The driver would fail to stop the command timer in most error paths,
something which specifically could lead to the timer being freed while
still active on I/O errors during probe.
Fix this by making sure that each function starting the timer also stops
it in all relevant error paths.
Reported-by: syzbot+1d1597a5aa3679c65b9f@syzkaller.appspotmail.com
Fixes: b78e91bcfb ("rsi: Add new firmware loading method")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to stop both URBs before returning after failed probe as well
as on disconnect to avoid use-after-free in the completion handler.
Reported-by: syzbot+b563b7f8dbe8223a51e8@syzkaller.appspotmail.com
Fixes: a4302bff28 ("rsi: add bluetooth rx endpoint")
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Cc: stable <stable@vger.kernel.org> # 3.15
Cc: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Fariya Fatima <fariyaf@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwYyqAAoJEG4XJFUm622b/jMH/0KUcGz8y4gkk2B2lMRyUOTu
t84LiSHxcsq6letlr/vak4S6NrxMLP8Z/ByyoKC8o3yeVsdyMNMSLZAztFFhxdXr
Haky2SM10q6vnn9s1skXS/qkHSd2WdUFT2DgYxyOPCtJUazVKjcboJ4YX/TUg99a
5eqPpZ4RXtW6uOmWHS7JXtLcCFPywKPBtMAjLEDMYOUSSBWExBNyNZNhznSS3ywY
4VKvc675gXE+WD3qXRhL8EJjyed94yuS3wYbKWp8iTaIRyluDmc5lVhjWH1A0HLE
Qb62QL8XLtbX5fcTnaupdAIXwxeIBylOBe8QtW7QUbAnGFf8bexLxfnQM+To4wI=
=24zD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
USB core will never call a USB-driver probe function with a NULL
device-id pointer.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit f170d44bc4.
USB core will never call a USB-driver probe function with a NULL
device-id pointer.
Reverting before removing the existing checks in order to document this
and prevent the offending commit from being "autoselected" for stable.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The id pointer can be NULL in rsi_probe(). It is checked everywhere except
for the else branch in the idProduct condition. The patch adds NULL check
before the id dereference in the rsi_dbg() call.
Fixes: 54fdb318c1 ("rsi: add new device model for 9116")
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In rsi_send_beacon, if rsi_prepare_beacon fails the allocated skb should
be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
`dev` (struct rsi_91x_usbdev *) field of adapter
(struct rsi_91x_usbdev *) is allocated and initialized in
`rsi_init_usb_interface`. If any error is detected in information
read from the device side, `rsi_init_usb_interface` will be
freed. However, in the higher level error handling code in
`rsi_probe`, if error is detected, `rsi_91x_deinit` is called
again, in which `dev` will be freed again, resulting double free.
This patch fixes the double free by removing the free operation on
`dev` in `rsi_init_usb_interface`, because `rsi_91x_deinit` is also
used in `rsi_disconnect`, in that code path, the `dev` field is not
(and thus needs to be) freed.
This bug was found in v4.19, but is also present in the latest version
of kernel. Fixes CVE-2019-15504.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.4.
Major changes:
brcmfmac
* enable 160 MHz channel support
rt2x00
* add support for PLANEX GW-USMicroN USB device
rtw88
* add Bluetooth coexistance support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdWsySAAoJEG4XJFUm622b0I4H/3dnhfTUYeP6+2T5Q2KWJOKh
+uMLGBz+vzOaRoUFM6+Ar2rT7nUT3ias+XuWiVJ2R0HrgtYeXZrdOwPjbvrpMOkl
kEZAwc174HzGaGeNzF8WT5OLLqap/v18dc8HnstI49vsPzaY7PWLmDkXeTR65x+4
6sG0aj/Ggqv2pnEdhJhGPdR6G6R6AKCL50LiMpZNeDUolCtR15IOlZDubZ3VBbFr
ubAgOqmIeeXdix0yaKWycxDO0h8OQOBE09rT796FIhzss6DRAE8mWJjqllFp1rIp
JMbzcMcsTUXPV8tXcmlqPfTAFRkIu/RbO2prHHBu7A+kuHQfdpRlpA8EpUxB2IQ=
=6nQp
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-08-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.4
First set of patches for 5.4.
