First move of items out of include/asm-arm/plat-s3c* to their
new homes under arch/arm/plat-s3c/include/plat and
arch/arm/plat-s3c24xx/include/plat directories.
Note, we have to create a dummy arch/arm/plat-s3c/Makefile to
allow us to add arch/arm/plat-s3c/include/plat to the path.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This was added at a time when the compiler did a less than stellar job of
optimizing out dead code. These days this tends to be less of a concern,
so kill it all off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is conditionalized on sh, and disabled for sh64.
Now that SH-5 ties in to the clock framework, the sh64 exception
can be dropped. Additionally, ARM will want to use the same hooks
once SH-Mobile G3 grows clock framework support, so switch these
paths over to HAVE_CLK now.
Once the H8 and ARM sh-sci users hook up HAVE_CLK, the driver can
be switched over to having an outright dependency on it and the
ifdefs can go away.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The function ks8695uart_set_termios() would cause an unbalanced
enable_irq() generated message to be printk()ed. This is because
there was no book keeping support to remember if the calls to
enable_irq() and disable_irq() were balanced for the modem
control irq.
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Presently we don't do much with UPF_IOREMAP other than special case it
for SH-5's onchip_remap() on the early console. Tie this in generically
for platforms that need the remap.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore
remove the dead code associated with !CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This problem seems to be unnoticed so far:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=b3b708fa2780cd2b5d8266a8f0c3a1cab364d4d2
has changed the serial core behavior to not to suspend the port if the
device is enabled as a wakeup source. If the AT91 system goes to slow
clock mode, the port should be suspended always and the clocks should be
switched off. The patch attached updates the atmel_serial driver to match
the changes in serial core.
Also, the interrupts are disabled when the clock is disabled. If we
disable the clock with interrupts enabled, an interrupt may get stuck. If
this is the DBGU interrupt, this blocks the OR logic at system controller
and thus all other sysc interrupts.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Michael Trimarchi <trimarchimichael@yahoo.it>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're currently passing NULL, and really shouldn't be.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With the change to device tree based setup we no longer need the explicit
Kconfig options for each SCC{1,4} or SMC{1,2} port.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adds hardware CTSRTS control for pxa serial devices through
termios controls.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A function to contain common code for the size of the resource we
need to allocate or free. OMAP ports need 22 bytes rather than
the standard 8 bytes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make is_omap_port() take the uart_8250_port structure so it can do
whatever test it desires. Convert the test to compare the physical
addresses rather than virtual addresses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recent changes to tighten the check for UARTs that don't correctly
re-assert THRE (01c194d927: "serial 8250:
tighten test for using backup timer") caused problems when such a UART was
opened for the second time - the bug could only successfully be detected
at first initialization. For users of this version of this particular
UART IP it is fatal.
This patch stores the information about the bug in the bugs field of the
port structure when the port is first started up so subsequent opens can
check this bit even if the test for the bug fails.
David Brownell: "My own exposure to this is that the UART on DaVinci
hardware, which TI allegedly derived from its original 16550 logic, has
periodically gone from working to unusable with the mainline 8250.c ...
and back and forth a bunch. Currently it's "unusable", a regression from
some previous versions. With this patch from Will, it's usable."
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alex Williamson <alex.williamson@hp.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interrupt handler for muxed interrupts (imx2/imx3) was calling
the rts handling subroutine if the RTSS bit was set.
(Which indicates the status of the RTS line), leading to an
interrupt flood on RTS bit low.
This patch fixes the problem by looking at the RTSD bit instead,
indicating a change in the RTS line.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
RX in i.MX27 and i.MX31 UART lines does not work unless the
"RXD Muxed Input Select" bit is set on i.MX27 and i.MX31 processors.
This patch sets the missing RXD mux bit in the UCR3 register.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adds extra "out" label to probe function after calling .init form platform data.
Because .init can return error number caused by gpio request fail.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we're just parsing the tuple being passed to this function, we don't
need any device-specific information.
Also, remove the call to pcmcia_validate_cis() from pcmciamtd.c, since it
is already called by the PCMCIA core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
CS_NO_MORE_ITEMS is returned by the CIS tuple reading and parsing code if
the end of a tuple chain is reached. As at least one PCMCIA driver relies
on matching this return value, replace it with -ENOSPC which is now
uniquely used for this purpose within the in-kernel pcmcia subsystem.
CC: Russell King <rmk+kernel@arm.linux.org.uk>
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of using own error or success codes, the PCMCIA code should rely on
the generic return values. Therefore, replace all occurrences of CS_SUCCESS
with 0.
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove the three remaining pcmcia_get_configuration_info() users:
- pcmciamtd is marked broken anyway.
- serial_cs.c can access the relevant structs directly
- ipwireless didn't use the output
CC: linux-serial@vger.kernel.org
CC: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
By passing the current Vcc setting to the pcmcia_config_loop callback
function, we can remove pcmcia_get_configuration_info() calls from many
drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many drivers use the default CIS entry within their pcmcia_config_loop()
callback function. Therefore, factor the default CIS entry handling out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Almost all drivers set p_dev->conf.ConfigIndex to cfg->index in
the pcmcia_config_loop() callback function. Therefore, factor it out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use the config loop helper in misc pcmcia drivers.
CC: Harald Welte <laforge@gnumonks.org>
CC: <linux-parport@lists.infradead.org>
CC: Russell King <rmk+kernel@arm.linux.org.uk>
CC: Ed Okerson <eokerson@quicknet.net>
CC: linux-serial@vger.kernel.org
CC: boti@rocketmail.com
CC: linux-usb@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Handle stack trace attempts before irqstacks are setup.
sparc64: Implement IRQ stacks.
sparc: remove include of linux/of_device.h from asm/of_device.h
sparc64: Fix recursion in stack overflow detection handling.
sparc/drivers: use linux/of_device.h instead of asm/of_device.h
sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It now compiles with the tty changes but isn't tested (which has to be
better than not compiling..
Closes bug #11218
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blackfin peers into the ldisc in an odd way for IRDA snooping which
therefore got missed. Simple enough fix.
