Add @is_cmd to ata_tf_to_fis(). This controls bit 7 of the second
byte which tells the device whether this H2D FIS is for a command or
not. This cleans up ahci a bit and will be used by PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_tf_read was setting HOB bit when lba48 command was submitted, but
was not clearing it before reading "normal" data. As it is only place
which sets HOB bit in control register, and register reads should not
be affected by other bits, let's just clear it when we are done with
reading upper bytes so non-48bit commands do not have to touch ctl
at all.
pata_scc suffered from same problem...
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes some issues of the previous patch:
- Use mode_filter() hook to limit ATAPI UDMA mode
- "data loss" warning message
- handling of udma_mask
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit df69c9c543 moved only prototype of
out of CONFIG_PM. Move function out as well. Box seems to boot fine.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Yay, the first one from Seagate. 3.ALC firmware is okay. This was
reported by Sam Freed on bugzilla bug 8759.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Sam Freed <sam@freed.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pata_platform: Fix NULL pointer dereference
pata_platform currently dereferences a NULL pointer in pata_platform_probe()
if pdev->dev.platform_data is set to NULL. This breakage was most likely
introduced by commit 5f45bc5097.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* trim trailing whitespace
* document some flags, registers, and register bits
* fix locking around EDMA on/off and configuration
* continue replacing "constant OP var" with "var OP constant"
* use new pci_try_set_mwi()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The appletouch geyser3 devices found in the Intel Macs (and possibly
some later PPC ones?) send a constant stream of packets after the first
touch. This results in the kernel waking up around once every couple of
milliseconds to process them, making it almost impossible to spend any
significant amount of time in C3 state on a dynamic HZ kernel. Sending
the mode initialization code makes the device shut up until it's touched
again. This patch does so after receiving 10 packets with no interesting
content.
Signed-off-by: Soeren Sonnenburg <kernel@nn7.de>
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The "id" property in vdc-port nodes are not unique, they
are all zero. Therefore assign ID's using the parent's
"cfg-handle" property which will be unique.
Signed-off-by: David S. Miller <davem@davemloft.net>
and populate it with the common parts from PowerPC and Sparc[64].
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
This just moves the common stuff from the arch of_device.h files to
linux/of_device.h.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
This moves all the common parts for the Sparc, Sparc64 and PowerPC
of_device.c files into drivers/of/device.c.
Apart from the simple move, Sparc gains of_match_node() and a call to
of_node_put in of_release_dev(). PowerPC gains better recovery if
device_create_file() fails in of_device_register().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
This consolidates the routines of_find_node_by_path, of_find_node_by_name,
of_find_node_by_type and of_find_compatible_device. Again, the comparison
of strings are done differently by Sparc and PowerPC and also these add
read_locks around the iterations.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
This adds a read_lock around the child/next accesses on Sparc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
This requires creating dummy of_node_{get,put} routines for sparc and
sparc64. It also adds a read_lock around the parent accesses.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
The only change here is that a readlock is taken while the property list
is being traversed on Sparc where it was not taken previously.
Also, Sparc uses strcasecmp to compare property names while PowerPC
uses strcmp.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
The only difference here is that Sparc uses strncmp to match compatibility
names while PowerPC uses strncasecmp.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
This creates drivers/of/base.c (depending on CONFIG_OF) and puts
the first trivially common bits from the prom.c files into it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Both shwdt and rtc-sh are only supported on SH-3 and SH-4 at
the moment, don't allow them to break the SH-2 and SH-5 (sh64)
builds.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch incorporates some updates. Updates include:
- Fix the problem that control transfer might fail
- Change from GFP_KERNEL to GFP_ATOMIC
- Clean up some coding style issue
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as940 renames hcd_data_lock in hcd.c to hcd_urb_list_lock,
which is more descriptive of the lock's job. It also introduces a
convenient inline routine for testing whether a particular USB device
is a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as939) moves a couple of routine in hcd.c around. The
purpose is to put all the general URB- and endpoint-related routines
(submit, unlink, giveback, and disable) together in one spot.
There are no functional changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch incorporates some updates from the review of the
Renesas m66592-udc driver. Updates include:
- Fix some locking bugs; and add a few sparse annotations
- Don't #define __iomem !
- Lots of whitespace fixes (most of the patch by volume)
- Some #include file trimmage
- Other checkpatch.pl and sparse updates
- Alphabetized and slightly-more-informative Kconfig
- Don't use the ID which was assigned to the amd5536udc driver.
