PTP hardware block can be configured to utilize
the external clock. Also the current ptp timestamp
can be captured when external trigger is applied on
a gpio pin. These features are required in scenarios
like connecting a external timing device to the chip
for time synchronization. The timing device provides
the clock and trigger(PPS signal) to the PTP block.
This patch does the following:
1. configures PTP block to use external clock
frequency and timestamp capture on external event.
2. sends PTP_REQ_EXTTS events to kernel ptp phc susbsytem
with captured timestamps
3. aligns PPS edge to adjusted ptp clock in the ptp device
by setting the PPS_THRESH to the reminder of the last
timestamp value captured by external PPS
Signed-off-by: Yi Guo <yig@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input clock frequency of PTP block is figured
out from hardware reset block currently. The firmware
data already has this info in sclk. Hence simplify
ptp driver to use sclk from firmware data.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC on CN10K support hardware timestamping such that 8 bytes addition
header is prepended to incoming packets. This patch does necessary
configuration to enable Hardware time stamping upon receiving request
from PF netdev interfaces.
Timestamp configuration is different on MAC (CGX) Octeontx2 silicon
and MAC (RPM) OcteonTX3 CN10k. Based on silicon variant appropriate
fn() pointer is called. Refactor MAC specific mbox messages to remove
unnecessary gaps in mboxids.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving ptp config request from netdev interface , Octeontx2 MAC
block CGX is configured to append timestamp to every incoming packet
and NPC config is updated with DMAC offset change.
Currently this configuration is not reset in FLR handler. This patch
resets the same.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink is fully
configured. This change allows us to delete call to devlink_params_publish()
and impossible check during unregister flow.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimized KPU1 entry processing for variable-length custom L2 headers
of size 24B, 90B by
- Moving LA LTYPE parsing for 24B and 90B headers to PKIND.
- Removing LA flags assignment for 24B and 90B headers.
- Reserving a PKIND 55 to parse variable length headers.
Also, new mailbox(NPC_SET_PKIND) added to configure PKIND with
corresponding variable-length offset, mask, and shift count
(NPC_AF_KPUX_ENTRYX_ACTION0).
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With current KPU profile, while parsing GTPU packets, GTPU payload
is also being parsed and GTPU PDU payload is being treated as IPV4
data, which is not correct. In case of GTPU packets, parsing should
be stopped after identifying the GTPU. Adding changes to limit KPU
profile parsing for GTPU payload.
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com> # dsa
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per HW errata AQ modification to CQ could be discarded on heavy
traffic. This patch implements workaround for the same after each
CQ write by AQ check whether the requested fields (except those
which HW can update eg: avg_level) are properly updated or not.
If CQ context is not updated then perform AQ write again.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable blkaddr is being initialized with a value that is never
read, it is being updated later on in a for-loop. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where the condition !is_rvu_otx2(rvu) is false variable
val is not initialized and can contain a garbage value. Fix this by
initializing val to zero and bit-wise or'ing in BIT_ULL(51) to val
for the true condition case of !is_rvu_otx2(rvu).
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 4b5a3ab17c ("octeontx2-af: Hardware configuration for inline IPsec")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On OcteonTX2/CN10K SoC, the admin function (AF) is the only one
with all priviliges to configure HW and alloc resources, PFs and
it's VFs have to request AF via mailbox for all their needs.
This patch adds new mailbox messages for CPT PFs and VFs to configure
HW resources for inline-IPsec.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Vidya Sagar Velumuri <vvelumuri@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K MAC block (RPM) differs in number of stats compared to Octeontx2
MAC block (CGX). RPM supports stats for each class of PFC and error
packets etc. It would be difficult for user to read stats from ethtool
and map to their definition.
New debugfs file is already added to read RPM stats along with their
definition. This patch adds proper checks such that RPM stats will not
be part of ethtool.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocated before 'lmac' is stored in 'cgx->lmac_idmap[]' must be
freed explicitly. Otherwise, in case of error, it will leak.
Rename the 'err_irq' label to better describe what is done at this place in
the error handling path.
Fixes: 6f14078e3e ("octeontx2-af: DMAC filter support in MAC block")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to match 'rvu_alloc_bitmap()', add a 'rvu_free_bitmap()' function
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reserves the LMTST lines per cpu instead
of separate LMTST lines for NPA(buffer free) and NIX(sqe flush).
LMTST line of the core on which SQ or RQ is processed is used
for LMTST operation.
This patch also replace STEOR with STEORL release semantics and
updates driver name in ethtool file.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check one more time before exiting the API with an error.
Fix API to poll at least twice, in case there are other high priority
tasks and this API doesn't get CPU cycles for multiple jiffies update.
In addition, increase timeout from usecs_to_jiffies(10000) to
usecs_to_jiffies(20000), to prevent the case that for CONFIG_100HZ
timeout will be a single jiffies.
A single jiffies results actual timeout that can be any time between
1usec and 10msec. To solve this, a value of usecs_to_jiffies(20000)
ensures that timeout is 2 jiffies.
Signed-off-by: Smadar Fuks <smadarf@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With current config, for packets with IPv4 checksum errors,
errorcode is being set to UNKNOWN. Hence added a separate
errorcodes for outer and inner IPv4 checksum and changed
NPC configuration accordingly.
Also turn on L2 multicast address check in NPC protocol check block.
