent behaviour
- Wrap put_char which used to be patched by the tty layer
- Document which functions are needed/optional
- Make put_char report success/fail
- Cache the driver->ops pointer in the tty as tty->ops
- Remove various surplus lock calls we no longer need
- Remove proc_write method as noted by Alexey Dobriyan
- Introduce some missing sanity checks where certain driver/ldisc
combinations would oops as they didn't check needed methods were present
[akpm@linux-foundation.org: fix fs/compat_ioctl.c build]
[akpm@linux-foundation.org: fix isicom]
[akpm@linux-foundation.org: fix arch/ia64/hp/sim/simserial.c build]
[akpm@linux-foundation.org: fix kgdb]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Stop drivers calling their own flush method indirectly, it obfuscates code
and it will change soon anyway
- A few more lock_kernel paths temporarily needed in some driver internal
waiting code
- Remove private put_char method that does a write call for one char - we
have that anyway
- Most but not yet all of the termios copy under lock fixing (some has other
dependencies to follow)
- Note a few locking bugs in drivers found in the process
- Kill remaining [ab]users of TIOCG/SSOFTCAR in the driver, these must go to
fix the termios locking
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of checking for the BKL in these methods, take it ourselves. That
avoids propogating it into the serial drivers and we can then fix them later
on.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Noticed while auditing the code for the BKL elimination project
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If CONFIG_PPC_MPC5121 is not set, then the of_device_id table for the
mpc5200 serial driver will not get terminated with a NULL entry.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
port->irq is unsigned, platform_get_irq() may return signed unnoticed
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the code registering the Alchemy UART platform devices from
drivers/serial/ to its proper place, into the Alchemy platform code. Fix
the related Kconfig entry, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the semantic patch making this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@ change_compare_np @
expression E;
@@
(
- jiffies <= E
+ time_before_eq(jiffies,E)
|
- jiffies >= E
+ time_after_eq(jiffies,E)
|
- jiffies < E
+ time_before(jiffies,E)
|
- jiffies > E
+ time_after(jiffies,E)
)
@ include depends on change_compare_np @
@@
#include <linux/jiffies.h>
@ no_include depends on !include && change_compare_np @
@@
#include <linux/...>
+ #include <linux/jiffies.h>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Koeller had reported an issue where a device that had been making use
of the UART_BUG_TXEN code in the 8250 driver was mistakenly being caught by
the backup timer test, causing the device to work improperly.
To fix this, tighten the test requirements to enable the backup timer
workaround.
The backup timer is really meant to catch UARTs that don't re-assert the THRE
interrupt. The expectation is that they do initially assert THRE. This patch
clarifies the test.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Cc: Thomas Koeller <thomas@koeller.dyndns.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russell King noticed this one: We have to avoid replacing B0 when we pick a
baud rate for a "hung up" port. Ugly but the proper fix is in the tty layer
and means changing the tty<->serial interfaces so we will defer that for now.
[akpm@linux-foundation.org: fix uninitialised var]
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We try and write the correct speed back but the serial midlayer already
mangles the speed on us and that means if we request B0 we report back B9600
when we should not. For now we'll hack around this in the drivers and serial
code, pending a better long term solution.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings:
WARNING: drivers/serial/built-in.o(.data+0x5b8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_ite887x_exit()
WARNING: drivers/serial/built-in.o(.data+0x5e0): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x608): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x658): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x680): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x6a8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x6d0): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x6f8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x720): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x748): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
pci_serial_quirks contains a number of function pointers where the referenced
function is annotated __devexit. This is OK so we annotate pci_serial_quirks
with __refdata to ignore the __devexit references
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just the modem bits this time
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When loops reaches 0 the postfix decrement still subtracts, so the subsequent
test fails.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Johannes Weiner <hannes@saeurebad.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (49 commits)
[POWERPC] Add zImage.iseries to arch/powerpc/boot/.gitignore
[POWERPC] bootwrapper: fix build error on virtex405-head.S
[POWERPC] 4xx: Fix 460GT support to not enable FPU
[POWERPC] 4xx: Add NOR FLASH entries to Canyonlands and Glacier dts
[POWERPC] Xilinx: of_serial support for Xilinx uart 16550.
[POWERPC] Xilinx: boot support for Xilinx uart 16550.
[POWERPC] celleb: Add support for PCI Express
[POWERPC] celleb: Move miscellaneous files for Beat
[POWERPC] celleb: Move a file for SPU on Beat
[POWERPC] celleb: Move files for Beat mmu and iommu
[POWERPC] celleb: Move files for Beat hvcall interfaces
[POWERPC] celleb: Move the SCC related code for celleb
[POWERPC] celleb: Move the files for celleb base support
[POWERPC] celleb: Consolidate io-workarounds code
[POWERPC] cell: Generalize io-workarounds code
[POWERPC] Add CONFIG_PPC_PSERIES_DEBUG to enable debugging for platforms/pseries
[POWERPC] Convert from DBG() to pr_debug() in platforms/pseries/
[POWERPC] Register udbg console early on pseries LPAR
[POWERPC] Mark udbg console as CON_ANYTIME, ie. callable early in boot
[POWERPC] Set udbg_console index to 0
...
The Xilinx 16550 uart core is not a standard 16550 because it uses
word-based addressing rather than byte-based addressing. With
additional properties it is compatible with the open firmware
'ns16550' compatible binding.
This code updates the of_serial driver to handle the reg-offset
and reg-shift properties to enable this core to be used.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (85 commits)
Blackfin char driver for Blackfin on-chip OTP memory (v3)
Blackfin Serial Driver: fix bug - use mod_timer to replace only add_timer.
Blackfin Serial Driver: the uart break anomaly has been given its own number, so switch to it
Blackfin Serial Driver: use BFIN_UART_NR_PORTS to help SIR driver in uart port.
Blackfin Serial Driver: Fix bug - kernel hangs when accessing uart 0 on bf537 when booting u-boot and linux on uart 1
Blackfin Serial Driver: punt unused lsr variable
Blackfin Serial Driver: Enable IR function when user application (irattach /dev/ttyBFx -s) call TIOCSETD ioctl with line discipline N_IRDA
[Blackfin] arch: add include/boot .gitignore files
[Blackfin] arch: Functional power management support: Add support for cpu frequency scaling
[Blackfin] arch: Functional power management support: Remove broken cpu frequency scaling drivers
[Blackfin] arch: Equalize include files: Add PLL_DIV Masks
[Blackfin] arch: Add a warning about the value of CLKIN.
[Blackfin] arch: take DDR DEVWD into consideration as well for BF548
[Blackfin] arch: Remove the circular buffering mechanism for exceptions
[Blackfin] arch: lose unnecessary dependency on CONFIG_BFIN_ICACHE for MPU
[Blackfin] arch: fix bug - before assign new channel to the map register, need clear the bits first.
[Blackfin] arch: add Blackfin on-chip SIR IrDA driver support
[Blackfin] arch: BF54x memsizes are in mbits, not mbytes
[Blackfin] arch: try to remove condition that causes double fault, by checking current before it gets dereferenced
[Blackfin] arch: Update anomaly list.
...
I have a sparcstation 20 clone with a lot of on board serial ports.
The serial core code assumes that uarts are assigned contiguously
and that may not be the case when there are multiple zs devices
present. This patch insures that uart chips are placed in front of
keyboard/mouse chips in the port table.
ffd37420: ttyS0 at MMIO 0xf1100000 (irq = 44) is a zs (ESCC)
Console: ttyS0 (SunZilog zs0)
console [ttyS0] enabled
ffd37420: ttyS1 at MMIO 0xf1100004 (irq = 44) is a zs (ESCC)
ffd37500: Keyboard at MMIO 0xf1000000 (irq = 44) is a zs
ffd37500: Mouse at MMIO 0xf1000004 (irq = 44) is a zs
ffd3c5c0: ttyS2 at MMIO 0xf1100008 (irq = 44) is a zs (ESCC)
ffd3c5c0: ttyS3 at MMIO 0xf110000c (irq = 44) is a zs (ESCC)
ffd3c6a0: ttyS4 at MMIO 0xf1100010 (irq = 44) is a zs (ESCC)
ffd3c6a0: ttyS5 at MMIO 0xf1100014 (irq = 44) is a zs (ESCC)
ffd3c780: ttyS6 at MMIO 0xf1100018 (irq = 44) is a zs (ESCC)
ffd3c780: ttyS7 at MMIO 0xf110001c (irq = 44) is a zs (ESCC)
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
This patch (as1059) fixes a mistake in the way the serial core
initializes a device's wakeup settings. It should use the accessor
routine instead of relying on a macro producing an lvalue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Implement the serial polling hooks for the pl011 uart for use with
kgdboc.