- Remove pointless suspend/resume methods updating obsolete field.
- Some section fixups
- Fix some leak bugs
- Fix byteswapping
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as938) adds an unusual_devs entry for the Nikon DSC D100.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Coverity scan found (CID: 1708) this in
drivers/usb/serial/io_ti.c::edge_shutdown() :
...
2797 for (i=0; i < serial->num_ports; ++i) {
2798 edge_port = usb_get_serial_port_data(serial->port[i]);
2799 edge_remove_sysfs_attrs(edge_port->port);
2800 if (edge_port) {
2801 edge_buf_free(edge_port->ep_out_buf);
2802 kfree(edge_port);
2803 }
2804 usb_set_serial_port_data(serial->port[i], NULL);
2805 }
...
It's complaining that we dereference 'edge_port' in line 2799 which
makes the test of that pointer against NULL in 2800 pointless, since if
edge_port was actually NULL we'd have crashed already before reaching
line 2800.
Reading the edge_open() function it seems to me that the pointer
returned by usb_get_serial_port_data(serial->port[i]) and stored in
'edge_port' can never actually be NULL here, so the test is entirely
superfluous (even if it could be NULL it would be pointless here,
ignoring the then possible crash in that case, since both
edge_buf_free() and kfree() can handle being passed NULL pointers.
This patch removes the pointless conditional (and also makes a few
tiny style corrections now that I was in the area anyway).
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver for the AMD5536 UDC, as found in the AMD Geode CS5536 (southbridge).
This is a high speed DMA-capable controller, which can also be used in
OTG configurations (which are not supported by this patch).
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as936) updates the kerneldoc for usb_unlink_urb. The
explanation of how endpoint queues are meant to work is now clearer
and in better agreement with reality.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It has recently been pointed out that short control transfers should
have a status stage, even if they generate an error because
URB_SHORT_NOT_OK was set. This patch (as935) changes uhci-hcd to
enable the status stage when this happens.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Coverity (1709, 1710, 1711, 1712, 1713) actually flagged these as
REVERSE_INULLs (NULL check performed after dereference). But looking at
the other drivers I can't see any similar tests and the USB core already
makes sure urb is non-null - so might as well get rid of the checks.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as937) fixes a minor bug in the autosuspend usage-counting
code. Each hub's usage counter keeps track of the number of
unsuspended children. However the current driver increments the
counter after registering a new child, by which time the child may
already have been suspended and caused the counter to go negative.
The obvious solution is to increment the counter before registering
the child.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as934) adds a new readonly binary sysfs attribute file
called "descriptors" for each USB device. The attribute contains the
device descriptor followed by the raw descriptor entry (config plug
subsidiary descriptors) for the current configuration.
Having this information available in fixed-format binary makes life a
lot easier for user programs by avoiding the need to open, read, and
parse multiple sysfs text files.
The information in this attribute file is much like that in usbfs's
device file, but there are some significant differences:
The 2-byte fields in the device descriptor are left in
little-endian byte order, as they appear on the bus and
in the kernel.
Only one raw descriptor set is presented, that of the
current configuration.
Opening this file will not cause a suspended device to be
autoresumed.
The last item in particular should be a big selling point for libusb,
which currently forces all USB devices to be resumed as it scans the
device tree.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Dave Mielke <dave@mielke.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as931b), adapted from a patch by Olav Kongas, makes a small
set of conservative changes to the isp116x-hcd driver in preparation
for the removal of urb->status.
finish_request() is moved up in the source and is called
as soon as the URB is known to have completed, rather than
after all the active endpoints have been scanned.
The status of a completed URB is kept in a local variable
and copied to urb->status only when the URB is about to be
given back.
-EREMOTEIO error status for control transfers is set after
the status stage rather than when the short packet arrives.
Some unnecessary uses of urb->lock are removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found the first regresson in the rewritten ("all dynamic" and "no races")
driver. If application uses O_NONBLOCK, I return -EAGAIN despite the URB
being submitted successfuly. This causes the application to resubmit the
same data erroneously.
The fix is to pretend that the transfer has succeeded even if URB was
merely queued. It is the same behaviour as with the old version.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds new devices to the Sierra Wireless driver. This is being
resubmitted because the dependent patch (patch 01/02) needed to be
resubmitted.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds compatibility with Sierra Wireless' new TRU-Install
feature. Future devices that use this feature will not work unless this
patch has been applied.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The FTDI ELAN driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Adutux driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ELAN U132 adapter driver uses the semaphore u132_module_lock
as mutex. Use the mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB gadget serial driver uses a semaphore as mutex. Use the
mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that ide-floppy supports SG_IO we can add support for SCSI ioctls
(except deprecated SCSI_IOCTL_SEND_COMMAND and legacy CDROM_SEND_PACKET
ones - we can add them later iff really needed).