Closes bug #11233
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (28 commits)
mm/hugetlb.c must #include <asm/io.h>
video: Fix up hp6xx driver build regressions.
sh: defconfig updates.
sh: Kill off stray mach-rsk7203 reference.
serial: sh-sci: Fix up SH7760/SH7780/SH7785 early printk regression.
sh: Move out individual boards without mach groups.
sh: Make sure AT_SYSINFO_EHDR is exposed to userspace in asm/auxvec.h.
sh: Allow SH-3 and SH-5 to use common headers.
sh: Provide common CPU headers, prune the SH-2 and SH-2A directories.
sh/maple: clean maple bus code
sh: More header path fixups for mach dir refactoring.
sh: Move out the solution engine headers to arch/sh/include/mach-se/
sh: I2C fix for AP325RXA and Migo-R
sh: Shuffle the board directories in to mach groups.
sh: dma-sh: Fix up dreamcast dma.h mach path.
sh: Switch KBUILD_DEFCONFIG to shx3_defconfig.
sh: Add ARCH_DEFCONFIG entries for sh and sh64.
sh: Fix compile error of Solution Engine
sh: Proper __put_user_asm() size mismatch fix.
sh: Stub in a dummy ENTRY_OFFSET for uImage offset calculation.
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
The removal of drivers/serial/v850e_uart.c originally was in my v850
removal patch, but it seems it got lost somewhere.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
serial8250_startup() doesn't disable interrupts while taking the &up->port.lock
which might race against the interrupt handler serial8250_interrupt(), which
when entered, will deadlock waiting for the lock to be released.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As noted by Manuel:
Commit c63847a362 ("sh: Add
SCIF2 support for SH7763.") broke build with CONFIG_EARLY_PRINTK
enabled for me (SH7760):
CC arch/sh/kernel/early_printk.o
/mnt/work/sh7760/kernel/linux-2.6.git/arch/sh/kernel/early_printk.c: In function 'scif_sercon_putc':
/mnt/work/sh7760/kernel/linux-2.6.git/arch/sh/kernel/early_printk.c:84: error: implicit declaration of function 'sci_SCFDR_in'
Move the SH7763 definitions out on their own, so they don't create additional
confusion within the SH7760/SH7780/SH7785 block. Restore the deleted
SCFDR definition for these parts.
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch introduces baudrate setting support via the generic clock API.
When present the optional device tree clock property is used instead of
fsl-cpm-brg. Platforms can then define complex clock schemes, to output
the serial clock on an external pin for instance.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch replaces the get_mctrl/set_mctrl stubs with modem control line
read/write access through the GPIO lib.
Available modem control lines are described in the device tree using GPIO
bindings. The driver expect a GPIO pin for each of the CTS, RTS, DCD, DSR,
DTR and RI signals. Unused control lines can be left out.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Before setting STOP_TX, set _brkcr to 0 so the SMC does not send a break
character. The driver appears to properly re-initialize _brkcr when the
SMC is restarted.
Do not interrupt RX/TX when the termios is being adjusted; it results in
corrupted characters appearing on the line.
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes to the generic console support code that happened a while ago
introduced a scenario where the initial console is used in parallel with
the final console during a brief period when switching between the two is
in progress. During that time a message about the switch-over is printed.
With some combinations of chips, firmware and drivers, such as the DEC
DZ11 clone used with the DECstation, a hang may happen because the
firmware used for the initial console may not expect the state of the chip
after it has been initialised by the driver.
This is a workaround for the DZ11 which reuses the power-management
callback to keep the transmitter of the line associated with the console
enabled. It reflects the consensus reached in a discussion a while ago.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes to the generic console support code that happened a while ago
introduced a scenario where the initial console is used in parallel with
the final console during a brief period when switching between the two is
in progress. During that time a message about the switch-over is printed.
With some combinations of chips, firmware and drivers, such as the Zilog
Z85C30 SCC used with the DECstation, a hang may happen because the
firmware used for the initial console may not expect the state of the chip
after it has been initialised by the driver. This is not a bug in the
firmware, as some registers it would have to examine are write-only.
This is a workaround for the Z85C30 which reuses the power-management
callback to keep the transmitter of the line associated with the console
enabled. It reflects the consensus reached in a discussion a while ago.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is a no-name PCI card. I found no reference to a producer so I used
"UNKNOWN_0x1584" as the name.
Full lspci:
01:07.0 0780: 10b5:9050 (rev 01)
Subsystem: 10b5:1584
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- \
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- \
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 1: I/O ports at ec00 [size=128]
Region 2: I/O ports at e480 [size=32]
Region 3: I/O ports at e400 [size=8]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA \
PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] #06 [0080]
Capabilities: [4c] Vital Product Data
After:
0000:01:07.0: ttyS4 at I/O 0xe480 (irq = 10) is a 16550A
0000:01:07.0: ttyS5 at I/O 0xe488 (irq = 10) is a 16550A
0000:01:07.0: ttyS6 at I/O 0xe490 (irq = 10) is a 16550A
0000:01:07.0: ttyS7 at I/O 0xe498 (irq = 10) is a 16550A
Signed-off-by: Catalin(ux) M BOIE <catab@embedromix.ro>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel 82571 has a "Serial Over LAN" feature that doesn't properly
implements the receiving of break characters. When a break is received,
it doesn't set UART_LSR_DR and unless another character is received, the
break won't be received by the application.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the missing MODULE_LICENSE("GPL").
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trying to compile the v850 port brings many compile errors, one of them exists
since at least kernel 2.6.19.
There also seems to be noone willing to bring this port back into a usable
state.
This patch therefore removes the v850 port.
If anyone ever decides to revive the v850 port the code will still be
available from older kernels, and it wouldn't be impossible for the port to
reenter the kernel if it would become actively maintained again.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add in console polling hooks for the cpm uart for use with kgdb and
kgdboc.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: galak@kernel.crashing.org
I missed the cpm_uart one. Thanks to Kumar Gala for reporting it. A double
check found samsung also needed fixing up.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With SMP kernels _irqsave spinlock disables only local interrupts, while
the shared serial interrupt could be assigned to the CPU that is not
currently starting up the serial port.
This might cause issues because serial8250_startup() routine issues
IRQ-triggering operations before registering the port in the IRQ chain
(though, this is fine to do and done explicitly because we don't want to
process any interrupts on the port startup).