Major changes:
brcmfmac
* enable 160 MHz channel support
rt2x00
* add support for PLANEX GW-USMicroN USB device
rtw88
* add Bluetooth coexistance support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue: While removing and inserting the driver module, observed driver
loading is not successful.
Root cause: Card is not resetted completely without issuing cmd5.
Fix: Issued cmd5 properly.
Signed-off-by: Ganapathi Kondraju <ganapathirajukondraju@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Issue: RS-9116 Card is not responding after firmware got loaded.
Root cause: After firmware got loaded, we need to reset the program
counter and few device specific registers. Those registers were not
resetted properly.
Fix: Properly resetting those registers.
Signed-off-by: Ganapathi Kondraju <ganapathirajukondraju@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Explicitly return constants instead of variable (and rely on
it to be explicitly initialized), if the value is supposed
to be fixed anyways. Align it with the rest of the driver,
which does it the same way.
Signed-off-by: Enrico Weigelt <info@metux.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When building with -Wuninitialized, Clang warns:
drivers/net/wireless/rsi/rsi_91x_sdio.c:940:43: warning: variable 'data'
is uninitialized when used here [-Wuninitialized]
put_unaligned_le32(TA_HOLD_THREAD_VALUE, data);
^~~~
drivers/net/wireless/rsi/rsi_91x_sdio.c:930:10: note: initialize the
variable 'data' to silence this warning
u8 *data;
^
= NULL
1 warning generated.
Using Clang's suggestion of initializing data to NULL wouldn't work out
because data will be dereferenced by put_unaligned_le32. Use kzalloc to
properly initialize data, which matches a couple of other places in this
driver.
Fixes: e5a1ecc97e ("rsi: add firmware loading for 9116 device")
Link: https://github.com/ClangBuiltLinux/linux/issues/464
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Below changes are done:
* Device 80MHz clock should be disabled for 9116 in 20MHz band.
* Default edca parameters should be used initially before
connection.
* Default TA aggregation is 3 for 9116.
* Bootup parameters should be loaded first when channel is
changed.
* 4 byte register writes are possible for 9116.
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Device reset register(watchdog timer related) addresses and
values are different for 9116.
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For 9116 device, we have introduced w9116 features frame, which shall be
send when radio capabilities confirm is received.
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bootup parameters are different for 9116 device. Check added for device
model where-ever bootup parameters are being send.
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initial frame exchange sequence has been changed for 9116 chip. Getting MAC
address using EEPROM read frame will be once common device configuration is
done and RESET_MAC frame is sending after bootup parameters confirmation is
received, which are different from RS9113 device
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New firmware files and firmware loading method are added for 9116.
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Till software bootloader ready state, communication with device is common
for 9113 and 9116. Hence moved that part of firmware loading to separate
function rsi_prepare_fw_load(). Also LMAC_VER_OFFSET is different for 9113
and 9116, so renamed existing macro to LMAC_VER_OFFSET_9113
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9116 device id entry is added in both SDIO and USB interfaces.
New enumberation value taken for the device model. Based on the
device model detected run time, few device specific operations
needs to be performed.
adding rsi_dev_model to get device type in run time, as we can use
same driver for 9113 and 9116 except few firmware load changes.
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
kmalloc can fail in rsi_register_rates_channels but memcpy still attempts
to write to channels. The patch replaces these calls with kmemdup and
passes the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The call to ieee80211_probereq_get can return NULL if a skb allocation
fails, so add a null pointer check and free an earlier skb on the error
exit return path.