While at it remove handling of CDROMEJECT and CDROMCLOSETRAY ioctls from
generic_ide_ioctl():
- This prevents ide-{disk,tape,scsi} device drivers from obtaining
REQ_TYPE_BLOCK_PC type requests which are currently unsupported by
these drivers and which are potentially harmful (as reported by Andrew).
- There is no functionality loss since aforementioned ioctls will now be
handled by idefloppy_ioctl()->scsi_cmd_ioctl() (for devices using
ide-floppy driver) and by idecd_ioctl->cdrom_ioctl()->scsi_cmd_ioctl()
(for devices using ide-cd driver).
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ATA_PIO[0-6] defines to <linux/ata.h>.
* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.
* Add PIO masks to host drivers.
<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->host_flags to ide_hwif_t to store ide_pci_device_t.host_flags,
assign it in setup-pci.c:ide_pci_setup_ports().
* Add IDE_HFLAG_PIO_NO_{BLACKLIST,DOWNGRADE} to ide_pci_device_t.host_flags
and teach ide_get_best_pio_mode() about them. Also remove needless
!drive->id check while at it (drive->id is always present).
* Convert amd74xx, via82cxxx and ide-timing.h to use ide_get_best_pio_mode()
and then remove no longer needed ide_find_best_pio_mode().
There should be no functionality changes caused by this patch.
Acked-by: Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
and convert all users accordingly.
* Remove no longer needed ide_pio_data_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Check IORDY bit for PIO modes > 2.
* Some devices claim maximum PIO mode > 2 in id->tPIO, they were punished too
severly for this by being limited to PIO_SLOW. Limit them to PIO2 instead.
v2:
* Fix PIO number being returned incorrectly instead of PIO mode
(Noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_pio_cycle_time() helper.
* Use it in ali14xx/ht6560b/qd65xx/cmd64{0,x}/sl82c105 and pmac host drivers
(previously cycle time given by the device was only used for "pio" == 255).
* Remove no longer needed ide_pio_data_t.cycle_time field.
v2:
* Fix "ata_" prefix (Noticed by Jeff).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Nowadays core IDE code handles restoring of PIO and DMA modes
(ide-io.c:ide_start_power_step() etc) so remove open-coded version
from sc1200_resume().
There should be no change in behavior because settings done by
sc1200_resume() were always overridden by generic_ide_resume()
and ide_{start,stop}_power_step().
* Bump driver version.
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Do the same thing as probe_hwif() and always disable DMA so chipset DMA
enabled bit gets cleared (if the drive doesn't support DMA ide_set_dma()
won't try to tune it anyway).
* Add TODO comment about respecting ->using_dma setting.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver used to depend on BIOS settings for deciding whether it is OK
to use DMA. However it seems that BIOS doesn't always handle all cases
correctly so just let IDE core to decide about this. It should be a safe
thing to do now, after the driver went through heavy bugfixing.
Thanks for bugreport and testing the patch goes out to Sven Niedner.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Always set ->autotune so PIO gets correctly auto-tuned (previously
->autotune was only set when ->dma_base wasn't available, however
->ide_dma_check()/->speedproc() was always trying to tune PIO when
tuning DMA).
* Move code responsible for programming chipset for PIO mode from
svwks_tune_chipset() to svwks_tune_pio(). Don't tune PIO when tuning
DMA (this is no longer needed since ->autotune is always set now).
* Handle PIO modes early in svwks_tune_chipset() so DMA configuration
registers don't get cleared when programming PIO mode.
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.
* Add IDE_HFLAG_SINGLE flag for single channel devices.
* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
and remove no longer needed ide_pci_device_t.channels field.
v2:
* Fix issues noticed by Sergei:
- correct code alignment in scc_pata.c
- s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Print info about overriding PIO mode in ide_get_best_pio_mode().
* Remove info about overriding PIO mode from cmd64{0,x} host drivers.
* Remove no longer needed ide_pio_data_t.overridden field.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add sil_tuneproc() wrapper for siimage_tuneproc() which also sets
PIO mode on the device.