Fixes: 6b3321bacc ("octeontx2-af: Enable packet length and csum validation")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the static code analyzer reported issues
in rvu_npc.c. The reported errors are different sizes of
operands in bitops and returning uninitialized values.
Fixes: 651cd26523 ("octeontx2-af: MCAM entry installation support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In npc_update_vf_flow_entry function the loop cursor
'index' is being changed inside the loop causing
the loop to spin forever. This in turn hogs the kworker
thread forever and no other mbox message is processed
by AF driver after that. Fix this by using
another variable in the loop.
Fixes: 55307fcb92 ("octeontx2-af: Add mbox messages to install and delete MCAM rules")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the given counter does not belong to the entry
then code ends up in infinite loop because the loop
cursor, entry is not getting updated further. This
patch fixes that by updating entry for every iteration.
Fixes: a958dd59f9 ("octeontx2-af: Map or unmap NPC MCAM entry and counter")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For better performance set hardware to use NDC TX for reading packet
data specified NIX_SEND_SG_S.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NPC extraction profile marks layer types
NPC_LT_LB_CTAG for CTAG and NPC_LT_LB_STAG_QINQ for
STAG after parsing input packet. Those layer types
can be used to install ntuple filters using
vlan-etype option. Below are the commands and
corresponding behavior with this patch in place.
> alias nt "ethtool -U eth0 flow-type ether"
> nt vlan 5 m 0xf000 action 0
Input packets with outer VLAN id as 5 i.e,
stag packets with VLAN id 5 and ctag packets with
VLAN id as 5 are hit.
> nt vlan-etype 0x8100 action 0
All input ctag packets with any VLAN id are hit.
> nt vlan-etype 0x88A8 action 0
All input stag packets with any VLAN id are hit.
> nt vlan-etype 0x8100 vlan 5 m 0xf000 action 0
All input ctag packets with VLAN id 5 are hit.
> nt vlan-etype 0x88A8 vlan 5 m 0xf000 action 0
All input stag packets with VLAN id 5 are hit.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed inconsistent license text across the RVU admin
function driver.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed inconsistent license text across the netdev
drivers.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhancing the mailbox scope to support important configurations
like enabling scheduled LMTST, disable LMTLINE prefetch, disable
early completion for ordered LMTST, as per request from the
application. On FLR these configurations will be reset to default.
This patch also adds the 95XXO silicon version to octeontx2 silicon
list.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If otx2_mbox_get_rsp() fails, otx2_set_flowkey_cfg() need return an
error code.
Fixes: e793836545 ("octeontx2-pf: Fix algorithm index in MCAM rules with RSS action")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added mbox for PF/VF drivers to retrieve current ingress bandwidth
profile free count. Also added current policer timeunit
configuration info based on which ratelimiting decisions can be
taken by PF/VF drivers.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New usecases are popping up where in user wants to install common MCAM
filters for all interfaces. Having channel verification will result in
duplicating such MCAM filters for each of the ingress interface. Hence
removed channel verification.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K slicon has different device id for PTP device.
Hence this patch updates the driver with new id.
Though ptp driver being a separate driver AF manages
configuring PTP block by all PFs. To manage ptp, AF
driver checks in its probe whether
1. ptp hardware device found on silicon
2. A driver is bound to ptp device
3. The ptp driver probe is successful
In failure of cases 1 and 3, AF proceeds with out ptp
and for case 2 defers the probe. This patch refactors
code also to check for all the PTP device ids given in
ptp device ids table for case 1.
Also added PTP device ID for 95O silicon
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving the MBOX_MSG_FREE_RSRC_CNT, the AF will find out the
current number of free resources and reply it back to the requester. No
guarantee is given on the future state of the free resources yet.
If another requester sends MBOX_MSG_ATTACH_RESOURCES after this call,
the number of available resources might change.
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for packet IO via SDK links which is used when
Octeon is connected as a end-point. Traffic host to end-point
and vice versa flow through SDP links. This patch also support
dual SDP blocks supported in 98xx silicon.
Signed-off-by: Radha Mohan Chintakuntla <radhac@marvell.com>
Signed-off-by: Nalla Pradeep <pnalla@marvell.com>
Signed-off-by: Subrahmanyam Nilla <snilla@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 98xx, there are 2 NIX blocks and 4 LBK blocks present. The way
these NIX-LBK should be configured depends on the use case. By
default loopback functionality is supported in AF VF pairs which
are attached to NIX0 and NIX1 LFs alternatively to ensure load
balancing. NIX0 transmits a packet to LBK1 which will be received
by NIX1 and packet transmitted by NIX1 will get received by NIX0 via
LBK2.
There are some requirements where only one AF VF is used and respective
NIX is expected to operate in a mode where it can receive it own packet
back. This can be achieved if NIX0 sends packet to LBK0 and not LBK1.
Adding a flag in LF alloc request mailbox which can setup NIX0 to use
LBK0 and NIX1 can use LBK3.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike OcteonTx2, the channel numbers used by CGX/RPM
and LBK on CN10K silicons aren't fixed in HW. They are
SW programmable, hence we cannot derive transmit link
from static channel numbers anymore. Get the same from
admin function via mailbox.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before C0 HW revision, The RSS adder was computed based the
following static formula.
rss_adder<7:0> = flow_tag<7:0> ^ flow_tag<15:8> ^
flow_tag<23:16> ^ flow_tag<31:24>
The above scheme has the following drawbacks:
1) It is not in line with other standard NIC behavior.