Fixes: 7fdcb8e126 ("rsi: add support for hardware scan offload")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/rsi/rsi_91x_main.c: In function 'rsi_prepare_skb':
drivers/net/wireless/rsi/rsi_91x_main.c:127:24: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rsi/rsi_91x_main.c:124:28: warning:
variable 'info' set but not used [-Wunused-but-set-variable]
They're not used any more since 160ee2a11c ("rsi: fill rx_params only once.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fixes to spelling mistakes in various files in rsi folder.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a \b (backspace) character in the message that wasn't intended.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a block of code that is indented at the wrong level. Fix this
with extra tabbing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During wowlan regression tests, sometimes radio is not waking up for wowlan
packet in coex mode. This is because of power save is enabled by default
in case of coex mode greater than one. Hence, disable power save in coex
mode to avoid radio loss.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We are redownloading the firmware after S4 restore and observed in
stress test that mac80211 sometimes gives power save request after
resume which causes the firmware in bad state. mac_ops_resumed flag
is added to skip that request until initialisation is done and Keeping
power save state is NONE.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At SDIO restore ieee80211_restart_hw() is getting called to restart all
MAC operations. This step is not required.
Returning 1 from mac80211_resume() will serve this purpose.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As we missed to detach HCI, while entering power off or hibernation,
an extra hci interface gets created whenever system is woken up, to
avoid this we added hci_detach() in rsi_disconnect(), rsi_freeze(),
and rsi_shutdown() functions which are invoked for these tests.
This patch fixes the issue
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a wowlan magic-packet has received to wake up the device, currently
driver is not taking care of what kind of packet has received. This patch
will add debug support for wakeup reason in driver.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
while inserting and removing sdio module multiple times, we are getting
sdhci warnings. This is because, improper assignment of ocr_avail value.
Fixed this by assigning proper value.
This patch is enhancement for commit 78e450719c ("rsi: Fix 'invalid
vdd' warning in mmc").
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the current approach of scanning, roaming delays are observed.
Firmware has support for back ground scanning. To get this advantage,
mac80211 hardware scan is implemented, which decides type of scan to
do based on connected state.
When station is in not connected, driver returns with special value 1
to trigger software scan in mac80211. In case of connected state,
background scan will be triggered.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in rsi_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
drivers/net/wireless/rsi/rsi_91x_mac80211.c:927:50: warning: address of
array 'key->key' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (vif->type == NL80211_IFTYPE_STATION && key->key &&
~~ ~~~~~^~~
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/136
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/rsi/rsi_91x_hal.c: In function 'rsi_send_data_pkt':
drivers/net/wireless/rsi/rsi_91x_hal.c:288:5: warning:
variable 'header_size' set but not used [-Wunused-but-set-variable]
'tx_params' only used for 'header_size' dereferenced,so also
can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During testing in ARM32 platforms, observed below kernel panic, as driver
accessing data beyond the allocated memory while submitting URB to USB.
Fix: Resolved this by specifying correct length by considering 64 bit
alignment. so that, USB bus driver will access only allocated memory.
Unit-test: Tested and confirm that driver bring up and scanning,
connection and data transfer works fine with this fix.
...skipping...
[ 25.389450] Unable to handle kernel paging request at virtual
address 5aa11422
[ 25.403078] Internal error: Oops: 5 [#1] SMP ARM
[ 25.407703] Modules linked in: rsi_usb
[ 25.411473] CPU: 1 PID: 317 Comm: RX-Thread Not tainted 4.18.0-rc7 #1
[ 25.419221] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 25.425764] PC is at skb_release_data+0x90/0x168
[ 25.430393] LR is at skb_release_all+0x28/0x2c
[ 25.434842] pc : [<807435b0>] lr : [<80742ba0>] psr: 200e0013 5aa1141e
[ 25.464633] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 25.477524] Process RX-Thread (pid: 317, stack limit = 0x(ptrval))
[ 25.483709] Stack: (0xedf69ed8 to 0xedf6a000)
[ 25.569907] Backtrace:
[ 25.572368] [<80743520>] (skb_release_data) from [<80742ba0>]
(skb_release_all+0x28/0x2c)
[ 25.580555] r9:7f00258c r8:00000001 r7:ee355000 r6:eddab0d0
r5:eddab000 r4:eddbb840
[ 25.588308] [<80742b78>] (skb_release_all) from [<807432cc>]
(consume_skb+0x30/0x50)
[ 25.596055] r5:eddab000 r4:eddbb840
[ 25.599648] [<8074329c>] (consume_skb) from [<7f00117c>]
(rsi_usb_rx_thread+0x64/0x12c [rsi_usb])
[ 25.608524] r5:eddab000 r4:eddbb840
[ 25.612116] [<7f001118>] (rsi_usb_rx_thread [rsi_usb]) from
[<80142750>] (kthread+0x11c/0x15c)
[ 25.620735] r10:ee9ff9e0 r9:edcde3b8 r8:ee355000 r7:edf68000
r6:edd3a780 r5:00000000
[ 25.628567] r4:edcde380
[ 25.631110] [<80142634>] (kthread) from [<801010e8>]
(ret_from_fork+0x14/0x2c)
[ 25.638336] Exception stack(0xedf69fb0 to 0xedf69ff8)
[ 25.682929] ---[ end trace 8236a5496f5b5d3b ]---
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables bss, wh and temp_flash_content are being assigned but are
never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'bss' set but not used [-Wunused-but-set-variable]
warning: variable 'wh' set but not used [-Wunused-but-set-variable]
warning: variable 'temp_flash_content' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
common->init_done flag should set after basic initialization. Hence,
moving init_done flag at end of rsi_91x_init().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rx_params are getting updated two times in driver, which is not required.
