In order to get exact 24MHz clock frequency value for the camera
sensor and avoid rounding errors the parent clock must be CLK_XUSBXTI,
not CLK_MOUT_MPLL_USER_T. Currently the sensor's master clock
frequency is too high and the sensor doesn't work properly.
This fixes commit 0357a4438d
("ARM: dts: Specify default clocks for Exynos4 camera devices").
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Assign proper FIMC-IS UART gate clock in the device DT node and not
use the SRC_MASK gate. This fixes regression introduced in commit
a37c82a3b3 ("clk: samsung: exynos4: Remove
SRC_MASK_ISP gates").
Without this change exynos4 fimc-is driver fails to probe with an
error log:
[ 1.842447] ERROR: could not get clock /camera/fimc-is@12000000:uart(13)
[ 1.848529] exynos4-fimc-is 12000000.fimc-is: failed to get clock: uart
[ 1.855275] exynos4-fimc-is: probe of 12000000.fimc-is failed with error -2
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add to Trats2 DTS new node for configuring the max77693 charger driver.
Only the maxim,constant-microvolt differs from default value but set all
of the optional properties anyway.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Remove fixed regulators (duplicating what max77686 provides) and
add GPIO enable control to max77686 regulators.
This gives the system full control over those regulators. Previously
the state of such regulators was a mixture of what max77686 driver set
over I2C and what regulator-fixed set through GPIO.
Removal of 'regulator-always-on' from CAM_ISP_CORE_1.2V (buck9) allows
disabling it when it is not used. Previously this regulator was always
enabled because its enable state is a OR of:
- ENB9 GPIO (turned always on by regulator-fixed),
- BUCK9EN field in BUCK9CTRL register (off by max77686 through I2C).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add suspend to RAM configuration for max77686 regulators. Some LDOs
and bucks are disabled. This reduces energy consumption during S2R,
approximately from 17 mA to 9 mA.
Additionally remove old and not supported bindings:
- regulator-mem-off
- regulator-mem-idle
- regulator-mem-on
The max77686 driver does not parse them and they are not documented
anywere.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add node for fuel gauge present in Maxim 77693 PMIC. This allows control
over battery charging state on Trats2 board.
The fuel gauge is compatible with max17042 battery driver (Maxim
17042/17047/17050). Although datasheet rev 2.2 for MAX77693 describes
fuel gauge as Maxim 17042-like, the chip on Trats2 board identifies
itself as Maxim 17047-like.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The charge delay value is by default 0x400. But it can be set to lower
values on some boards, as long as false pen-ups are avoided. Lowering the
value increases the sampling rate (though current sampling rate is
sufficient for TSC operation). In some boards, the value has to be
increased to avoid false pen-up events. Hence, charge delay has been
made a DT parameter.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds stdout-path property to chosen nodes of Exynos4 boards
to enable use of earlycon feature without the need to hardcode port
number in kernel itself.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- several fixes and adjustments following the last cleanup batch
- removal of some unused Kconfig options
- slight PM and pm_idle rework to ease future rework
- removal of unneeded mach/system_rev.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUxjj9AAoJEAf03oE53VmQGEAH/3nLneCOQeyuq60adx+Lxcdn
Q9sMMzrw4B6bQnJee7+PQD3/QU7fmF8qNKlMKYAlILFHGNQplASi4uAfRTykUA0j
RQHpS9n20ODVfX+yePJ/o8h2r1BkT2wUIDXxaZCj2RoPmEz1aiFDNa2pPsUfprRd
gpbh+ZU43LRowYwH9UHPV55PQ0ZwMq3ry2DOYY5Al1+bKQ8TFvAdDMUu3rGZU7A4
dMYiQCQ6Fv0EI1NY0IHSf/u/jujlPE2H0TSR38w8lYfIPzBx2tHkLSupuxKh7R1N
QYibgZXWR0PqHOXMpOHYBqJFj5c3f/aOZ/dO4RJha+S7YHNQnIFzLsm122njgKQ=
=KgUm
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup3' into at91-3.20-soc
One more week's worth of fixes. Worth pointing out here are:
- A patch fixing detaching of iommu registrations when a device is removed --
earlier the ops pointer wasn't managed properly
- Another set of Renesas boards get the same GIC setup fixup as others have in
previous -rcs
- Serial port aliases fixups for sunxi. We did the same to tegra but we
caught that in time before the merge window due to more machines being
affected. Here it took longer for anyone to notice.