With RT kernels and preemptable hardirqs, _irqsave spinlock does not
disable local hardirqs, and the bug could be reproduced much easily:
$ cat /dev/ttyS0 &
$ cat /dev/ttyS1
irq 42: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[C0475EB0] [C0008A98] show_stack+0x4c/0x1ac (unreliable)
[C0475EF0] [C004BBD4] __report_bad_irq+0x34/0xb8
[C0475F10] [C004BD38] note_interrupt+0xe0/0x308
[C0475F50] [C004B09C] thread_simple_irq+0xdc/0x104
[C0475F70] [C004B3FC] do_irqd+0x338/0x3c8
[C0475FC0] [C00398E0] kthread+0xf8/0x100
[C0475FF0] [C0011FE0] original_kernel_thread+0x44/0x60
handlers:
[<c02112c4>] (serial8250_interrupt+0x0/0x138)
Disabling IRQ #42
After this, all serial ports on the given IRQ are non-functional.
To fix the issue we should explicitly disable shared IRQ before
issuing any IRQ-triggering operations.
I also changed spin_lock_irqsave to the ordinary spin_lock, since it
seems to be safe: chain does not contain new port (yet), thus nobody
will interfere us from the ISRs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some hardware needs to do break handling itself and may have partial
support only. Make break_ctl return an error code. Add a tty driver flag
so you can indicate driver hardware side break support.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty pointer has been moved into a tty_port field, so we need to use
->info->port.tty instead of just ->info->tty. Fixes these build errors:
David Brownell <david-b@pacbell.net> wrote:
> drivers/serial/atmel_serial.c: In function 'atmel_rx_from_ring':
> drivers/serial/atmel_serial.c:665: error: 'struct uart_info' has no member named 'tty'
> drivers/serial/atmel_serial.c: In function 'atmel_rx_from_dma':
> drivers/serial/atmel_serial.c:672: error: 'struct uart_info' has no member named 'tty'
> drivers/serial/atmel_serial.c: In function 'atmel_startup':
> drivers/serial/atmel_serial.c:797: error: 'struct uart_info' has no member named 'tty'
> make[2]: *** [drivers/serial/atmel_serial.o] Error 1
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The below is the patch to replace blindly all possible places,
including Jack's fixes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
(Reviewed and checked rather than blindly added)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix compile errors in SGI console drivers caused by changes to the
tty_port structures in the linux-next tree.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's linux-next build (powerpc allyesconfig) failed like this:
drivers/serial/pmac_zilog.c: In function 'pmz_receive_chars':
drivers/serial/pmac_zilog.c:245: error: 'struct uart_info' has no member named 'tty'
drivers/serial/pmac_zilog.c:250: error: 'struct uart_info' has no member named 'tty'
I applied the patch below (which builds but may, or may not, be correct).
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.auhttp://www.canb.auug.org.au/~sfr/
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's linux-next build (sparc64 defconfig) failed like this:
drivers/serial/sunhv.c: In function `receive_chars':
drivers/serial/sunhv.c:188: error: structure has no member named `tty'
drivers/serial/sunsu.c: In function `receive_chars':
drivers/serial/sunsu.c:314: error: structure has no member named `tty'
drivers/serial/sunsab.c: In function `receive_chars':
drivers/serial/sunsab.c:121: error: structure has no member named `tty'
I applied the following patch (which, again, may not be correct).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the serial_core based drivers to use the new tty_port structure.
We can't quite use all of it yet because of the dynamically allocated
extras in the serial_core layer.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes CVS keywords that weren't updated for a long time in
comments, printk's and MODULE_DESCRIPTION's (no printk's or
MODULE_DESCRIPTION's are completely removed).
While doing this I also found and fixed a missing \n in a printk
in m32r_sio.c
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid dumping garbage to the serial port when the tty is flushed. This
tends to happen when rebooting from a serial console.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serial drivers using DMA (like the atmel_serial driver) tend to get very
confused when the xmit buffer is flushed and nobody told them. They
also tend to spew a lot of garbage since the DMA engine keeps running
after the buffer is flushed and possibly refilled with unrelated data.
This patch adds a new flush_buffer operation to the uart_ops struct,
along with a call to it from uart_flush_buffer() right after the xmit
buffer has been cleared. The driver can implement this in order to
syncronize its internal DMA state with the xmit buffer when the buffer
is flushed.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As part of a heuristic to identify modem devices, 8250_pnp.c
checks to see whether a device can be configured at any of the
legacy COM port addresses.
This patch moves the code that traverses the PNP "possible resource
options" from 8250_pnp.c to the PNP subsystem. This encapsulation
is important because a future patch will change the implementation
of those resource options.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The SERIAL_SAMSUNG needs SERIAL_CORE but doesn't select it, leading to a
build failure. Adding a 'select SERIAL_CORE' cure the trouble.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: (31 commits)
avr32: Fix typo of IFSR in a comment in the PIO header file
avr32: Power Management support ("standby" and "mem" modes)
avr32: Add system device for the internal interrupt controller (intc)
avr32: Add simple SRAM allocator
avr32: Enable SDRAMC clock at startup
rtc-at32ap700x: Enable wakeup
macb: Basic suspend/resume support
atmel_serial: Drain console TX shifter before suspending
atmel_serial: Fix build on avr32 with CONFIG_PM enabled
avr32: Use a quicklist for PTE allocation as well
avr32: Use a quicklist for PGD allocation
avr32: Cover the kernel page tables in the user PGDs
avr32: Store virtual addresses in the PGD
avr32: Remove useless zeroing of swapper_pg_dir at startup
avr32: Clean up and optimize the TLB operations
avr32: Rename at32ap.c -> pdc.c
avr32: Move setup_platform() into chip-specific file
avr32: Kill special exception handler sections
avr32: Kill unneeded #include <asm/pgalloc.h> from asm/mmu_context.h
avr32: Clean up time.c #includes
...
Set port->fifosize to the software FIFO size, and update the port timeout
when the baud rate is modified. SCC ports have an optional 32 byte hardware
FIFO which is currently not taken into account, as there is no documented way
to check when the FIFO becomes empty.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix CPM serial port corruption when running with CONFIG_PREEMPT_RT.
Userland usage of console, and kernel printf's were stepping on each others toes.
Also only take lock if not in an oops.
Signed-off-by: Rune Torgersen <runet@innovsys.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I had 8250.nr_uarts=16 in the boot line of a test kernel and I had a weird
mysterious crash in sysfs. After taking an in-depth look I realized that
CONFIG_SERIAL_8250_NR_UARTS was set to 4 and I was walking off the end of
the serial8250_ports array.
Ouch!!!
