CN10K platforms uses RPM(0..2)_MTI_MAC100(0..3)_COMMAND_CONFIG
register for lmac TX/RX enable whereas CN9xxx platforms use
CGX_CMRX_CONFIG register. This config change was missed when
adding support for CN10K RPM.
Fixes: 91c6945ea1 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC on CN10K support hardware timestamping such that 8 bytes addition
header is prepended to incoming packets. This patch does necessary
configuration to enable Hardware time stamping upon receiving request
from PF netdev interfaces.
Timestamp configuration is different on MAC (CGX) Octeontx2 silicon
and MAC (RPM) OcteonTX3 CN10k. Based on silicon variant appropriate
fn() pointer is called. Refactor MAC specific mbox messages to remove
unnecessary gaps in mboxids.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed inconsistent license text across the RVU admin
function driver.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC on CN10K silicon support loopback for selftest or debug purposes.
This patch does necessary configuration to loopback packets upon receiving
request from LMAC mapped RVU PF's netdev via mailbox.
Also MAC (CGX) on OcteonTx2 silicon variants and MAC (RPM) on
OcteonTx3 CN10K are different and loopback needs to be configured
differently. Upper layer interface between RVU AF and PF netdev is
kept same. Based on silicon variant appropriate fn() pointer is
called to config the MAC.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPM supports below list of counters as an extension to existing counters
* class based flow control pause frames
* vlan/jabber/fragmented packets
* fcs/alignment/oversized error packets
This patch adds support to display supported RPM counters via debugfs
and define new mbox rpm_stats to read all support counters.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control configuration is different for CGX(Octeontx2)
and RPM(CN10K) functional blocks. This patch adds the necessary
changes for RPM to support 802.3 pause frames configuration on
cn10k platforms.
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIX uses unique channel numbers to identify the packet sources/sinks
like CGX,LBK and SDP. The channel numbers assigned to each block are
hardwired in CN9xxx silicon.
The fixed channel numbers in CN9xxx are:
0x0 | a << 8 | b - LBK(0..3)_CH(0..63)
0x0 | a << 8 - Reserved
0x700 | a - SDP_CH(0..255)
0x800 | a << 8 | b << 4 | c - CGX(0..7)_LMAC(0..3)_CH(0..15)
All the channels in the above fixed enumerator(with maximum
number of blocks) are not required since some chips
have less number of blocks.
For CN10K silicon the channel numbers need to be programmed by
software in each block with the base channel number and range of
channels. This patch calculates and assigns the channel numbers
to efficiently distribute the channel number range(0-4095) among
all the blocks. The assignment is made based on the actual number of
blocks present and also contiguously leaving no holes.
The channel numbers remaining after the math are used as new CPT
replay channels present in CN10K. Also since channel numbers are
not fixed the transmit channel link number needed by AF consumers
is calculated by AF and sent along with nix_lf_alloc mailbox response.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OcteonTx2's next gen platform the CN10K has RPM MAC which has a
different serdes when compared to CGX MAC. Though the underlying
HW is different, the CSR interface has been designed largely inline
with CGX MAC, with few exceptions though. So we are using the same
CGX driver for RPM MAC as well and will have a different set of APIs
for RPM where ever necessary.
This patch adds initial support for CN10K's RPM MAC i.e. the driver
registration, communication with firmware etc. For communication with
firmware, RPM provides a different IRQ when compared to CGX.
The CGX and RPM blocks support different features. Currently few
features like ptp, flowcontrol and higig are not supported by RPM. This
patch adds new mailbox message "CGX_FEATURES_GET" to get the list of
features supported by underlying MAC.
RPM has different implementations for RX/TX stats. Unlike CGX,
bar offset of stat registers are different. This patch adds
support to access the same and dump the values in debugfs.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