* Add missing ide_get_best_pio_mode() call to sil_tuneproc() so
"pio" == 255 (autotune) is handled correctly (previously PIO0 was used)
and "pio" values > 4 && < 255 are filtered to PIO4 (instead of PIO0).
* Add code limiting maximum PIO mode according to the pair device capabilities
to sil_tuneproc().
* Convert users of config_siimage_chipset_for_pio() to use sil_tune_pio() and
sil_tuneproc(). This fixes PIO fallback in siimage_config_drive_for_dma() to
use max PIO mode available instead of PIO4 (config_siimage_chipset_for_pio()
used wrong arguments for ide_get_best_pio_mode() and as a results always
tried to set PIO4).
* Remove no longer needed siimage_taskfile_timing()
and config_siimage_chipset_for_pio().
* Enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
from siimage_speedproc()
* Bump driver version.
v2:
* Fix issues noticed by Sergei:
- correct pair device check
- trim only taskfile PIO to the slowest of the master/slave
- enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
from siimage_speedproc()
- add TODO item for IORDY bugs
- minor cleanups
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off exisiting atiixp_tuneproc() into atiixp_tune_pio()
and then add setting device PIO mode to atiixp_tuneproc().
* Add missing ide_get_best_pio_mode() call to atiixp_tuneproc() so
"pio" == 255 (autotune) is handled correctly and "pio" values > 4 && < 255
are filtered to PIO4 (previously "pio" == 5 could result in wrong timings
being used and "pio" values > 4 && < 255 in an OOPS).
* Handle PIO modes early in atiixp_speedproc() so save_mdma_mode[]
doesn't get cleared.
* In atiixp_dma_check():
- fix max_mode argument for ide_get_best_pio_mode()
- don't call atiixp_dma_2_pio() so PIO1 doesn't get remapped to PIO0
- use atiixp_tuneproc() instead of atiixp_speedproc()
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Various old IDE drivers go mapping ROM devices for no apparent reason and
without using the ROM mapping API we now have. They don't actually use
the ROM they map and the new libata drivers are happy without it being
mapped so rather than port them lets just junk it for the next -rc1.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The two CONFIG variables
CONFIG_ETRAX_IDE_CSE1_16_RESET
CONFIG_ETRAX_IDE_CSP0_8_RESET
appear to have been dead since way back in 2.5.xx days:
http://www.linuxhq.com/kernel/v2.5/75/arch/cris/drivers/Kconfig
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Michael Starvik <starvik@axis.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
One card submitted by user.
Signed-off-by: Marcin Juszkiewicz <openembedded@hrw.one.pl>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Workaround for errata A308: turn down the UDMA mode and retry
the DMA command when the data lost condition is detected.
take2:
udma_filter() hook is used to limit ATAPI UDMA mode.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move to using inline function variant of eieio instead of inline assmebly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: kou.ishizaki@toshiba.co.jp
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently, CONFIG_X86_CMPXCHG64 both enables boot-time checking of
the cmpxchg64b feature and enables compilation of the set_64bit() family.
Since the option is dependent on PAE, and since KVM depends on set_64bit(),
this effectively disables KVM on i386 nopae.
Simplify by removing the config option altogether: the boot check is made
dependent on CONFIG_X86_PAE directly, and the set_64bit() family is exposed
without constraints. It is up to users to check for the feature flag (KVM
does not as virtualiation extensions imply its existence).
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (33 commits)
xtensa: use DATA_DATA in xtensa
powerpc: add missing DATA_DATA to powerpc
cris: use DATA_DATA in cris
kallsyms: remove usage of memmem and _GNU_SOURCE from scripts/kallsyms.c
kbuild: use -fno-optimize-sibling-calls unconditionally
kconfig: reset generated values only if Kconfig and .config agree.
kbuild: fix the warning when running make tags
kconfig: strip 'CONFIG_' automatically in kernel configuration search
kbuild: use POSIX BRE in headers install target
Whitelist references from __dbe_table to .init
modpost white list pattern adjustment
kbuild: do section mismatch check on full vmlinux
kbuild: whitelist references from variables named _timer to .init.text
kbuild: remove hardcoded _logo names from modpost
kbuild: remove hardcoded apic_es7000 from modpost
kbuild: warn about references from .init.text to .exit.text
kbuild: consolidate section checks
kbuild: refactor code in modpost to improve maintainability
kbuild: ignore section mismatch warnings originating from .note section
kbuild: .paravirtprobe section is obsolete, so modpost doesn't need to handle it
...