Don't let this happen to someone else.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the statically initialized tables from the i.MX serial
driver and makes the driver fully dependent on the information provided by
the platform_device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We assumed a 16MHz reference frequency for the UART. While this
is true for i.MX1 most of the time it is not true for MX27/MX31.
Also, add handling for the ONEMS register which is present on
newer versions of the chip and pass a sane minimum baudrate to
uart_get_baud_rate().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As reported by Vipul Gandhi, the current serial_match_port() doesn't work
for tty-devices using dynamic major number allocation. Fix it.
It oopses if you suspend a serial port with _dynamic_ major number. ATM,
I think, there's only the drivers/serial/jsm/jsm_driver.c driver, that
does it in-tree.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Vipul Gandhi <vcgandhi1@aol.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The S3C2410 serial driver in drivers/serial/s3c2410.c has been
growing bigger with the addition of more variants of this hardware
with the growing Samsung SoCs range. As such, it would be
easier to split this code up into a core and per-cpu drivers to
make driver addition easier, and the core smaller.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add attribute to show the current clock source for the serial
driver and remove old and annoying debug output.
Note, this only currently shows the current source with a
"* " prefix to indicate that it is the current source. Future
code will list all the clock sources, with the non-selected
one with " " prefix.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
PATCH FOLLOWS
KernelVersion: 2.6.26-rc3
The original driver had an MODULE_LICENSE statement for GPL,
but no explict license in the header of the file. To make
this more explicit, and since I am the original authour,
we will add a GPLv2 header.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the changelog which should really be found
in the version control system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Funny things may happen if we stop the USART clock before the shifter is
empty. Prevent this from happening by waiting until the shifter is
completely drained before allowing suspend to continue.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
AVR32 doesn't have at91_suspend_entering_slow_clock(). Just assume the
clock will keep running for now.
David has a better solution for this, but this works for now. Leaving
the USART clock running won't prevent the PM code from entering deep
power-down modes anyway.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Now that arch/ppc is gone we always define CONFIG_PPC_CPM_NEW_BINDING so
we can remove all the code associated with !CONFIG_PPC_CPM_NEW_BINDING.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This allows other threads to run when the serial driver polls the CTS
PIN in a loop.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
This is the patch that follows Linus's modification about set_ldisc.
Graf has built and tested it on BF537 using Linus's git Tree.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
I made a change to u-boot that used the FP (Fractional Part) field of BRGR
to achieve more accurate baud rate generation. Unfortunately, the
atmel_serial driver looks at the whole BRGR register when trying to detect
the baud rate that the port is currently running at, so setting FP to a
nonzero value breaks the baud rate detection.
I'll sit on the u-boot patch for a while longer, but this is clearly a
bug in the atmel_serial driver which should be fixed.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers are using too generic "serial" name for driver_name, this
might cause issues, like this:
Freescale QUICC Engine UART device driver
proc_dir_entry 'serial' already registered
Call Trace:
[cf82de50] [c0007f7c] show_stack+0x4c/0x1ac (unreliable)
[cf82de90] [c00b03fc] proc_register+0xfc/0x1ac
[cf82dec0] [c00b05c8] create_proc_entry+0x60/0xac
[cf82dee0] [c00b23dc] proc_tty_register_driver+0x60/0x98
[cf82def0] [c016dbd8] tty_register_driver+0x1b4/0x228
[cf82df20] [c0184d70] uart_register_driver+0x144/0x194
[cf82df40] [c030a378] ucc_uart_init+0x2c/0x94
[cf82df50] [c02f21a0] kernel_init+0x98/0x27c
[cf82dff0] [c000fa74] kernel_thread+0x44/0x60
^^ The board is using ucc_uart.c and 8250.c, both registered as
"serial".
This patch fixes two drivers that are using "serial" for driver_name and
not "ttyS" for dev_name. Drivers that are using "ttyS" for dev_name, will
conflict anyway, so we don't bother with these.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-By: Timur Tabi <timur@freescale.com>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 64e9159f5d ("serial_core:
uart_set_ldisc infrastructure") introduced the ability for low-level
serial drivers to be informed when the tty ldisc changes.
However, the actual tty-layer function that does this callback for
serial devices was declared with the wrong type, having a spurious and
unused 'ldisc' argument.
This fixed the resulting compiler warning by just removing it.
Acked-by: Blithering Idiot <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty layer provides a callback that is used when the line discipline
is changed. Some hardware uses this to configure hardware specific
features such as IrDA mode on serial ports. Unfortunately the serial
layer does not provide this feature or pass it down to drivers.
Blackfin used to hack around this by rewriting the tty ops, but those are
now properly shared and const so the hack fails. Instead provide the
proper operations.
This change plus a follow up from the Blackfin guys is needed to avoid
blackfin losing features in this release.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Russell pointed out, original patch will break some serial configurations
because of the dependency of the <asm/serial.h> header file.
Revert it first and try to find out other solution later
Cc: Javier Herrero <jherrero@hvsistemas.es>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
enable_irq_wake() and disable_irq_wake() need to be balanced. However,
serial_core.c calls these for different conditions during the suspend and
resume functions...
This is causing a regular WARN_ON() as found at
http://www.kerneloops.org/search.php?search=set_irq_wake
This patch makes the conditions for triggering the _wake enable/disable
sequence identical.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the InstaShield IS-400 four port RS-232 PCI card.
Signed-off-by: Ignacio García Pérez <iggarpe@t2i.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin SPORTS UART Driver: converting BFIN->BLACKFIN
Blackfin serial driver: add extra IRQ flag for 8250 serial driver
8250 Serial Driver: Added support for 8250-class UARTs in HV Sistemas H8606 board
Blackfin arch: Fix bug - USB fails to build for BF524/BF526
Blackfin arch: update boards defconfig files
Blackfin arch: IO Port functions to read/write unalligned memory
Blackfin arch: enable a choice to provide 4M DMA memory
Blackfin arch: cleanup the icplb/dcplb multiple hit checks
Blackfin arch: Add workaround to read edge triggered GPIOs
Blackfin arch: Sync channel defines with struct dma_register dma_io_base_addr.
Blackfin arch: Check for Anomaly 05000182
[Blackfin] arch: rename bf5xx-flash to bfin-async-flash
[Blackfin] arch: Blackfin checksum annotations
Added support for 8250-class UARTs in HV Sistemas H8606 board,
modification in 8250.c driver for correct compilation with Blackfin
Besides, I think that there is more people using 8250-class UARTs
with a different hardware than the H8606 board. This code can be shared
by them.