This patch was specifically tested on the ARM Versatile AB reference
platform.
[ mingo@elte.hu: minor cleanups. ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the run time configuration of kgdboc such that it does not default
to 9600 baud if you use the "echo" command to configure the sysfs
module paramater.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
polled console handling support, to access a console in an irq-less
way while in debug or irq context.
absolutely zero impact as long as CONFIG_CONSOLE_POLL is disabled.
(which is the default)
[ jan.kiszka@siemens.com: lots of cleanups ]
[ mingo@elte.hu: redesign, splitups, cleanups. ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
The membase field in struct uart_port should be the the physical
address. This patch fixes it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not use hardcoded io space size. Instead use the information provided
by the resource.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We are not interested in tranceiver empty interrupts until we actually
sent a buffer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not use the URXD_CHARRDY bit for polling for new characters. This works
on i.MX1, but on MX31 the datasheet states that this bit should not be
used for polling. On MX27 it is even worse, here we get a bus error when
we access the read FIFO when no character is present.
Instead, use USR2_RDR (receive data ready) bit.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the error handling code for erroneous receive characters into
execution path. This makes the code more readable and the compiler
should know how to optimize this, right?
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the unused defines NR_PORTS and IMX_ISR_PASS_LIMIT in
the imx serial driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- get rid of `model = "UCC"' in the ucc nodes
It isn't used anywhere, so remove it. If we'll ever need something
like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
Drivers are modified for backward compatibility's sake.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch allocates parameter RAM for SMC serial ports without relying on
previous initialisation by a boot loader or a wrapper layer.
SMC parameter RAM on CPM2-based platforms can be allocated anywhere in the
general-purpose areas of the dual-port RAM. The current code relies on the
boot loader to allocate a section of general-purpose CPM RAM and gets the
section address from the device tree.
This patch modifies the device tree address usage to reference the SMC
parameter RAM base pointer instead of a pre-allocated RAM section and
allocates memory from the CPM dual-port RAM when initialising the SMC port.
CPM1-based platforms are not affected.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable serial
platform drivers, to re-enable auto loading.
NOTE that Kconfig for some of these drivers doesn't allow modular builds, and
thus doesn't match the driver source's unload support. Presumably their
unload code is buggy and/or weakly tested...
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The of_serial driver queries the current-speed property and attempts
to use it to register the custom_divisor property of the uart_port.
However, if current-speed is not set, then this code will dereference
a bad pointer. The fix is to only set custom_divisor when a
current-speed property appears in the device tree.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Strange chars appear on the serial port when a printk and a printf
happens at the same time. This is caused by the pdc sending chars while
atmel_console_write (called from printk) is executing
Concurent access of uart and console to the same port leads to corrupted
data to be transmitted, so disable tx dma (PDC) while writing to the
console.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found a problem related to losing data during pdc transmission in
atmel_serial: connect ttyS1 with ttyS2 using a loopback cable, send 30
byte of packet from one to the other and waiting for 30 byte. On the
other side just read and echo the data received.
We always call atmel_tx_dma() from the tasklet regardless of what interrupt
triggered it.
Signed-off-by: michael <trimarchi@gandalf.sssup.it>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was an off-by-1 in the SCRFDR calculation that caused writes over
128-bytes to hang in the FIFO. Fix it up.
Signed-off-by: Yutaro Ebihara <ebiharaml@si-linux.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the following section mismatches:
WARNING: drivers/built-in.o(.exit.text+0x5a): Section mismatch in reference from the function of_platform_serial_exit() to the variable .devinit.data:of_platform_serial_driver
The function __exit of_platform_serial_exit() references
a variable __devinitdata of_platform_serial_driver.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit e6bafba5b4 ("wmi: (!x & y)
strikes again"), a bug was fixed that involved converting !x & y to !(x
& y). The code below shows the same pattern, and thus should perhaps be
fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Lehmann <thomas.lehmann@alumni.tu-berlin.de> verified that this
entry works.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (35 commits)
Blackfin Serial Driver: Fix bug - Only insert UART rx char in timer task.
Blackfin Serial Driver: Fix bug - update tx dma buffer tail before wake up processes.
Blackfin Serial Driver: Fix bug - Increase buffer tail immediately before starting tx dma.
[Blackfin] serial driver: Add flow control support to bf54x
[Blackfin] serial driver: Fix bug Poll RTS/CTS status in DMA mode as well
[Blackfin] serial driver: ADSP-BF52x arch/mach support
[Blackfin] serial driver: use simpler comment headers and strip out information that is maintained in the scm's log
[Blackfin] serial driver: rework break flood anomaly handling to be more robust/realistic about what we can actually work around
[Blackfin] serial driver: fix bug - cache the bits of the LSR on systems where the LSR is read-to-clear
[Blackfin] serial driver: fix bug - should not wait for the TFI bit, just clear it when tx stop.
[Blackfin] serial driver: Fix bug serial driver in DMA mode spams history to console on shell restart
[Blackfin] serial driver: Fix bug Free rx dma buffer in shutdown.
[Blackfin] serial driver: Clean up UART DMA code.
Blackfin Serial driver: Fix bug - serial driver in PIO mode cant handle input very quickly
[Blackfin] arch: kill section mismatch warnings
[Blackfin] arch: handle the most common L1 shrinkage case (L1 does not exist for a part) so that any parts labeled for L1 instead get placed into external memory sections
[Blackfin] arch: add bfin_clear_PPIx_STATUS() helper funcs like we have for other parts
[Blackfin] arch: make sure we have proper description/copyright/license lines
[Blackfin] arch: Fix CONFIG_PM support for BF561
[Blackfin] arch: Remove DPMC char driver option
...
This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.
This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We should only return IRQ_HANDLED when we actually found something to
handle. This is important since the USART interrupt handler may be
shared with the timer interrupt on some chips.
Pointed-out-by: michael <trimarchi@gandalf.sssup.it>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm/hardware.h doesn't exist any more, and the definitions sh-sci.h
depended on are provided through asm/cpu/addrspace.h these days.
Kill off the bogus include.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7366 cpu supports. Just the most basic things like interrupt
controller, clocks and serial port are included at this point.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is an outdated comment in serial_core.c also fixed.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When possible, pass the tty name to request_irq() so that the user can easily
distinguish the different serial ports in /proc/interrupts.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by David Brownell, we really ought to be using container_of
when converting from "struct uart_port *" to "struct atmel_uart_port *".
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduced by atmel_serial-split-the-interrupt-handler.patch.
Thanks to michael <trimarchi@gandalf.sssup.it> for spotting it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is based on the DMA-patch by Chip Coldwell for the AT91/AT32 serial
USARTS, with some tweaks to make it apply neatly on top of the other patches
in this series.
The RX and TX code has been moved to a tasklet and reworked a bit. Instead of
depending on the ENDRX and TIMEOUT bits in CSR, we simply grab as much data as
we can from the DMA buffers. I think this closes a race where the ENDRX bit
is set after we read CSR but before we read RPR, although I haven't confirmed
this.
Similarly, the two TX handlers (ENDTX and TXBUFE) have been combined into one.
Since the current code only uses a single TX buffer, there's no point in
handling those interrupts separately.
This also fixes a DMA sync bug in the original patch.
[linux@bohmer.net: rebased onto irq-splitup patch]
[hskinnemoen@atmel.com: moved to tasklet, fixed dma bug, misc cleanups]
[hskinnemoen@atmel.com: atmel_serial dma: Misc fixes and cleanups]
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split up the interrupt handler of the serial port into a interrupt top-half
and a tasklet.
The goal is to get the interrupt top-half as short as possible to minimize
latencies on interrupts. But the old code also does some calls in the
interrupt handler that are not allowed on preempt-RT in IRQF_NODELAY context.