2) There can be an SW use case where SW can compute the hash
upfront using Toeplitz function and predict the queue selection
to optimize some packet lookup function. The nonstandard
way of doing XOR makes the consumer to not predict the queue selection.
C0 HW revision onwards, The HW can configure the
rss_adder<7:0> as flow_tag<7:0> to align with standard NICs.
This patch adds an option to select legacy RSS adder mode
vs standard NIC behavior by setting NIX_LF_RSS_TAG_LSB_AS_ADDER flag.
Since this bit field is used as reserved in old HW revisions,
No need to have an additional HW version check.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from 96xx C0 onwards all silicons support traffic shaping.
This patch enables that feature along with other changes
- When PIR/CIR shaping config is modified, toggle SW_XOFF
for config to take effect
- Before SMQ flush, clear SW_XOFF at all parent schedulers
- Support to read current transmit scheduler configuration via mbox
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIX_AF_TX_LINKX_NORM_CREDIT holds running counter of
tx credits available per link. But, tx credits should be
configured based on MTU config. So MTU change needs tx
credit count update.
An issue exists whereby when both PF & VF are enabled and
PF traffic is flowing, if VF requests for MTU update,
updating the NORM_CREDIT register will lead to corruption
of credit count and subsequent deadlock of tx link as
the NORM_CREDIT register holds running count.
This patch provides workaround by pausing link traffic
using NIX_AF_TL1X_SW_XOFF, waiting for existing packets to
drain, and used credits be returned before updating new
credit count.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear and disable interrupt before queueing work as there might be
a chance that work gets completed on other core faster and
interrupt enable as a part of the work completes before
interrupt disable in the interrupt context. This leads to
permanent disable of interrupt.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set NPA batch allocation engine to process 35 cache lines
per turn on CN10k platform.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RVU SMMU widget stores the final translated PA at
RVU_AF_SMMU_TLN_FLIT0<57:18> instead of FLIT1 register. This patch
fixes the address translation logic to use the correct register.
Fixes: 893ae97214 ("octeontx2-af: cn10k: Support configurable LMTST regions")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherthan setting action as RSS in NPC MCAM entry, RSS flowkey
algorithm index also needs to be set. Otherwise whatever algorithm
is defined at flowkey index '0' will be considered by HW and pkt
flows will be distributed as such.
Fix this by saving the flowkey index sent by admin function while
initializing RSS and then use it when framing MCAM rules.
Fixes: 81a4362016 ("octeontx2-pf: Add RSS multi group support")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever user changes interface MAC address both default DMAC based
MCAM rule and VLAN offload (for strip) rules are updated with new
MAC address. To update or install VLAN offload rule PF driver needs
interface's receive channel info, which is retrieved from admin
function at the time of NIXLF initialization.
If user changes MAC address before interface is UP, VLAN offload rule
installation will fail and throw error as receive channel is not valid.
To avoid this, skip VLAN offload rule installation if netdev is not UP.
This rule will anyway be reinslatted as part of open() call.
Fixes: fd9d7859db ("octeontx2-pf: Implement ingress/egress VLAN offload")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bandwidth profiles (ipolicer structure)is implemented only on CN10K
platform. But current code try to free the ipolicer memory without
checking the capibility flag leading to driver crash on OCTEONTX2
platform. This patch fixes the issue by add capability flag check.
Fixes: e8e095b3b3 ("octeontx2-af: cn10k: Bandwidth profiles config support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K platform requires physically contiguous memory for LMTST
operations which goes beyond a single page. Not having physically
contiguous memory will result in HW fetching transmit descriptors from
a wrong memory location.
Hence use DMA_ATTR_FORCE_CONTIGUOUS attribute while allocating
LMTST regions.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the erroneous vlan priority mask field that was
send to npc_install_flow_req.
Fixes: 1d4d9e42c2 ("octeontx2-pf: Add tc flower hardware offload on ingress traffic")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported link modes are updated by firmware in shared
structure per interface. Kernel uses this value to display
supported link modes via ethtool.
Currently there is extra validation that firmware updated
modes are validated against internal list of supported modes.
As intenal list of supported modes are not updated frequently
new modes supported by firmware are not updated to ethtool.
Hence remove extra validation and report all firmware updated
modes.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print debug message if any of the RVU hardware blocks
reset fails.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per hardware the base channel number configured
for programmable channels of a block must be multiple
of number of channels of that block. This condition
is not met for SDP base channel currently. Hence this
patch ensures all the base channel numbers of all
blocks are multiple of number of channels present in
the blocks. Also instead of hardcoding SDP number
of channels the same is read from the NIX_AF_CONST1
register.
Fixes: 242da43921 ("octeontx2-af: cn10k: Add support for programmable")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'bp_ena' in Aura context is NIX block index, setting it
zero will always backpressure NIX0 block, even if NIXLF
belongs to NIX1. Hence fix this by setting it appropriately
based on NIX block address.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that mcam flows are allocated
before adding or destroying the flows.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change added error checking messages and failed to remove one
of the previous error checks. There are now two checks on variable err
so the second one is redundant dead code and can be removed.