Signed-off-by: Javier Herrero <jherrero@hvsistemas.es>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Schedule a removal for this driver. Alternative driver is available for
a while now.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (21 commits)
Blackfin Serial Driver: abstract away DLAB differences into header
Blackfin Serial Driver: macro away the IER differences between processors
[Blackfin] arch: remove useless IRQ_SW_INT defines
[Blackfin] arch: protect linux/usb/musb.h include until the driver gets mainlined
[Blackfin] arch: protect linux/usb/isp1362.h include until the driver gets mainlined
[Blackfin] arch: add EBIU supporting for BF54x EZKIT SMSC LAN911x/LAN921x families embedded ethernet driver
[Blackfin] arch: Set spi flash partition on bf527 as like bf548.
[Blackfin] arch: fix bug - Remove module will not free L1 memory used
[Blackfin] arch: fix wrong header name in comment
[Blackfin] arch: Fix BUG - spi flash on bf527 ezkit would fail at mount
[Blackfin] arch: add twi_lcd and twi_keypad i2c board info to bf527-ezkit
[Blackfin] arch: Add physmap partition for BF527-EZkit
[Blackfin] arch: fix gdb testing regression
[Blackfin] arch: disable single stepping when delivering a signal
[Blackfin] arch: Delete unused (copied from m68k) entries in asm-offsets.c.
[Blackfin] arch: In the double fault handler, set up the PT_RETI slot
[Blackfin] arch: Support for CPU_FREQ and NOHZ
[Blackfin] arch: Functional power management support: Add CPU and platform voltage scaling support
[Blackfin] arch: fix bug - breaking the atomic sections code.
[Blackfin] arch: Equalize include files: Add VR_CTL masks
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (37 commits)
SH: catch negative denormal_subf1() retval in denormal_add()
sh: Fix DMAC base address for SH7709S
sh: update smc91x platform data for se7206.
sh: Stub in cpu_to_node() and friends for NUMA build.
sh: intc register modify fix
sh: no high level trigger on some sh3 cpus
sh: clean up sh7710 and sh7720 intc tables
sh: add interrupt ack code to sh3
sh: unify external irq pin code for sh3
sh-sci: avoid writing to nonexistent registers
sh-sci: sh7722 lacks scsptr registers
sh-sci: improve sh7722 support
sh: reset hardware from early printk
sh: drain and wait for early printk
sh: use sci_out() for early printk
sh: add memory resources to /proc/iomem
sh: add kernel bss resource
sh: fix sh7705 interrupt vector typo
sh: update smc91x platform data for se7722
sh: update smc91x platform data for MigoR
...
I noticed that
static void uart_flush_buffer(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
struct uart_port *port = state->port;
unsigned long flags;
/*
* This means you called this function _after_ the port was
* closed. No cookie for you.
*/
if (!state || !state->info) {
WARN_ON(1);
return;
}
is too late for checking state != NULL.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only write to hardware in SCI_OUT() if the register size is valid.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh7722 serial ports all lack SCSPTR registers, so mark them as
nonexistent in the register table.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve sh7722 support for SCIF1 and SCIF2 and separate code
from sh7366 implementation.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
mpc52xx_uart_int and __uart_put_char both try to acquire the
port->lock. Therefore the function sequence of:
mpc52xx_uart_int--> ...-->flush_to_ldisc-->...-->__uart_put_char
can potentially trigger a deadlock. To avoid this deadlock a fix
similar to that found in the 8250.c serial driver is applied. The
deadlock is avoided by releasing the lock before pushing a buffer
and reacquiring it when completed.
Signed-off-by: Andrew Liu <shengping.liu@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add new PCI Express Neo/JSM board to the supported list of drivers in
the JSM driver.
Signed-off-by: Scott Kilau <scottk@digi.com>
Acked-by: Ananda V <avenkat@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Operations are now a shared const function block as with most other Linux
objects
- Introduce wrappers for some optional functions to get consistent behaviour
- Wrap put_char which used to be patched by the tty layer
- Document which functions are needed/optional
- Make put_char report success/fail
- Cache the driver->ops pointer in the tty as tty->ops
- Remove various surplus lock calls we no longer need
- Remove proc_write method as noted by Alexey Dobriyan
- Introduce some missing sanity checks where certain driver/ldisc
combinations would oops as they didn't check needed methods were present
[akpm@linux-foundation.org: fix fs/compat_ioctl.c build]
[akpm@linux-foundation.org: fix isicom]
[akpm@linux-foundation.org: fix arch/ia64/hp/sim/simserial.c build]
[akpm@linux-foundation.org: fix kgdb]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Stop drivers calling their own flush method indirectly, it obfuscates code
and it will change soon anyway
- A few more lock_kernel paths temporarily needed in some driver internal
waiting code
- Remove private put_char method that does a write call for one char - we
have that anyway
- Most but not yet all of the termios copy under lock fixing (some has other
dependencies to follow)
- Note a few locking bugs in drivers found in the process
- Kill remaining [ab]users of TIOCG/SSOFTCAR in the driver, these must go to
fix the termios locking
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of checking for the BKL in these methods, take it ourselves. That
avoids propogating it into the serial drivers and we can then fix them later
on.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Noticed while auditing the code for the BKL elimination project
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If CONFIG_PPC_MPC5121 is not set, then the of_device_id table for the
mpc5200 serial driver will not get terminated with a NULL entry.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
port->irq is unsigned, platform_get_irq() may return signed unnoticed
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the code registering the Alchemy UART platform devices from
drivers/serial/ to its proper place, into the Alchemy platform code. Fix
the related Kconfig entry, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the semantic patch making this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@ change_compare_np @
expression E;
@@
(
- jiffies <= E
+ time_before_eq(jiffies,E)
|
- jiffies >= E
+ time_after_eq(jiffies,E)
|
- jiffies < E
+ time_before(jiffies,E)
|
- jiffies > E
+ time_after(jiffies,E)
)
@ include depends on change_compare_np @
@@
#include <linux/jiffies.h>
@ no_include depends on !include && change_compare_np @
@@
#include <linux/...>
+ #include <linux/jiffies.h>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Koeller had reported an issue where a device that had been making use
of the UART_BUG_TXEN code in the 8250 driver was mistakenly being caught by
the backup timer test, causing the device to work improperly.