This handler is executed in this context because of the interrupt sharing with
the timer interrupt. The timer interrupt on Preempt-RT runs in IRQF_NODELAY
context.
The tasklet takes care of handling control status changes, pushing incoming
characters to the tty layer, handling break and other errors. It also handles
pushing TX data into the data register.
Reading the complete receive queue is still done in the top-half because we
never want to miss any incoming character.
[hskinnemoen@atmel.com: misc cleanups and simplifications]
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an error happens in probe(), the clocks should be disabled, but
only if the port isn't already used as a console.
In remove(), the port struct shouldn't be freed because it's defined
statically.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If BRGR is zero, the baud rate generator isn't running, so the boot loader
can't have initialized the port.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace two instances of barrier() with cpu_relax() since that's the right
thing to do when busy-waiting. This does not actually change anything since
cpu_relax() is defined as barrier() on both ARM and AVR32.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up the atmel_serial driver to conform the coding rules. It contains no
functional change.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a set of changes to implement proper resource management in the
driver, including iomem space reservation and operating on physical
addresses ioremap()ped appropriately using accessory functions rather than
unportable direct assignments.
Some adjustments to code are made to reflect the architecture of the
interface, which is a centrally controlled multiport (or, as referred to
from DEC documentation, a serial line multiplexer, going up to 8 lines
originally) rather than a bundle of separate ports.
Types are changed, where applicable, to specify the width of hardware
registers explicitly. The interrupt handler is now managed in the
->startup() and ->shutdown() calls for consistency with other drivers and
also in preparation to handle the handover from the initial firmware-based
console gracefully.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all casts from "struct uart_port *" to "struct dz_port *" with a
construct based on container_of(). This makes the conversion work
irrespective of where the former struct is located within the latter.
By popular request I have implemented it as an inline function rather than
a macro this time.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A set of changes to the way termios settings are propagated to the serial
port hardware. The DZ11 only supports a selection of fixed baud settings,
so some requests may not be fulfilled. Keep the old setting in such a case
and failing that resort to 9600bps. Also add a missing update of the
transmit timeout. And remove the explicit encoding of the line selected
from writes to the Line Parameters Register as it has been preencoded by
the ->set_termios() call already. Finally, remove a duplicate macro for
the Receiver Enable bit.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle the read and ignore status masks correctly. Handle the BREAK condition
as expected: a framing error with a null character is a BREAK, any other
framing error is a framing error indeed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ->start_tx(), ->stop_tx() and ->stop_rx() backends are called with the
port's lock already taken. Remove locking from within them and wrap around
calls as necessary.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the serial console structure so that `modpost' does not complain about
a reference to an "init" section -- "_console" is magic.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat the Kconfig entries and update descriptions for accuracy. Select the
driver by default for configurations of interest. For the curious: 32BIT
means only 32-bit DECstations support the device, not that the driver is not
64-bit clean; I have not checked that either though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sort the header inclusions, add a few that are needed but pulled indirectly
only and remove ones that are not really used.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Well, panic() is a little bit undue if request_irq() fails; there is probably
no need to justify it any further. Handle the case gracefully, by
unregistering the driver.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Polled transmission is tricky enough with the DZ11 design. While "loop" is
set to a high value, conceptually you are not allowed to transmit without
checking whether the device offers the right transmission line (yes, it is the
device that selects the line -- the driver has no control over it other than
disabling the transmitter offered if it is the wrong one), so the loop has to
be run at least once.
Well, the '1977 or PDP11 view of how serial lines should be handled... Except
that the serial interface used to be quite an impressive board back then
rather than chip.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused module function prototypes that would not even build if enabled.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When rebasing one of the mpc5200 psc UART patches I made a mistake and
damaged the patch.
This patch fixes the compile failure introduced in commit
25ae3a0739
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add 512x support using the psc_ops framework established
with the previous patch.
All 512x PSCs share the same interrupt so add
IRQF_SHARED to irq flags.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
PSC devices are different between the mpc5200 and the mpc5121
this patch localizes the differences in preparation for adding mpc5121
support to the psc uart driver.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
New serial driver for SC2681/SC2691 uarts. Older SNI RM400 machines are
using these chips for onboard serial ports.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Torben Mathiasen <device@lanana.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use SGI_HAS_ZILOG for IP22_ZILOG depends
- remove IP22 from description, because the driver works on more than
IP22 SGI machines
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Probing of the console at console_initcall time is broken. It tries to
call memory allocation routines which aren't initialized yet.
Problem solved by removing the early probe entirely. The console init
is called again anyway after the uartlite device is initialized and the
memory allocation routines can be called safely.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Mainly, this involves two changes:
1) xilinx->xlnx (recognized standard is to use the stock ticker)
2) In order to have the device tree focus on describing what the
hardware is as exactly as possible, the compatible strings contain the
full IP name and IP version.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix compile errors in the xilinxfb, xsysace and uartlite drivers used
by the Xilinx Virtex platform
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Use ARRAY_SIZE macroto get maximum ports in ColdFire serial driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clock to generate the desired baudrate with the MPSC is first divided
by the Baud Rate Generator (BRG) and then by the MPSC itself. So, when the
BRG divider is changed, the MPSC divider must also be changed to generate
the correct baudrate. During MPSC initialization, the BRG divider is
changed but the MPSC divider isn't changed until much later. This results
in some printk's coming out garbled. To fix that, set the MPSC divider at
the same time that the BRG divider is changed.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Invalid speeds are forced to 9600. Update the code for this to encode new
style baud rates properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some ports seem to be unable to drain their transmitters on shut down. Such a
problem can occur if the port is programmed for hardware imposed flow control,
characters are in the FIFO but the CTS signal is inactive.
Normally, this isn't a problem because most places where we wait for the
transmitter to drain have a time-out. However, there is no timeout in the
suspend path.
Give a port 30ms to drain; this is an arbitary value chosen to avoid long
delays if there are many such ports in the system, while giving a reasonable
chance for a single port to drain. Should a port not drain within this
timeout, issue a warning.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we boot, serial ports remain in low power mode until they're used either
by userspace or for the kernel console.
However, if you suspend the system, and then resume, all serial ports will be
taken out of low power mode. This is bad news for embedded devices where this
can mean higher power consumption.
Only bring a serial port out of low power mode if the port is being used as
the kernel console, or is in use by userspace.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the private_data field to be specified in platform_data for the
standard 8250/16550 UART. This field is used by DW APB type UARTs and
without this patch it's only possible to set this field when registering
the port by hand. If private_data is not set then the driver will
potentially oops with a NULL pointer dereference.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove dead config symbol.
Signed-off-by: Jiri Olsa <olsajiri@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Dooks <ben@fluff.org>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
with reverting "x86, serial: convert legacy COM ports to platform devices",
we will have the serial console before the port is probled again.
uart_add_one_port==>uart_configure_port==>set_mcttrl(port, 0) will clear
the DTR setting by uart_set_options(). then I will lose my output from
serial console again.