Addresses-Coverity: ("Logically dead code")
Fixes: a83bdada06 ("octeontx2-af: Add debug messages for failures")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210818130927.33895-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VLAN TCI is a 16 bit field which includes Priority(3 bits),
CFI(1 bit) and VID(12 bits). Currently ntuple filters support
installing rules to steer packets based on VID only.
This patch extends that support such that filters can
be installed for entire VLAN TCI.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On CN10K, the higher bits in the channel number represents the CPT
channel number. Mask out these higher bits in the npc configuration
to allow packets from cpt for parsing.
Signed-off-by: Vidya <vvelumuri@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way SW can identify the number NPC counters supported by silicon
has changed for CN10K. This patch addresses this reading appropriate
registers to find out number of counters available.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mcam entry allocation request is from PF
and NOT a priority allocation request then allocate
low priority entries so that PF entries always have
lower priority than its VFs. This is required so
that entries with (base) MCAM match criteria have lower
priority compared to entries with (base + additional)
match criteria. This patch considers only best case
scenario where PF entries are allocated from low
priority zone if low priority zone has free space.
There are worst case scenarios like:
1. VFs allocating hundreds of MCAM entries leading to VFs
using all mid priority zone and low priority zone entries
hence no entries free from low priority zone for PF.
2. All the PFs and VFs in the system allocating and freeing
entries causing fragmentation in MCAM space and all the
entries requested by PF could not fit in low priority
zone for allocation.
This patch do not handle worst case scenarios.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for setting or modifying MCAM entry count at
runtime via devlink params.
commands:
devlink dev param show
pci/0002:02:00.0:
name mcam_count type driver-specific
values:
cmode runtime value 16
devlink dev param set pci/0002:02:00.0 name mcam_count
value 64 cmode runtime
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables used for TC flow management like maximum number
of flows, number of flows installed etc are a copy of ntuple
flow management variables. Since both TC and NTUPLE are not
supported at the same time, it's better to unify these with
common variables.
This patch addresses this unification and also does cleanup of
other minor stuff wrt TC.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per single mailbox request a maximum of 256 MCAM entries
can be allocated. If more than 256 are being allocated, then
the mcam indices in the final list could get jumbled. Hence
sort the indices.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet flow classification support for both LMAC mapped virtual
functions and loopback VFs. This patch adds supports for ntuple
offload feature.
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabled NETIF_F_RXALL support for VF driver.
Also removed MTU range comments which are no longer valid.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added debug messages for various failures during probe.
This will help in quickly identifying the API where the failure
is happening.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add appropriate error codes to be used when returning from AF
mailbox handlers due to some error condition.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When installing a flow using npc_install_flow
mailbox there are number of reasons to reject
the request like caller is not permitted,
invalid channel specified in request, flow
not supported in extraction profile and so on.
Hence define new error codes for npc flows and use
them instead of generic error codes.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All kernel devlink implementations call to devlink_alloc() during
initialization routine for specific device which is used later as
a parent device for devlink_register().
Such late device assignment causes to the situation which requires us to
call to device_register() before setting other parameters, but that call
opens devlink to the world and makes accessible for the netlink users.
Any attempt to move devlink_register() to be the last call generates the
following error due to access to the devlink->dev pointer.
[ 8.758862] devlink_nl_param_fill+0x2e8/0xe50
[ 8.760305] devlink_param_notify+0x6d/0x180
[ 8.760435] __devlink_params_register+0x2f1/0x670
[ 8.760558] devlink_params_register+0x1e/0x20
The simple change of API to set devlink device in the devlink_alloc()
instead of devlink_register() fixes all this above and ensures that
prior to call to devlink_register() everything already set.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Program SQ, MDQ, TL4 to TL2 transmit scheduler queues' DWRR
weight based on DWRR MTU programmed at NIX_AF_DWRR_RPM_MTU.
The DWRR MTU from admin function is retrieved via mbox.
On OcteaonTx2 silicon, admin function driver responds with DWRR
MTU as '1'. This helps to avoid silicon specific transmit
scheduler DWRR quantum/weight configuration logic.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On OcteonTx2 DWRR quantum is directly configured into each of
the transmit scheduler queues. And PF/VF drivers were free to
config any value upto 2^24.
On CN10K, HW is modified, the quantum configuration at scheduler
queues is in terms of weight. And SW needs to setup a base DWRR MTU
at NIX_AF_DWRR_RPM_MTU / NIX_AF_DWRR_SDP_MTU. HW will do
'DWRR MTU * weight' to get the quantum. For LBK traffic, value
programmed into NIX_AF_DWRR_RPM_MTU register is considered as
DWRR MTU.
This patch programs a default DWRR MTU of 8192 into HW and also
provides a way to change this via devlink params.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIX_RX_SW_SYNC ensures all existing transactions are finished and
pkts are written to LLC/DRAM, queues should be teared down after
successful SW_SYNC. Due to a HW errata, in some rare scenarios
an existing transaction might end after SW_SYNC operation. To
ensure operation is fully done, do the SW_SYNC twice.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid configure backpressure for LBK links as they
don't support it and enable lmacs before configuration
pause frames.
Fixes: 75f3627099 ("octeontx2-pf: Support to enable/disable pause frames via ethtool")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the existing code while changing the number of TX/RX
queues using ethtool the PF/VF interface resources are
freed and reallocated (otx2_stop and otx2_open is called)
if the device is in running state. If any resource allocation
fails in otx2_open, driver free already allocated resources
and return. But again, when the number of queues changes
as the device state still running oxt2_stop is called.