- A couple more DT tweaks on sunxi
- A follow-up patch for the mvebu coherency disabling in last -rc batch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUzl/yAAoJEIwa5zzehBx3/v0P/iU4sCz/HYBwL46lSZZLnFyX
RDFiq+I6nQFM3CG6oRn0gEi+/GbdyQ/Q6kMbver216pSfymZ+agRFaA6oj1o4HRD
FQ2Dtz2ytvdkO8uSUzIV+nLJ//3MMwxmXTnB7SrDuzy6VeJ6GHlxxp39jrPCWtgi
z7eo1bAuEKRQpVqJLBbqaNTsc4+9990zcgz5ChvfCqOvY3rE/AElEF5CMk71TFHW
NTZQGM/HWteehA3/vTODICrd5SqV3peNAe3n6OMnZEEniUCesnug6IamUMwqKWVb
y8rgobVV6ow5F0Cr3Zxc9Ufj8R1yayRQoGOdzDfuQ+zPivi2NbseinQgMUVujXYh
TE/Ea4j+V1bYSY6EA89pAjw2C6e7fIWPOUJbO9hj5Ywc+uzR+ns+GFR2AaBggpFu
4h0ig0ceOkzTgDWW0fNhH6BysvvczErT1CD0l6B+QgUZQadbSCFcGe8k2pNuJvYG
f2lq6zUBIaNY5ZO6gu9inrd8UxjutKZM1p80fZc+tCFrm5YfHLFLwJPqfG7+8iEW
R5OoQ1Jjb5SdO7u1yH2znQtlM9Z1u7bGQ7BkWPfZ0XbkHqiVgCpBUigzlRSgFO0+
1rITIcwKgfdv8Sw4yngO6C3zFzn9Jz/cvGtW+gEjmSDV0BlhWCfWkTWys3ocdO79
JSToPOtd87iekn7nHLBY
=nw2v
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"One more week's worth of fixes. Worth pointing out here are:
- A patch fixing detaching of iommu registrations when a device is
removed -- earlier the ops pointer wasn't managed properly
- Another set of Renesas boards get the same GIC setup fixup as
others have in previous -rcs
- Serial port aliases fixups for sunxi. We did the same to tegra but
we caught that in time before the merge window due to more machines
being affected. Here it took longer for anyone to notice.
- A couple more DT tweaks on sunxi
- A follow-up patch for the mvebu coherency disabling in last -rc
batch"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm: dma-mapping: Set DMA IOMMU ops in arm_iommu_attach_device()
ARM: shmobile: r8a7790: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a73a4: Instantiate GIC from C board code in legacy builds
ARM: mvebu: don't set the PL310 in I/O coherency mode when I/O coherency is disabled
ARM: sunxi: dt: Fix aliases
ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
Looks like on 3517 davinci_emac MAC address registers have a
different layout compared to dm816x and am33xx.
Let's add a function to get the 3517 MAC address.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On this board USB2 is meant to be used as peripheral only.
The ID pin for USB2 is hardwired HIGH.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
NOTE: the ports on this board cannot switch roles. They are
configured either host or peripheral by hardwiring the
respective ID pins.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the hdmi driver is using one of the soc i2c busses for ddc probing
and while documentation always specifies i2c5 as hdmi-i2c it could very well
be any other bus as well.
Therefore this is a property of the board and should be specified there.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables the recently added display nodes on the firefly and evb,
letting the boards output graphic data over the hdmi port.