So try to keep DTR in uart_configure_port()
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove kio_addr_t, and replace it with unsigned int. No known architecture
needs more than 32 bits for IO addresses and ports and having a separate type
for it is just messy.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
* at91:
[ARM] 4802/1: Fix typo and remove vague comment
[ARM] 4660/3: at91: allow selecting UART for early kernel messages
[ARM] 4739/1: at91sam9263: make gpio bank C and D irqs work
* ixp:
[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c
[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c
[ARM] 4807/2: ixp4xx: Merge nslu2-power.c into nslu2-setup.c
[ARM] 4806/1: ixp4xx: Ethernet support for the nslu2 and nas100d boards
[ARM] 4805/1: ixp4xx: Use leds-gpio driver instead of IXP4XX-GPIO-LED driver
[ARM] 4715/2: Ethernet support for IXDP425 boards
[ARM] 4714/2: Headers for IXP4xx built-in Ethernet and WAN drivers
[ARM] 4713/3: Adds drivers for IXP4xx QMgr and NPE features
[ARM] 4712/2: Adds functions to read and write IXP4xx "feature" bits
[ARM] 4774/2: ixp4xx: Register dsmg600 rtc i2c_board_info
[ARM] 4773/2: ixp4xx: Register nas100d rtc i2c_board_info
[ARM] 4772/2: ixp4xx: Register nslu2 rtc i2c_board_info
[ARM] 4769/2: ixp4xx: Button updates for the dsmg600 board
[ARM] 4768/2: ixp4xx: Button and LED updates for the nas100d board
[ARM] 4767/2: ixp4xx: Add bitops.h include to io.h
[ARM] 4766/2: ixp4xx: Update ixp4xx_defconfig, enabling all supported boards
* master:
[ARM] 4810/1: - Fix 'section mismatch' building warnings
[ARM] xtime_seqlock: fix more ARM machines for xtime deadlocking
[ARM] 21285 serial: fix build error
* misc:
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
* pxa:
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
[ARM] pxa: fix the warning of undeclared "struct pxaohci_platform_data"
[ARM] pxa: change set_kset_name() to direct name assignment for MFP sysclass
* realview:
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
Currently early kernel messages, i.e., those from uncompression, go to the
debugging UART. And if it is enabled in the platform configuration, but
not initialized by the bootloader, the machine hangs, waiting for UART
status change. Besides, having those messages on another UART - typically
the console UART - may be preferrable. This patch allows selecting the
UART in kernel configuration.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/serial/21285.c: In function 'serial21285_set_termios':
drivers/serial/21285.c:280: error: 'tty' undeclared (first use in this function)
drivers/serial/21285.c:280: error: (Each undeclared identifier is reported only once
drivers/serial/21285.c:280: error: for each function it appears in.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use container_of() instead of assuming local uart struct is first member
of uart_port struct.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use IRQF_DISABLED instead of obsolete IRQ_FLG_STD for request_irq() flags
in m68328serial.c driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for new ColdFire serial driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add build support for new ColdFire serial driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (197 commits)
sh: add spi header and r2d platform data V3
sh: update r7780rp interrupt code
sh: remove consistent alloc stuff from the machine vector
sh: use declared coherent memory for dreamcast pci ethernet adapter
sh: declared coherent memory support V2
sh: Add support for SDK7780 board.
sh: constify function pointer tables
sh: Kill off -traditional for linker script.
cdrom: Add support for Sega Dreamcast GD-ROM.
sh: Kill off hs7751rvoip reference from arch/sh/Kconfig.
sh: Drop r7780rp_defconfig, use r7780mp_defconfig as kbuild default.
sh: Kill off dead HS771RVoIP board support.
sh: r7785rp: Fix up DECLARE_INTC_DESC() arg mismatch.
sh: r7785rp: Hook up the rest of the HL7785 FPGA IRQ vectors.
sh: r2d - enable sm501 usb host function
sh: remove voyagergx
sh: r2d - add lcd planel timings to sm501 platform data
sh: Add OHCI and UDC platform devices for SH7720.
sh: intc - remove default interrupt priority tables
sh: Correct pte size mismatch for X2 TLB.
...
Rename commproc.[ch] to cpm1.[ch] to be more consistent with cpm2. Also
rename cpm2_common.c to cpm2.c as suggested by Scott Wood. Adjust the
includes accordingly.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for the SH7263 (SH-2A) CPU.
This particular CPU is a superset of SH7203, adding some additional
peripheral blocks and hooking up additional (reserved on SH7203)
vectors in the INTC block.
No visibly nasty surprises, yet..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:
http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html
This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix. The drivers will still bind against
the older names also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently reports back the requested rate not the result of the divides
but thats an easy fix for someone with h/w
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IBM icom serial driver is using a kobject only for reference
counting, nothing else. So switch it to use a kref instead, which is
all that is needed, and is much smaller.
Cc: Anton Blanchard <anton@au.ibm.com>
Cc: Paul Mackerras <paulus@au.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ryan S. Arnold <rsa@us.ibm.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cpmux is need in all cases, having wrapped by the ifndef CONFIG_STX_GP3
was causing a compile error.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add file ucc_uart.c, a serial device driver for the Freescale QUICCEngine.
Update the Kconfig and Makefile accordingly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In preparation of adding MPC5121 support
cleanup some things that checkpatch.pl complains
about also some minor fixes suggested by
Stephen Rothwell.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This is in preparation for the addition of MPC512x
PSC support. The main difference in the 512x is
in the fifo registers.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Similar to of_find_compatible_node(), of_find_matching_node() and
for_each_matching_node() allow you to iterate over the device tree
looking for specific nodes, except that they take of_device_id
tables instead of strings.
This also moves of_match_node() from driver/of/device.c to
driver/of/base.c to colocate it with the of_find_matching_node which
depends on it.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
All the __devexit functions are now appropriately tagged. This fixes
some ppc link warnings.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We're exporting an __init function, oops :-)
The core issue here is that add_preferred_console() is marked
as __init, this makes it impossible to invoke this thing from
a driver probe routine which is what the Sparc serial drivers
need to do.
There is no harm in dropping the __init marker. This code will
actually work properly when invoked from a modular driver,
except that init will probably not pick up the console change
without some other support code.
Then we can drop the __init from sunserial_console_match()
and we're no longer exporting an __init function to modules.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cache the bits of the LSR on systems where the LSR is read-to-clear
so that we can safely read the LSR in random places. this fixes
older parts where break/framing/parity/overflow was not being detected
at all in PIO mode, and this fixes newer parts where
break/framing/parity/overflow was being reported all the time
without being cleared.
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
This patch moves the CPM command handling into commproc.c
for CPM1 and cpm2_common.c. This is yet another preparation
to get rid of drivers accessing the CPM via the global cpmp.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
This patch against 2.6.23 sparc-2.6.git contains a number of minor
cleanups of the sparc serial drivers. Initially I fixed this build
warning:
WARNING: vmlinux.o(.text+0x107a2c): Section mismatch: reference to .init.text:add_preferred_console (between 'sunserial_console_match' and 'sunserial_console_termios')
which is done by declaring sunserial_console_match() as __init. This
resulted in build warnings on sunserial_current_minor. To resolve
these the variable was changed so it is no longer global, and to hide
operations on it inside 2 new functions. These functions handle the
UART minor handling code that is common to all sparc serial drivers.
These changes allowed to clean up the uart counters in all the sparc
serial drivers, and the administration of minor device numbers.
Lastly, sunserial_console_termios() does not need to be exported since
it is only called from non-modular code.
Sadly, the following build warning still exists:
WARNING: vmlinux.o(__ksymtab+0x2910): Section mismatch: reference to .init.text:sunserial_console_match (between '__ksymtab_sunserial_console_match' and '__ksymtab_sunserial_unregister_minors')
This could be resolved by not exporting sunserial_console_match(), but
this is not possible at the moment because it is being called from
modular code. On the other hand, this is a bogus warning since it
comes from a ksymtab section.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There should be an of_node_put when breaking out of a loop that iterates
using for_each_compatible_node.
This was detected and fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
identifier d;
type T;
expression e;
iterator for_each_compatible_node;
@@
T *d;
...
for_each_compatible_node(d,...)
{... when != of_node_put(d)
when != e = d
(
return d;
|
+ of_node_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4680/1: parentheses around NR_IRQS definition
[ARM] 4679/1: AT91: Change maintainer email address
[ARM] 4675/1: pxa: fix mfp address definition error for pxa320
[ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
[ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
[ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
[ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
[ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
[ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
[ARM] uengine: fix memset size error
[ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
[ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
[ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
[ARM] 4604/2: AT91: Master clock divistor on SAM9
[ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
[ARM] PXA ssp: unlock when ssp tries to close an invalid port
[ARM] 4654/1: pxa: update default MFP register value
[ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
[ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
[ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions
- fix lockup when switching from early console to real console
- make sysrq reliable
- fix panic, if sysrq is issued before console is opened
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Output as many bytes as possible in PIO tx handler.
This reduce the number of tx interrupts and shorten the delay to handle
rx interrupt. So, rx overrun disappears.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
New and improved serial driver for CRISv10, take three, with improvements
suggested by Jiri Slaby.
- Call wait_event_interruptible with a _correct_ and sensible condition.
- Removed superfluous test of info->flags & ASYNC_CLOSING, since that is done
by wait_event_interruptible.
- Moved common code for deregistering DMA and IRQ to deinit_port function.