In which we try to free already freed resources leading
to driver crash.
This patch fixes the issue by setting the INTF_DOWN flag on
error and free the resources in otx2_stop only if the flag is
not set.
Fixes: 50fe6c02e5 ("octeontx2-pf: Register and handle link notifications")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PKINDs are not assigned to LBK channels.
The default value of LBK_CHX_PKIND (channel to PKIND mapping) register
is zero, which is resulting in a overlap of pkind between LBK and CGX
LMACs. When KPU1 parser config is modified when PTP timestamping is
enabled on the CGX LMAC interface it is impacting traffic on LBK
interfaces as well.
This patch fixes the issue by reserving the PKIND#0 for LBK devices.
CGX mapped PF pkind starts from 1 and also fixes the max pkind available.
Fixes: 421572175b ("octeontx2-af: Support to enable/disable HW timestamping")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the number of VFs of a PF correctly by calling
rvu_get_pf_numvfs in rvu_switch_disable function.
Also hwvf is not required hence remove it.
Fixes: 23109f8dd0 ("octeontx2-af: Introduce internal packet switching")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added mailbox id to name translation on trace entry for
better tracing output.
Before the change:
otx2_msg_process: [0002:01:00.0] msg:(0x03) error:0
After the change:
otx2_msg_process: [0002:01:00.0] msg:(DETACH_RESOURCES) error:0
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove devm_kfree of memory where VLAN entry to RVU PF mapping
info is saved. This will be freed anyway at driver exit.
Having this could result in warning from devm_kfree() if
the memory is not allocated due to errors in rvu_nix_block_init()
before nix_setup_txvlan().
Fixes: 9a946def26 ("octeontx2-af: Modify nix_vtag_cfg mailbox to support TX VTAG entries")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now any communication between CGXs PFs and
their VFs within the system is possible only by
external switches sending packets back to the
system. This patch adds internal switching support.
Broadcast packet replication is not covered here.
RVU admin function (AF) maintains MAC addresses
of all interfaces in the system. When switching is
enabled, MCAM entries are allocated to install rules
such that packets with DMAC matching any of the
internal interface MAC addresses is punted back
into the system via the loopback channel.
On the receive side the default unicast rules
are modified to not check for ingress channel.
So any packet with matching DMAC irrespective of
which interface it is coming from will be forwarded
to the respective PF/VF interface.
The transmit side rules and default unicast rules
are updated if user changes MAC address of an interface.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AF till now only manages the allocation and freeing of
MCAM rules for other PF/VFs in system. To implement
L2 switching between all CGX mapped PF and VFs, AF
requires MCAM entries for DMAC rules for each PF and VF.
This patch modifies AF driver such that AF can also
allocate MCAM rules and install rules for other
PFs and VFs. All the checks like channel verification
for RX rules and PF_FUNC verification for TX rules are
relaxed in case AF is allocating or installing rules.
Also all the entry and counter to owner mappings are
set to NPC_MCAM_INVALID_MAP when they are free indicating
those are not allocated to AF nor PF/VFs.
This patch also ensures that AF allocated and installed
entries are displayed in debugfs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For enabling VF-VF switching the packets egressing
out of CGX mapped VFs needed to be sent to LBK
so that same packets are received back to the system.
But the LBK link also needs to be enabled in addition
to a VF's mapped CGX_LMAC link otherwise hardware
raises send error interrupt indicating selected LBK
link is not enabled in NIX_AF_TL3_TL2X_LINKX_CFG register.
Hence this patch enables all LBK links in
TL3_TL2_LINKX_CFG registers.
Also to enable packet flow between PFs/VFs of NIX0
to PFs/VFs of NIX1(in 98xx silicon) the NPC TX DMAC
rules has to be installed such that rules must be hit
for any TX interface i.e., NIX0-TX or NIX1-TX provided
DMAC match creteria is met. Hence this patch changes the
behavior such that MCAM is programmed to match with any
NIX0/1-TX interface for TX rules.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - regressions:
- sock: fix parameter order in sock_setsockopt()
Current release - new code bugs:
- netfilter: nft_last:
- fix incorrect arithmetic when restoring last used
- honor NFTA_LAST_SET on restoration
Previous releases - regressions:
- udp: properly flush normal packet at GRO time
- sfc: ensure correct number of XDP queues; don't allow enabling the
feature if there isn't sufficient resources to Tx from any CPU
- dsa: sja1105: fix address learning getting disabled on the CPU port
- mptcp: addresses a rmem accounting issue that could keep packets
in subflow receive buffers longer than necessary, delaying
MPTCP-level ACKs
- ip_tunnel: fix mtu calculation for ETHER tunnel devices
- do not reuse skbs allocated from skbuff_fclone_cache in the napi
skb cache, we'd try to return them to the wrong slab cache
- tcp: consistently disable header prediction for mptcp
Previous releases - always broken:
- bpf: fix subprog poke descriptor tracking use-after-free
- ipv6:
- allocate enough headroom in ip6_finish_output2() in case
iptables TEE is used
- tcp: drop silly ICMPv6 packet too big messages to avoid
expensive and pointless lookups (which may serve as a DDOS
vector)
- make sure fwmark is copied in SYNACK packets
- fix 'disable_policy' for forwarded packets (align with IPv4)
- netfilter: conntrack: do not renew entry stuck in tcp SYN_SENT state
- netfilter: conntrack: do not mark RST in the reply direction coming
after SYN packet for an out-of-sync entry
- mptcp: cleanly handle error conditions with MP_JOIN and syncookies
- mptcp: fix double free when rejecting a join due to port mismatch
- validate lwtstate->data before returning from skb_tunnel_info()
- tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path
- mt76: mt7921: continue to probe driver when fw already downloaded
- bonding: fix multiple issues with offloading IPsec to (thru?) bond
- stmmac: ptp: fix issues around Qbv support and setting time back
- bcmgenet: always clear wake-up based on energy detection
Misc:
- sctp: move 198 addresses from unusable to private scope
- ptp: support virtual clocks and timestamping
- openvswitch: optimize operation for key comparison
-----BEGIN PGP SIGNATURE-----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=QFnb
-----END PGP SIGNATURE-----
Merge tag 'net-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski.