This includes enabling of i2c5 on the evb that is used for ddc probing and
setting the lcd-regulators to always on until the hdmi driver learns
about using them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use the same transfer speed on both the rk808 and act8846 variants and
remove the status=okay from the rk808 one which is already set in the
shared rk3288-evb.dtsi .
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The evaluation board using the act8846 as main pmic uses two additional
regulators to provide the cpu and gpu voltage. Add these and also add
the link to cpu supply from vdd_cpu.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9Imn
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 3rd DT updates for v3.20" from Kukjin Kim:
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add DISP1 power domain for exynos5420
clk: exynos5420: Add IDs for clocks used in DISP1 power domain
Signed-off-by: Olof Johansson <olof@lixom.net>
- for all of Samsung SoCs
: use generic power domain bindings
: add 'dr_mode' property for hsotg/dwc2 devices
- exynos3250-rinato and exynos3250-monk
: add regulator-haptic
- exynos5422-odroidxu3
: reduce total RAM by 22 MiB because last 22 MiB
for secure monitor cannot be accessed by kernel
: add on-board INA231 sensors and LDO26 of PMIC
for the sensors
Note that this is based on tags/samsung-dt
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DGVz
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 2nd DT updates for v3.20" from Kukjin Kim:
- for all of Samsung SoCs
: use generic power domain bindings
: add 'dr_mode' property for hsotg/dwc2 devices
- exynos3250-rinato and exynos3250-monk
: add regulator-haptic
- exynos5422-odroidxu3
: reduce total RAM by 22 MiB because last 22 MiB
for secure monitor cannot be accessed by kernel
: add on-board INA231 sensors and LDO26 of PMIC
for the sensors
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: reduce total RAM by 22 MiB for exynos5422-odroidxu3
ARM: dts: add on-board INA231 sensors for exynos5422-odroidxu3
ARM: dts: Add regulator-haptic node for exynos3250-monk
ARM: dts: Add regulator-haptic node for exynos3250-rinato
ARM: dts: add 'dr_mode' property to hsotg devices for exynos boards
ARM: dts: convert to generic power domain bindings for exynos DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the PCI controller node for the Versatile/PB board.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
The Versatile boards have the same sysregs as other ARM Ltd boards. Add
the nodes in order to enable support for 24MHz counter as sched_clock.
This is a minimal node definition as the existing sub node definition
used on VExpress has some issues raised by Linus W.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The DISP1 power domain on Exynos5420 SoC includes the FIMD1, MIXER
and HDMI modules. Add a device node for this power domain and mark
these modules as consumer of the DISP1 power domain.
When a power domain is powered on and off, the input clocks of the
devices attached to it are reparented. So a reference to the input
and parent clocks of the devices are needed to manage that.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Looks like I only got half done with moving pinctrl and syscon to
be children of the SCM. I've set up the FAPLL clocks that way already,
but did not complete the job as I copied the syscon values from
am33xx.dtsi.
To make sure the syscon mapping works, I've verfified that we can
set up davinci_emac mac address the same way as cpsw already does
with the syscon mapping. So let's add that too.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In one pinctrl node, a 'bias-disable' property is erroneously assigned a
value.
