This allows metadata writebacks which are issued via block device
writeback to be sent with the current write request flags.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
So we can better understand what bits of ext4 are responsible for
long-running jbd2 handles, use jbd2__journal_start() so we can pass
context information for logging purposes.
The recommended way for finding the longer-running handles is:
T=/sys/kernel/debug/tracing
EVENT=$T/events/jbd2/jbd2_handle_stats
echo "interval > 5" > $EVENT/filter
echo 1 > $EVENT/enable
./run-my-fs-benchmark
cat $T/trace > /tmp/problem-handles
This will list handles that were active for longer than 20ms. Having
longer-running handles is bad, because a commit started at the wrong
time could stall for those 20+ milliseconds, which could delay an
fsync() or an O_SYNC operation. Here is an example line from the
trace file describing a handle which lived on for 311 jiffies, or over
1.2 seconds:
postmark-2917 [000] .... 196.435786: jbd2_handle_stats: dev 254,32
tid 570 type 2 line_no 2541 interval 311 sync 0 requested_blocks 1
dirtied_blocks 0
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Move the jbd2 wrapper functions which start and stop handles out of
super.c, where they don't really logically belong, and into
ext4_jbd2.c.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The function ext4_handle_dirty_super() was calculating the superblock
on the wrong block data. As a result, when the superblock is modified
while it is mounted (most commonly, when inodes are added or removed
from the orphan list), the superblock checksum would be wrong. We
didn't notice because the superblock *was* being correctly calculated
in ext4_commit_super(), and this would get called when the file system
was unmounted. So the problem only became obvious if the system
crashed while the file system was mounted.
Fix this by removing the poorly designed function signature for
ext4_superblock_csum_set(); if it only took a single argument, the
pointer to a struct superblock, the ambiguity which caused this
mistake would have been impossible.
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
The '__ext4_handle_dirty_metadata()' does not need the 'now' argument
anymore and we can kill it.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
This patch changes the 'ext4_handle_dirty_super()' function which
submits the superblock for I/O in the following cases:
1. When creating the first large file on a file system without
EXT4_FEATURE_RO_COMPAT_LARGE_FILE feature.
2. When re-sizing the file-system.
3. When creating an xattr on a file-system without the
EXT4_FEATURE_COMPAT_EXT_ATTR feature.
If the file-system has journal enabled, the superblock is written via
the journal. We do not modify this path.
If the file-system has no journal, this function, falls back to just
marking the superblock as dirty using the 's_dirt' superblock
flag. This means that it delays the actual superblock I/O submission
by 5 seconds (default setting). Namely, the 'sync_supers()' kernel
thread will call 'ext4_write_super()' later and will actually submit
the superblock for I/O.
And this is the behavior this patch modifies: we stop using 's_dirt'
and just mark the superblock buffer as dirty right away. Indeed, all 3
cases above are extremely rare and it does not add any value to delay
the I/O submission for them.
Note: 'ext4_handle_dirty_super()' executes
'__ext4_handle_dirty_super()' with 'now = 0'. This patch basically
makes the 'now' argument unneeded and it will be deleted in one of the
next patches.
This patch also removes 's_dirt' condition on the unmount path because
we never set it anymore, so we should not test it.
Tested using xfstests for both journalled and non-journalled ext4.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Calculate and verify the superblock checksum. Since the UUID and
block group number are embedded in each copy of the superblock, we
need only checksum the entire block. Refactor some of the code to
eliminate open-coding of the checksum update call.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add debugging information in case jbd2_journal_dirty_metadata() is
called with a buffer_head which didn't have
jbd2_journal_get_write_access() called on it, or if the journal_head
has the wrong transaction in it. In addition, return an error code.
This won't change anything for ocfs2, which will BUG_ON() the non-zero
exit code.
For ext4, the caller of this function is ext4_handle_dirty_metadata(),
and on seeing a non-zero return code, will call __ext4_journal_stop(),
which will print the function and line number of the (buggy) calling
function and abort the journal. This will allow us to recover instead
of bug halting, which is better from a robustness and reliability
point of view.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The block allocation code used to use jbd2_journal_get_undo_access as
a way to make changes that wouldn't show up until the commit took
place. The new multi-block allocation code has a its own way of
preventing newly freed blocks from getting reused until the commit
takes place (it avoids updating the buddy bitmaps until the commit is
done), so we don't need to use jbd2_journal_get_undo_access(), which
has extra overhead compared to jbd2_journal_get_write_access().