"Including fixes from bpf and netfilter.
Current release - regressions:
- sock: fix parameter order in sock_setsockopt()
Current release - new code bugs:
- netfilter: nft_last:
- fix incorrect arithmetic when restoring last used
- honor NFTA_LAST_SET on restoration
Previous releases - regressions:
- udp: properly flush normal packet at GRO time
- sfc: ensure correct number of XDP queues; don't allow enabling the
feature if there isn't sufficient resources to Tx from any CPU
- dsa: sja1105: fix address learning getting disabled on the CPU port
- mptcp: addresses a rmem accounting issue that could keep packets in
subflow receive buffers longer than necessary, delaying MPTCP-level
ACKs
- ip_tunnel: fix mtu calculation for ETHER tunnel devices
- do not reuse skbs allocated from skbuff_fclone_cache in the napi
skb cache, we'd try to return them to the wrong slab cache
- tcp: consistently disable header prediction for mptcp
Previous releases - always broken:
- bpf: fix subprog poke descriptor tracking use-after-free
- ipv6:
- allocate enough headroom in ip6_finish_output2() in case
iptables TEE is used
- tcp: drop silly ICMPv6 packet too big messages to avoid
expensive and pointless lookups (which may serve as a DDOS
vector)
- make sure fwmark is copied in SYNACK packets
- fix 'disable_policy' for forwarded packets (align with IPv4)
- netfilter: conntrack:
- do not renew entry stuck in tcp SYN_SENT state
- do not mark RST in the reply direction coming after SYN packet
for an out-of-sync entry
- mptcp: cleanly handle error conditions with MP_JOIN and syncookies
- mptcp: fix double free when rejecting a join due to port mismatch
- validate lwtstate->data before returning from skb_tunnel_info()
- tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path
- mt76: mt7921: continue to probe driver when fw already downloaded
- bonding: fix multiple issues with offloading IPsec to (thru?) bond
- stmmac: ptp: fix issues around Qbv support and setting time back
- bcmgenet: always clear wake-up based on energy detection
Misc:
- sctp: move 198 addresses from unusable to private scope
- ptp: support virtual clocks and timestamping
- openvswitch: optimize operation for key comparison"
* tag 'net-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (158 commits)
net: dsa: properly check for the bridge_leave methods in dsa_switch_bridge_leave()
sfc: add logs explaining XDP_TX/REDIRECT is not available
sfc: ensure correct number of XDP queues
sfc: fix lack of XDP TX queues - error XDP TX failed (-22)
net: fddi: fix UAF in fza_probe
net: dsa: sja1105: fix address learning getting disabled on the CPU port
net: ocelot: fix switchdev objects synced for wrong netdev with LAG offload
net: Use nlmsg_unicast() instead of netlink_unicast()
octeontx2-pf: Fix uninitialized boolean variable pps
ipv6: allocate enough headroom in ip6_finish_output2()
net: hdlc: rename 'mod_init' & 'mod_exit' functions to be module-specific
net: bridge: multicast: fix MRD advertisement router port marking race
net: bridge: multicast: fix PIM hello router port marking race
net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340
dsa: fix for_each_child.cocci warnings
virtio_net: check virtqueue_add_sgs() return value
mptcp: properly account bulk freed memory
selftests: mptcp: fix case multiple subflows limited by server
mptcp: avoid processing packet if a subflow reset
mptcp: fix syncookie process if mptcp can not_accept new subflow
...
In the case where act->id is FLOW_ACTION_POLICE and also
act->police.rate_bytes_ps > 0 or act->police.rate_pkt_ps is not > 0
the boolean variable pps contains an uninitialized value when
function otx2_tc_act_set_police is called. Fix this by initializing
pps to false.
Addresses-Coverity: ("Uninitialized scalar variable)"
Fixes: 68fbff68db ("octeontx2-pf: Add police action for TC flower")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when the call to otx2_mbox_alloc_msg_cgx_mac_addr_update fails
the error return variable rc is being assigned -ENOMEM and does not
return early. rc is then re-assigned and the error case is not handled
correctly. Fix this by returning -ENOMEM rather than assigning rc.
Addresses-Coverity: ("Unused value")
Fixes: 79d2be385e ("octeontx2-pf: offload DMAC filters to CGX/RPM block")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added option for per CPU threads to the hwlat tracer
- Have hwlat tracer handle hotplug CPUs
- New tracer: osnoise, that detects latency caused by interrupts, softirqs
and scheduling of other tasks.