To fix this, tighten the test requirements to enable the backup timer
workaround.
The backup timer is really meant to catch UARTs that don't re-assert the THRE
interrupt. The expectation is that they do initially assert THRE. This patch
clarifies the test.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Cc: Thomas Koeller <thomas@koeller.dyndns.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russell King noticed this one: We have to avoid replacing B0 when we pick a
baud rate for a "hung up" port. Ugly but the proper fix is in the tty layer
and means changing the tty<->serial interfaces so we will defer that for now.
[akpm@linux-foundation.org: fix uninitialised var]
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We try and write the correct speed back but the serial midlayer already
mangles the speed on us and that means if we request B0 we report back B9600
when we should not. For now we'll hack around this in the drivers and serial
code, pending a better long term solution.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings:
WARNING: drivers/serial/built-in.o(.data+0x5b8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_ite887x_exit()
WARNING: drivers/serial/built-in.o(.data+0x5e0): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x608): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x658): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x680): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x6a8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x6d0): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x6f8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x720): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x748): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
pci_serial_quirks contains a number of function pointers where the referenced
function is annotated __devexit. This is OK so we annotate pci_serial_quirks
with __refdata to ignore the __devexit references
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just the modem bits this time
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When loops reaches 0 the postfix decrement still subtracts, so the subsequent
test fails.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Johannes Weiner <hannes@saeurebad.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (49 commits)
[POWERPC] Add zImage.iseries to arch/powerpc/boot/.gitignore
[POWERPC] bootwrapper: fix build error on virtex405-head.S
[POWERPC] 4xx: Fix 460GT support to not enable FPU
[POWERPC] 4xx: Add NOR FLASH entries to Canyonlands and Glacier dts
[POWERPC] Xilinx: of_serial support for Xilinx uart 16550.
[POWERPC] Xilinx: boot support for Xilinx uart 16550.
[POWERPC] celleb: Add support for PCI Express
[POWERPC] celleb: Move miscellaneous files for Beat
[POWERPC] celleb: Move a file for SPU on Beat
[POWERPC] celleb: Move files for Beat mmu and iommu
[POWERPC] celleb: Move files for Beat hvcall interfaces
[POWERPC] celleb: Move the SCC related code for celleb
[POWERPC] celleb: Move the files for celleb base support
[POWERPC] celleb: Consolidate io-workarounds code
[POWERPC] cell: Generalize io-workarounds code
[POWERPC] Add CONFIG_PPC_PSERIES_DEBUG to enable debugging for platforms/pseries
[POWERPC] Convert from DBG() to pr_debug() in platforms/pseries/
[POWERPC] Register udbg console early on pseries LPAR
[POWERPC] Mark udbg console as CON_ANYTIME, ie. callable early in boot
[POWERPC] Set udbg_console index to 0
...
The Xilinx 16550 uart core is not a standard 16550 because it uses
word-based addressing rather than byte-based addressing. With
additional properties it is compatible with the open firmware
'ns16550' compatible binding.
This code updates the of_serial driver to handle the reg-offset
and reg-shift properties to enable this core to be used.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (85 commits)
Blackfin char driver for Blackfin on-chip OTP memory (v3)
Blackfin Serial Driver: fix bug - use mod_timer to replace only add_timer.
Blackfin Serial Driver: the uart break anomaly has been given its own number, so switch to it
Blackfin Serial Driver: use BFIN_UART_NR_PORTS to help SIR driver in uart port.
Blackfin Serial Driver: Fix bug - kernel hangs when accessing uart 0 on bf537 when booting u-boot and linux on uart 1
Blackfin Serial Driver: punt unused lsr variable
Blackfin Serial Driver: Enable IR function when user application (irattach /dev/ttyBFx -s) call TIOCSETD ioctl with line discipline N_IRDA
[Blackfin] arch: add include/boot .gitignore files
[Blackfin] arch: Functional power management support: Add support for cpu frequency scaling
[Blackfin] arch: Functional power management support: Remove broken cpu frequency scaling drivers
[Blackfin] arch: Equalize include files: Add PLL_DIV Masks
[Blackfin] arch: Add a warning about the value of CLKIN.
[Blackfin] arch: take DDR DEVWD into consideration as well for BF548
[Blackfin] arch: Remove the circular buffering mechanism for exceptions
[Blackfin] arch: lose unnecessary dependency on CONFIG_BFIN_ICACHE for MPU
[Blackfin] arch: fix bug - before assign new channel to the map register, need clear the bits first.
[Blackfin] arch: add Blackfin on-chip SIR IrDA driver support
[Blackfin] arch: BF54x memsizes are in mbits, not mbytes
[Blackfin] arch: try to remove condition that causes double fault, by checking current before it gets dereferenced
[Blackfin] arch: Update anomaly list.
...
I have a sparcstation 20 clone with a lot of on board serial ports.
The serial core code assumes that uarts are assigned contiguously
and that may not be the case when there are multiple zs devices
present. This patch insures that uart chips are placed in front of
keyboard/mouse chips in the port table.
ffd37420: ttyS0 at MMIO 0xf1100000 (irq = 44) is a zs (ESCC)
Console: ttyS0 (SunZilog zs0)
console [ttyS0] enabled
ffd37420: ttyS1 at MMIO 0xf1100004 (irq = 44) is a zs (ESCC)
ffd37500: Keyboard at MMIO 0xf1000000 (irq = 44) is a zs
ffd37500: Mouse at MMIO 0xf1000004 (irq = 44) is a zs
ffd3c5c0: ttyS2 at MMIO 0xf1100008 (irq = 44) is a zs (ESCC)
ffd3c5c0: ttyS3 at MMIO 0xf110000c (irq = 44) is a zs (ESCC)
ffd3c6a0: ttyS4 at MMIO 0xf1100010 (irq = 44) is a zs (ESCC)
ffd3c6a0: ttyS5 at MMIO 0xf1100014 (irq = 44) is a zs (ESCC)
ffd3c780: ttyS6 at MMIO 0xf1100018 (irq = 44) is a zs (ESCC)
ffd3c780: ttyS7 at MMIO 0xf110001c (irq = 44) is a zs (ESCC)
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
This patch (as1059) fixes a mistake in the way the serial core
initializes a device's wakeup settings. It should use the accessor
routine instead of relying on a macro producing an lvalue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Implement the serial polling hooks for the pl011 uart for use with
kgdboc.