Hence, removing duplicate updation of rx_params from rsi_prepare_skb().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, RSI_NEEDED_HEADROOM is '80' for rsi driver, which is wrong.
As per rsi internal frame format, the RSI_NEEDED_HEADROOM shall be '84',
which is 64(dword_align) + 4(extended_desc) + 16(frame_desc).
Hence, corrected the needed headroom.
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, AP mode will work on only WLAN alone firmware. To give support
for AP and BT dual mode, adding firmware entry in 'struct ta_metadata'.
The firmware entry is based on what coex_mode is used in driver and coex
mode '4' for all AP+BT related functionalities. Hence, added the same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
while cleaning up the driver, observed that flash_content pointer is not
necessary in rsi_load_firmware(). Instead of this, driver can use
'fw_entry->data' directly.Hence, removed redundant flash_content pointer.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing redundant device id's from both usb and sdio idtables, as rsi
driver currently supporting only one module(RS9113). Also, replaced ids
with specific defines.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to multiple calls of add interface routine, vif is getting duplicated
and at certain instance, we are out of vifs, causing the driver to behave
abnormal.
Fix: Every vif has a unique mac-id, when we got a vif with same mac-id as
the previous id's, we will override the respective vif.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
System is unable to wake-up through magic-packet in secured connections.
Because key descriptor is getting corrupted and firmware is unable to
decrypt the magic packet. Fixed the issue by properly preparing it
before sending it to firmware.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Radio capabilities packet is not prepared properly for 40MHZ case,
ppe_ack_rate is a two byte variable which is initialized wrongly,
hence we are unable to connect, resolved by assigning it properly.
Signed-off-by: Ganapathi Raju <ganapathi.kondraju@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
observed low throughput rates during verification. This is because, QoS
enable flag is overridden by sequence number in the data descriptor frame.
Hence, added the fix for same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in rsi_dbg message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Auto rate table sent to firmware is getting corrupted
as memset to zeros is not done. Added memset to skb
data before filling auto rate table.
Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Observed crash in some scenarios when assertion has occurred,
this is because hw structure is freed and is tried to get
accessed in some functions where null check is already
present. So, avoided the crash by making the hw to NULL after
freeing.
Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As wowlan enable flag did not set, while writing wowlan parameters to
card using rsi_send_vap_dynamic_update, which results firmware is unable to
set wowlan configurations. Hence, setting wowlan flag before sending
parameters.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In coex mode, observed hibernate resume is not working properly, as the
hibernate_resume flag is not getting reset in rsi_coex_recv_pkt(),
when common card ready indication received from firmware. Hence resetting
hibernate_resume flag in this function.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the "poweroff" command is executed after wowlan enabled, we have
observed a system crash. In the system "poweroff" sequence, network-manager
is sent to inactive state by cleaning up the network interfaces, using
rsi_mac80211_remove_interface() and when driver tries to access those
network interfaces in rsi_wowlan_config() which was invoked by SDIO
shutdown, results in a crash. Added a NULL check before accessing the
network interfaces in rsi_wowlan_config().
Signed-off-by: Sanjay Kumar Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in rsi_dbg debug message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a potential execution path in which variable ret is returned
without being properly initialized previously.