- Added timerlat tracer that creates a thread and measures in detail what
sources of latency it has for wake ups.
- Removed the "success" field of the sched_wakeup trace event.
This has been hardcoded as "1" since 2015, no tooling should be looking
at it now. If one exists, we can revert this commit, fix that tool and
try to remove it again in the future.
- tgid mapping fixed to handle more than PID_MAX_DEFAULT pids/tgids.
- New boot command line option "tp_printk_stop", as tp_printk causes trace
events to write to console. When user space starts, this can easily live
lock the system. Having a boot option to stop just after boot up is
useful to prevent that from happening.
- Have ftrace_dump_on_oops boot command line option take numbers that match
the numbers shown in /proc/sys/kernel/ftrace_dump_on_oops.
- Bootconfig clean ups, fixes and enhancements.
- New ktest script that tests bootconfig options.
- Add tracepoint_probe_register_may_exist() to register a tracepoint
without triggering a WARN*() if it already exists. BPF has a path from
user space that can do this. All other paths are considered a bug.
- Small clean ups and fixes
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYN8YPhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhxLAP9Mo5hHv7Hg6W7Ddv77rThm+qclsMR/
yW0P+eJpMm4+xAD8Cq03oE1DimPK+9WZBKU5rSqAkqG6CjgDRw6NlIszzQQ=
=WEPR
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Added option for per CPU threads to the hwlat tracer
- Have hwlat tracer handle hotplug CPUs
- New tracer: osnoise, that detects latency caused by interrupts,
softirqs and scheduling of other tasks.
- Added timerlat tracer that creates a thread and measures in detail
what sources of latency it has for wake ups.
- Removed the "success" field of the sched_wakeup trace event. This has
been hardcoded as "1" since 2015, no tooling should be looking at it
now. If one exists, we can revert this commit, fix that tool and try
to remove it again in the future.
- tgid mapping fixed to handle more than PID_MAX_DEFAULT pids/tgids.
- New boot command line option "tp_printk_stop", as tp_printk causes
trace events to write to console. When user space starts, this can
easily live lock the system. Having a boot option to stop just after
boot up is useful to prevent that from happening.
- Have ftrace_dump_on_oops boot command line option take numbers that
match the numbers shown in /proc/sys/kernel/ftrace_dump_on_oops.
- Bootconfig clean ups, fixes and enhancements.
- New ktest script that tests bootconfig options.
- Add tracepoint_probe_register_may_exist() to register a tracepoint
without triggering a WARN*() if it already exists. BPF has a path
from user space that can do this. All other paths are considered a
bug.
- Small clean ups and fixes
* tag 'trace-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (49 commits)
tracing: Resize tgid_map to pid_max, not PID_MAX_DEFAULT
tracing: Simplify & fix saved_tgids logic
treewide: Add missing semicolons to __assign_str uses
tracing: Change variable type as bool for clean-up
trace/timerlat: Fix indentation on timerlat_main()
trace/osnoise: Make 'noise' variable s64 in run_osnoise()
tracepoint: Add tracepoint_probe_register_may_exist() for BPF tracing
tracing: Fix spelling in osnoise tracer "interferences" -> "interference"
Documentation: Fix a typo on trace/osnoise-tracer
trace/osnoise: Fix return value on osnoise_init_hotplug_support
trace/osnoise: Make interval u64 on osnoise_main
trace/osnoise: Fix 'no previous prototype' warnings
tracing: Have osnoise_main() add a quiescent state for task rcu
seq_buf: Make trace_seq_putmem_hex() support data longer than 8
seq_buf: Fix overflow in seq_buf_putmem_hex()
trace/osnoise: Support hotplug operations
trace/hwlat: Support hotplug operations
trace/hwlat: Protect kdata->kthread with get/put_online_cpus
trace: Add timerlat tracer
trace: Add osnoise tracer
...
DMAC filtering can be achieved by either NPC MCAM rules or
CGX/RPM MAC filters. Currently we are achieving this by NPC
MCAM rules. This patch offloads DMAC filters to CGX/RPM MAC
filters instead of NPC MCAM rules. Offloading DMAC filter to
CGX/RPM block helps in reducing traffic to NPC block and
save MCAM rules
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC block supports 32 dmac filters which are logically
divided among all attached LMACS.
For example MAC block0 having one LMAC then maximum supported
filters are 32 where as MAC block1 having 4 enabled LMACS
them maximum supported filteres are 8 for each LMAC.
This patch adds mbox handlers to add/delete/update mac entry
in DMAC filter table.
Signed-off-by: Sunil Kumar Kori <skori@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver uses static LMTST region allocated by firmware.
This memory gets populated as PF/VF BAR2. RVU PF/VF driver ioremap
the memory as device memory for NIX/NPA operation. Since the memory
is mapped as device memory we see performance degration. To address
this issue this patch implements runtime memory allocation.
RVU PF/VF allocates memory during device probe and share the base
address with RVU AF. RVU AF then configure the LMT MAP table
accordingly.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the lmtst_tbl_setup_req mbox to support run time
LMTST configuration.
RVU PF/VF and DPDK/ODP allocates a LMT region, creates a translation
entry for a device via VFIO IOCTLs.