- Use setup_timer when initializing flush_timer.
- Convert bit-field for uses_dma_in and uses_dma_out to regular bytes.
- Removed CVS tags.
- Removed defines and comments for CRIS_BUF_SIZE and TTY_THRESHOLD_THROTTLE
(no longer used).
- Cleaned up code to pass checkpatch.
- Add crisv10.h header file.
- Merge of CRISv10 from Axis internal CVS.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"Luming Yu" <luming.yu@gmail.com> says:
There is a "ttyS1 irq is -1" problem observed on tiger4 which cause the
serial port broken.
It is because that there is __no__ ACPI IRQ resource assigned for the
serial port. So the value of the IRQ for the port is never changed since it
got initialized to -1.
If PNP supplies a valid IRQ, use it. Otherwise, leave port.irq == 0, which
means "no IRQ" to the serial core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yu Luming <luming.yu@intel.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove annoying build warnings about unused variables in atmel_serial,
which afflict both AT91 and AVR32 builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following is an extra entry to enable the touch screen on the new LG
C1 EXPRESS DUAL machine.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: remove dead config symbols from SH code
sh: Kill off broken snapgear ds1302 code.
sh: Add a dummy vga.h.
rtc: rtc-sh: Zero out tm value for invalid rtc states.
rtc: sh-rtc: Handle rtc_device_register() failure properly.
sh: Fix heartbeart on Solution Engine series
sh: Remove SCI_NPORTS from sh-sci.h
sh: Fix up PAGE_KERNEL_PCC() for nommu.
sh: hs7751rvoip: Kill off dead IPR IRQ mappings.
sh: hs7751rvoip: irq.c needs linux/interrupt.h.
sh: Kill off __{copy,clear}_user_page().
sh: Optimized copy_{to,from}_user_page() for SH-4.
sh: Wire up clear_user_highpage().
sh: Kill off the remaining ST40 cruft.
superhyway: Handle device_register() retval properly.
sh: kgdb sysrq depends on magic sysrq.
sh: Add -Werror for clean directories.
sh: Fix up kgdb build with modular sh-sci.
sh: Export __{s,u}divsi3_i4i on all CPUs.
sh: Fix up kgdb-on-NMI branch target.
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (37 commits)
[POWERPC] EEH: Make sure warning message is printed
[POWERPC] Make altivec code in swsusp_32.S depend on CONFIG_ALTIVEC
[POWERPC] windfarm: Fix windfarm thread freezer interaction
[POWERPC] Fix si_addr value on low level hash failures
[POWERPC] Refresh ppc64_defconfig and enable pasemi-related options
[POWERPC] pasemi: Update defconfig
[POWERPC] iSeries: Fix ref counting in vio setup
[POWERPC] ] Fix memset size error
[POWERPC] Fix link errors for allyesconfig
[POWERPC] iSeries_init_IRQ non-PCI tidy
[POWERPC] Change fallocate to match unistd.h on powerpc
[POWERPC] EEH: Avoid crash on null device
[POWERPC] EEH: Drivers that need reset trump others
[POWERPC] EEH: Clean up comments
[POWERPC] Fix off-by-one error in setting decrementer on Book E/4xx (v2)
[POWERPC] Fix switch_slb handling of 1T ESID values
[POWERPC] Fix build failure when CONFIG_VIRT_CPU_ACCOUNTING is not defined
[POWERPC] Include udbg.h when using udbg_printf
[POWERPC] Fix cache line vs. block size confusion
[POWERPC] Fix sysctl table check failure on PowerMac
...
When SH7710 and SH7712 are used, SCI_NPORTS redefined.
Remove it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The ST40 stuff in-tree hasn't built for some time, and hasn't been
updated for over 3 years. ST maintains their own out-of-tree changes
and rebases occasionally, and that's ultimately where all of the ST40
users go anyways.
In order for the ST40 code to be brought up to date most of the stuff
removed in this changeset would have to be rewritten anyways, so there's
very little benefit in keeping the remnants around either.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
drivers/serial/8250_early.c:80: warning: conflicting types for built-in function `putc'
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the wait_tx routine to call cpu_relax() instead of udelay() to
reduce console output latency and test for the TXFULL bit instead of
TXEMPTY. That way the FIFO doesn't need to by 100% flushed before
writing the next character.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Since commit 97d97224ff ("[SERIAL] Fix
console initialisation ordering"), serial_core calls ->pm() on
initialization even if the port was used for console.
This behaviour breaks serial_txx9 console since The serial_txx9 driver
initialize its port entirely on its ->pm() method if new state was 0.
This patch adds checking for oldstate value to fix this probelm.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Earlier patches have removed the checking for old v new differences from the
USB drivers so we can now pass in a valid blank old termios so that we don't
to fill the drivers with magic hacks for console support
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A new style serial driver for the Freescale ColdFire UART to replace
the old style one currently in the tree (drivers/serial/mcfserial.c).
Currently this UART is only found in the ColdFire CPU family of parts
(thus I prefixed this patch [M68KNOMMU]).
This has been around for a long while now, tested on all available
platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, there's a CONFIG_DISABLE_CONSOLE_SUSPEND that allows one to stop
the serial console from being suspended when the rest of the machine goes
to sleep. This is incredibly useful for debugging power management-related
things; however, having it as a compile-time option has proved to be
incredibly inconvenient for us (OLPC). There are plenty of times that we
want serial console to not suspend, but for the most part we'd like serial
console to be suspended.
This drops CONFIG_DISABLE_CONSOLE_SUSPEND, and replaces it with a kernel
boot parameter (no_console_suspend). By default, the serial console will
be suspended along with the rest of the system; by passing
'no_console_suspend' to the kernel during boot, serial console will remain
alive during suspend.
For now, this is pretty serial console specific; further fixes could be
applied to make this work for things like netconsole.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some remaining vestiges of the old hacks jsm had to work around the old
tty buffering. With the new tty buffering it simply doesn't matter any more.
[michal.k.k.piotrowski@gmail.com: fix warning]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Scott Kilau <scottk@digi.com>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove an unused symbol M32R_SIO_SHARE_IRQS from drivers/serial/m32r_sio.h.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Robert P. J. Day" <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Notebook manufacturer seems to built a newer Wacom pen enabled tablet to
recent tablet pcs which are not recognized by the serial pnp driver.
Attached is a patch which makes the newer Wacom WACF007 and WACF008 tablets
useable with the serial driver. The device is fully compatible with it.
Signed-off-by: Maik Broemme <mbroemme@plusserver.de>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UPF_FIXED_PORT flags was introduced in 2.6.22 and it can be used
instead of the driver specific verify_port routine.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable wakeup from serial ports, make it run-time configurable over sysfs,
e.g.,
echo enabled > /sys/devices/platform/serial8250.0/tty/ttyS0/power/wakeup
Requires
# CONFIG_SYSFS_DEPRECATED is not set
Following suggestions from Alan and Russell moved the may_wake_up checks
to serial_core.c. This time actually tested - it does even work. Could
someone, please, verify, that put_device after device_find_child is
correct?
Also would be nice to test with a Natsemi UART, that can wake up the system,
if such systems exist.
For this you just have to apply the patch below, issue the above "echo"
command to one of your Natsemi port, suspend and resume your system, and
verify that your Natsemi port still works. If you are actually capable of
waking up the system from that port, would be nice to test that as well.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for a whole range of boards. Some are partly autodetected but
not fully correctly others (PCI Express notably) not at all. Stick all
the right entries in.
Thanks to Mainpine for information and testing.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not include some header files already indluded by serial_core.h.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for Sierra Wireless AC850 which has the same Ids as the
AC710/750 but has a different firmware.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
[ARM] 4578/1: CM-x270: PCMCIA support
[ARM] 4577/1: ITE 8152 PCI bridge support
[ARM] 4576/1: CM-X270 machine support
[ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
[ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
[ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
[ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
[ARM] pxa: PXA3xx base support
[NET] smc91x: fix PXA DMA support code
[SERIAL] Fix console initialisation ordering
[ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
[ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
[ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
[ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
[ARM] Rename consistent_sync() as dma_cache_maint()
[ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
[ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
[ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
[ARM] 4594/1: ns9xxx: use the new gpio functions
[ARM] 4593/1: ns9xxx: implement generic clockevents
...