Fix this by storing the value returned by function
rsi_usb_master_reg_write into _ret_.
Addresses-Coverity-ID: 1468407 ("Uninitialized scalar variable")
Fixes: 16d3bb7b2f ("rsi: disable fw watchdog timer during reset")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function rsi_hal_key_config returns before reaching code at line
922 if (status), hence this code is structurally dead.
Fix this by storing the value returned by rsi_hal_load_key
into _status_ for its further evaluation and use.
Addresses-Coverity-ID: 1468409 ("Structurally dead code")
Fixes: 4fd6c4762f ("rsi: roaming enhancements")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently 5GHz gets advertised even for the device which supports
only 2.4Ghz band. This patch fixes the issue
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power save is by default enabled for WLAN and BT coex mode.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently TID is extracted by checking at specific offset in data frame.
This approach doesn't work for some of the frames. This patch uses mac80211
API and do it correctly
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maximum number of supported aggregation subframes has been increased
to 8. This is the optimal number for the driver.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power save request should be sent on station interface. Virtual
interface which is connected should be preferred. This patch
resolves device not entering power save problem in certain
situations
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some device configuration flags need to be enabled while sending 'bootup
params' internal frame to firmware. This patch takes care of it.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware's watchdog timer should be disabled as a part of reset
sequence. This change fixes a firmware hang issue observed during
stress tests.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The issue here is that we allocate "data" and then set
"data = PTR_ALIGN(data, 8);" and then we free the aligned pointer
instead of the original pointer.
kmalloc() pointers are already ARCH_SLAB_MINALIGN aligned which is 8 or
more on everything except certain Xtensa variants. We decided that if
the Xtensa people ever notice a bug here then we'll tell them the bug is
on their side. ;)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support roaming below changes are done:
* Station notify frame is send to firmware after sending assoc
request. This will avoid dropping of first EAPOL frame due to
delay in creation of station control block in firmware.
* Data queues are unblocked after sending station notify in open
mode, after configuring key in WEP mode, and after receiving
EAPOL4 confirm in WPA mode.
* Initial EAPOL frames priority is chaged to MGMT, rekey EAPOL
frames priority changed to VO.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
80MHz clock for device should be enabled by default in
TX command frame radio capabilities.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Descriptors preparation is moved to core instead of HAL to
avoid synchronization issues in sending TX frames
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All descriptor structures are in rsi_mgmt.h except this
extended descriptor structure. Hence moving it to rsi_mgmt.h
and also renaming to rsi_xtend_desc.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable buffer_size is re-assigned the same value, this duplicated
assignment is redundant and can be removed.
Cleans up clang warning:
drivers/net/wireless/rsi/rsi_91x_usb.c:140:4: warning: Value stored
to 'buffer_size' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.
Currently rsi code uses a VLA based on a function argument to
`rsi_sdio_load_data_master_write()`. The function call chain is
Both these functions
rsi_sdio_reinit_device()
rsi_probe()
start the call chain:
rsi_hal_device_init()
rsi_load_fw()
auto_fw_upgrade()
ping_pong_write()
rsi_sdio_load_data_master_write()
[Without familiarity with the code] it appears that none of the 4 locks
mutex
rx_mutex
tx_mutex
tx_bus_mutex
are held when `rsi_sdio_load_data_master_write()` is called. It is therefore
safe to use kmalloc with GFP_KERNEL.
We can avoid using the VLA by using `kmalloc()` and free'ing the memory on all
exit paths.
Change buffer from 'u8 array' to 'u8 *'. Call `kmalloc()` to allocate memory for
the buffer. Using goto statement to call `kfree()` on all return paths.
It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc()` however this code is only called on initialization
(and re-initialization) so this overhead should not degrade performance.
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The linkage between the bluetooth driver and the wireless
driver is not defined properly, leading to build problems
such as:
warning: (BT_HCIRSI) selects RSI_COEX which has unmet direct dependencies (NETDEVICES && WLAN && WLAN_VENDOR_RSI && BT_HCIRSI && RSI_91X)
drivers/net/wireless/rsi/rsi_91x_main.o: In function `rsi_read_pkt':
(.text+0x205): undefined reference to `rsi_bt_ops'
As the dependency is actually the reverse (RSI_91X uses
the BT_RSI driver, not the other way round), this changes
the dependency to match, and enables the bluetooth driver
from the RSI_COEX symbol.