Fixes: ARM: zynq: DT: Add pinctrl information
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add the clock property for the watchdog on rk3288 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
for the broadcast timer going through the clocksource tree
and two new boards, the rk3288-based Firefly and the
PX2-based Rayeager board (the PX2 is identical to the rk3066
but made for industrial users).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUyCaJAAoJEPOmecmc0R2By0oH/ioVbVZWYgTWJRlN0Cmjj+yr
fNnzm93g9N+Uk5PGOjCw70h3QSS65OLdqPF9xJwkSS1p7ORbKmOU3fzAET7x/EYK
a3Ct4NRPPiSkY12Qg+N4Q9wjz8sgUUHsLSFa5D/QJsyPu+lTVhLgWS4j4mzVCbyz
PSMn4Tx52OHzLHWKGrnEq33AIMROvarBmOgnvGe7AbutwDYqoiFiPALIAowrp/SR
WY689+3Gjtha5epUHn9vgUkNABnf0gXR1MBBJ1ZMxgForjZqeSCioHNYomneKOZC
9zyg4yuv5kNL75PY4aHLwalRfIFrqNM5S5D3gH7CTQg1/TcfUcVCBY0CAKczLxw=
=nDW6
-----END PGP SIGNATURE-----
Merge tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: second batch of dts updates for 3.20" from Heiko Stübner:
Basic display nodes for crtcs and hdmi encoder, timer node
for the broadcast timer going through the clocksource tree
and two new boards, the rk3288-based Firefly and the
PX2-based Rayeager board (the PX2 is identical to the rk3066
but made for industrial users).
* tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board
ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards
dt-bindings: add vendor prefix and root compatible property for Rockchip boards
ARM: dts: rockchip: Add rockchip timer node for rk3288
ARM: dts: rockchip: add rk3288 hdmi nodes
ARM: dts: rockchip: Add rk3288 vop and display-subsystem
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull networking fixes from David Miller:
1) Don't OOPS on socket AIO, from Christoph Hellwig.
2) Scheduled scans should be aborted upon RFKILL, from Emmanuel
Grumbach.
3) Fix sleep in atomic context in kvaser_usb, from Ahmed S Darwish.
4) Fix RCU locking across copy_to_user() in bpf code, from Alexei
Starovoitov.
5) Lots of crash, memory leak, short TX packet et al bug fixes in
sh_eth from Ben Hutchings.
6) Fix memory corruption in SCTP wrt. INIT collitions, from Daniel
Borkmann.
7) Fix return value logic for poll handlers in netxen, enic, and bnx2x.
From Eric Dumazet and Govindarajulu Varadarajan.
8) Header length calculation fix in mac80211 from Fred Chou.
9) mv643xx_eth doesn't handle highmem correctly in non-TSO code paths.
From Ezequiel Garcia.
10) udp_diag has bogus logic in it's hash chain skipping, copy same fix
tcp diag used. From Herbert Xu.
11) amd-xgbe programs wrong rx flow control register, from Thomas
Lendacky.
12) Fix race leading to use after free in ping receive path, from Subash
Abhinov Kasiviswanathan.
13) Cache redirect routes otherwise we can get a heavy backlog of rcu
jobs liberating DST_NOCACHE entries. From Hannes Frederic Sowa.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (48 commits)
net: don't OOPS on socket aio
stmmac: prevent probe drivers to crash kernel
bnx2x: fix napi poll return value for repoll
ipv6: replacing a rt6_info needs to purge possible propagated rt6_infos too
sh_eth: Fix DMA-API usage for RX buffers
sh_eth: Check for DMA mapping errors on transmit
sh_eth: Ensure DMA engines are stopped before freeing buffers
sh_eth: Remove RX overflow log messages
ping: Fix race in free in receive path
udp_diag: Fix socket skipping within chain
can: kvaser_usb: Fix state handling upon BUS_ERROR events
can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUT
can: kvaser_usb: Send correct context to URB completion
can: kvaser_usb: Do not sleep in atomic context
ipv4: try to cache dst_entries which would cause a redirect
samples: bpf: relax test_maps check
bpf: rcu lock must not be held when calling copy_to_user()
net: sctp: fix slab corruption from use after free on INIT collisions
net: mv643xx_eth: Fix highmem support in non-TSO egress path
sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlers
...