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: (44 commits)
i2c: Delete the i2c-isa pseudo bus driver
hwmon: refuse to load abituguru driver on non-Abit boards
hwmon: fix Abit Uguru3 driver detection on some motherboards
hwmon/w83627ehf: Be quiet when no chip is found
hwmon/w83627ehf: No need to initialize fan_min
hwmon/w83627ehf: Export the thermal sensor types
hwmon/w83627ehf: Enable VBAT monitoring
hwmon/w83627ehf: Add support for the VID inputs
hwmon/w83627ehf: Fix timing issues
hwmon/w83627ehf: Add error messages for two error cases
hwmon/w83627ehf: Convert to a platform driver
hwmon/w83627ehf: Update the Kconfig entry
make coretemp_device_remove() static
hwmon: Add LM93 support
hwmon: Improve the pwmN_enable documentation
hwmon/smsc47b397: Don't report missing fans as spinning at 82 RPM
hwmon: Add support for newer uGuru's
hwmon/f71805f: Add temperature-tracking fan control mode
hwmon/w83627ehf: Preserve speed reading when changing fan min
hwmon: fix detection of abituguru volt inputs
...
Manual fixup of trivial conflict in MAINTAINERS file
If root raised the default wakeup threshold over the size of the
output pool, the pool transfer function could overflow the stack with
RNG bytes, causing a DoS or potential privilege escalation.
(Bug reported by the PaX Team <pageexec@freemail.hu>)
Cc: Theodore Tso <tytso@mit.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this patch the abituguru refuses to load on non Abit motherboards, as
discussed in lkml CONFIG_BREAK_MY_MACHINE thread.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch changes the driver to also detect uguru3's which hold 0x08 at DATA
initially, as has been reported here:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=220160
Also when an uguru3's holds 0x0014 in the ID register it will now report
"Abit AB9 Pro" as motherboard identification.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
We don't need to initialize fan_min in this driver, as the fan_div
attributes are read-only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add support for the w83627ehf thermal sensor types. I made them read-only,
as the BIOS is supposed to set them up properly. This information makes it
easier to find out which temperature channel corresponds to the CPU.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
If VBAT monitoring is disabled, enable it. Original patch from
an anonymous contributor on the lm-sensors trac system:
http://lm-sensors.org/ticket/2218
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The W83627EHF and similar chips have 6 VID input pins, add support
for them. The driver changes the input voltage level automatically
if the current setting is not correct for the detected CPU model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* I have experimental evidence that the W83627EHG needs more than 1
second to refresh all the measured values. Increase the caching time to
1.5 second.
* When changing a fan clock divider, the corresponding fan speed
measurement register is no longer valid, until the next time the chip
will refresh it. One way to fix this is to pretend that the cache is
still valid for one more period (1.5 second.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
If the Super-I/O device is disabled, it is likely the BIOS has a good
reason for leaving it disabled, so give a warning when enabling it --
it's not likely to be wired correctly or be able to give good data.
Also, if the Super-I/O device is configured with an address of 0, the
driver refuses to initialize it.
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Remove i2c-isa from the w83627ehf driver, and use a platform driver
instead.
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add description for the W83627DHG chip to Kconfig.
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
coretemp_device_remove() can become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds support for the LM93 hardware monitoring chip.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Also protects ourselves against a possible division by zero.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds a new driver for the hardware monitoring features of the
third revision of the Abit uGuru chip, found on recent Abit
motherboards. This is an entirely different beast then the first and
second revision (its again a winbond microcontroller, but the "protocol"
to talk to it and the bank addresses are very different.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add support for the "temperature mode" fan speed control. In this mode,
the user can define 3 temperature/speed trip points, and the chip will
set the speed automatically according to the temperature changes.
Signed-off-by: Phil Endecott <kernel@chezphil.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The w83627ehf driver changes the fan clock divider automatically when
a new min fan speed is set. It is supposed to preserve the fan speed
reading while doing so, bug doesn't really. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch fixes the detection of volt inputs with a reading of more then 240
units.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds the SMSC SCH5317 chip (device ID 0x85) as a supported
device to the smsc47b397 driver.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This is the patch for converting it87 to a platform driver (and remove i2c-isa).
Signed-off-by: Corentin LABBE <corentin.labbe@geomatys.fr>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix a potential race condition when some hardware monitoring platform
drivers are being unloaded. I believe that the driver data pointer
shouldn't be cleared before all the sysfs files are removed, otherwise
a sysfs callback might attempt to dereference a NULL pointer. I'm not
sure exactly what the driver core protects drivers against, so let's
play it safe.