Fixes: 38aa4da504 ("Bluetooth: btrsi: add new rsi bluetooth driver")
Acked-by; Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lots of the wireless driver vendor Kconfig symol help text says
"questions about cards." (2 spaces between "about" and "cards")
Besides dropping one of those spaces, it also needs some other word
inserted there. Instead of putting each vendor's name there, I chose
to say "these" cards in all of the Kconfig help text.
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Curretly, RX packet processing is done sequencially. To improve
the efficiency, RX skb queue is introduced.
Here, while preparing RX URB skb is allocated and used
for RX buffer. When rx done handler is called, enqueue the skb
to rx_q and set the thread event.
RX thread is modified to dequeue packets from skb queue and
process further.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently 2 RX control blocks are allocated by default.
If wifi alone mode is used rx control block 2 is unusable.
So, changes are done accordingly in all places to use
RX control blocks dynamically based on coex mode check.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, RX packets are handled in interrupt context in SDIO
interface. To improve the efficiency of processing RX packets,
RX thread and RX skb queues are introduced.
When the packet is read from device, driver prepares skb, add to
RX queue and trigger RX thread event. RX thread processes the
packets from RX queue.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Queue number is correctly updated for BT traffic. Also, kzalloc
instead of kmalloc is used for Rx packet allocation.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Operating mode determines the support for other protocols.
This is made as module parameter for better usage.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BT frames are passed through coex and hal modules to BUS.
After firmware is loaded, based on the operating mode CARD
READY frame comes for each protocol. When BT card ready is
received, BT attach is called.
Protocol operations are exchanged between the modules
at initialization time.
Build flag CONFIG_RSI_COEX is introduced to enable coex support
if CONFIG_BT_RSIHCI is enabled. Coex operations are valid if
coex mode is greater than 1 only.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With BT support, driver has to handle two streams of data
(i.e. wlan and BT). Actual coex implementation is in firmware.
Coex module just schedule the packets to firmware by taking them
from the corresponding paths.
Structures for module and protocol operations are introduced for
this purpose. Protocol operations structure is global structure
which can be shared among different modules. Move initialization
of coex and operating mode values to rsi_91x_init().
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The common parameters used by wlan and bt modules are add
to a new header file "rsi_91x.h" defined in 'include/net'
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx bluetooth endpoint shall be added in further patches. Rx control
block is introduced here to handle Rx packets properly. Separate
function is written to initialize the RX control blocks.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the cases where len is too long, the error return path fails to
kfree allocated buffers buf and usb_reg_buf. The simplest fix is to
perform the sanity check on len before the allocations to avoid having
to do the kfree'ing in the first place.
Detected by CoverityScan, CID#1452258,1452259 ("Resource Leak")
Fixes: 59f73e2ae1 ("rsi: check length before USB read/write register")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"INVALID_STATE" is already being returned in the default case and this
code cannot be reached.
Addresses-Coverity-ID: 1398384
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
=MvWY
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some wowlan related code was outside CONFIG_PM flag which caused these
build errors. They are fixed by moving that code under CONFIG_PM flag.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ef71ed0608c ("rsi: sdio: Add WOWLAN support for S5 shutdown state")
Fixes: a24e35fcee0 ("rsi: sdio: Add WOWLAN support for S4 hibernate state")
Fixes: e1ced6422a3 ("rsi: sdio: add WOWLAN support for S3 suspend state")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is generic. It doesn't contain wowlan specific code.
It should not be under CONFIG_PM. This patch resolves compilation
errors observed when CONFIG_PM flag is disabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ef71ed0608c ("rsi: sdio: Add WOWLAN support for S5 shutdown state")
Fixes: a24e35fcee0 ("rsi: sdio: Add WOWLAN support for S4 hibernate state")
Fixes: e1ced6422a3 ("rsi: sdio: add WOWLAN support for S3 suspend state")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