- correct some pin configuration for at91sam9x5ek
- add pioD on sama5d4 following a modification of pinctrl driver
- add more precise nand compatibility string for sama5d4
- audio modifications for wm8904 or ac97
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUxmgWAAoJEAf03oE53VmQtCoIAJtnUtvW5DqRWWsAzKxv6tPF
FLXihD9MRPyywgN5hDvNInKibqcBNxnLfk0xiFbCbfZXU4u6SK1E5iJN72mkTxhP
6rC/rdMDqMqGK7W43h4xFFpQdPrrq00t36gGvnQ+IUaOYcGAByJPYB3YwKMv/n0x
xHTPhydb2RPphEd9ZaXsbUKcaOJPG/6uChQSTp+8L0MAlh4cQADya1SapDhRefDa
PFz49N8QIjxgjWyJiWorcD8KH8hkGzLtvuvDl3UWkNZz9i3h7Vl3QaraC3HCHqwm
kJrOJ/EVw1uJKAKtYoo9xfoA8Z5HHno3vcQ4gKq4ylYDHIB3P4UhQLaGlcqkZfk=
=yOLr
-----END PGP SIGNATURE-----
Merge tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "at91: dt for 3.20 #2" from Nicolas Ferre:
Second DT batch for 3.20:
- correct some pin configuration for at91sam9x5ek
- add pioD on sama5d4 following a modification of pinctrl driver
- add more precise nand compatibility string for sama5d4
- audio modifications for wm8904 or ac97
* tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sam9263: Add ac97 device node
dt: atmel_ac97c: Add device tree documentation
ARM: at91: at91sam9n12ek/dt: use dt ids for wm8904
ARM: at91: sama5d3xek/dt: use dt ids for wm8904
ARM: at91: sama5d4: dts: change the nand compatible string
ARM: at91/dt: sama5d4: add pioD controller
ARM: at91/dt: disable pull-up on vbus-gpio (PB16) to reduce power consumption
Signed-off-by: Olof Johansson <olof@lixom.net>
A lot of changes to the device tree for the 3.20 merge window, mostly with:
- More DT license convertions, only two DTS and two DTSI are still uncertain
and have not been converted yet
- Use the C-preprocessor includes in the device trees.
- Add support for the A31s SoC and improve the A80 support
- Add IR receiver, lradc, PS/2 support
- Add cpufreq support for all SoCs but the A23 and A80.
- And a lot of new boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pWBS
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner device tree changes for 3.20" from Maxime Ripard:
A lot of changes to the device tree for the 3.20 merge window, mostly with:
- More DT license convertions, only two DTS and two DTSI are still uncertain
and have not been converted yet
- Use the C-preprocessor includes in the device trees.
- Add support for the A31s SoC and improve the A80 support
- Add IR receiver, lradc, PS/2 support
- Add cpufreq support for all SoCs but the A23 and A80.
- And a lot of new boards
* tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (64 commits)
ARM: dts: sun5i: Enable axp209 support on A13-OLinuxIno
ARM: sunxi: dts: Add A10/A20 PS2 pin muxing options
ARM: sunxi: dts: Add PS2 nodes to dtsi for A10,A20
ARM: dts: sun6i: Add resistive touchscreen controller node to dtsi
ARM: dts: sun4i: Add Hyundau A7HD board
ARM: dts: sun4i: Add Marsboard A10 board
ARM: dts: sun9i: Enable mmc2 on A80 Optimus Board
ARM: dts: sun9i: Add 8 bit mmc pinmux setting for mmc2
ARM: dts: sun9i: Enable mmc0 on A80 Optimus Board
ARM: dts: sun9i: Convert a80 optimus board dts to label referencing
ARM: dts: sun9i: Add mmc controller nodes to the A80 dtsi
ARM: dts: sun9i: Add mmc config clock nodes
ARM: dts: sunxi: Add missing mdio label
ARM: dts: sun5i: Add mk802_a10s board
ARM: dts: sun4i: Add mk802ii board
ARM: dts: sun4i: Add mk802 board
ARM: dts: sun4i: Add dts file for Chuwi V7 CW0825 tablet
ARM: dts: sun7i: Add dts file for Bananapro board
ARM: sun6i: Enable ARM arch timers
ARM: dts: sun6i: Convert hummingbird a31 dts to label references
...