This IOVA is shared with AF through above mbox. AF then uses
RVU_SMMU transulation Widget and gets PA for the IOVA and updates
the LMTtable entry for that device.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing a new mailbox to support updating lmt entries
and common lmt base address scheme i.e. multiple pcifuncs
can share lmt region to reduce L1 cache pressure for application.
Parameters passed to mailbox includes the primary pcifunc
value whose lmt regions will be shared by other secondary
pcifuncs. Here secondary pcifunc will be the one who is
calling the mailbox.
For example:
By default each pcifunc has its own LMT base address:
PCIFUNC1 LMT_BASE_ADDR A
PCIFUNC2 LMT_BASE_ADDR B
PCIFUNC3 LMT_BASE_ADDR C
PCIFUNC4 LMT_BASE_ADDR D
Application will choose PCIFUNC1 as base/primary pcifunc
and as and when other pcifunc(secondary pcifuncs) gets
probed, this mailbox will be called and LMTST table will
be updated as:
PCIFUNC1 LMT_BASE_ADDR A
PCIFUNC2 LMT_BASE_ADDR A
PCIFUNC3 LMT_BASE_ADDR A
PCIFUNC4 LMT_BASE_ADDR A
On FLR lmtst map table gets resetted to the default lmt
base addresses for all secondary pcifuncs.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __assign_str macro has an unusual ending semicolon but the vast
majority of uses of the macro already have semicolon termination.
$ git grep -P '\b__assign_str\b' | wc -l
551
$ git grep -P '\b__assign_str\b.*;' | wc -l
480
Add semicolons to the __assign_str() uses without semicolon termination
and all the other uses without semicolon termination via additional defines
that are equivalent to __assign_str() with the eventual goal of removing
the semicolon from the __assign_str() macro definition.
Link: https://lore.kernel.org/lkml/1e068d21106bb6db05b735b4916bb420e6c9842a.camel@perches.com/
Link: https://lkml.kernel.org/r/48a056adabd8f70444475352f617914cef504a45.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
To avoid having memcpy() think a u64 "prof" is being written beyond,
adjust the prof member type by adding struct nix_bandprof_s to the union
to match the other structs. This silences the following future warning:
In file included from ./include/linux/string.h:253,
from ./include/linux/bitmap.h:10,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/cpumask.h:5,
from ./arch/x86/include/asm/msr.h:11,
from ./arch/x86/include/asm/processor.h:22,
from ./arch/x86/include/asm/timex.h:5,
from ./include/linux/timex.h:65,
from ./include/linux/time32.h:13,
from ./include/linux/time.h:60,
from ./include/linux/stat.h:19,
from ./include/linux/module.h:13,
from drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c:11:
In function '__fortify_memcpy_chk',
inlined from '__fortify_memcpy' at ./include/linux/fortify-string.h:310:2,
inlined from 'rvu_nix_blk_aq_enq_inst' at drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c:910:5:
./include/linux/fortify-string.h:268:4: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); please use struct_group() [-Wattribute-warning]
268 | __write_overflow_field();
| ^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c:
...
else if (req->ctype == NIX_AQ_CTYPE_BANDPROF)
memcpy(&rsp->prof, ctx,
sizeof(struct nix_bandprof_s));
...
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Subbaraya Sundeep<sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the return expression in the rvu_npc_fs.c
Signed-off-by: dingsenjie <dingsenjie@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added police action for ingress TC flower
hardware offload. With this rate limiting can be
done per flow. Since rate limiting is tied to
RQs in hardware the number of TC flower filters
with action as police is limited to number
of receive queues of the interface. Both bps
and pps modes are supported.
Examples to rate limit a flow:
$ ethtool -K eth0 hw-tc-offload on
$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 parent ffff: protocol ip \
flower ip_proto udp dst_port 80 action \
police rate 100Mbit burst 32Kbit
$ tc filter add dev eth0 parent ffff: \
protocol ip flower dst_mac 5e:b2:34:ee:29:49 \
action police pkts_rate 5000 pkts_burst 2048
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies all netdev_err messages in
tc code to NL_SET_ERR_MSG_MOD. NL_SET_ERR_MSG_MOD
does not support format specifiers yet hence
netdev_err messages with only strings are modified.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TC_MATCHALL ingress ratelimiting offload support with POLICE
action for entire traffic coming into the interface.
Eg: To ratelimit ingress traffic to 100Mbps
$ ethtool -K eth0 hw-tc-offload on
$ tc qdisc add dev eth0 clsact
$ tc filter add dev eth0 ingress matchall skip_sw \
action police rate 100Mbit burst 32Kbit
To support this, a leaf level bandwidth profile is allocated and all
RQs' contexts used by this interface are updated to point to it.
And the leaf level bandwidth profile is configured with user specified
rate and burst sizes.
Co-developed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for dumping current resource status of bandwidth
profiles and contexts of allocated profiles via debugfs.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K silicons supports hierarchial ingress packet ratelimiting.
There are 3 levels of profilers supported leaf, mid and top.
Ratelimiting is done after packet forwarding decision is taken
and a NIXLF's RQ is identified to DMA the packet. RQ's context
points to a leaf bandwidth profile which can be configured
to achieve desired ratelimit.
This patch adds logic for management of these bandwidth profiles
ie profile alloc, free, context update etc.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