Ensure pm callback is called upon initialisation to place port in
correct power saving state. Ensure console is initialised prior
to deciding whether to power down the port.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (124 commits)
sh: allow building for both r2d boards in same binary.
sh: fix r2d board detection
sh: Discard .exit.text/.exit.data at runtime.
sh: Fix up some section alignments in linker script.
sh: Fix SH-4 DMAC CHCR masking.
sh: Rip out left-over nommu cond syscall cruft.
sh: Make kgdb i-cache flushing less inept.
sh: kgdb section mismatches and tidying.
sh: cleanup struct irqaction initializers.
sh: early_printk tidying.
video: pvr2fb: Add TV (RGB) support to Dreamcast PVR driver.
sh: Conditionalize gUSA support.
sh: Follow gUSA preempt changes in __switch_to().
sh: Tidy up gUSA preempt handling.
sh: __copy_user() optimizations for small copies.
sh: clkfwk: Support multi-level clock propagation.
sh: Fix URAM start address on SH7785.
sh: Use boot_cpu_data for CPU probe.
sh: Support extended mode TLB on SH-X3.
sh: Bump MAX_ACTIVE_REGIONS for SH7785.
...
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
The way the current CPM binding describes available multi-user (a.k.a.
dual-ported) RAM doesn't work well when there are multiple free regions,
and it doesn't work at all if the region doesn't begin at the start of
the muram area (as the hardware needs to be programmed with offsets into
this area). The latter situation can happen with SMC UARTs on CPM2, as its
parameter RAM is relocatable, u-boot puts it at zero, and the kernel doesn't
support moving it.
It is now described with a muram node, similar to QE. The current CPM
binding is sufficiently recent (i.e. never appeared in an official release)
that compatibility with existing device trees is not an issue.
The code supporting the new binding is shared between cpm1 and cpm2, rather
than remain separated. QE should be able to use this code as well, once
minor fixes are made to its device trees.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This prevents some bootloader/bootwrapper characters from being lost.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mostly a bunch of direct access to in/out conversions, plus a few
cast removals, __iomem annotations, and miscellaneous cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The existing OF glue code was crufty and broken. Rather than fix it,
it has been removed, and the serial driver now talks to the device tree
directly.
The non-CONFIG_PPC_CPM_NEW_BINDING code can go away once CPM platforms
are dropped from arch/ppc (which will hopefully be soon), and existing
arch/powerpc boards that I wasn't able to test on for this patchset get
converted (which should be even sooner).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reverts commit a15da8eff3
This driver is used by devices other than the xilinx opb-uartlite which
depend on bytewise access to the registers. The change to 32 bit access
does not work on these devices.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
By configuring it earlier we get console output sooner which is helpful
for debugging when the kernel crashes before the serial drivers are
initialized.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add of_platform bus binding so this driver can be used with arch/powerpc
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Tidy the comments to split the driver into logical section; the main driver,
the console driver, the platform bus binding, and module initialization
and teardown.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Separate the bus binding code from the driver structure allocation code in
preparation for adding the of_platform_bus bindings needed by arch/powerpc
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Changed to make the following OF_platform bus binding patch a wee bit cleaner
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Changed to match naming convention used in the rest of the module
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Uartlite data sheet defines the registers as 32 bit wide. This
patch changes the register access to use 32 bit transfers and eliminates
the magic +3 offset which is currently required to make the device
work.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: John Williams <jwilliams@itee.uq.edu.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
in cpm_uart_cpm1.h, DPRAM_BASE is assigned an address derived from cpmp.
On ARC=ppc, this is a physical address with 1:1 DMA mapping which can't
be used for arithmetric compare operations with virtual addresses
returned by cpm_dpram_addr. This patch changes the assignment to use
cpm_dpram_addr as well, like in cpm_uart_cpm2.h.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Include SYSRQ support for SUNSAB if SUNSAB_CONSOLE is selected
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the option for the pmac_zilog driver to use the major/minor
numbers recently allocated specifically for it (/dev/ttyPZn) instead
of the /dev/ttySn numbers. The advantage of doing this is that it
allows the pmac_zilog and 8250 drivers to coexist. The disadvantage
of doing this is that it is a user-visible ABI change and it will
break existing working setups on powermacs, and could be confusing to
users.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The kgdb console code requires uart_set_options() and friends, which
are only provided by the serial core when console support is enabled.
These were sitting under CONFIG_SH_KGDB and resulted in a link error
when console support wasn't enabled, work that by rolling the console
routines under CONFIG_SH_KGDB_CONSOLE, which they should have been
all along.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7720 (SH3-DSP) CPU.
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
drivers/serial/pmac_zilog.c:1590: warning: format '%d' expects type 'int', but argument 3 has type 'pm_message_t'
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* don't register irq until ->startup() (and release in ->shutdown()).
That avoids oopsen with the current tree when interrupt comes before we'd
set up the data structures for ttyb.
* handle console=ttyS... even when OBP talks to screen/keyboard
* register irq handler for each port, let kernel/irq/handle.c
call it for both if needed. Kills code duplication in sunsab_interrupt().
BTW, there'd been bitrot in it - ttya handling had stopped calling
check_status() on BRK (correctly), ttyb copy of that code had kept the
bogus call in that case.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use idx as index into mpc52xx_uart_nodes instead of i
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SERIAL_BFIN=m or SERIAL_MUX=m shouldn't allow SERIAL_CORE_CONSOLE=y.
Additionally, this patch fixes whitespace instead of tabs at the
SERIAL_MUX_CONSOLE option.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
resource_size_t can be either a u64 or a u32, and we can't
really know for sure, so when printing such a value out
always use long-long printf formatting and cast the argument
to that type.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI IDs for the onchip UARTs on PA Semi PWRficient.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The serial_pci driver tries to guess serial ports on unknown devices based
on the PCI class (modem or serial). On certain softmodems (AC'97 modems)
this can lead to the recognition of non-existing serial ports.
This patch adds a blacklist of PCI IDs that are to be ignored by the driver.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Christian Schmidt <schmidt@digadd.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reading the LSR clears the break, parity, frame error, and overrun bits in
the 8250 chip, but these are not being saved in all places that read the
LSR. Same goes for the MSR delta bits. Save the LSR bits off whenever the
lsr is read so they can be handled later in the receive routine. Save the
MSR bits to be handled in the modem status routine.
Also, clear the stored bits and clear the interrupt registers before
enabling interrupts, to avoid handling old values of the stored bits in the
interrupt routines.
[akpm@linux-foundation.org: clean up pre-existing code]
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This chip does not have modem control lines. Return TIOCM_CAR and
TIOCM_DSR always on get_mctrl() and ajust some bits in termios cflag.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the it887x-chips (PCI) manufactured by ITE.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The uart_set_termios() function will bail out early without bothering to
touch the hardware, if it decides that nothing "relevant" has changed.
Unfortunately, its idea of "relevant" doesn't include c_[io]speed. So if
the baud rate bits are BOTHER and you just change the speed, the change
gets optimised away.
This patch makes it ignore the old Bfoo bits in c_cflag and just check
whether c_ispeed and c_ospeed have changed. Those integers are always set
appropriately for us by set_termios().
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pending a unique anomaly id, tie the break flood issue to ANOMALY_05000230
as when that was fixed, the fallout also fixed the break flood
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
This allows debugging of problems which happen eary in the kernel
boot process (after bootargs are parsed, but before serial subsystem
is fully initialized)
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
the early setup function serial8250_console_early_setup() can be called
from non __init code (eg. hotpluggable serial ports like serial_cs) so
remove the __init from the call chain to avoid crashes.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a set of small fixes addressing points raised with the original
driver submission. In particular, __maybe_unused is used rather than a
local hack and sbd_ops is made const. Additionally I have made two local
string variables automatic as rodata space was wasted for pointers
unnecessarily.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up mpsc.c to be aligned with Documentation/CodingStyle. Also fix up some
whitespace issues.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the duplicate definition of SUPPORT_SYSRQ in mpsc driver.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the MPSC driver doesn't stop recieving characters when the CREAD
flag in termios->c_cflag is cleared. It should. Also, only start receiving
if its not already started.