Signed-off-by: Olof Johansson <olof@lixom.net>
A few minor fixes for the 3.19 kernel:
- The 8250 uart driver now respects the aliases, which pointed out that we
were using them wrong. Fixed them.
- The simplefb pipeline that was used on the A10 caused flickering and
tearing, and rendered it pretty much useless. Added a new simplefb node
with another pipeline that removes this issue. Note that we need to keep
the old node because u-boot 2015.01 uses it.
- Added a fix for the USB phy node on sun4i/sun5i
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JLlc
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 3.19" from Maxime Ripard:
Allwinner fixes for 3.19
A few minor fixes for the 3.19 kernel:
- The 8250 uart driver now respects the aliases, which pointed out that we
were using them wrong. Fixed them.
- The simplefb pipeline that was used on the A10 caused flickering and
tearing, and rendered it pretty much useless. Added a new simplefb node
with another pipeline that removes this issue. Note that we need to keep
the old node because u-boot 2015.01 uses it.
- Added a fix for the USB phy node on sun4i/sun5i
* tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: dt: Fix aliases
ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
Signed-off-by: Olof Johansson <olof@lixom.net>
- exynos3250
: add exynos_usbphy node and hsotg nodes
- exynos3250-rinato
: enable usb
: cleanup and use macro for gpio-keys
: add fimd and Panel devices support
- exynos3250-monk
: enable usb
: cleanup and use macro for gpio-keys
- exynos5250-snow
: add power and lid gpio-keys pinctrl
- exynos5420-peach-pit and exynos5800-peach-pi
: configure regulators for suspend
: set always on for USB webCam regulators
: add lid GPIO key device
- exynos5422
: add support new board Odroid XU3
- dt-bindings
: add exynos-chipid
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Yc7r
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v3.20" from Kukjin Kim:
- exynos3250
: add exynos_usbphy node and hsotg nodes
- exynos3250-rinato
: enable usb
: cleanup and use macro for gpio-keys
: add fimd and Panel devices support
- exynos3250-monk
: enable usb
: cleanup and use macro for gpio-keys
- exynos5250-snow
: add power and lid gpio-keys pinctrl
- exynos5420-peach-pit and exynos5800-peach-pi
: configure regulators for suspend
: set always on for USB webCam regulators
: add lid GPIO key device
- exynos5422
: add support new board Odroid XU3
- dt-bindings
: add exynos-chipid
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Configure regulators for suspend on exynos Peach boards
ARM: dts: Set Peach boards USB WebCam regulators to always on
ARM: dts: Add lid GPIO key device node for Peach boards
ARM: dts: Add power and lid GPIO keys pinctrl for exynos5250-snow
Documentation: dt-bindings: add exynos-chipid binding information
ARM: dts: add Panel device support for exynos3250-rinato
ARM: dts: add fimd device support for exynos3250-rinato
ARM: dts: use macro in gpio keys for exynos3250 boards
ARM: dts: remove unnecessary gpio-key nodes for exynos3250 boards
ARM: dts: Enable USB node for exynos3250-monk
ARM: dts: Enable USB node for exynos3250-rinato
ARM: dts: Add hsotg node for exynos3250
ARM: dts: Add exynos_usbphy node for exynos3250
ARM: dts: Add dts file for Odroid XU3 board
Signed-off-by: Olof Johansson <olof@lixom.net>
The entries are separated as ARM V4/V5 and ARM V7 as some other per-SoC config
options may be removed in the near future.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Benoit Masson <yahoo@perenite.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ben Peddell <klightspeed@killerwolves.net>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ryan Press <ryan@presslab.us>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ryan Press <ryan@presslab.us>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The twl4030 keypad is not wired up in the gta04, so mark it disabled
to avoid pointless initialization.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
i.e. configure vpll2 as a supply for the dss rather
than being always-on.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add comments to state which GPIO is used for some interrupts.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mcbsp2 is used in gta04 soundcard config and by default
is disabled so enable it for gta04.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the device node for the ac97 controller.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-By Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Using the wm8904 device tree compatible string.