This patch was specifically tested on the ARM Versatile AB reference
platform.
[ mingo@elte.hu: minor cleanups. ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the run time configuration of kgdboc such that it does not default
to 9600 baud if you use the "echo" command to configure the sysfs
module paramater.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
polled console handling support, to access a console in an irq-less
way while in debug or irq context.
absolutely zero impact as long as CONFIG_CONSOLE_POLL is disabled.
(which is the default)
[ jan.kiszka@siemens.com: lots of cleanups ]
[ mingo@elte.hu: redesign, splitups, cleanups. ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
The membase field in struct uart_port should be the the physical
address. This patch fixes it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not use hardcoded io space size. Instead use the information provided
by the resource.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We are not interested in tranceiver empty interrupts until we actually
sent a buffer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not use the URXD_CHARRDY bit for polling for new characters. This works
on i.MX1, but on MX31 the datasheet states that this bit should not be
used for polling. On MX27 it is even worse, here we get a bus error when
we access the read FIFO when no character is present.
Instead, use USR2_RDR (receive data ready) bit.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the error handling code for erroneous receive characters into
execution path. This makes the code more readable and the compiler
should know how to optimize this, right?
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the unused defines NR_PORTS and IMX_ISR_PASS_LIMIT in
the imx serial driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- get rid of `model = "UCC"' in the ucc nodes
It isn't used anywhere, so remove it. If we'll ever need something
like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
Drivers are modified for backward compatibility's sake.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch allocates parameter RAM for SMC serial ports without relying on
previous initialisation by a boot loader or a wrapper layer.
SMC parameter RAM on CPM2-based platforms can be allocated anywhere in the
general-purpose areas of the dual-port RAM. The current code relies on the
boot loader to allocate a section of general-purpose CPM RAM and gets the
section address from the device tree.
This patch modifies the device tree address usage to reference the SMC
parameter RAM base pointer instead of a pre-allocated RAM section and
allocates memory from the CPM dual-port RAM when initialising the SMC port.
CPM1-based platforms are not affected.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable serial
platform drivers, to re-enable auto loading.
NOTE that Kconfig for some of these drivers doesn't allow modular builds, and
thus doesn't match the driver source's unload support. Presumably their
unload code is buggy and/or weakly tested...
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The of_serial driver queries the current-speed property and attempts
to use it to register the custom_divisor property of the uart_port.
However, if current-speed is not set, then this code will dereference
a bad pointer. The fix is to only set custom_divisor when a
current-speed property appears in the device tree.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Strange chars appear on the serial port when a printk and a printf
happens at the same time. This is caused by the pdc sending chars while
atmel_console_write (called from printk) is executing
Concurent access of uart and console to the same port leads to corrupted
data to be transmitted, so disable tx dma (PDC) while writing to the
console.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found a problem related to losing data during pdc transmission in
atmel_serial: connect ttyS1 with ttyS2 using a loopback cable, send 30
byte of packet from one to the other and waiting for 30 byte. On the
other side just read and echo the data received.
We always call atmel_tx_dma() from the tasklet regardless of what interrupt
triggered it.
Signed-off-by: michael <trimarchi@gandalf.sssup.it>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was an off-by-1 in the SCRFDR calculation that caused writes over
128-bytes to hang in the FIFO. Fix it up.
Signed-off-by: Yutaro Ebihara <ebiharaml@si-linux.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the following section mismatches:
WARNING: drivers/built-in.o(.exit.text+0x5a): Section mismatch in reference from the function of_platform_serial_exit() to the variable .devinit.data:of_platform_serial_driver
The function __exit of_platform_serial_exit() references
a variable __devinitdata of_platform_serial_driver.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit e6bafba5b4 ("wmi: (!x & y)
strikes again"), a bug was fixed that involved converting !x & y to !(x
& y). The code below shows the same pattern, and thus should perhaps be
fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Lehmann <thomas.lehmann@alumni.tu-berlin.de> verified that this
entry works.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (35 commits)
Blackfin Serial Driver: Fix bug - Only insert UART rx char in timer task.
Blackfin Serial Driver: Fix bug - update tx dma buffer tail before wake up processes.
Blackfin Serial Driver: Fix bug - Increase buffer tail immediately before starting tx dma.
[Blackfin] serial driver: Add flow control support to bf54x
[Blackfin] serial driver: Fix bug Poll RTS/CTS status in DMA mode as well
[Blackfin] serial driver: ADSP-BF52x arch/mach support
[Blackfin] serial driver: use simpler comment headers and strip out information that is maintained in the scm's log
[Blackfin] serial driver: rework break flood anomaly handling to be more robust/realistic about what we can actually work around
[Blackfin] serial driver: fix bug - cache the bits of the LSR on systems where the LSR is read-to-clear
[Blackfin] serial driver: fix bug - should not wait for the TFI bit, just clear it when tx stop.
[Blackfin] serial driver: Fix bug serial driver in DMA mode spams history to console on shell restart
[Blackfin] serial driver: Fix bug Free rx dma buffer in shutdown.
[Blackfin] serial driver: Clean up UART DMA code.
Blackfin Serial driver: Fix bug - serial driver in PIO mode cant handle input very quickly
[Blackfin] arch: kill section mismatch warnings
[Blackfin] arch: handle the most common L1 shrinkage case (L1 does not exist for a part) so that any parts labeled for L1 instead get placed into external memory sections
[Blackfin] arch: add bfin_clear_PPIx_STATUS() helper funcs like we have for other parts
[Blackfin] arch: make sure we have proper description/copyright/license lines
[Blackfin] arch: Fix CONFIG_PM support for BF561
[Blackfin] arch: Remove DPMC char driver option
...
This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.
This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We should only return IRQ_HANDLED when we actually found something to
handle. This is important since the USART interrupt handler may be
shared with the timer interrupt on some chips.
Pointed-out-by: michael <trimarchi@gandalf.sssup.it>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm/hardware.h doesn't exist any more, and the definitions sh-sci.h
depended on are provided through asm/cpu/addrspace.h these days.
Kill off the bogus include.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7366 cpu supports. Just the most basic things like interrupt
controller, clocks and serial port are included at this point.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is an outdated comment in serial_core.c also fixed.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When possible, pass the tty name to request_irq() so that the user can easily
distinguish the different serial ports in /proc/interrupts.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by David Brownell, we really ought to be using container_of
when converting from "struct uart_port *" to "struct atmel_uart_port *".