Signed-off-by: Stephane Chazelas <stephane@artesyncp.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch in commit ID f7232056bf stops (aborts)
the MPSC's receive engine just before restarting it. Unfortunately, it
doesn't wait for the abort to complete before restarting it which creates a
race between the abort and the restart. If the restart occurs first, the
in-progress abort stops it again and the rx engine remains stopped.
Instead, do the abort when the SDMA engine is being stopped. Make sure to
wait for the abort to complete before continuing.
Signed-off-by: Carlos Sanchez <carlos.sanchez@gecoinc.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The serial console can select only SERIAL_VR41XX=y.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 7e92b4fc34. It broke Sébastien Dugué's
machine and Jeff said (persuasively)
This seems like it will break decades-long-working stuff, in favor of
breaking new ground in our favorite area, "trusting the BIOS."
It's just not worth it for serial ports, IMO. Serial ports are something
that just shouldn't break at this late stage in the game. My new Intel
platform boxes don't even have serial ports, so I question the value of
messing with serial port probing even more... because... just wait a year,
and your box won't have a serial port either! :)
I certainly don't object to the use of platform devices (or isa_driver),
but the probe change seems questionable. That's sorta analagous to
rewriting the floppy driver probe routine. Sure you could do it... but why
risk all that damage and go through debugging all over again?
It seems clear from this report that we cannot, should not, trust BIOS for
something (a) so simple and (b) that has been working for over a decade.
Much discussion ensued and we've decided to have another go at all of this.
Cc: Sébastien Dugué <sebastien.dugue@bull.net>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the commit 4f640efb31, "%lx" is not
suitable for p->mapbase (resource_size_t) in 32-bit. This patch fixes a
compiler warning caused by the mismatch.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.23:
sh: Fix fs.h removal from mm.h regressions.
sh: fix get_wchan() for SH kernels without framepointers
sh: arch/sh/boot - fix shell usage
rtc: rtc-sh: Correct sh_rtc_set_time() for some SH-3 parts.
sh: remove support for sh7300 and solution engine 7300
sh: Add sh to the CC_OPTIMIZE_FOR_SIZE dependencies.
sh: Kill off virt_to_bus()/bus_to_virt().
sh: sh-sci - fix SH7708 support
sh: Restrict DSP support to specific CPUs.
sh: Silence sq compile warning on sh4 nommu.
sh: Kill the rest of the SE73180 cruft.
sh: remove support for sh73180 and solution engine 73180
sh: remove old broken pint code
sh: Reclaim beginning of P3 space for vmalloc area.
sh: Fix Dreamcast DMA issues.
sh: Add kmap_coherent()/kunmap_coherent() interface for SH-4.
This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes sure the sci serial port driver compiles for sh7708.
The approach taken is to treat the sh7708 as a subset of sh7706, sh7707,
sh7709. sh7708 is very similar to sh7706, sh7707, sh7709, but only
equipped with a single sci port. The platform data in setup-sh770x.c
already limits the number of serial ports for sh7708 to a single one,
so the non-existing scif ports pointed out in sh-sci.h will remain
unused in case of sh7708.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove the legacy power management code from the 68328 serial driver.
It is not used, and there is no current kernel support for power
management on the 68328.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes old dead code:
- kill off sh73180 cpu support
- get rid of broken solution engine 73180 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
At present, various parts of the serial code use unsigned long to define
resource addresses. This is a problem, because some 32-bit platforms have
physical addresses larger than 32-bits, and have mmio serial uarts located
above the 4GB point.
This patch changes the type of mapbase in both struct uart_port and struct
plat_serial8250_port to resource_size_t, which can be configured to be 64
bits on such platforms. The mapbase in serial_struct can't safely be
changed, because that structure is user visible.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the manufacturer and card id of teltonica pcmcia modems to serial_cs.c
Signed-off-by: Attila Kinali <attila@kinali.ch>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves items of the s3c24xx support into
a new plat-s3c directory for items that use the
s3c24xx support but are not directly s3c24xx
compatible, such as the s3c2400 and s3c6400.
git mv commands:
git mv include/asm-arm/arch-s3c2410/iic.h include/asm-arm/plat-s3c/iic.h
git mv include/asm-arm/arch-s3c2410/nand.h include/asm-arm/plat-s3c/nand.h
git mv include/asm-arm/arch-s3c2410/regs-iic.h include/asm-arm/plat-s3c/regs-iic.h
git mv include/asm-arm/arch-s3c2410/regs-nand.h include/asm-arm/plat-s3c/regs-nand.h
git mv include/asm-arm/arch-s3c2410/regs-rtc.h include/asm-arm/plat-s3c/regs-rtc.h
git mv include/asm-arm/arch-s3c2410/regs-serial.h include/asm-arm/plat-s3c/regs-serial.h
git mv include/asm-arm/arch-s3c2410/regs-timer.h include/asm-arm/plat-s3c/regs-timer.h
git mv include/asm-arm/arch-s3c2410/regs-watchdog.h include/asm-arm/plat-s3c/regs-watchdog.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current scheme works on static interpretation of text names, which
is wrong.
The output-device setting, for example, must be resolved via an alias
or similar to a full path name to the console device.
Paths also contain an optional set of 'options', which starts with a
colon at the end of the path. The option area is used to specify
which of two serial ports ('a' or 'b') the path refers to when a
device node drives multiple ports. 'a' is assumed if the option
specification is missing.
This was caught by the UltraSPARC-T1 simulator. The 'output-device'
property was set to 'ttya' and we didn't pick upon the fact that this
is an OBP alias set to '/virtual-devices/console'. Instead we saw it
as the first serial console device, instead of the hypervisor console.
The infrastructure is now there to take advantage of this to resolve
the console correctly even in multi-head situations in fbcon too.
Thanks to Greg Onufer for the bug report.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the unregistration order in the i.MX serial driver
Signed-off-by: Sreekrishnan Venkateswaran <krishhna@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a reimplementation of the zs driver for the serial subsystem. Any
resemblance to the old driver is purely coincidential. ;-) I do hope I got
the handling of modem lines right -- better do not tackle me about the
issue unless you feel too good...
Any users of the old driver: please note the numbers of the serial lines
have now been swapped, i.e. ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3. It has
to do with the modem lines mentioned above; basically the port A in a given
chip has to be initialised before the port B if you want to use the latter
as the serial console (which is usually the case), as operations on modem
lines of the serial line associated with the port B access both ports (see
the comment at the top of the driver for the details of wiring used).
Please update your scripts.
This is also the reason each SCC now requests an IRQ once only (as seen in
"/proc/interrupts") -- the handler takes care of both ports at once as the
line associated with the port B has to take status update interrupts from
both ports (and yet the line of the port A takes its own for itself too).
The old driver never got it right...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
early_serial_setup was removed from serial.h, but forgot to put in
serial_8250.h
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the SB1250 DUART, a dual serial port implementation
included in the Broadcom family of SOCs descending from the SiByte SB1250
MIPS64 chip multiprocessor. It is a new implementation replacing the
old-fashioned driver currently present in the linux-mips.org tree. It
supports all the usual features one would expect from a(n asynchronous)
serial driver, including modem line control (as far as hardware supports it
-- there is edge detection logic missing from the DCD and RI lines and the
driver does not implement polling of these lines at the moment), the serial
console, BREAK transmission and reception, including the magic SysRq. The
receive FIFO threshold is not maintained though.
The driver was tested with a SWARM board which uses a BCM1250 SOC (which is
dual MIPS64 CMP) and has both ports of the single DUART implemented wired
externally. Both were tested. Testing included using the ports as
terminal lines at 1200bps (which is the ports minimum), 115200bps and a
couple of random speeds inbetween. The modem lines were verified to
operate correctly. No testing was performed with a use as a network
interface, like with SLIP or PPP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (209 commits)
[POWERPC] Create add_rtc() function to enable the RTC CMOS driver
[POWERPC] Add H_ILLAN_ATTRIBUTES hcall number
[POWERPC] xilinxfb: Parameterize xilinxfb platform device registration
[POWERPC] Oprofile support for Power 5++
[POWERPC] Enable arbitary speed tty ioctls and split input/output speed
[POWERPC] Make drivers/char/hvc_console.c:khvcd() static
[POWERPC] Remove dead code for preventing pread() and pwrite() calls
[POWERPC] Remove unnecessary #undef printk from prom.c
[POWERPC] Fix typo in Ebony default DTS
[POWERPC] Check for NULL ppc_md.init_IRQ() before calling
[POWERPC] Remove extra return statement
[POWERPC] pasemi: Don't auto-select CONFIG_EMBEDDED
[POWERPC] pasemi: Rename platform
[POWERPC] arch/powerpc/kernel/sysfs.c: Move NUMA exports
[POWERPC] Add __read_mostly support for powerpc
[POWERPC] Modify sched_clock() to make CONFIG_PRINTK_TIME more sane
[POWERPC] Create a dummy zImage if no valid platform has been selected
[POWERPC] PS3: Bootwrapper support.