There was one last vestigal use of ext4_journal_get_undo_access() in
ext4_add_groupblocks(); change it to use ext4_journal_get_write_access()
and then remove the ext4_journal_get_undo_access() support.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Save number of file system errors, and the time function name, line
number, block number, and inode number of the first and most recent
errors reported on the file system in the superblock.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We don't need to set s_dirt in most of the ext4 code when journaling
is enabled. In ext3/4 some of the summary statistics for # of free
inodes, blocks, and directories are calculated from the per-block
group statistics when the file system is mounted or unmounted. As a
result the superblock doesn't have to be updated, either via the
journal or by setting s_dirt. There are a few exceptions, most
notably when resizing the file system, where the superblock needs to
be modified --- and in that case it should be done as a journalled
operation if possible, and s_dirt set only in no-journal mode.
This patch will optimize out some unneeded disk writes when using ext4
with a journal.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Calls to ext4_handle_dirty_metadata should only pass in an inode
pointer for inode-specific metadata, and not for shared metadata
blocks such as inode table blocks, block group descriptors, the
superblock, etc.
The BUG_ON can get tripped when updating a special device (such as a
block device) that is opened (so that i_mapping is set in
fs/block_dev.c) and the file system is mounted in no journal mode.
Addresses-Google-Bug: #2404870
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Just a pet peeve of mine; we had a mishash of calls with either __func__
or "function_name" and the latter tends to get out of sync.
I think it's easier to just hide the __func__ in a macro, and it'll
be consistent from then on.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Convert the last two callers of ext4_journal_forget() to use
ext4_forget() instead, and then fold ext4_journal_forget() into
ext4_forget(). This reduces are code complexity and shortens our call
stack.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The only caller of ext4_journal_revoke() is ext4_forget(), so we can
fold ext4_journal_revoke() into ext4_forget() to simplify the code and
shorten the call stack.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The ext4_forget() function better belongs in ext4_jbd2.c. This will
allow us to do some cleanup of the ext4_journal_revoke() and
ext4_journal_forget() functions, as well as giving us better error
reporting since we can report the caller of ext4_forget() when things
go wrong.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When there is no journal present, we must attach buffer heads
associated with extent tree and indirect blocks to the inode's
mapping->private_list via mark_buffer_dirty_inode() so that
ext4_sync_file() --- which is called to service fsync() and
fdatasync() system calls --- can write out the inode's metadata blocks
by calling sync_mapping_buffers().
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When ext4 is using a journal, a metadata block which is deallocated
must be passed into the journal layer so it can be dropped from the
current transaction and/or revoked. This is done by calling the
functions ext4_journal_forget() and ext4_journal_revoke(), which call
jbd2_journal_forget(), and jbd2_journal_revoke(), respectively.
Since the jbd2_journal_forget() and jbd2_journal_revoke() call
bforget(), if ext4 is not using a journal, ext4_journal_forget() and
ext4_journal_revoke() must call bforget() to avoid a dirty metadata
block overwriting a block after it has been reallocated and reused for
another inode's data block.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We found a problem with buffer head reference leaks when using an ext4
partition without a journal. In particular, calls to ext4_forget() would
not to a brelse() on the input buffer head, which will cause pages they
belong to to not be reclaimable.
Further investigation showed that all places where ext4_journal_forget() and
ext4_journal_revoke() are called are subject to the same problem. The patch
below changes __ext4_journal_forget/__ext4_journal_revoke to do an explicit
release of the buffer head when the journal handle isn't valid.
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
A few weeks ago I posted a patch for discussion that allowed ext4 to run
without a journal. Since that time I've integrated the excellent
comments from Andreas and fixed several serious bugs. We're currently
running with this patch and generating some performance numbers against
both ext2 (with backported reservations code) and ext4 with and without
a journal. It just so happens that running without a journal is
slightly faster for most everything.
We did
iozone -T -t 4 s 2g -r 256k -T -I -i0 -i1 -i2
which creates 4 threads, each of which create and do reads and writes on
a 2G file, with a buffer size of 256K, using O_DIRECT for all file opens
to bypass the page cache. Results:
ext2 ext4, default ext4, no journal
initial writes 13.0 MB/s 15.4 MB/s 15.7 MB/s
rewrites 13.1 MB/s 15.6 MB/s 15.9 MB/s
reads 15.2 MB/s 16.9 MB/s 17.2 MB/s
re-reads 15.3 MB/s 16.9 MB/s 17.2 MB/s
random readers 5.6 MB/s 5.6 MB/s 5.7 MB/s
random writers 5.1 MB/s 5.3 MB/s 5.4 MB/s
So it seems that, so far, this was a useful exercise.
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Move ext4 headers out of include/linux. This is just the trivial move,
there's some more thing that could be done later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