Signed-off-by: Alexander Morozov <linux@meltdown.ru>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As we introduce a new "atmel,sama5d4-nand" compatible string for sama5d4,
so we need to apply it for sama5d4 chip.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
A week's worth of fixes for various ARM platforms. Diff wise, the
largest fix is for OMAP to deal with how GIC now registers interrupts
(irq_domain_add_legacy() -> irq_domain_add_linear() changes).
Besides this, a few more renesas platforms needed the GIC instatiation
done for legacy boards. There's also a fix that disables coherency of
mvebu due to issues, and a few other smaller fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nrT2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A week's worth of fixes for various ARM platforms. Diff wise, the
largest fix is for OMAP to deal with how GIC now registers interrupts
(irq_domain_add_legacy() -> irq_domain_add_linear() changes).
Besides this, a few more renesas platforms needed the GIC instatiation
done for legacy boards. There's also a fix that disables coherency of
mvebu due to issues, and a few other smaller fixes"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: add baud rate to Juno stdout-path
ARM: dts: imx25: Fix PWM "per" clocks
bus: mvebu-mbus: fix support of MBus window 13
Merge tag 'mvebu-fixes-3.19-3' of git://git.infradead.org/linux-mvebu into fixes
ARM: mvebu: completely disable hardware I/O coherency
ARM: OMAP: Work around hardcoded interrupts
ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
This add support for Rayeager PX2, Rockchip PX2 based development board
made by ChipSPARK.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds support for Firefly-RK3288, Rockchip RK3288 based development
boards made by Firefly.
There are 2 dts for 2 versions of the board. rk3288-firefly-beta.dts is
for the beta version, rk3288-firefly.dts is for the mass production version.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[removed gmac reference, due to the gmac node going through the net-tree]
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3288 board uses the architected timers and these ones are shutdown when
the cpu is powered down. There is a need of a broadcast timer in this case to
ensure proper wakeup when the cpus are in sleep mode and a timer expires.
Add the timer node for the broadcast timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Commit f77d55a3b5 ("serial: 8250_dw: get index of serial line from DT
aliases") made the serial driver now use the serial aliases to get the tty
number, pointing out that our aliases have been wrong all along.
Remove them from the DTSI and add custom ones in the relevant boards.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The (non micro) A13-OLinuxIno has an axp203 pmic, enable support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: VishnuPatekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The commit (3d125f9c91) cause i.MX6SX sdb enet cannot work. The cause is
the commit add mdio node with un-correct phy address.
The patch just correct i.MX6sx sdb board enet phy address.
V2:
* As Shawn's suggestion that unit-address should match 'reg' property, so
update ethernet-phy unit-address.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, dwmac-rk uses a custom propety "phy_regulator" to get the name of the
right regulator to use to power on or power off the phy. This commit converts the
driver to use phy-supply devicetree property and the corresponding API, it cleans
the code a bit and make it simpler to maintain. This also replaces the property
phy_regulator by the standard property phy-supply in rk3288-evb-rk808.dts.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we support the sun6i variant of the touchscreen controller,
add the device node to the dtsi so we can use it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Last 22 MiB is RAM is reserved by secure monitor code and cannot be
accessed from Linux kernel, so adjust total RAM size to 0x7EA00000
(2 GiB - 22 MiB). This fixes random 'imprecise kernel abort' kernel
failures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The odroid-xu3 has 4 INA231 current sensors on board which can be
accessed from the Linux via the hwmon interface.
There is one sensor for each of these power rails:
- A15 cluster: VDD_ARM
- A7 cluster: VDD_KFC
- GPU: VDD_G3D
- memory: VDD_MEM
In addition to adding the sensors, LDO26 from the PMIC needs to be
enabled because it's powering these sensor.
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