[POWERPC] powermac i2c: Use mutex
[POWERPC] Schedule removal of arch/ppc
...
Fixed up conflicts manually in:
Documentation/feature-removal-schedule.txt
arch/powerpc/kernel/pci_32.c
arch/powerpc/kernel/pci_64.c
include/asm-powerpc/pci.h
and asked the powerpc people to double-check the result..
Mixing putchar() and write() hvcalls does not work %100
correctly. But we should be using write() all the time
if we can, even from ->start_tx(), anyways.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (26 commits)
[SPARC64]: Fix UP build.
[SPARC64]: dr-cpu unconfigure support.
[SERIAL]: Fix console write locking in sparc drivers.
[SPARC64]: Give more accurate errors in dr_cpu_configure().
[SPARC64]: Clear cpu_{core,sibling}_map[] in smp_fill_in_sib_core_maps()
[SPARC64]: Fix leak when DR added cpu does not bootup.
[SPARC64]: Add ->set_affinity IRQ handlers.
[SPARC64]: Process dr-cpu events in a kthread instead of workqueue.
[SPARC64]: More sensible udelay implementation.
[SPARC64]: SMP build fixes.
[SPARC64]: mdesc.c needs linux/mm.h
[SPARC64]: Fix build regressions added by dr-cpu changes.
[SPARC64]: Unconditionally register vio_bus_type.
[SPARC64]: Initial LDOM cpu hotplug support.
[SPARC64]: Fix setting of variables in LDOM guest.
[SPARC64]: Fix MD property lifetime bugs.
[SPARC64]: Abstract out mdesc accesses for better MD update handling.
[SPARC64]: Use more mearningful names for IRQ registry.
[SPARC64]: Initial domain-services driver.
[SPARC64]: Export powerd facilities for external entities.
...
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (68 commits)
sh: sh-rtc support for SH7709.
sh: Revert __xdiv64_32 size change.
sh: Update r7785rp defconfig.
sh: Export div symbols for GCC 4.2 and ST GCC.
sh: fix race in parallel out-of-tree build
sh: Kill off dead mach.c for hp6xx.
sh: hd64461.h cleanup and added comments.
sh: Update the alignment when 4K stacks are used.
sh: Add a .bss.page_aligned section for 4K stacks.
sh: Don't let SH-4A clobber SH-4 CFLAGS.
sh: Add parport stub for SuperIO ports.
sh: Drop -Wa,-dsp for DSP tuning.
sh: Update dreamcast defconfig.
fb: pvr2fb: A few more __devinit annotations for PCI.
fb: pvr2fb: Fix up section mismatch warnings.
sh: Select IPR-IRQ for SH7091.
sh: Correct __xdiv64_32/div64_32 return value size.
sh: Fix timer-tmu build for SH-3.
sh: Add cpu and mach links to CLEAN_FILES.
sh: Preliminary support for the SH-X3 CPU.
...
Do not mark sn_sal_console_setup as __init since it's referenced from
non init data structures.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RXBRK field in the AT91/AT32 USART status register has the
following definition according to e.g. the AT32AP7000 data sheet:
RXBRK: Break Received/End of Break
0: No Break received or End of Break detected since the last RSTSTA.
1: Break Received or End of Break detected since the last RSTSTA.
Thus, for each break, the USART sets the RXBRK bit twice. This patch
modifies the driver to report the break event to the serial core only
once by keeping track of whether a break condition is currently
active. The break_active flag is reset as soon as a character is
received, so even if we miss the start-of-break interrupt this should
do the right thing.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ivan Kuten <ivan.kuten@promwad.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@rfo.atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Beacuse SERIAL_PORT_DFNS is removed from include/asm-i386/serial.h and
include/asm-x86_64/serial.h. the serial8250_ports need to be probed late in
serial initializing stage. the console_init=>serial8250_console_init=>
register_console=>serial8250_console_setup will return -ENDEV, and console
ttyS0 can not be enabled at that time. need to wait till uart_add_one_port in
drivers/serial/serial_core.c to call register_console to get console ttyS0.
that is too late.
Make early_uart to use early_param, so uart console can be used earlier. Make
it to be bootconsole with CON_BOOT flag, so can use console handover feature.
and it will switch to corresponding normal serial console automatically.
new command line will be:
console=uart8250,io,0x3f8,9600n8
console=uart8250,mmio,0xff5e0000,115200n8
or
earlycon=uart8250,io,0x3f8,9600n8
earlycon=uart8250,mmio,0xff5e0000,115200n8
it will print in very early stage:
Early serial console at I/O port 0x3f8 (options '9600n8')
console [uart0] enabled
later for console it will print:
console handover: boot [uart0] -> real [ttyS0]
Signed-off-by: <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some RS-232 devices require DTR to be asserted before they can be used. DTR
is normally asserted in uart_startup() when the port is opened. But we don't
actually open serial console ports, so assert DTR when the port is added.
BTW:
earlyprintk and early_uart are hard coded to set DTR/RTS.
rmk says
The only issue I can think of is the possibility for an attached modem to
auto-answer or maybe even auto-dial before the system is ready for it to do
so. Might have an undesirable cost implication for some running with such a
setup.
Apart from that, I can't think of any other side effect of this specific
patch.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mirror the logic in 8250 for proper console write locking
when SYSRQ is triggered or an OOPS is in progress.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Rename PC speaker code
[MIPS] Don't use genrtc.
[MIPS] Remove unused time.c for swarm
[MIPS] Sparse: Use NULL for pointer
[MIPS] Fix a sparse warning in arch/mips/pci/pci.c
[MIPS] SMTC: Interrupt mask backstop hack
[MIPS] separate platform_device registration for VR41xx RTC
[MIPS] Separate platform_device registration for VR41xx GPIO
[MIPS] MIPSsim: Fix build.
[MIPS] separate platform_device registration for VR41xx serial interface
[MIPS] Include cacheflush.h in uncache.c
[MIPS] Cleanup tlbdebug.h
[MIPS] Change names of local variables to silence sparse (part 2)
[MIPS] Workaround for a sparse warning in include/asm-mips/io.h
[MIPS] RM: Use only phyiscal address for 82596 and 53c710
[MIPS] Hydrogen3: Remove remaining bits of code.
[MIPS] DEC: Fix modpost warning.
Revert "[MIPS] DEC: Fix modpost warning."
[MIPS] Fix resume for 64K page size on R4000 class processors.
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, of_serial driver supports only 8250 compatible ports, but
prepares that others can easily be added. Yet unregister routine
assumes port is 8250. This corrects unregister routine to check
port type.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current of_serial driver assumes unknown serial port to be 8250. But
this behavior may cause fatal problems when the serial port is not
8250. This corrects probe routine to ignore unknown serial port.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The interrupt clearing code in mpsc_sdma_intr_ack() mistakenly clears the
interrupt for both controllers instead of just the one its supposed to.
This can result in the other controller appearing to hang because its
interrupt was effectively lost.
So, don't clear the interrupt cause bits for both MPSC controllers when
clearing the interrupt for one of them. Just clear the one that is
supposed to be cleared.
Signed-off-by: Jay Lubomirski <jaylubo@motorola.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
as the termios info does not stipulate that the former are dependent on the latter
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
if we get a break signal, we want to ignore framing and parity errors
because those will always be set (by nature of the signal)
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Now that select no longer works for selecting the "closest" CPU,
we have to explicitly reference the precise sub-type in the few
places where it actually matters (presently only setup code and
some legacy sh-sci cruft).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