While we're here, clear the driver data pointer when probe fails, so
as to not leave an invalid pointer behind us.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Convert the vt8231 driver from the nonsensical i2c-isa hack to a
regular platform driver.
Signed-off-by: Roger Lucas <roger@planbit.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix the writing of the temperature interrupt configuration.
The old code was working only by accident.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for IT8726F chip driver, which is just same as
IT8716F with additional glue logic for AMD power sequencing.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We have the following naming convention documented in
Documentation/hwmon/sysfs-interface for fault files:
in[0-*]_input_fault
fan[1-*]_input_fault
temp[1-*]_input_fault
Some drivers follow this convention (lm63, lm83, lm90, smsc47m192).
However some drivers omit the "input" part and create files named
fan1_fault (pc87427) or temp1_fault (dme1737). And the new "generic"
libsensors follows this second (non-standard) convention, so it fails
to report fault conditions for drivers which follow the standard.
We want a single naming scheme, and everyone seems to prefer the
shorter variant, so let's go for it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use platform_device_add_data() in hardware monitoring drivers. This
makes the code nicer and smaller too. Reported by David Hubbard.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Convert the pc87360 driver from the nonsensical i2c-isa hack to a
regular platform driver. This is a direct conversion, other cleanups
could happen on top of that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
Add support for the hardware monitoring and fan control
capabilities of the SMSC DME1737 and Asus A8000 Super-I/O chips.
The hardware monitoring logic of this chip is similar to the LM85 but
has some additional features that this driver supports. Even though
it's a Super-I/O chip, the hardware monitoring logic can only be
accessed via SMBus.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This lets us get rid of macro-generated functions and shrinks the
driver size by about 8%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
* Discard comments which do not apply or are redundant.
* Remove a few useless instructions.
* Rename new_client to just client.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
ide-disk calls
ide_end_request(drive, 0, 0);
to finish an unknown request, but this doesn't work so well for non-fs
requests, since ide_end_request() internally looks at ->hard_cur_sectors
to see how much data to end. Only file system requests store a transfer
value in there, pc requests fill out ->data_len as a byte based transfer
value instead.
Since we ask to end 0 bytes of that request, it will never be terminated
and ide-disk gets stuck in a loop "handling" that same request over and
over.
Switch __ide_end_request() to take a byte based transfer count, and
adjust ide_end_request() to look at the right field to determine how
much IO to end when it's being passed in 0.
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-By: Giacomo Catenazzi <cate@debian.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some simple fixes to properly reference counter values from the block
attribute level of edac_device objects. Properly sequencing the array pointer
was added, resulting in correct identification of block level attributes from
their base class functions.
Added more verbose debug statement for event tracking.
Also during some corner testing, found a bug in the store/show sequence
of operations for the block attribute/controls management.
An old intermediate structure for 'blocks' was still in the processing
pipeline. This patch removes that old structure and correctly utilizes the
new struct edac_dev_sysfs_block_attribute for passing control from the sysfs
to the low level store/show function of the edac driver.
Now the proper kobj pointer to passed downward to the store/show
functions.
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mutex locking deadlock on the device controller linked list. Was calling
a lock then a function that could call the same lock. Moved the cancel workq
function to outside the lock
Added some short circuit logic in the workq code
Added comments of description
Code tidying
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With feedback, this patch corrects operation of the kobject release operation
on kobjects, attributes and controls for the edac_device.
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch refactors the 'releasing' of kobjects for the edac_mc type of
device. The correct pattern of kobject release is followed.
As internal kobjs are allocated they bump a ref count on the top level kobj.
It in turn has a module ref count on the edac_core module. When internal
kobjects are released, they dec the ref count on the top level kobj. When the
top level kobj reaches zero, it decrements the ref count on the edac_core
object, allow it to be unloaded, as all resources have all now been released.
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactoring of sysfs code necessitated the refactoring of the
edac_device_alloc() and edac_device_add_device() apis, of moving the index
value to the alloc() function. This patch alters the in tree drivers to
utilize this new api signature.
Having the index value performed later created a chicken-and-the-egg issue.
Moving it to the alloc() function allows for creating the necessary sysfs
entries with the proper index number
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactoring of sysfs code necessitated the refactoring of the edac_mc_alloc()
and edac_mc_add_mc() apis, of moving the index value to the alloc() function.