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduced by atmel_serial-split-the-interrupt-handler.patch.
Thanks to michael <trimarchi@gandalf.sssup.it> for spotting it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is based on the DMA-patch by Chip Coldwell for the AT91/AT32 serial
USARTS, with some tweaks to make it apply neatly on top of the other patches
in this series.
The RX and TX code has been moved to a tasklet and reworked a bit. Instead of
depending on the ENDRX and TIMEOUT bits in CSR, we simply grab as much data as
we can from the DMA buffers. I think this closes a race where the ENDRX bit
is set after we read CSR but before we read RPR, although I haven't confirmed
this.
Similarly, the two TX handlers (ENDTX and TXBUFE) have been combined into one.
Since the current code only uses a single TX buffer, there's no point in
handling those interrupts separately.
This also fixes a DMA sync bug in the original patch.
[linux@bohmer.net: rebased onto irq-splitup patch]
[hskinnemoen@atmel.com: moved to tasklet, fixed dma bug, misc cleanups]
[hskinnemoen@atmel.com: atmel_serial dma: Misc fixes and cleanups]
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split up the interrupt handler of the serial port into a interrupt top-half
and a tasklet.
The goal is to get the interrupt top-half as short as possible to minimize
latencies on interrupts. But the old code also does some calls in the
interrupt handler that are not allowed on preempt-RT in IRQF_NODELAY context.
This handler is executed in this context because of the interrupt sharing with
the timer interrupt. The timer interrupt on Preempt-RT runs in IRQF_NODELAY
context.
The tasklet takes care of handling control status changes, pushing incoming
characters to the tty layer, handling break and other errors. It also handles
pushing TX data into the data register.
Reading the complete receive queue is still done in the top-half because we
never want to miss any incoming character.
[hskinnemoen@atmel.com: misc cleanups and simplifications]
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an error happens in probe(), the clocks should be disabled, but
only if the port isn't already used as a console.
In remove(), the port struct shouldn't be freed because it's defined
statically.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If BRGR is zero, the baud rate generator isn't running, so the boot loader
can't have initialized the port.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace two instances of barrier() with cpu_relax() since that's the right
thing to do when busy-waiting. This does not actually change anything since
cpu_relax() is defined as barrier() on both ARM and AVR32.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up the atmel_serial driver to conform the coding rules. It contains no
functional change.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a set of changes to implement proper resource management in the
driver, including iomem space reservation and operating on physical
addresses ioremap()ped appropriately using accessory functions rather than
unportable direct assignments.
Some adjustments to code are made to reflect the architecture of the
interface, which is a centrally controlled multiport (or, as referred to
from DEC documentation, a serial line multiplexer, going up to 8 lines
originally) rather than a bundle of separate ports.
Types are changed, where applicable, to specify the width of hardware
registers explicitly. The interrupt handler is now managed in the
->startup() and ->shutdown() calls for consistency with other drivers and
also in preparation to handle the handover from the initial firmware-based
console gracefully.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all casts from "struct uart_port *" to "struct dz_port *" with a
construct based on container_of(). This makes the conversion work
irrespective of where the former struct is located within the latter.
By popular request I have implemented it as an inline function rather than
a macro this time.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A set of changes to the way termios settings are propagated to the serial
port hardware. The DZ11 only supports a selection of fixed baud settings,
so some requests may not be fulfilled. Keep the old setting in such a case
and failing that resort to 9600bps. Also add a missing update of the
transmit timeout. And remove the explicit encoding of the line selected
from writes to the Line Parameters Register as it has been preencoded by
the ->set_termios() call already. Finally, remove a duplicate macro for
the Receiver Enable bit.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle the read and ignore status masks correctly. Handle the BREAK condition
as expected: a framing error with a null character is a BREAK, any other
framing error is a framing error indeed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ->start_tx(), ->stop_tx() and ->stop_rx() backends are called with the
port's lock already taken. Remove locking from within them and wrap around
calls as necessary.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the serial console structure so that `modpost' does not complain about
a reference to an "init" section -- "_console" is magic.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat the Kconfig entries and update descriptions for accuracy. Select the
driver by default for configurations of interest. For the curious: 32BIT
means only 32-bit DECstations support the device, not that the driver is not
64-bit clean; I have not checked that either though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sort the header inclusions, add a few that are needed but pulled indirectly
only and remove ones that are not really used.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Well, panic() is a little bit undue if request_irq() fails; there is probably
no need to justify it any further. Handle the case gracefully, by
unregistering the driver.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Polled transmission is tricky enough with the DZ11 design. While "loop" is
set to a high value, conceptually you are not allowed to transmit without
checking whether the device offers the right transmission line (yes, it is the
device that selects the line -- the driver has no control over it other than
disabling the transmitter offered if it is the wrong one), so the loop has to
be run at least once.
Well, the '1977 or PDP11 view of how serial lines should be handled... Except
that the serial interface used to be quite an impressive board back then
rather than chip.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused module function prototypes that would not even build if enabled.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When rebasing one of the mpc5200 psc UART patches I made a mistake and
damaged the patch.
This patch fixes the compile failure introduced in commit
25ae3a0739
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add 512x support using the psc_ops framework established
with the previous patch.
All 512x PSCs share the same interrupt so add
IRQF_SHARED to irq flags.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
PSC devices are different between the mpc5200 and the mpc5121
this patch localizes the differences in preparation for adding mpc5121
support to the psc uart driver.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
New serial driver for SC2681/SC2691 uarts. Older SNI RM400 machines are
using these chips for onboard serial ports.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Torben Mathiasen <device@lanana.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use SGI_HAS_ZILOG for IP22_ZILOG depends
- remove IP22 from description, because the driver works on more than
IP22 SGI machines
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Probing of the console at console_initcall time is broken. It tries to
call memory allocation routines which aren't initialized yet.
Problem solved by removing the early probe entirely. The console init
is called again anyway after the uartlite device is initialized and the
memory allocation routines can be called safely.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Mainly, this involves two changes:
1) xilinx->xlnx (recognized standard is to use the stock ticker)
2) In order to have the device tree focus on describing what the
hardware is as exactly as possible, the compatible strings contain the
full IP name and IP version.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