This patch alters the in tree drivers to utilize this new api signature.
Having the index value performed later created a chicken-and-the-egg issue.
Moving it to the alloc() function allows for creating the necessary sysfs
entries with the proper index number
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes and enhances the driver level set of sysfs attributes that
can be added to the 'block' level of an edac_device type of driver.
There is a controller information structure, which contains one or more
instances of device. Each instance will have one or more blocks of device
specific counters. This patch fixes the ability to have more detailed
attributes/controls for each of the 'blocks', providing for the addition of
controls/attributes from the low level driver to user space via sysfs.
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NEW EDAC driver for the memory controllers on PA Semi PA6T-1682M.
Changes since last submission:
* Rebased on top of 2.6.22-rc4-mm2 with the EDAC changes merged there.
* Minor checkpatch.pl cleanups
* Renamed ctl_name
* Added dev_name
* edac_mc.h -> edac_core.h
[akpm@linux-foundation.org: make printk more informative]
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Egor Martovetsky <egor@pasemi.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Doug Thompson <dougthompson@xmission.com
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found a 'reversal' decoding bug in the driver. This patch fixes that mapping
to correctly display the CSROW entries in their proper order. Users will be
enable to correctly identifiy the failing DIMM with this fix.
[akpm@linux-foundation.org: unneeded (and undesirable) cast of void*]
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Mark Grondona <mgrondona@llnl.gov>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A previous patch changed the edac_mc src file from semaphore usage to mutex
This patch changes the edac_device src file as well, from semaphore use to
mutex operation.
Use a mutex primitive for mutex operations, as it does not require a
semaphore
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactored the function edac_op_state_toString() to be edac_op_state_to_string()
for consistent style, and its callers
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactor the edac_align_ptr() function to reduce the noise of casting the
aligned pointer to the various types of data objects and modified its callers
to its new signature
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the file edac_device.c perform some coding style enhancements
Add some function header comments
Made for better readability commands
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various code style conformance patches on the i5000 driver
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patches to conform to coding style, namely static don't need to be initialized
to NULL nor '0', as that is the default
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found a typo in one of the #defines in the driver
MTR_DIM_RANKS --> MTR_DIMM_RANK
Signed-off-by: Marisuz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Compiling this module gave a warning that the return value of
'pci_bus_add_device()' was not checked.
This patch adds that check and an output message
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If ERRSTS indicates that there's no error then we don't need to bother reading
the other registers.
In addition to making the common case faster, this actually fixes a small race
where we don't see an error but we clear the error bits anyway, potentially
wiping away info on an error that happened in the interim (or where a CE
arrives between the first and second read of ERRSTS, causing us to falsely
claim "UE overwrote CE").
Signed-off-by: Jason Uhlenkott <juhlenko@akamai.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) Remove an old CVS ID string
2) change EDAC from a tristate option to a simple bool option
3) In addition to the X86 arch, PPC and MIPS also have drivers in the
submission queue. This patch turns on the EDAC flag for those archs. Each
driver will have its respective 'depends on ARCH' set.
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes some remnant spaces inserted by the use of Lindent.
Seems Lindent adds some spaces when it shoulded. These have been fixed.
In addition, goto targets have issues, these have been fixed
in this patch.
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kconfig - modified the help of EDAC
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error handling output strings needed to be refactored for better
displaying of the error informaton.
Also needed to added offset_value for output as well
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added new controls for the edac_device and edac_mc sysfs folder.
These can be initialized by the low level driver to provide misc
controls into the low level driver for its use
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move x86 drivers to new pci controller setup
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Run r82600_edac.c file through Lindent for cleanup
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Run i82443bxgx.c file through Lindent for cleanup
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Run e752x_edac.c file through Lindent for cleanup
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ran e752x_edac.c file through Lindent for cleanup
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ran this driver through Lindent for cleanup
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The origin of this code comes from patches at sourceforge, that
allow EDAC to be updated to various kernels. With kernel version 2.6.20 a
new workq system was installed, thus the patches needed to be modified
based on the kernel version. For submitting to the latest kernel.org
those #ifdefs are removed
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removal of some old dead and disabled code from the edac_device sysfs code
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Run the EDAC CORE files through Lindent for cleanup
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup poll values for MC and PCI.
Also make mc function names unique to mc.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmissin.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change error check and clear variable from an atomic to an int
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Moving PCI to a per-instance device model
This should include the correct sysfs setup as well. Please review.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the memory controller object to work queue based implementation from the
kernel thread based.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's a driver for the Intel 3000 and 3010 memory controllers,
relative to today's Sourceforge code drop. This has only had light
testing (I've yet to actually see it handle a memory error) but it
detects my hardware correctly.
Signed-off-by: Jason Uhlenkott <juhlenko@akamai.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move dev_name() macro to a more generic interface since it's not possible
to determine whether a device is pci, platform, or of_device easily.
Now each low level driver sets the name into the control structure, and
the EDAC core references the control structure for the information.
Better abstraction.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the refactoring of edac_mc.c into several subsystem files,
the header file edac_mc.h became meaningless. A new header file
edac_core.h was created. All the files that previously included
"edac_mc.h" are changed to include "edac_core.h".
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provides a way for NMI reported errors on x86 to notify the EDAC
subsystem pending ECC errors by writing to a software state variable.
Here's the reworked patch. I added an EDAC stub to the kernel so we can
have variables that are in the kernel even if EDAC is a module. I also
implemented the idea of using the chip driver to select error detection
mode via module parameter and eliminate the kernel compile option.
Please review/test. Thx!
Also, I only made changes to some of the chipset drivers since I am
unfamiliar with the other ones. We can add similar changes as we go.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It will claim the PCI devices from under intel_agp.ko's feet. Greg is brewing
some fix for that.
Cc: Douglas Thompson <dougthompson@xmission.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a NEW EDAC Memory Controller driver for the 440BX chipset (I82443BXGX)
created and submitted by Timm Small
Signed-off-by: Tim Small <tim@buttersideup.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch to fix some scrubbing #defines in the edac_core.h file
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Wollesen ported the Bluesmoke Memory Controller driver (written by Doug
Thompson) for the Intel 5000X/V/P (Blackford/Greencreek) chipset to the in
kernel EDAC model.
This patch incorporates the module for the 5000X/V/P chipset family
[m.kozlowski@tuxland.pl: edac i5000 parenthesis balance fix]
Signed-off-by: Eric Wollesen <ericw@xmtp.net>
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The EDAC core code uses a semaphore as mutex. use the mutex API
instead of the (binary) semaphore.
Matthaias wrote this, but since I had some patches ahead of it,
I need to modify it to follow my patches.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding missing mem types for use in the sysfs presentation file for
Memory Controller device objects.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new 'class' of object to be managed, named: 'edac_device'.
As a peer of the 'edac_mc' class of object, it provides a non-memory centric
view of an ERROR DETECTING device in hardware. It provides a sysfs interface
and an abstraction for varioius EDAC type devices.
Multiple 'instances' within the class are possible, with each 'instance'
able to have multiple 'blocks', and each 'block' having 'attributes'.
At the 'block' level there are the 'ce_count' and 'ue_count' fields
which the device driver can update and/or call edac_device_handle_XX()
functions. At each higher level are additional 'total' count fields,
which are a summation of counts below that level.
This 'edac_device' has been used to capture and present ECC errors
which are found in a a L1 and L2 system on a per CORE/CPU basis.
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a large patch to refactor the original EDAC module in the kernel
and to break it up into better file granularity, such that each source
file contains a given subsystem of the EDAC CORE.
Originally, the EDAC 'core' was contained in one source file: edac_mc.c
with it corresponding edac_mc.h file.
Now, there are the following files:
edac_module.c The main module init/exit function and other overhead
edac_mc.c Code handling the edac_mc class of object
edac_mc_sysfs.c Code handling for sysfs presentation
edac_pci_sysfs.c Code handling for PCI sysfs presentation
edac_core.h CORE .h include file for 'edac_mc' and 'edac_device' drivers
edac_module.h Internal CORE .h include file
This forms a foundation upon which a later patch can create the 'edac_device'
class of object code in a new file 'edac_device.c'.
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes needlessly global code static, in the edac core
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This simple patch adds an important CORE API for EDAC that EDAC drivers can
use to find their edac_mc control structure by passing a mem_ctl_info
'instance' value
Needed for subsequent patches
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lguest net driver
A simple net driver for lguest.
[akpm@linux-foundation.org: include fix]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the Kconfig and Makefile to allow lguest to actually be
compiled.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the code for the "lg.ko" module, which allows lguest guests to
be launched.
[akpm@linux-foundation.org: update for futex-new-private-futexes]
[akpm@linux-foundation.org: build fix]
[jmorris@namei.org: lguest: use hrtimers]
[akpm@linux-foundation.org: x86_64 build fix]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
